STRUCTURE INVESTIGATION OF TI(OBU)4-ALET3 CATALYST BEFORE AND AFTER HEAT-TREATMENT

The catalyst structure of Ti(OBu)4-AlEt3 at different Al/Ti ratios before and after heat aging has been investigated from the data of UV, GC-MS, ESR and C-13 NMR spectra. The complex compounds formed by HTiEt2 and AlEt2(OBu) exist mainly in the catalyst solution, and no -OBu ligands linking with Ti atoms can be found at an Al/Ti ratio of four before heat aging. Many kinds of catalytic species with different size are formed after heat aging the catalyst at 110-degrees-C for 2 h. Dehydrogenation, accompanied by the valence change from Ti3+ to Ti2+, is observed during the aging process of the catalyst.

非晶态TiO_2-SiO_2网络缺陷和Ti配位结构的ESR研究

在SiO_2中掺杂其它原子会导致熔石英SiO_4四面体网络部分破坏,形成缺陷。主要缺陷有非桥氧,E′心和过氧基。非桥氧为仅与一个Si原子(或Ti原子)成单键的O原子。E′心为与三氧配位的Si原子。剩余一个未配对的印杂化电子形成悬键轨道。过氧基则为游离氧被非桥氧俘获,或非桥氧彼此俘获而形成的。这三种缺陷各有一个未配对电子,因而具有

Effect of Process Conditions on Microstructure and Corrosion Resistance of Cold-Sprayed Ti Coatings

Ti and Ti alloys can be applied to steels as a protective coating in view of its excellent resistance to corrosive environment. Cold spraying, as a new coating technique, has potential advantages in fabrication of Ti coating in comparison with conventional thermal spraying techniques. In this study, Ti coatings were prepared on carbon steel substrates by cold spraying via controlling the process conditions. The microstructure of coatings was observed by SEM. The porosity of coatings was estimated by image analysis and the bond strength was tested for comparison of the process conditions. Potentiodynamic polarization and open-circuit potential (OCP) measurements were performed to understand the corrosion behavior of the coatings. The SEM examination shows that the coatings become more compact with the increases of pressure and temperature of driving gas. The potentiodynamic polarization curves indicate that the coating which has lower porosity has lower corrosion current. The polarization and OCP measurement reveal that cold-sprayed Ti coating can provide favorable protection to carbon steel substrate. The polishing treatment of coating surface polishes the rough outer layer including the small pores as well as decreases the actual surface area of the coating, leading to the considerable improvement of corrosion resistance.

KEL-TI介质的地震波场响应与成像方法研究

To deal with the problems in multi-component converted seismic wave exploration in coal fields, the wave propagating features and imaging methods of multi-component converted waves in coal measure strata are researched in this thesis firstly. The relations between viscoelasticity and anisotropy in coal measure strata are analyzed to build KEL-TI model, and which seismic wave propagating and attenuating features are researched. The disadvantages of converted wave imaging methods based on common converted point gather are analyzed and constant velocity no NMO converted wave imaging method based on common scattering point gather is put forward, according to Huygens-Fresnel principle, which applicabilities in the elastic isotropic, elastic TI and KEL-TI situations are discussed. To different model simulation data, the common scattering point gathers’ and stacked profiles’ features are analyzed. The results show that the method can image compressional waves and converted waves with high precision. Secondly, the resolution enhancing theories and methods of converted wave are researched by Rayleigh wave suppressing, converted wave static correction and poststack inverse-Q filtering. 1) The polarization filter is designed by the instantaneous polarization information of seismic waves, and the Rayleigh wave suppressing method is researched. From the spectrum analysis before and after filtering, it can be derived that the amplitudes are kept relatively. 2) To constant velocity no NMO converted wave imaging method, the static correction method based on common equivalent offset point gather is put forward and tested to the actual converted waves. 3) The relation between equivalent quality factor of converted wave, compressional wave quality factor and the ratio of compressional to shear wave velocity is derived. The compressional wave quality inversion method by first arrivals of none-offset VSP is researched, and which is then transformed to the equivalent quality factor to perform inverse-Q filtering of actual converted waves. The result has shown that the method can recover the high frequency energy of converted waves. At last, the theories and methods researched in this thesis are practiced to the 3D3C seismic exploration in Guqiao coal mine in Huainan and achieve good results.

Epoxidation of cyclohexene on Ti/SiO2 catalysts prepared by chemical grafting TiCl4 on deboronated silica xerogel

Ti/SiO2 (or Ti/de[B]SiO2) catalysts were prepared by grafting deboronated silica xerogel with gaseous TiCl4. Using TBHP as oxidant, the Ti/de[B]SiO2 catalyst shows both catalytic activity and selectivity in epoxidation of cyclohexene better than 80%, and the activity can be comparable with that of Ti-beta. The catalytic activity of Ti/de[B]SiO2 strongly depends on the content of B of support precursor, and the pretreatment temperature of the support. IR studies show that the sites in the deboronated silica xerogel to react with TiCl4 are not only the silanol nests, but also the defect sites produced during the deboronation. (C) 2001 Elsevier Science B.V. All rights reserved.