K418与42CrMo异种金属的激光穿透焊接

实验研究了连续波Nd：YAG激光焊接速度、侧吹保护气流量和离焦量等参量对激光穿透焊接K418和42CrMo焊缝成形的影响。结果表明，K418与42CrMo激光穿透焊接有X形和T形两种典型的焊缝形貌，且焊缝形貌是不对称的。随着焊接速度的提高，焊接线能量降低，焊缝尺寸变小，且焊缝上部尺寸变化比下部尺寸变化慢，焊缝形貌由X形过渡到T形。当离焦量在瑞利长度范围内时，焊缝正面宽度变化很小；当离焦量超出瑞利长度范围时，在足够高的激光功率密度下，焊缝正面宽度快速增加。在激光功率为3kW，侧吹保护气角度为35°条件下，通过优化焊接速度、侧吹保护气流量和离焦量等参量可以得到最佳焊缝质量。

Nonequilibrium microstructures and phase evolutions of an iron-based laser clad coating

The microstructural and compositional features of the laser-solidified microstructures and phase evolutions occurring during high temperature tempering were investigated by using analytical electron microscopy with energy dispersive X-ray analysis. The cladded alloy, a powder mixture of Fe, Cr, W, Ni and C with a weight ratio of 10:5:1:1:1, was processed with a 3 kW continuous wave CO2 laser. The cladded coating possessed the hypoeutectic microstructure of the primary dendritic gamma-austenite and interdendritic eutectic consisting of (gamma+M7C3). The gamma-austenite is a nonequilibrium phase with extended solid solution of alloying elements. And, a great deal of fine structures, i.e., a high density of dislocations, twins, and stacking faults existed in austenite phase. During high temperature aging, the precipitation of M23C6, MC and M2C in austenite and in situ transformation of M7C3(+gamma) --> M23C6 and M7C3+gamma --> M6C occurred. The laser clad coating revealed an evident secondary hardening and superior impact wear resistance.

Rapidly solidified nonequilibrium microstructure and phase transformation of laser-synthesized iron-based alloy coating

The rapidly solidified microstructural and compositional features, the precipitation and transformation of carbides during tempering, and the impact wear resistance of an iron-based alloy coating prepared by laser cladding are investigated. The clad coating alloy, a powder mixture of Fe, Cr, W, Ni, and C with a weight ratio of 10:5:1.1.1, is processed using a continuous wave CO, laser. Microstructural studies demonstrate that the coating possesses the hypoeutectic microstructure comprising the primary dendritic gamma-austenite and interdendritic eutectic consisting of gamma-austenite and M7C3 carbides. gamma-Austenite is a non-equilibrium phase with an extended solid solution of alloying elements. During high temperature tempering at 963 K for 1 h, the precipitation of M23C6, MC and M2C carbides in austenite and in situ carbide transformation of M7C3 to M23C6 and M7C3 to M6C respectively are observed. In addition, the microstructure of the laser-clad coating reveals an evident secondary hardening and a superior impact wear resistance.

Near-diffraction-limited, 35.4 W laser-diode end-pumped Nd:YVO4 slab laser operating at 1342 nm

A diode stack end-pumped Nd:YVO4 slab laser at 1342 nm with near-diffraction-limited beam quality by using a hybrid resonator was presented. At a pump power of 139.5 W, laser power of 35.4 W was obtained with a conversion efficiency of 25.4% of the laser diode to laser output. The beam quality M-2 factors were measured to be 1.2 in the unstable direction and 1.3 in the stable direction at the output power of 29 W. (C) 2009 Optical Society of America

Two mechanisms for population inversion via two-colour coherent excitation in three-level systems

We analyse the physical origin of population inversion via continuous wave two-colour coherent excitation in three-level systems by dressing the inverted transition. Two different mechanisms are identified as being responsible for the population inversion. For V-configured systems and cascade (E) configured systems with inversion on the lower transition, the responsible mechanism is the selective trapping of dressed states, and the population inversion approaches the ideal value of 1. For Lambda-configured systems and Xi-configured systems with inversion on the upper transition, population inversion is based on the selective excitation of dressed states, with the population inversion tending towards 0.5. As the essential difference between these two mechanisms, the selective trapping of dressed states occurs in systems with strong decay into dressed states while the selective excitation appears in systems with strong decay out of dressed states.

Investigation of transient process and steady output of lasing without inversion

The transient evolution processes and steady outputs of continuous wave lasing without inversion (LWI) and self-pulsing LWI in a resonant open V type three-level system are studied. It was found that the two kinds of LWI have some obvious differences not only from the steady outputs but also from the transient evolution processes. The effects of the unsaturated gain coefficient, cavity loss coefficient, ratio of the atomic injection rates and atomic exit rate on the transient evolution processes and steady outputs are discussed.

Comparison of laser performances of 5at.% Yb : Gd2xY2(1-x)SiO5 crystals between different cutting directions

We investigate the laser actions of 5at.% Yb:Gd2xY2(1-x)SiO5 (Yb:GYSO; x = 0.1) crystals with different cutting directions, parallel and vertical to the growth axis. Our results show that the cutting direction of the sample plays an astonished role in the laser operation. The sample cut vertically to the growth axis possesses the favourable lasing characteristics. Its output power reaches 3.13W at 1060nm with a slope efficiency of 44.68% when the absorbed pump power is 8.9 W. In contrast, the sample cut parallel reaches only 1.65 W at 1044 nm with a slope elLiciency of 33.76% with absorbed pump power of 7.99 W. The absorption and emission spectra of the two samples are examined and the merit factor M is calculated. Our analysis is in agreement well with the experimental results. The wavelength tuning range of the superior sample covers from 1013.68 nm to 1084.82 nm.

连续工作的体布拉格光栅外腔半导体激光器的温度特性

对体布拉格光栅(VBG)作为波长选择元件的外腔半导体激光器的波长锁定进行了实验研究,报道了连续运转输出功率达43.5 W的半导体激光器阵列的体布拉格光栅波长锁定实验结果,给出了不同热沉温度下的稳定的波长锁定结果,说明采用体布拉格光栅外腔将减小半导体激光器的温控压力。实验中发现,随着注入电流的增大,输出激光功率逐渐增强,锁定的激射波长向长波长方向偏移。在输出功率为34.5 W时,波长红移约0.56 nm。这一移动与实验测量的体布拉格光栅的温度特性相吻合。连续和高占空比运行、高输出功率情况下,在器件的设计和使用时应该考虑这一效应。

Femtosecond laser speckles

The concept of femtosecond laser speckles is put forward. The theory of a speckle pattern in light of finite bandwidth is applied to describe femtosecond laser speckles. Basic representations of the contrast and the spectral correlation of femtosecond laser speckles are presented. The relationship between the speckle contrast and the bandwidth of a femtosecond laser is given. Experimental results are given that indicate an obvious difference between the speckle patterns produced by a continuous-wave laser and those produced by a femtosecond laser. (c) 2005 Optical Society of America

连续波工作大功率半导体激光器阵列的温度分布

用Ansys软件模拟了大功率半导体激光器阵列的稳态温度分布，并对自行研制的半导体激光器阵列的温度变化进行了测试，结果表明理论计算与实验结果基本吻合。该模拟结果对大功率半导体激光器阵列的封装设计具有现实的指导意义。

Experimental study of the FemtoTalbot effect

Experimental investigation of Talbot self-imaging effect of an amplitude grating under illumination of femtosecond laser pulse -- the FemtoTalbot effect is reported. Theoretical analyzed results show that Talbot images under illumination of femtosecond laser pulses are not the same as that under continuous wave illumination. Experimental results are in good agreement with the theoretical analysis. We believe that the experimental investigation of the FemtoTalbot effect is highly interesting for the enormous potential applications of Talbot effect.

Yb：Y2O3陶瓷薄片激光器获得10．5W连续激光输出

室温下采用中心波长约970nm准直输出的大功率激光二极管模块作为抽运源，端面抽运双程吸收的腔型结构，抽运原子数分数为8％的Yb：Y2O3多晶透明陶瓷片获得连续激光输出。抽运阈值功率为7W，当抽运功率达到35W时，获得优化连续激光输出功率为10．5W，光光转换效率为30％，斜率效率为37．5％。激光输出功率随抽运功率基本呈线性增长。采用更高功率抽运源、优化谐振腔结构和减小热效应的影响，Yb：Y2O3陶瓷激光器的输出功率和效率将会得到进一步提高。

激光二极管连续抽运电光调Q Nd：YVO4激光器

报道了全固态激光器连续抽运高重复率电光调Q的实验和理论分析结果。用LGS（La3Ga5SiO14）晶体作电光调Q元件，在激光二极管（LD）端面抽运Nd：YVO4激光器中实现了较高重复率的电光调Q输出。实验中在10^4Hz重复率下，抽运功率为28w时，平均功率超过5W，脉冲宽度为7ns，峰值功率为70kW，并对不同重复率时的脉冲输出进行了比较，在低重复率下，脉宽〈6．5ns，峰值功率超过100kW。在理论上，通过对连续抽运时的电光调Q速率方程进行修正，并考虑放大自发辐射（ASE）的影响，对调Q激光器的储能过

侧面抽运国产Nd∶YAG陶瓷棒的激光特性

实验研究了激光二极管阵列(LDA)侧向抽运国产Nd∶YAG陶瓷棒的准连续及被动调Q激光输出特性。该陶瓷激光器采用LDA侧面紧密环绕均匀排布的抽运结构,陶瓷棒抽运区域长度为20 mm,其总尺寸为3 mm×35 mm,掺杂原子数分数为~1%。在千赫兹准连续运转条件下,当平-平谐振腔的输出耦合镜透过率为47.3%时,获得最大平均功率23 W的1064 nm激光输出,光束发散角为4.5 mrad,斜率效率达12%。在谐振腔内插入Cr4+∶YAG晶体作为被动调Q开关,成功地实现了陶瓷激光器千赫兹重复频率调Q激光脉冲输出,当Cr4+∶YAG晶体初始透过率为60%时,输出激光脉冲宽度(半峰全宽)可窄至14.5 ns,调Q动静比约为40%。

采用国产大模场面积双包层光纤的714W连续光纤激光器

采用两个中心波长约976nm准直输出的高功率半导体激光模块为抽运源，通过空间滤波和非球面透镜耦合技术，双端抽运长度为21m的大模场面积国产掺镱双包层光纤，获得了714．5W的高功率连续激光输出。采用反向抽运，当人纤抽运功率为760W时，激光输出功率达到501W；采用双端抽运，当人纤抽运功率为1137W时，获得了714．5W的高功率连续输出，光光转换效率为62．8％，斜率效率为67％。