激光硬化基体对镀铬层组织和结合的影响

采用激光相变硬化的方法在电镀前对基体表层预先进行处理，以改善镀层与基体的结合强度，提高其承载能力。借助扫描电镜（SEM）分析镀铬层的组织和界面，对镀层、相变硬化区和基体的硬度变化进行分析，对镀层抗高温烧蚀能力进行测试。结果表明，基体经激光相变硬化处理后，既可以促进镀层外延生长，又可以在镀层和基体之间实现硬度的梯度过渡，从而可以改善结合，缓解应力，提高承载能力，镀层的抗剥落能力和使用寿命得到显著提高。激光相变硬化得到细小的淬火马氏体，位错密度显著增加，表面活性增强，是促进镀层外延生长的主要原因。

Evaluation of the Interfacial Adhesion between Brittle Coating and Ductile Substrate by Cross-Secitional Indention

The cross-sectional indentation method is extended to evaluate the interfacial adhesion between brittle coating and ductile substrate. The experimental results on electroplated chromium coating/steel substrate show that the interfacial separation occurs due to the edge chipping of brittle coating. The corresponding models are established to elucidate interfacial separation processes. This work further highlights the advantages and potential of this novel indentation method.

Modeling Ammonothermal Growth of GaN Single Crystals: The Role of Transport

Single crystal gallium nitride (GaN) is an important technological material used primarily for the manufacture of blue light lasers. An important area of contemporary research is developing a viable growth technique. The ammonothermal technique is an important candidate among many others with promise of commercially viable growth rates and material quality. The GaN growth rates are a complicated function of dissolution kinetics, transport by thermal convection and crystallization kinetics. A complete modeling effort for the growth would involve modeling each of these phenomena and also the coupling between these. As a first step, the crystallization and dissolution kinetics were idealized and the growth rates as determined purely by transport were investigated. The growth rates thus obtained were termed ‘transport determined growth rates’ and in principle are the maximum growth rates that can be obtained for a given configuration of the system. Using this concept, a parametric study was conducted primarily on the geometric and the thermal boundary conditions of the system to optimize the ‘transport determined growth rate’ and determine conditions when transport might be a bottleneck.

(Ti,Al)N Film On Normalized T8 Carbon Tool Steel Prepared By Pulsed High Energy Density Plasma Technique

Under optimized operating parameters, a hard and wear resistant ( Ti,Al)N film is prepared on a normalized T8 carbon tool steel substrate by using pulsed high energy density plasma technique. Microstructure and composition of the film are analysed by x-ray diffraction, x-ray photoelectron spectroscopy, Auger electron spectroscopy and scanning electron microscopy. Hardness profile and tribological properties of the film are tested with nano-indenter and ring-on-ring wear tester, respectively. The tested results show that the microstructure of the film is dense and uniform and is mainly composed of ( Ti,Al)N and AlN hard phases. A wide transition interface exists between the film and the normalized T8 carbon tool steel substrate. Thickness of the film is about 1000 nm and mean hardness value of the film is about 26GPa. Under dry sliding wear test conditions, relative wear resistance of the ( Ti,Al)N film is approximately 9 times higher than that of the hardened T8 carbon tool steel reference sample. Meanwhile, the ( Ti,Al)N film has low and stable friction coefficient compared with the hardened T8 carbon tool steel reference sample.

On The Cyclic Bending Behaviour Of A Hard Coating On A Ductile Substrate With Periodic Surface Hardened Regions

A cyclic bending experiment is designed to investigate the interface fracture behaviour of a hard chromium coating on a ductile substrate with periodic surface hardened regions. The unique deflection pattern of the vertical cracks after they run through the coating and impinge at the interface is revealed experimentally. A simple double-layer elastic beam model is adopted to investigate the interfacial shear stresses analytically. A FE model is employed to compute the stresses of the tri-phase structure under a single round of bending, and to investigate the effect of the loading conditions on the deflection pattern of the vertical cracks at the interface. (C) 2008 Elsevier Ltd. All rights reserved.

Measurement Of Fracture Toughness And Interfacial Shear Strength Of Hard And Brittle Cr Coating On Ductile Steel Substrate

The fracture toughness and interfacial adhesion properties of a coating on its substrate are considered to be crucial intrinsic parameters determining performance and reliability of coating-substrate system. In this work, the fracture toughness and interfacial shear strength of a hard and brittle Cr coating on a normal medium carbon steel substrate were investigated by means of a tensile test. The normal medium carbon steel substrate electroplated with a hard and brittle Cr coating was quasi-statically stretched to induce an array of parallel cracks in the coating. An optical microscope was used to observe the cracking of the coating and the interfacial decohesion between the coating and the substrate during the loading. It was found that the cracking of the coating initiated at critical strain, and then the number of the cracks of the coating per unit axial distance increased with the increase in the tensile strain. At another critical strain, the number of the cracks of the coating became saturated, i.e. the number of cracks per unit axial distance became a constant after this critical strain. Based on the experiment result, the fracture toughness of the brittle coating can be determined using a mechanical model. Interestingly, even when the whole specimen fractured completely under an extreme strain of the substrate, the interfacial decohesion or buckling of the coating on its substrate was completely absent. The test result is different from that appeared in the literature though the identical test method and the brittle coating/ductile metal substrate system are taken. It was found that this difference can be attributed to an important mechanism that the Cr coating on the steel substrate has a good adhesion, and the ultimate interfacial shear strength between the Cr coating and the steel substrate has exceeded the maximum shear flow strength level of the steel substrate. This result also indicates that the maximum shear flow strength level of the ductile steel substrate can be only taken as a lower bound estimate on the ultimate shear strength of the interface. This estimation of the ultimate interfacial shear strength is consistent with the theoretical analysis and prediction presented in the literature.

Superelastic And Spring Properties Of Si3N4 Microcoils

Silicon nitride with helical structure was prepared on a large scale by CVD. On the microscale, these coiled Si3N4 ceramics still possess superelasticity and can recover their original shapes after cyclic loadings without noticeable deformations. These results suggest helical microcoils could have potential in microdevices for MEMS, motors, electromagnets, generators, and related equipment.

The induction plasma chemical reactor: Part I. Equilibrium model

A mathematical model is presented for the numerical simulation of the flow, temperature, and concentration fields in an rf plasma chemical reactor. The simulation is performed assuming chemical equilibrium. The extent of validity of this assumption is discussed. The system considered is the reaction of SiCl4 and NH3 for the production of Si3N4.

测量镀铬层界面韧性的激光屈曲法

为了测量强界面电镀铬层的界面韧性，利用连续CO_2激光器对钢基体上的电镀铬层表面进行循环扫描实验。结果表明：该种加热方式能够诱发铬层沿激光扫描方向呈周期性分布的屈曲变形。在此基础上，结合涂层屈曲变形理论，提出测量镀铬层界面韧性的激光屈曲法。该方法只需对一个屈曲单元的最大屈曲高度和屈曲半长进行测量，就可给出界面韧性。作为应用举例，利用该方法对上述镀铬层／钢基体结构界面韧性进行了测量。

测量界面软铬层力学性质的纳米压入法

为了测量双层铬的界面软铬层力学性质，提出了化学腐蚀基体法，通过溶解掉基体制备没有基体支撑的自由铬层，将在横截面内线状显示的界面转化为界面表面（铬层与基体相连接的面），避免了横截面不能显示界面表面的缺点。对界面表面进行纳米压入实验和借助于表征薄膜力学性质的表面压入能量法，测得了描述界面软铬层力学性质的弹性模量和压入弹、塑性功等参数。

镀铬/高能束复合表面处理研究进展

根据高能束对镀铬涂层及其界面强化机制的不同,镀铬/高能束表面复合技术可分为两类:高能束强化镀铬涂层复合技术和高能束预处理基体/镀铬复合技术.前者典型代表有激光表面强化或等离子体氮化/镀铬涂层;后者主要代表是激光预淬火基体/镀铬复合表面处理.综合阐述了上述3种典型的复合处理技术的原理、目的及实际综合效果;通过试验初步探讨了激光预淬火基体/镀铬复合技术延长镀铬身管寿命的主要机理.

激光淬火基体对镀铬层断裂韧性的影响

为提高30CrNi2MoVA钢镀铬身管的寿命,采用YAG激光器对钢基体进行激光搭接淬火再镀铬的复合工艺。用多裂纹拉伸技术对经激光搭接处理的30CrNi2MoVA钢再镀铬后的铬层和普通铬层的断裂韧性进行比较。结果表明,激光淬火处理基体可以提高镀铬层的断裂韧性。力学模型分析表明,基体残余压应力以抵抗基体拉伸变形的方式提高了铬层的断裂韧性;化学去基体法研究铬层界面表明,激光处理基体以细化基体影响层的晶粒形式提高了铬层的强度和韧性。离子刻蚀横截面对拉伸结果作了进一步验证。

身管内膛复合镀铬层的组织退化特征

研究了某型号身管后膛射击后复合镀铬层(由顶层的高收缩性铬和底层的低收缩性铬组成)的组织及显微硬度退化特征.结果显示:经3000发射击后,复合镀铬层沿着涂层厚度方向呈现梯度性再结晶,其组织由射击前的柱状晶粒团簇逐渐转变成等轴晶粒团簇,这导致镀铬层的硬度梯度分布;高收缩性铬层的表层晶粒成长最大,其相应的硬度由初始的960HV左右急剧下降到330HV左右.另外,高收缩性铬层许多短小的镶嵌微裂纹消失,而且一些穿透镀铬层的主裂纹形成并扩展到基体.根据服役条件下镀铬层的组织及性能退化特征,调整优化镀铬层的组织或许能有效地延长身管内膛镀铬层的寿命.

Evaluation of the Interfacial Adhesion between Brittle Coating and Ductile Substrate by Cross-Secitional Indention

The cross-sectional indentation method is extended to evaluate the interfacial adhesion between brittle coating and ductile substrate. The experimental results on electroplated chromium coating/steel substrate show that the interfacial separation occurs due to the edge chipping of brittle coating. The corresponding models are established to elucidate interfacial separation processes. This work further highlights the advantages and potential of this novel indentation method

A special method to evaluate the strong adhesion between brittle coating and ductile substrate

The evaluation of the interfacial adhesion of coating system has always been a rough task. In this paper, a special testing method of cross-sectional indentation is applied on a model coating system, i.e. electroplated chromium on a steel substrate which is generally regarded as an example of materials pair with strong adhesion. Based on fractography analysis with SEM and interfacial stress simulation with FEM, it is found that interfacial shear stress may induce coating spalling. More interestingly, spalling location is sensitive to substrate pretreatment process. This shows the feasibility of cross-sectional indentation to distinguish interfacial strength at a high level.