Feasibility of Laminar Plasma-Jet Hardening of Cast Iron Surface

Nontransferred DC laminar plasma jets of stable flow and low impinging pressure acting on the substrate were used to heat W–Mo–Cu cast iron for phase transfer hardening of the surface layer. Substrates were heated in multipass with or without overlapping or heated with only single-pass. Surface morphologies of the molten trace and microstructure of the cross-section were observed, and the hardness distribution of the treated surface layer was examined. The surface layer of single-pass-heated specimen has an average hardness of about 900 HV0.1, while the specimen treated with multipass shows an average hardness of about 700 HV0.1, because of the heat effect from the neighboring pass treating, compared with the substrate hardness of about 300 HV0.1. The results demonstrate the stable and favorably controlled heating of the laminar plasma jet on the substrate surface and feasibility of using it as a tool for surface hardening of cast iron.

The damage evaluation of rigid particle filled polymer

In this paper, the rigid particle filled polymer is studied in the hope to understand the real damage mechanisms. Two damage parameters were introduced and measured. One is the macro-damage of the materials calculated from the modulus measured, another is micro-damage describing the interfacial debonding or the percentage of the particle debonded from the matrix. The damage rate of the macro damage decreases, while the micro damage increases with the applied stress.

Gain saturation effects of a flowing chemical oxygen-iodine laser

A new oxygen-iodine medium gain model is developed to include pumping and deactivation of the upper laser levels of the iodine atoms, hyperfine and translation relaxation, as well as the flowing effect. The rate equations for gain of a supersonic flowing cw oxygen-iodine laser (COIL) are described when the medium is stimulated by a single-mode field. The general solution of the self-consistency integral equation is obtained. The result shows that the saturation behaviour in low pressure of the COIL differs from both the inhomogeneous and homogeneous broadening, and exhibits an 'anomalous' saturation phenomenon.

Centrifuge modeling of suction bucket foundations for platforms under ice-sheet-induced cyclic lateral loadings

This paper presents the results of a series of centrifuge model tests performed to study the behavior of suction bucket foundations for a tension leg platform in the Bohai Bay, China. The target lateral loadings were from ice-sheet-induced structural vibrations at a frequency of 0.8-1.0 Hz. The results indicate that excess pore water pressures reach the highest values within a depth of 1.0-1.5 in below the mud line. The pore pressures and the induced settlement and lateral displacement increase with the amplitude of the cyclic loading. Two failure modes were observed: liquefaction in early excitations and settlement-induced problems after long-term excitations. (c) 2006 Elsevier Ltd. All rights reserved.

意大利威尼托（Veneto）的刺叶栎林-植物社会学生物多样性研究

刺叶栎( Quercus ilex L．)是地中海的常绿树种，属于古老的第三纪植物区系成份。本文根据苏黎世——蒙特利尔学派的植被学基本原理，全面地研究了分布在整个威尼托(Veneto)大区的剌叶栎林，详细研究刺叶栎林的群落组成、结构及类型划分。同时，对威尼托的刺叶栎林同北京山区的栎林进行了比较研究。最后，着重研究了威尼托刺叶栎林的生物多样性。 威尼托的刺叶栎林主要分布在亚得里亚海沿岸（包括Foci del Tagtiamento和Bosco Nordio e Rosolina Mare两地）、Lago di Garda和Colli Euganei。 在气候上，亚得里亚海沿岸属于半地中海气候。加尔达湖区域(Laqo di Garda)则是接近欧洲中部的大陆性气候，且维持半地中海的气候特点。Co t l i Euganei是这两地气候的过渡类型，且更接近亚得里亚海沿岸的类型。 在亚得里亚海沿岸的刺叶栎林可以分为三类，第一类(I)是一些矮树丛，这是Fraxinus ornus和Quercus ilex混交林的前身，较干旱。第二类群落(II)缺少乔木层，灌木层是由一些盖度不大的刺叶栎代替，更干旱。第三类群落(Ⅲ)是一群在外貌上相同的成熟群落．Fraxinus ornus和Quercus ilex得到充分发展，较中生。 在加尔达湖区的刺叶栎林可划分为三类。第一类群落(I)代表一组耐旱、开敞的矮树丛，含有Sesterio Variae-Ostryelum群丛的特征种，这一类可划分为SesLerio Variae-Ostryetum群 丛，土壤贫脊和干旱。第二类群落(Ⅱ)代表一类较郁闭的矮树丛，含有较多的Prunetalia群落目的成份，土壤较贫脊。第三类群(Ⅲ)代表一类郁闭的群落，乔木具有很大的密度因而林下灌木不能充分发展。SesLerio Variae-Ostryetum群丛和Prunetalia群落目的成份均不多。 在Colli Euganei的刺叶栎林可划分为二类。第一类群落(I)是一些不郁闲的矮树林组成。大体上分为地中海旱生栎林和地中海假灌丛。第二类群落(II)代表了较中生状态的植被，刺叶标种群绝对郁闭。 北京地处华北大平原的西北部。北京山地的气候为温带陆地性季风气候，其地带性的落叶阔叶林是以栎林为典型。虽然这些栎林同意大利威尼托刺叶栎林是两种不同的森林类型，但两者之间是存在着一定的联系。其共有的科有20个，共有属有11个。他们在植物组成中，以禾本科，蔷薇科和豆科的植物种类为最多。在乔木层中，他们都是以壳斗科的栎属(Quercus)为优势，其中木犀科的白蜡属(Fraxinus)和槭树属(Acer)较多。 本文对威尼托大区刺叶栎林的物种多度分布格局进行了全面探讨，计算出刺叶栎林的几何分布模型、Broken-stick分布模型、Log分布模型、Log-normat分布模型等四种物种多度分布的理论模型，并将这些理论分布模型用“序列／多度”图解和“多度／频度”图解表示出来。其中，几何分布模型．Broken-stick1分布模型用“序列／多度”图解表示。Broken-stick2分布模型、Log分布模型、Log-normal分布模型用“多度／频度”图解表示。 对上述四个物种多度的理论分布同实际现察的物种多度分布进行X2分析，在5％的显著性水平上，对整个威托大区的刺叶 栎林，几何分布模型最能代表其物种多度分布，显著性最大;Log-normal分布模型也可以用来代表威尼托刺叶标妹的物种多度分布，其显著性次于几何分布模型的显著性。这表明威尼托的刺叶栎林尚处于演替的早期阶段，这些刺叶栎林曾受到严重破坏，现正在恢复。 通过比较Foci del Tagtiamento和Bosco Nordio加尔达湖区、Colli Euganei四个地方刺叶栎林的物种多度的几何分布模型和Log-normal分布模型，显示出Lago di Garda（加尔达湖区）的刺叶栎林生物多样性最好、Foci del Tagtiamento刺叶栎林生物多样性较好．Bosco Nordio的剌叶栎林生物多样性较差．Colli Euganei的刺叶栎林生物多样性最差。 再利用多样性指数计算全部威尼托大区剌叶栎林的生物多样性。计算的多样性指数有丰富度指数（包括Margalef指数、Men-hinick指数、Monk指数）、多样性指数(Shannon信息指数、Bri llouin个息指数、Gini指数、PIE指数、Mcintosh指数)、优势度指数(Berger-Parker指数、Simpson指数)、均一度指数(Pielou均一度指数、Brillouin均一度指数，PIE的V’均一度指数．PIE的V均一度指数，N2的V’均一度指数，N2的V均一度指数，Mclntosh均一度指数，Hill的F10均一度指数，Hill的E21均一度指数，Hill的F21的一度指数）。通过比较丰富度指数，多样性指数、均一度指数与优势度之间的关系，结果，Simpson优势度指数同Men-hinick物种丰富度指数、Shannon信息指数、Bril-louin信息指数、Pielou均一度指数，Brillouin均一度指数，Mcintosh均一度指数、PIE的V’均一度指数呈负相关关系，因此，上述生物多样性指数可以较好地反映威尼托大区刺叶栎林的生物多样性。反映出的结果是：加尔达湖区刺叶栎林生物多样性最好，Foci del Tagtiamento刺叶栎林生物多样性较好，Bosco Nordio的剌叶栎林生物多样性较差．Colli Euganei的刺叶栎林生物多样性最差。 生物多样性的研究显示出生物多样性同生境状况的密切联系。往往受人为干扰严重的群落生物多样性低、如Coli Euganei和亚得里亚海岸刺叶栋林;而受人为破坏较轻的群落其生物多样性高，如加尔达湖区刺叶栎。 生物多样性的研究还显示出生物多样性同群落演替的发展阶段密切相关，在群落演替初期，由于缺乏优势种，而又有大量物种侵入，物多样性相对较高。在群落演替中期，由于形成了一个或几个优势种，优势度的增加导致了生物多样性相对减低。如Foci del Tagtiamento刺叶栎林生物多样性高于Bosco Nordio刺叶栎林的生物多样性。到演替后期，随着更多物种的侵入，群落结构的复杂化、生物多样性又将逐步提高。

A revision of the white-toothed shrews (Crocidura) of Southern China

Many systematic relationships among Chinese white-toothed shrews of genus Crocidura are presently unresolved. In this paper, a taxonomic revision of Crocidura from Southern China is presented. We studied 338 specimens from Burma, China, Korea, Pakistan, Turkey, Middle and Central Asia, and Russia (Appendix I), 285 of which had complete skulls that were analyzed with principal component and discriminant analyses. Results indicated that 6 species of Crocidura can be recognized in South China. C. fuliginosa occurs in Southwestern and Eastern China, C. attenuata is broadly distributed throughout Southern China, and C. horsfieldii is restricted to the southern part of China. C vorax and C. rapax, usually placed as synonyms of the European C russula, are recognized as 2 valid species whose ranges overlap in Southwestern China. C. shantungensis of Eastern Asia extends to the northern part of Southern China and is distinct from C. suaveolens and C. gmelini of Middle and Central Asia, respectively.

蛇毒因子消耗补体对大鼠同种心脏移植急性排斥反应的影响

探讨蛇毒因子(CW)消耗补体对大鼠同种心脏移植急性排斥反应的影响。方法建立Wistar至sD大 鼠同种异位心脏移植模型，实验组经静脉注射CVF以消耗受体血清中补体，观察移植心存活时间，并从实验组和对照组中分别 抽取5只大鼠于术后1、3、5、6、7 d定时活杀，对比观察移植心急性排斥反应程度，血清补体活性以及CIM+、CD8+T细胞浸润程 度。结果使用CVF的实验组，其移植一fi,存活时间显著延长，平均达(32．39±23．82)d，部分移植心甚至达到长期存活，而对照 组为(6．60±0．65)d(P<0．01)，病理检查及免疫组化证实实验组急性排斥反应程度、组织内C3沉积情况和CD4+、CD8+T细胞 浸润程度均较同期对照组明显减轻。结论CVF清除补体可抑制大鼠同种心脏移植急性排斥反应，显著延长移植心存活 时间。

Fabrication of low-cost and high-reflectivity bottom mirrors for Si-based micro-cavity devices

A novel and simple way to prepare high-reflectivity bottom mirrors for Si-based micro-cavity devices is reported. The bottom mirror was deposited in the hole, which was etched from the backside of the sample by ethylenediamine-pyrocatechol-water solution with the buried Sio, layer in the silicon-on-insulator substrate as the etching-stop layer. The high-reflectivity of the bottom mirror deposited in the hole and the narrow hill width at half maximum of the cavity formed by this method both indicate the successful preparation of the bottom mirror for Si-based micro-cavity devices.

国产万亿次机群系统NPB性能测试分析

对3个国产万亿次机群系统进行了NPB性能测试分析,重点研究大规模并行处理时(处理器数目达到上千个)的性能特点和趋势.分析了不同的处理器、互连网络等系统配置对NPB性能的影响,发现NPB的8个程序在3个万亿次机器上的性能特点和表现并不一致,表明国产高性能机群在设计上正在逐渐走出同质化的趋势,向多样化发展.进一步分析表明,目前NPB程序的可扩展性可以达到几百个处理器,但尚不能达到上千个处理器,NPB程序能发挥出的系统峰值的百分比仍然徘徊在10%左右,机群系统的并行可扩展性和应用程序对机器运算潜能的利用还需要进一步提高.对于处理器数目达到上千个的万亿次机群系统来说,对集合通信和细粒度通信能力的支持亟需提高.

燃料气中H_2、N_2、O_2、CH_4、CO、O_2的全分析

从生物质汽化制取的燃料气，其主要成份是 CO_2、H_2、O_2、N_2、CH_4、CO 六种气体。但在不同的工艺条件下，各组份的含量差异很大。在工艺试验中，需要及时监测各种组份含量的变化，摸索最佳工艺条件，这就要求缩短分析周期。为此我们改装了一台 SP-2307色谱仪。用 Ar 作载气，只用一个热导检测器，一次进样就可完成上述六种气体的分析。改装时增加气体自动进样系统，提高了分析的准确度。