U-transformation-finite element method in 3-dimensional analysis of orthotropic laminates

For an orthotropic laminate, an equivalent system with doubly cyclic periodicity is introduced. Then a 3-dimensional finite element model for the equivalent system is transformed into the unitary space, where the large finite element matrix equation is decoupled into some small matrix equations. Such a decoupling very efficiently reduces the computational effort. For an orthotropic laminate with four clamped edges, no exact elasticity solution is available, and the deflection values predicted by different methods have a considerable difference each other for a small length-to-thickness ratio. The present predictions are the largest because the present method is a full 3-dimensional finite element analysis without superfluous constraints. Illustrative numerical examples are presented to observe the distributions of stresses through the thickness of the laminates. (C) 2010 Elsevier Ltd. All rights reserved.

LOCAL BENDING OF THIN FILM ON VISCOUS LAYER

Effects of deposition layer position and number/density on local bending of a thin film are systematically investigated. Because the deposition layer interacts with the thin film at the interface and there is an offset between the thin film neutral surface and the interface, the deposition layer generates not only axial stress but also bending moment. The bending moment induces an instant out-of-plane deflection of the thin film, which may or may not cause the so-called local bending. The deposition layer is modeled as a local stressor, whose location and density are demonstrated to be vital to the occurrence of local bending. The thin film rests on a viscous layer, which is governed by the Navier-Stokes equation and behaves like an elastic foundation to exert transverse forces on the thin film. The unknown feature of the axial constraint force makes the governing equation highly nonlinear even for the small deflection case. The constraint force and film transverse deflection are solved iteratively through the governing equation and the displacement constraint equation of immovable edges. This research shows that in some special cases, the deposition density increase does not necessarily reduce the local bending. By comparing the thin film deflections of different deposition numbers and positions, we also present the guideline of strengthening or suppressing the local bending.

支承弹簧对输液曲管固有频率和极限流速的影响

基于Hamilton变分原理,导出具有弹性支撑的1/4圆形输液曲管的变分—积分方程.采用多个函数组合的方法,选取满足边界条件的试函数,利用Galerkin直接法求出系统的固有频率和极限流速的近似解析公式.数值结果表明,弹簧对固有频率和极限流速都有显著影响.根据数值结果,用最小二乘法给出固有频率和极限流速与弹簧刚度的关系公式

青藏高原东部混农季节性放牧及其对高山林线格局的影响

混农季节性放牧（agropastoral transhumance）通过作物种植和畜牧生产相结合的方式对不同海拔高度带上的资源进行相互补充利用，在亚洲兴都库什地区、青藏高原、横断山、东部及南部非洲、南美安第斯地区等具有悠久的历史。这种传统的生计系统几千年以来一直是居住在该地区的人类社会和自然生态系统相互作用的主要形式之一。这种传统的资源利用方式与山地自然植被以及特殊的山地人类文化和社会特征具有密切的协同演变关系。认识和理解这一关系，是山地生态学和人类学的核心科学问题之一。近年来，山地生态系统的多重功能性及动态演变对山区社会经济可持续发展的重要意义受到人们的不断关注。本文通过对云南省德钦县的12个自然村的混农季节性放牧以及对云南德钦、四川壤塘等山地植被格局特别是高海拔地带植被格局的的详细调查，探讨青藏高原东缘地区混农季节性放牧的主要特征、系统构成及相互关系，及其在全球变化、经济全球化和市场化及现代化过程中的变化趋势，分析混农季节性放牧与高山林线格局及生态系统的互动关系，旨在探讨山地地区人类活动与自然生态系统之间的互动关系，从而为山区社会经济可持续发展、环境建设和生物多样性保护等国家战略提供理论依据。 调查结果表明，混农季节性放牧是一种适应青藏高原东部高山峡谷地区环境因子及自然资源呈明显的垂直分布、资源数量稀少而时空分布异质性极高的生存环境的一种传统经济形式。这种传统的畜牧业的主要生产目的仍然是提供当地基本生存所需的产品，饲养牲口的种类和数量取决于农户的当地需求并且受资源的限制，因而维持在比较低的水平的。分布在不同海拔高度的放牧资源在一年中被牲口利用的时间也不同，互为补充，共同构成混农季节性放牧的资源基础。根据各社区永久居住点的位置和该村的土地资源特别是牧草地资源的分布范围，牲口迁移的距离和格局有较大的差异。。天然牧场仍然是最主要的畜牧业生产资源。混农季节性放牧中的农业系统和牧业系统互为补充，共同构成调查地区完整的的生计系统，农耕活动为放牧活动提供精饲料如粮食等和冬季饲料如秸秆， 其数量往往成为家庭畜牧业生产规模的主要决定因子之一。 通过对牲口数量和结构、牲口的时空迁移格局、牧业活动在整个经济活动中的相对重要性以及牧业活动和作物种植的关系方面的研究分析，混农季节性放牧在近几十年发生了深刻的变化。主要表现在牲口数量总体下降，牲口组成发生变化，牲口移动性降低、牧业活动的经济重要性下降以及牧业活动和种植活动之间的相互依存度降低等。上述变化的根本驱动力是发生在当地、地区及全球尺度上的环境、政治、社会经济、技术和文化等的变化，从而造成当地群众畜牧生产目标、土地利用和劳动力的分布等发生了变化。当地生计系统发生的改变可能会带来对方面而深刻的政治、社会经济、文化和生态影响。 混农季节性放牧这种古老的传统生计策略面临着许多挑战，如冬季饲料短缺、草场退化、缺乏市场竞争力、经济重要性降低、对年轻人缺乏吸引力、国家缺乏专门的政策指导等。与此同时，经济全球化、市场经济、新技术的应用、替代生计机会的增加、国家对于山地生态系统的作用的重新定位等也为传统生计系统转型、实现社会与生态共赢创造了机遇。 混农季节性放牧活动对亚高山及树线交错带生态系统系统的互动方式主要体现在以下几个方面：（1）牲口啃食、践踏等影响森林群落更新，改变森林群落的组成和结构，从而影响森林群落的演替进程和植被格局。林线边缘是搭建夏棚的首选地点，因此林线及树线交错地带就成了牲口活动的主要场所之一；（2）利用火烧开辟、维持和改良高山牧场； 3）在亚高山火灾迹地的放牧活动能够阻止火烧迹地的顺向演替； 4）牧民在林线附近获取建材和薪材等活动影响高山林线附近森林的结构和功能。 在调查区域，梅里雪山、白马雪山、甲午雪山的林线海拔高度在4200-4300m之间； 四川雅江、理塘一线，林线位置多在4300-4400m；四川壤塘二林场一带的林线主体在4100-4200m，在个别地区达到4300m； 在贡嘎山的南坡和东坡一带，林线位置在3600-3700m；而在四川松潘一带，林线位置主体在3700-3800米左右。树线高度的分布趋势和林线一致。混农季节性放牧及其有关人类利用活动使研究地区很多地方高山林线降低、树线交错带宽变窄或消失。在研究地区，总体情况是，阳坡和半阳坡（南坡、西南坡等）的林线和树线比阴坡和半阴坡（北坡、东北坡等）低，变化幅度达20-200m。这种差异主要是为了开辟牧场而人为清除了南向坡自然林线及其以上的植被从而使林线位置下降所致。在南坡自然林线保留得比较好的地方，林线和树线依然可以达到甚至超过北坡林线和树线的高度。放牧活动抑制了高山林线带火烧迹地的天然更新，从而使林线位置保持在目前的位置。 放牧活动对高山林线带森林群落更新的影响是显著的。自然林线内的乔木个体密度特别是新生苗和幼苗的密度大大高于非自然林线。没有放牧的自然林线及树线交错带内的I级个体（新生苗）密度达到725-2917株/公顷，而与之相对的处理样地内I级个体的密度只有0-228株/公顷；II级个体（高度10-50cm）也表现出类似的趋势，在没有放牧的自然林线及树线交错带样方内，其密度达到550-5208株/，而在放牧处理样方内只有14-321株/公顷。在非自然林线带样地内，在有正常放牧的样地内，完全缺乏I级个体。 从相对比例来看，没有放牧的样方内的I、II级个体在全部个体中所占的比例显著高于有放牧活动的样方。放牧使林线交错带的乔木幼苗数量显著减少，从而影响林线及树线交错带森林群落的天然更新过程。林线和树线交错带的灌木对乔木幼苗具有重要的保护作用，能够为树线树种如冷杉等幼苗的定居体提供有利的微气候环境，同时保护苗免受牲口的啃食和践踏。火烧以后接着进行放牧能够100%地抑制高山林线带的幼苗更新。 高山牧场放牧强度降低、使用时间缩短而低海拔地带放牧强度增加是研究地区混农季节性放牧系统的一个显著变化。这种变化也必然会引起各海拔带上的生态系统的变化。放牧强度的降低、生产性用火的停止将导致原来通过人工火烧而降低并通过进一步的火烧和放牧活动来维持的林线及其以上地带的灌木盖度和高度的增加，从而为林线森林群落的扩张创造条件。 青藏高原东部高山峡谷地区是我国重要的山地生态系统，在我国的生物多样性保护、生态环境建设、社会经济可持续发展战略中具有举足轻重的作用。正确认识人类特别是当地传统的生计系统与生态环境系统的互动关系是实现上述战略目标的前提。决策者必须以综合、系统的的视角协调促进社会经济可持续发展、保护生物及文化多样性和维持人、牲口和生态系统之间的平衡的多重目标。 Agropastoral transhumance, which makes a complementary exploitation of the natural resources at different altitudinal belts through a combination of migratory animal husbandry and crop cultivation, has a long history in Hindu-Kush Himalaya, Tibet Plateau, Hengduan Ranges, eastern and southern Africa and the Andes region of south America.For millennia, this traditional livelihood strategy has been one of the main forms of interaction between human societies inhabiting in these regions and their natural ecocystems. A close co-evolutionary relationship has been developed between this indigenous resources management systems and the mountain vegetation systems on the one hand and a unique set of cultural values and social features on the other. Understanding this relationship has been one of the core scientific issues in mountain ecology and anthropology. In recent years, the importance of the multiple functions of the mountain ecosystems and their dynamic changes in the sustainable socio-economic development of the mountain regions has gained increasing attention. This paper, which is based on a detailed study on the agropastoral practices of the 12 natural villages in Deqin County of Yunnan, and the mountainnn vegetation patterns in Deqin of Yunnan and Rangtang County of Sichuan, intends to reveal the major characteristics, system composition and the inter-relations of the subsystems of the agropastoral transhumance in Eastern Tibetan Plateau as well as the trends of changes of the system within the context of global changes, economic globalization and modernity process of China and analyze the relations between agropastoral transhumance and alpine ecosystem, ao as to understand the interactions between human activities and natural ecosystems of the mountains and provide theoretical basis for the national strategies in eocioeconomic development, environmental reconstruction and biodiversity conservation in the mountain regions. Results of the survey indicate that agropastoral transhumance in the investigated area is a traditional economic form that is highly adapted to the eastern Tibet Plateau where the topography features high peaks and deep gorges and where the highly variable environmental parameters and scanty natural resources exhibit a distinct vertical spectrum of distribution and great temporal and spatial heterogeneity. The main objective of pastoral management is still aimed at the production of basic goods and services of local people and thus the type and size of animals raised for each household mainly depend on local needs and are limited by the availability of natural resources. The scale of production is relatively low. Pastoral resources at different altidudinal belts are complementarily used at different seasons of a year and thus form the resources basis for agropastoral production of the study area. Migration distances and patterns vary with the location of the permanent settlements, the elevational distribution range of the resources of the villages concerned. Natural pastures (rangelands) are the main fodder resources and sumplement feedings only account for less than 5% of the total fodder consumption. Crop cultivation and pastoral activities support each other to form a complete livelihood system. The ability of the farmig lands (crop cultivation) to provide the pastoral activities with concentrates and sumplements often becomes a main factor limiting the scale of livestock production at household level. Agropastoral transhumance is experiencing drastic changes in recent decades as is reflected in the size and composition of animals, the seasonal migration pattern, the relative importance of pastoralism in the household economy and the interplays of agricultural and pastoral elements of the system. In general, there is a decline in animal population and mobility, a shift in animal composition to meet new needs arising from changed macro-economic situation, a decrease in the relative importance in the household economy and an increasing decoupling of agro&pastoral relations. The fundamental divers of these changes can be traced to environmental, social, economic, technological and cultural changes from local to global levels and such changes have further caused local changes in livestock management objectives, land use and distribution of labor forces. Changes in local livelihood systems could have profound political, socioeconomic, cultural and ecological conseuquences. Agropastoral transhumance, as an age-old traditional livelihood strategy, is facing multifacet challenges, such as winter fodder shortage, rangeland degradation, lack of market competitiveness, decrease in economic importance, lack of appreciation among the young generation and adequate policies from the government. At the same time, economic globalization, market economy, intrdoctution of new technologies, increase of alternative income generating opportunities and the national re-oreitation of policies on mountain ecosystems have all brought about new opportunities for the transformation of the traditional livelihood system and the synchronized development of local society and the environment. Agropastoral transhumance interacts with the ecosystems at the timberline and treeline ecotone mainly through the following aspects: 1)Animal browsing and stamping affect the regeneration process of the forest communities and alters the composition and structure of the forest which in turn affect the succession process and vegetation pattern of the forest communities. Forest edges are the priority locations for summer houses and therefore the timeline and treeline area becomes the major venues of aninal activities; （2）herders create, maintain and improve pastures through burning that remove the forest communities at the timeline and treeline ecotone; 3）immediate grazing on the fire sites can significantly prevent the fire sites from perogressive succession; and 4）herders harvesting of construction timber and firewoods affects the structure and functions of the forest communities at the timberline and treeline zone. Timberline position in the survey region shows geographical variations. It is around 4200-4300m in Meilixueshan, Baimaxueshan and Jiawuxueshan in Northwest of Yunnan and rises to 4300-4400m in Yajiang County and Litang County of Sichuan. In Rangtang of Sichuan, it is between 4100-4200m, though reaching 4300m in localized sites. In the southern and eastern slopes of Gongga Mountain, the timberline is only between 3600m and 3700m and in Songpan County at the upper reach of the Minjiang River the timberline is around 3700-3800m.Treeline pattern follows similar trend. In many places, agropastoral transhumance and related human activities have lowered the timberline and treeline and narrowed or removed the treeline ecotone. In the area of survey, generally speaking, timberlines and treelines are lower on the southern slopes than on the northern slopes, with a difference between 20 and 200m. This is mainly because that the use of fires to crerate pastures has removed the forest vegetation at the previous timberline and above. In fact, in many places, well-preserved forests on the south slopes have even high timberline position that the corresponding northern slopes. At subalpine zone, grazing activities could have prohibited the natural regeneration of many forest fire sites and maintained the forest position at the present level. Grazing has a significant impact on the regernation process of forest communities at the timberline zone. Natural timberline and treeline ecotone has much higher density of treeline species individuals especially the emergents and seedlings than the timberlines that are maintained by human activities. In natural timberline and treelien ecotone without grazing interference, the density of the I Class seedlings (less than 10cm in height) ranges 725-2917 /hm2; while that in the treatment plots (with grazing disturbance) is only 0-228//hm2；II Class seedlings (10-50cm）exhibit similar density trends, reaching 550-5208//hm2 in natural timberline without grazing but only 14-321//hm2 in the plots with grazing treatment. In the man-created timberlines, there is no I Class seedling at all in plots with normal grazing activities. In relative terms, in plots without grazing activities, the propotion of I Class and II Class seedlings is much higher than that in plots with grazing. Grazing activities have significantly reduced the number of seedlings in the timberline ane treeline ecotone, and thus affect the natural regeneration process of the forests. Shrubs at the timberline and treeline ecotone can effectively protect the seedlings from severe climate and animal tramping, thus increasing the survival rate of the seedlings. Grazing following fires can completely inhibit forest regeneration process at timberline. Changes in agropastoral transhumance will have great impact on the timberline and treeline pattern of the studied area. The decrease in grazing intensity on alpine pastrues and the cessation of the use of fires will result an increase in the cover and height of shrubs above the present human-maintained treeline, which will create further condition for the expansion of timberline forest communities. Eastern Tibet Plateau harbors some most important mountain ecosystems of China that are of vital importance to the country’s strategy in biodiversity conservation, environmental construction and sustainable sociaoeconomic development. A proper knowledge of the interactions between traditional livelihood systems and the ecosystems in the region is a precondition to the realization of the above strategic goals. Therefore, the decision-makers must have a holistic and systemic perspective so as to integrate the multiple objectives of promoting sustainable socioeconomic development, conserving biological and cultural diversity and maintaining the balances among people, animal population and the ecosystems.

香港地区湍蛙遗传多样性研究

依据线粒体上ND2和CO1两个变异较大的基因序列分析了香港地区香港湍蛙7种群、华南湍蛙1种群，以及大陆其他地区华南湍蛙7种群，戴云湍蛙1种群，武夷湍蛙1种群的系统发育关系，进而探讨香港湍蛙的遗传多样性、香港湍蛙特有性、如何确定香港湍蛙最佳保护单元以及这四种湍蛙的物种分类地位。 1． 香港湍蛙保护遗传学研究 香港湍蛙核苷酸传多样性较低，从其遗传多样性信息、单倍型网络分析、中性检验值以及岐点分布结果一致显示香港湍蛙很可能经历了瓶颈后的扩张，种群正在由一个较小的有效种群大小迅速增长, 有足够的时间通过变异用于积累单倍型的多态性, 而对于提高核苷酸多样化而言, 时间尚短（Nei M et al，1975，Avise J C，2000；李明等，2003）。 分子变异分析结果显示香港湍蛙种群间存在较多的基因交流，且系统发育树上各种群间交叉在一起，没有形成与地理单元相关的分支，而从其单倍型网络看，他们源于共同的祖先，是一个单系群，与地理单元间没有形成显著的遗传分化。因此应作为一个进化显著单元（ESU）。结合其与其他湍蛙发育关系及遗传距离以及野外采集信息认为香港湍蛙只在香港地区有分布，属于香港特有种。该物种内遗传多样性较低，又属于世界自然保护联盟红皮书中的近危种，同时也是《野生动物保护条例》中的受保护野生动物，且由于香港城市建设等使得其栖息环境受到威胁，因此在香港特别行政区应该受到重点保护。 从单倍型分布和核苷酸多样性可以看出大榄涌种群和城门种群具有较高的单倍型多样性和核苷酸多样性，应该作为保护的重点区域。 2. 华南湍蛙东、南沿海种群间系统关系 华南湍蛙分布广，各种群存在着丰富的遗传多样性信息且中部种群广西龙胜和湖南张家界种群核苷酸多样性明显高于其他边缘种群华南湍蛙。种群间几乎没有基因交流，且各种群间无共享单倍型，可见已形成了显著的遗传分化。各种群间遗传距离都较远，其中广东南昆山种群以及福建三港种群与其他种群距离最远，因此可以推测其他种群（广东深圳、香港大屿山、广西龙胜和防城以及湖南张家界种群）可能为独立进化的种群。但是否是一新种或一隐存种，还需要结合形态学进行更深入的研究。 本研究中无论从系统关系看还是从遗传距离看，大屿山种群与深圳种群最近，支持陈坚峰等将其定为华南湍蛙，即华南湍蛙新增一个分布点：香港大屿山。 系统树上广西防城种群（支B）与龙胜和湖南种群（支A）形成姐妹群。香港大屿山种群与深圳种群先形成姐妹群（支C），但却没有与其距离很近的广东南岭及南昆山种群（支D）形成姐妹群，可能粤北和粤中的环境及气候较复杂因此与粤南其他种群形成了明显的隔离。同时可以看出华南湍蛙种群遗传分化与地理距离没有显著的相关性。 3. 四种湍蛙间的系统关系 根据线粒体CO1基因建立四种湍蛙间的系统关系及其遗传距离，很清楚地看到，香港湍蛙与戴云湍蛙关系很近，而华南湍蛙则与武夷湍蛙较近。然而，戴云湍蛙同一个种群内部共有两个单倍型DY1和DY2，且两个单倍型间遗传距离大于DY1与香港湍蛙间遗传距离，更远远大于香港湍蛙种群内部的距离，即戴云湍蛙内部两个单倍型间遗传距离达到了种级水平，同样在系统发育树上这两个单倍型与香港湍蛙形成并系。但是，戴云湍蛙种内在形态上差异不显著。因此，其是否属于萌芽物种分化形成（budding speciation）或已经完全分化为两个不同的种值得进一步研究？ 与戴云湍蛙香港湍蛙关系类似，从系统树上看华南湍蛙不形成单系，而是分成两个大支，与武夷湍蛙形成并系，且福建和南昆山的华南湍蛙与武夷湍蛙遗传距离远大于武夷湍蛙种内福建种群与浙江种群的遗传距离，达到了种级分化水平。由此，可以推断武夷湍蛙是有效种。系统树上广东深圳、香港大屿山、广西防城和龙胜以及湖南张家界种群与华南湍蛙福建及南昆山各种群间遗传距离已超出了种内各种群间的遗传距离，但是至于这一支是否应为另外一个种，有必要扩大采样，并结合核基因及形态信息进行进一步研究。 MtDNA of ND2 and CO1 gene were used to investigate genetic diversity of Amolops in Hongkong .We collected seven populations of A. hongkongensis,，one population of A.ricketti from Hong Kong and other seven populations of A.ricketti from East and South of Chinese mainland. As well as one population of A. daiyunensis and one population of A.wuyiensis Phylogenetic relationship were analyzed of four species. Discussed whether A.hongkongensis is an endemic species and how can we make the conservation and management decisions. 1. Conservation Genetics of A. hongkongensis A. hongkongensis has a low nucleotide diversity, the results of genetic diversity, haplotype network, neutrality test and the mismatch distributions indicate that A. hongkongensis experienced a recent expansion after a bottle neck. They had enough time to accumulated haplotype diversity, but it’s too short to have a high nucleotide diversity（Nei M et al，1975，Avise J C，2000；Li et al，2003）. The result of AMOVA reveals that it has much gene exchange among the populations of A. hongkongensis. The clades of the phylogenetic tree were mixed together, no significant genetic differentiation among 8 populations and they share the same ancestor from the network analysis, these indicate that they are monophyly and should be protected as one ESU. Combined with the information of relationships of interspecies, genetic distance and distribution investigate, We conclude that A. hongkongensis is an endemic species of Hong Kong. Considering on the status of low genetic diversity in A.hongkongensis, and this species was listed in the IUCN red list as near threatened, as well as listed in the . Furthermore, it’s habitat loss and degradation more rapidly as the human activity got higher and higher. So it’s urgent to protect them in Hong Kong. Our results suggest that Tai Lam Wu and TAI MO Shan -Shing Mun populations have the higher priority to be protected because their higher genetic diversity. 2．Phylogenetic relationships among populations of Amolops ricketti from the Southern and eastern China A. ricketti has the considerable genetic diversity of mitochondrial haplotypes within and among populations, and Mitochondrial DNA diversity was higher in populations at the central area of the present distribution range of the frog，i. e. the Longsheng population and Zhangjiajie population, than at the edges of their distribution range. They have no share haplotype among populations, and have a significant genetic differentiation. Genetic distance is high among the populations, especially the distance of Nankun and Sangang group with others, which suggested that they evolved independently. May be there is a cryptic species or a new species, a further study is needed. The results of gene tree and the genetic distance clearly demonstrate that the population from LanTau island is A. ricketti, so we agree with Chen et al(2005) . That means A.ricketti have a new distribution site: LanTau island, HongKong. Phylogenetic relationships were analyzed through NJ and Mrbayes methods and got a consistent topological structure, the structure indicated that the ingroup were comprised four groups. Populations Longsheng and Zhangjiajie were first clustered as clade A; Populations Fangcheng was clustered together (clade B) as a sister group to clade A；Populations Shenzhen and Lantau island were sister groups and clustered as clade C；Then the clade D included populations Nankunshan and Nanling in Guangdong province and Sangang in Fujian province. 3. Phylogenetic Relationships among these four specises Phylogenetic relationships based on 1503bp CO1 gene and the genetic distance show that A. hongkongensis close to A. daiyunensis whereas A.ricketti near to A.wuyiensis. Nevertheless, there are two haplotypes in A.daiyunensis and the genetic distance between them higher than the distance between DY1 with A. hongkongensis. A. hongkongensis is nested in the paraphyletic ancestral species A. daiyunensis. Without significant difference in the morphological characters, So, we considered both A.daiyunensis and A.hongkongensis are valid species, may be this represents a case of ‘budding speciation’ like Batrachuperus pinchonii(Fu and Zeng,2008) in the population of A. daiyunensis. Just like two species above A. wuyiensis and A. ricketti are not monophyly, instead, A.wuyiensis is nested in the paraphyletic ancestral species A.ricketti. We need do more research to make sure whether they are new species.

Preparation and characterization of CdS nanotubes and nanowires by electrochemical synthesis in ion-track templates

CdS nanotubes and nanowires have been synthesized with controlled dimensions by means of template-electrodeposition method in etched ion-track membranes. The diameters of nanotubes and nanowires are between 20 and I 10 nm, and the lengths are up to tens of micrometers. X-ray diffraction (XRD) and selected area electron diffraction (SAED) pattern investigations demonstrate that CdS nanotubes and nanowires are polycrystalline in nature. The UV-vis absorption spectra of CdS nanotubes and nanowires embedded in polycarbonate (PC) membranes show that the absorption edges of PC films shift towards the shorter wavelength, with decreasing diameters of the deposited nanostructures. The results indicate that nanowires are formed from nanotubes by nanotube-stuffing-growth mechanism.

生态边缘效应与生态平衡变化方向

Human activities produce inany ecosystems which form new edges with original ones.On the other hand, the edge effects also change the quality of ecosystems. The new edge effects will show positive or negative ecological effect on the original ecosystems, which is named as edge effect directivity.Therefoe that human activities can affect the change directions of ecosystem quality with edge effects. It is important to study to the edge effect and the change direction of ecosystem balance,so as to regulate and control the ecosystems wisely.

Enhancements of the simulation method on the edge effect in resin transfer molding processes

In resin transfer molding processes, small clearances exist between the fiber preform and the mold edges, which result in a preferential resin flow in the edge channel and then disrupt the flow patterns during the mold filling stage. A mathematical model including the effect of cavity thickness on resin flow was developed for flow behavior involving the interface between an edge channel and a porous medium. According to the mathematical analysis of momentum equations in a fully developed rectangular duct and formulations of the equivalent edge permeability, comparing with three-dimensional Navier-Stokes equations, the governing equations were modified in the edge channel. The volume of fluid (VOF) method was applied to track the flow front. A simple case is numerically simulated using the modified governing equations. The effects of edge channel width and cavity thickness on flow front and inlet pressure are analyzed, and the evolution characteristics of simulated results are in agreement with the experimental results. (c) 2007 Elsevier B.V. All rights reserved

Nanostructured bulk novel hard material with "rounded" grains obtained by nanocrystalline "rounded" (W0.5Al0.5)C powders

A novel nano-scaled bulk hard material (W0.5Al0.5)C-Co with "rounded" grains was prepared by nanocrystalline "rounded" (W0.5Al0.5)C powders with "rounded" particle shape in this study. The nano-scaled "rounded" particles do not contain sharp edges, which form local tensile stress concentrations on loading of the composite, thus leading to improved toughness and reduced sensitivity to crack. Nanocrystalline (W0.5Al0.5)C powders with "rounded" particle shape were used as starting materials. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used to characterize the samples.

Micropatterning of polymeric semiconductor by selective lift-off method using epoxy mold

A simple and efficient method for patterning polymeric semiconductors for applications in the field of organic electronics is proposed. The entire polymer layer, except for the desired pattern, is selectively lifted off from a flat poly(dimethylsiloxane) (PDMS) stamp surface by an epoxy mold with a relief pattern. This is advantageous because the elastic deformation of the PDMS stamp around protrusions of a patterned stamp under pressure can assist the plastic deformation of a polymer film along the pattern edges, yielding large area and high quality patterns, and the PDMS surface has low surface energy, which allows the easy removal of the polymer film.

Synthesis, structure and photochromic properties of a novel 1,6-hexanediamine trimolybdate supramolecular compound

A novel supramolecular compound 1,6-hexanediamine trimolybdate ((C6H18N2[Mo3O10], denoted as HDAMo) has been synthesized by a hydrothermal method and its structure has been characterized by elemental analyses, Fourier transform infrared (FT-IR) spectra, single-crystal X-ray diffraction (XRD) technique. This single crystal compound consists of protonated 1,6-hexanediamine (HDA) cations and polyoxometalate [Mo3O10](2-) anions. Its crystal structure belongs to monoclinic system (space group P2(1)/n) with a = 7.7508(14), b = 11.467(2), c = 16.167(3) angstrom, beta = 92.689(3)degrees, V = 143 5.3(5) angstrom(3), Z = 4 and D-ealc = 2.619 g cm(-3). The final statistics based on F-2 are GOF = 0.980, R-1 = 0.0261 and wR(2) = 0.0506 for I > 2 sigma(I). XRD analysis revealed that in the crystal structure of HDAMo, novel infinite [Mo3O10](2-) chains parallel to a axis are made up of distorted MoO6 octahedra connected by corners and edges. The protonated HDA cations occupy channels formed by [Mo(3)O3(10)](2-) Chains and exhibit strong hydrogen bond interactions to terminal and bridging oxo groups of the chains. The [Mo3O10](2-) chains linked through protonated HAD cations formed a one-dimensional network. The HDAMo compound shows novel photochromic properties, i.e., its color changes from white to reddish brown gradually under UV irradiation. XRD, FT-IR, ESR spectra and XPS are used to investigate the photochromic behavior of the compound.

Effect of cerium on microstructure and electrochemical performance of Ti-V-Cr-Ni electrode alloy

Effect of cerium on the microstructure and electrochemical performance of the Ti0.25V0.35-xCexCr0.1Ni0.3 (x = 0, 0.005) electrode alloy was investigated by X-ray diffraction (XRD), field emission scanning electron microscopy/energy dispersive X-ray spectrometry (FESEM-EDS), and electrochemical impedance spectroscopy (EIS) measurements. On the basis of XRD and FESEM-EDS analysis, the alloy was mainly composed of V-based solid solution with body-centered-cubic structure and TiNi-based secondary phase. Ce did not exist in two phases, instead, it existed as Ce-rich small white particles, with irregular edges, distributed near the grain boundaries of the V-based solid solution phase. Discharge capacity, cycle stability, and high-rate discharge ability of the alloy electrode were effectively improved with the addition of Ce at 293 K. It was very surprising that the charge retention was abnormal with larger discharge capacity after standing at the open circuit for 24 h. EIS indicated that addition of Ce improved the dynamic performance, which caused the charge transfer resistance (R-T) to decrease and exchange current density (I-0) to increase markedly. The exchange current density of the electrochemical reaction on the alloy surface with Ce addition was about 2.07 and 3.10 times larger than that of the alloy without Ce at 303 and 343 K, respectively.

In situ synthesis of silica gel nanowire/Na+-montmorillonite nanocomposites by the sol-gel route

Silica-gel nanowire/Na+-montmorillonite (Na+-MMT) nanocomposites were prepared by the in situ sol-gel process of tetraethyl orthosilicate (TEOS) in the presence of Na+-MMT and ammonia as catalyst. Microstructure characterization of the nanocomposites was done by SEM, , EDX, XRD and FTIR. It was found that a lot of silica-gel nanowires grew along the edges of Na+-MMT. The combination between the nanowires and Na+-MMT was accomplished via polycondensation of the hydrolyzed TEOS and the edge-OH groups of Na+-MMT.

Micropatterning of metal films coated on polymer surfaces with epoxy mold and its application to organic field effect transistor fabrication

In this letter, a simple and versatile approach to micropatterning a metal film, which is evaporated on a Si substrate coated with polymer, is demonstrated by the use of a prepatterned epoxy mold. The polymer interlayer between the metal and the Si substrate is found important for the high quality pattern. When the metal-polymer-Si sandwich structure is heated with the temperature below T-m but above T-g of the polymer, the plastic deformation of the polymer film occurs under sufficiently high pressure applied. It causes the metal to crack locally or weaken along the pattern edges. Further heating while applying a lower pressure results in the formation of an intimate junction between the epoxy stamp and the metal film. Under these conditions the epoxy cures further, ensuring adhesion between the stamp and the film. The lift-off process works because the adhesion between the epoxy and the metal film is stronger than that between the metal film and the polymer. A polymer field effect transistor is fabricated in order to demonstrate potential applications of this micropatterning approach.

Hydrothermal synthesis, structure, and characterization of two one-dimensional chainlike hybrid complexes [(CuX)(2)(o-phen)](infinity) (X = Br, Cl; o-phen = o-phenanthroline)

Two novel organic-inorganic hybrid complexes [(CuX)(2)(o-phen)](infinity) (X = Br (1), Cl (2); o-phen = o-phenanthroline) have been synthesized hydrothermally and characterized structurally by elemental analyses, IR, ESR, XPS spectrum, TG analyses and single-crystal X-ray diffraction. Both title compounds exhibit novel one-dimensional chainlike copper halide scaffolding constructed by the unusual [Cu3X3] hexagon motifs by sharing opposite edges, where a single Cu site of each [Cu3X3] hexagon is chelated with N donors of o-phen group. To our knowledge, such basic o-phen-copper halide skeleton has not been reported hitherto. Moreover, TG analyses indicate that both title compounds possess high thermal stability.