梯度涂层材料中裂纹问题的非均匀元分析

本文采用非均匀等参有限元的方法研究了薄膜梯度涂层/均匀基材中的界面裂纹问题，并与双材料界面裂纹情况进行了对比计算。研究表明：在均匀基材上采用梯度涂层，与双材料相比可以有效地降低裂尖场应力强度因子；同时还分析了涂层厚度与梯度参数对界面应力强度因子的影响。结果表明：当薄膜厚度大于或等于裂纹长度时，应力强度因子（K_I、K_(II)）对其尺度的变化显得不敏感；对梯度参数的影响而言，当材料性能曲线的幂指数m大于1时，裂尖场的应力强度因子K_(II)相对K_I很小且基本不随m变化，因此裂尖场与均匀材料情况类似；当m小于1时，应用强度因子K_(II)随m减小而急剧增大，裂尖场由K_I及K_(II)控制，断裂趋于混合型。

亚微米氮化钛膜的纳米压痕和划痕测定

采用等离子电弧沉积的方法，分别在GT35和40CrNiMo钢上沉积厚约为0.5μm的氮化钛(TiN)膜。为了筛选基材，采用纳米压痕和划痕技术，评价膜基界面结合和固体润滑效果。纳米压痕结果，GT35，40CrNiMo和TiN的纳米硬度/弹性模量的典型值分别约为11.5 GPa/330GPa, 6.0 GPa/210GPa, 30GPa/450GPa。纳米划痕结果，GT35有较理想的膜基结合能力；GT35，40CrNiMo，TiN及其有机膜的磨擦系数分别约为0.25，0.45，0.15, 0.10。同40CrNiMo相比，GT35是较为理想的基体材料。纳米压痕和划痕技术能提供丰富的近表面的弹塑性变形、断裂和磨擦等的信息，是评价亚微米薄膜力学性能的有效手段。

热障涂层材料性能和失效机理研究进展

热障涂层材料破坏由大尺度屈曲和层离机制产生，而这些机制又是微裂纹形核、扩展及相互连通结果的积累。由于特殊制备工艺和使用环境，材料性能涉及到许多特殊机制。近半个世纪的研究，人们对其性能有了充分认识。综述近几年的研究结果，内容包括：热生长氧化现象及其热力学描述；热生长应力与材料失效的联系；材料破坏机理与性能控制参数组织的联系；微缺陷演化产生的材料屈曲和层离所需的能量释放率；破坏准则、服役寿命预计模型和评价标准等。

Formation and Structure of Composite Coating of HAD and Micro-Plasma Oxidation on A3 Steel

Composite coatings were obtained on A3 steel by hot dipping aluminum(HAD) at 720 degreesC for 6 min and micro-plasma oxidation (MPO) in alkali electrolyte. The surface morphology, element distribution and interface structure of composite coatings were studied by means of XRD, SEM and EDS. The results show that the composite coatings obtained through HAD/MPO on A3 steel consist of four layers. From the surface to the substrate, the layer is loose Al2O3 ceramic, compact Al2O3 ceramic, At and FeAl intermetallic compound layer in turn. The adhesions among all the layers are strengthened because the ceramic layer formed at the At surface originally, FeAl intermetallic compound layer and substrate are combined in metallurgical form through mutual diffusion during HAD process. Initial experiment results disclose that the anti-corrosion performance and wear resistance of composite coating are obviously improved through HAD/MPO treatment.

The Effect of the Thickness of Fe2 Al5 Phase Layer at Fe/Al Interface on the Mechanics Behavior of Hot Dip Aluminizing Coating

Hot Dip Aluminized Coatings with different thickness were prepared on Q235 steel in aluminum solutions with different temperature for certain time. Through tensile tests and in-situ SEM observations, the effect of the coating's microstructure on the tensile strength of the samples was studied. It was disclosed at certain aluminum solution temperature,transaction layers mainly composed of Fe2 Al5 phase got thicker with time prolonging, and this changed initial crack's extending direction from parallel with to vertical with stretching direction. The change in crack direction decreased tensile strength of samples, thus made the coating easy to break. It was concluded that the existence of thick Fe2 Al5 phase layer was the basic reason for the lowering of tensile strength of the coating.

固体力学进展及应用: 庆贺李敏华院士90华诞文集

《固体力学进展及应用：庆贺李敏华院士90华诞文集》收录了近代固体力学基础理论及其应用领域的重要科技成果和最新进展。作者是在同体力学领域工作多年的资深研究员，他们来自各行各业，有丰富的科研与丁作经验。他们提供的论文在相当程度上反映当前同体力学的发展现状与成就，并能看出发展趋势，对未来研究的课题选择有参考价值。《固体力学进展及应用：庆贺李敏华院士90华诞文集》还收集了李敏华院士的珍贵照片和纪念李敏华院士90华诞的庆贺和回忆文章，具有重要的史料价值。

Development And Characterization Of Composite Ni-Cr-C-Caf2 Laser Cladding On Gamma-Tial Intermetallic Alloy

A process of laser cladding Ni-CF-C-CaF2 mixed powders to form a multifunctional composite coatingd on gamma-TiAl substrate was carried out. The microstructure of the coating was examined using XRD, SEM and EDS. The coating has a unique microstructure consisting of primary dendrite or short-stick TiC and block Al4C3 carbides reinforcement as well as fine isolated spherical CaF2 solid lubrication particles uniformly dispersed in the NiCrAlTi (gamma) matrix. The average microhardness of the composite coatings is approximately HV 650 and it is 2-factor greater than that of the TiAl substrate. (C) 2008 Elsevier B.V. All rights reserved.

On The Thermally Induced Cracking Of A Segmented Coating Deposited On The Outer Surface Of A Hollow Cylinder

In this work, the thermally induced cracking behavior of a segmented coating has been investigated. The geometry under consideration is a hollow cylinder with a segmented coating deposited onto its outer surface. The segmentation cracks are modeled as a periodic array of axial edge cracks. The finite element method is utilized to obtain the solution of the multiple crack problem and the Thermal Stress Intensity Factors (TSIFs) are calculated. Based on dimensional analysis, the main parameters affecting TSIFs are identified. It has been found that the TSIF is a monotonically increasing function of segmentation crack spacing. This result confirms that a segmented coating exhibits much higher thermal shock resistance than an intact counterpart, if only the segmentation crack spacing is narrow enough. The dependence of TSIF on some other parameters, such as normalized time, segmentation crack depth, convection severity as well as material constants, has also been discussed. (C) 2008 Elsevier B.V. All rights reserved.

The mechanism of PEO process on Al–Si alloys with the bulk primary silicon

This study focuses on mechanism of ceramic coating on Al-Si alloys with bulk primary Si using plasma electrolytic oxidation (PEO) technology. Al-Si alloys with 27-32% Si in weight were used as substrates. The morphologies, composition and microstructure of PEO coatings were investigated by scanning electron microscopy (SEM) with energy dispersive X-ray system (EDX). Results showed that the PEO process had four different stages. The effect of bulk Si is greatly on the morphology and composition of coatings at first three stages. Anodic oxide films formed on Al and Si phases, respectively. When the voltage exceeded 40 V, glow appeared and concentrated on the localized zone of interface of Al and Si phase. Al-Si-O compounds formed and covered on the dendrite Si phase surface, and the coating on bulk Si, which was silicon oxide, was rougher than that on other phase. If the treatment time was long enough, the coatings with uniform surface morphologies and elements distribution will be obtained but the microstructure of inner layer is looser due to the bulk Si.

On a novel method of impact by a front-end-coated bullet to evaluate the interface adhesion between film and substrate

A preliminary experiment was carried out to validate the feasibility of the method of impact by a front-end-coated bullet to evaluate the interface adhesion between film and substrate. The theoretical description of the initiation, propagation and evolution of the stress pulse during impact was generalized and formulized. The effects of the crucial parameters on the interface stress were further investigated with FEM. The results found the promising prospect of the application of such a method and provided useful guidance for experimental design.

裂缝光纤传感的工程应用

光纤传感的灵敏性及工程"存活率"是其工程实用化的两个关键技术参量,对光纤-混凝土结构两种常用裂缝光纤传感光信号对裂缝宽度的灵敏性与存活率进行了实验研究,对光纤涂覆层对灵敏性影响的大小和机理进行了分析,并制作了灵敏性与存活率均较高的光纤试验样本,与裂缝成45°夹角时,相比于等直径的普通二次涂覆粗光纤(10/125/900μm),样本的灵敏性提高近65%,而存活率亦高出约15%。研究结果可为裂缝光纤传感的优化设计和工程应用提供了基本参照。

光纤涂敷层对光纤裂缝传感器分布式监测能力的影响

基于混凝土模型试验，对涂敷层的传感光纤的裂缝复用能力进行了定量分析，得到了传感光纤和工程结构裂缝夹角在30°，45°，60°时的复用能力与裂缝宽度的关系曲线。对由软性材料构成的光纤涂敷层来说，光纤的复用能力随涂敷层厚度的增加而增大，在与裂缝夹角成45°时，二次涂敷粗光纤的复用能力约为细光纤的5倍，表明光纤敷层对光纤裂缝监测的复用能力具有较大影响。对这种影响的机理进行了理论分析和试验研究，发现当混凝土开裂时，光纤沿混凝土界面的滑移是光纤涂敷层影响光纤裂缝复用能力的主要原因，在光纤与裂缝夹角成45°时，这一影

溶胶-凝胶多孔二氧化硅减反膜稳定性研究

多孔SiO2膜层经热处理后，具有很高的激光破坏阈值，但是结构中有许多Si-OH亲水基团，导致光学透过率受环境相对湿度的影响很大。实验目的是改善膜层内部结构，使膜层结构中的亲水基团转变为疏水基团。提高膜层的疏水性，增强膜层的透过率稳定性。系统地研究了膜层透过率随时间变化的规律，在氨气和六甲基二硅氮烷(HMDS)混合气氛下热处理膜层，处理后生成Si-O-Si(CH2)3非极性疏水基团，使膜层的疏水性大大提高，因而膜层的透过率稳定性有大幅度提高。稳定性的提高延长了膜层的寿命。处理后膜层的表面粗糙度良好，均方根表

掺入有机硅提高溶胶-凝胶二氧化硅减反膜的稳定性研究

膜层稳定性对于激光器能否长期稳定使用极为重要。多孔SiO。减反膜经热处理后，结构中还存在许多Si—OH亲水基团，透过率稳定性受环境相对湿度的影响较大。向膜层中掺入有机硅，添加疏水基团，提高了膜层的疏水性，增强了膜层的透过率稳定性。膜层中加了Si-CH3疏水基团，膜层的疏水性大大提高；当Si-CH3与二氧化硅悬胶体中的Si的摩尔比为1／5．7时，即Si—CH3质量分数为0．35％时的二氧化硅膜层，其减反效果好，疏水性也高，从而大幅度提高了膜层的透过率稳定性，延长了膜层的寿命，对二氧化硅膜层具有高激光损伤阈值

磷酸盐激光玻璃凝胶防潮膜和减反膜

采用溶胶-凝胶方法制备（CH3）2Si（OC2H5）2预聚体涂膜液以及掺入SiO2悬胶体涂膜液改性，采用旋转法在掺钕磷酸盐激光玻璃棒端面涂制防潮膜，热处理后膜层固化。SiO2改性的CH3O防潮膜，热处理后的膜层耐摩擦性能明显改善。然后旋转涂制第二层多空性SiO2减反膜，涂膜胶体通过硅酸乙脂碱催化水解缩聚制得，减反膜的折射率为约1．25，玻璃棒涂膜后激光波长1053nm减少表面反射率6．5％-7．5％，双层膜激光破坏阈值12J／cm^2，1053nm／1ns，膜层表面粗糙度（RMS）2．523nm。直径20