Calculation of propagation loss in photonic crystal waveguides by FDTD technique and Pade approximation

The propagation losses in single-line defect waveguides in a two-dimensional (2D) square-lattice photonic crystal (PC) consisted of infinite dielectric rods and a triangular-lattice photonic crystal slab with air holes are studied by finite-difference time-domain (FDTD) technique and a Pade approximation. The decaying constant beta of the fundamental guided mode is calculated from the mode frequency, the quality factor (Q-factor) and the group velocity v(g) as beta = omega/(2Qv(g)). In the 2D square-lattice photonic crystal waveguide (PCW), the decaying rate ranged from 10(3) to 10(-4) cm(-1) can be reliably obtained from 8 x 10(3)-item FDTD output with the FDTD computing time of 0.386 ps. And at most 1 ps is required for the mode with the Q-factor of 4 x 10(11) and the decaying rate of 10(-7) cm(-1). In the triangular-lattice photonic crystal slab, a 10(4)-item FDTD output is required to obtain a reliable spectrum with the Q-factor of 2.5 x 10(8) and the decaying rate of 0.05 cm(-1). (c) 2004 Elsevier B.V. All rights reserved.

Fabrication and analysis of 2x2 thermo-optic SOI waveguide switch with low power consumption and fast response by anisotropy chemical etching

A low power consumption 2 x 2 thermo-optic switch with fast response was fabricated on silicon-on-insulator by anisotropy chemical etching. Blocking trenches were etched on both sides of the phase-shifting arms to shorten device length and reduce power consumption. Thin top cladding layer was grown to reduce power consumption and switching time. The device showed good characteristics, including a low switching power of 145 mW and a fast switching speed of 8 +/- 1 mus, respectively. Two-dimensional finite element method was applied to simulate temperature field in the phase-shifting arm instead of conventional one-dimensional method. According to the simulated result, a new two-dimensional index distribution of phase-shifting arm was determined. Consequently finite-difference beam propagation method was employed to simulate the light propagation in the switch, and calculate the power consumption as well as the switching speed. The experimental results were in good agreement with the theoretical estimations. (C) 2004 Elsevier B.V. All rights reserved.

Resonant cavity based compact efficient antireflection structures for photonic crystals

We propose an effective admittance ( EA) method to design antireflection structures for two-dimensional photonic crystals (PCs). We demonstrate that a compact and efficient antireflection structure, which is difficult to obtain by the conventional admittance matching method, can be readily designed by the EA method. The antireflection structure consists of an air slot resonant cavity that is constructed only with the materials that constitute the PC. Compared with a bare PC, the reflection from a PC with an antireflection structure is reduced by two orders of magnitude over a wide bandwidth. To confirm the presented EA method, finite-difference time-domain (FDTD) simulations are performed, and the results from the FDTD and the EA method are in good agreement.

Dynamics of spin-dependent tunneling through a semiconductor double-barrier structure

The dynamics of spin-dependent tunneling through a nonmagnetic semiconductor double-barrier structure is studied including the k(3) Dresselhaus spin orbit coupling is solved by the time-dependent Schrodinger equation with a developed method for the finite-difference relaxation. The resonant peak and quasibound level lifetime are determined by the in-plane wave vector and the applied electric field. The buildup time and decay lifetime of resonant probability amplitude are different for the spin-down and spin-up electrons due to the Dresselhaus spin-orbit coupling. Further investigation shows that the steady spin-polarization in both the well and collector regions has been obtained in the time domain. (C) 2007 American Institute of Physics.

Design, fabrication, and characterization of an ultracompact low-loss photonic crystal corner mirror

An ultracompact, low-loss, and broad-band corner mirror, based on photonic crystals, is investigated in this paper. Based on the theoretical analysis of the loss mechanism, the boundary layers of the photonic crystal region are revised to improve the extra losses, and the transmission characteristics are evaluated by using the 3-D finite-difference time-domain method. The device with optimized structure was fabricated on silicon-on-insulator substrate by using electron-beam lithography and inductively coupled plasma etching. The measured extra losses are about 1.1 +/- 0.4 dB per corner mirror for transverse-electronic polarization for the scanning wavelength range of 1510-1630 nm. Dimensions of the achieved PC corner mirror are less than ;7 x 7 mu m(2), which are only about one tenth of conventional wave-guide corner mirrors.

Symmetry analysis and numerical simulation of mode characteristics for equilateral-polygonal optical microresonators

Mode characteristics for two-dimensional equilateral-polygonal microresonators are investigated based on symmetry analysis and finite-difference time-domain numerical simulation. The symmetries of the resonators can be described by the point group C-Nv, accordingly, the confined modes in these resonators can be classified into irreducible representations of the point group C-Nv. Compared with circular resonators, the modes in equilateral-polygonal resonators have different characteristics due to the break of symmetries, such as the split of double-degenerate modes, high field intensity in the center region, and anomalous traveling-wave modes, which should be considered in the designs of the polygonal resonator microlasers or optical add-drop filters.

Mode coupling between first- and second-order whispering-gallery modes in coupled microdisks

The mode characteristics for two coupled microdisks are investigated by the finite-difference time-domain technique. In the two coupled micodisks, mode coupling between the same order whispering-gallery modes (WGMs) results in coupled WGMs with split mode wavelengths. The numerical results show that the split mode wavelengths of the coupled first- and second-order WGMs can have a crossing point in some cases, which can induce anticrossing mode coupling between them and greatly reduce the mode Q factor of the coupled first-order WGMs. The time variation of mode field pattern shows the transformation between the coupled first- and second-order WGMs. (C) 2007 Optical Society of America

Prediction and suppression of strong dispersive coupling in microracetrack channel drop filters

For a four-port microracetrack channel drop filter, unexpected transmission characteristics due to strong dispersive coupling are demonstrated by the light tunneling between the input-output waveguides and the resonator, where a large dropping transmission at off-resonance wavelengths is observed by finite-difference time-domain simulation. It causes a severe decline of the extinction ratio and finesse. An appropriate decrease of the coupling strength is found to suppress the dispersive coupling and greately increase the extinction ratio and finesse, a decreased coupling strength can be realized by the application of an asymmetrical coupling waveguide structure. In addition, the profile of the coupling dispersion in the transmission spectra can be predicted based on a coupled mode theory analysis of an equivalent system consisting of two coupling straight waveguides. The effects of structure parameters on the transmission spectra obtained by this method agree well with the numerical results. It is useful to avoid the strong dispersive coupling region in the filter design. (c) 2007 Optical Society of America.

Mode analysis and Q-factor enhancement due to mode coupling in rectangular resonators

Modes in rectangular resonators are analyzed and classified according to symmetry properties, and quality factor (Q-factor) enhancement due to mode coupling is observed. In the analysis, mode numbers p and q are used to denote the number of wave nodes in the direction of two orthogonal sides. The even and odd mode numbers correspond to symmetric and antisymmetric field distribution relative to the midlines of sides, respectively. Thus, the modes in a rectangle resonator can be divided into four classes according to the parity of p and q. Mode coupling between modes of different classes is forbidden; however, anti-crossing mode coupling between the modes in the same class exists and results in new modes due to the combination of the coupled modes. One of the combined modes has very low power loss and high Q-factor based on far-field emission of the analytical field distribution, which agrees well with the numerical results of the finite-difference time-domain (FDTD) simulation. Both the analytical and FDTD results show that the Q-factors of the high Q-factor combined modes are over one order larger than those of the original modes. Furthermore, the general condition required to achieve high-Q modes in the rectangular resonator is given based on the analytical solution.

Numerical study of a high-resolution far-field scanning optical microscope via a surface plasmon-modulated light source

In this paper, we analyze light transmission through a single subwavelength slit surrounded by periodic grooves in layered films consisting of An and dielectric material. A subwavelength grating is scanned numerically by the finite difference time domain method in two dimensions. The results show that the transmission field can be confined to a spot with subwavelength width in the far field and can be useful in the application of a high-resolution far-field scanning optical microscope.

Plasmonic surface-wave splitter

The authors present an analysis of a plasmonic surface-wave splitter, simulated using a two-dimensional finite-difference time-domain technique. A single subwavelength slit is employed as a high-intensity nanoscale excitation source for plasmonic surface waves, resulting in a miniaturized light-surface plasmon coupler. With different surface structures located on the two sides of the slit, the device is able to confine and guide light waves of different wavelengths in opposite directions. Within the 15 mu m simulation region, it is found that the intensity of the guided light at the interface is roughly two to eight times the peak intensity of the incident light, and the propagation length can reach approximately 42 and 16 mu m and at the wavelengths of 0.63 and 1.33 mu m, respectively. (c) 2007 American Institute of Physics.

A proposal for low cross-talk square-lattice photonic crystal waveguide intersection utilizing the symmetry of waveguide modes

We propose an approach to construct waveguide intersections with broad bandwidth and low cross-talk for square-lattice photonic crystals. by utilizing a vanishing overlap of the propagation modes in the waveguides created by defects which support dipole-like defect modes. The finite-difference time-domain method is used to simulate the waveguide intersection created in the two-dimensional square-lattice photonic crystals. Over a bandwidth of 30 nm with the center wavelength at 1300 nm, transmission efficiency above 90% is obtained with cross-talk below -30 dB. Especially, we demonstrate the transmission of a 500-fs pulse at 1.3 Am through the intersection, and the pulse after transmission shows very little distortion while the cross-talk remains at low level meantime. (c) 2006 Elsevier B.V. All rights reserved.

Optical interleaver based on directional coupler in a 2D photonic crystal slab with triangular lattice of air holes

A small-size optical interleaver based on directional coupler in a 2D photonic crystal slab with triangular lattice of air holes is designed and theoretically simulated using plane wave expansion and finite-difference time-domain method. The interleaver is formed by two parallel and identical photonic crystal slab waveguides which are separated by three rows of air holes. The coupling region is designed below the light line to avoid vertical radiation. The simulated results show that the coupling coefficient is increased and the final length of the interleaver is decreased by enlarging the radius of the middle row of air holes. The transmission properties are analyzed after the interleaver's structure is optimized, and around 100 GHz channel spacing can be got when the length of the interleaver is chosen as 40.5 mu m. (c) 2006 Elsevier B.V. All rights reserved.

Effect of disorder on self-collimated beam in photonic crystal

We report a numerical analysis of various types of disorder effects on self-collimated beam in two-dimensional photonic crystal. Finite-difference time-domain (FDTD) method is used to simulate the process by using a pulse propagation technique. The position disorders along the directions parallel and perpendicular to the incidence are considered. We show that random disorder along the perpendicular direction will have a lesser effect on the performance of the dispersion waveguides than those along the parallel direction. Furthermore, the self-collimation waveguide (SCW) has new characteristics when compared with the photonic crystal line defect waveguide. (c) 2006 Elsevier B.V. All rights reserved.

Design of two-dimensional photonic crystal edge emitting laser for photonic integrated circuits

An edge emitting laser based on two-dimensional photonic crystal slabs is proposed. The device consists of a square lattice microcavity, which is composed of two structures with the same period but different radius of air-holes, and a waveguide. In the cavity, laser resonance in the inner structure benelits from not only the anomalous dispersion characteristic of the first band-edge at the M point in the first Brillouin-zone but also zero photon states in the outer structure. A line defect waveguide is introduced in the outer structure for extracting photons from the inner cavity. Three-dimensional finite-difference time-domain simulations apparently show the in-plane laser output from the waveguide. The microcavity has an effective mode volume of about 3.2(lambda/eta(slab))(3) for oscillation -mode and the quality factor of the device including line defect waveguide is estimated to be as high as 1300.