Sudies on non-isothermal melt crystallization kinetics in PET/PEN/DBS blends

Macrokinetic models, namly the modified Avrami, Ozawa and Zibicki models, were applied to study the non-isothermal melt crystallization process of PET/PEN/DBS blends by DSC measurement. The modified Avrami model was found to describe the experimental data fairly well. With the cooling rates in the range from 5 to 20 K/min, Ozawa model could be well used to describe the early stages of crystallization. However, Ozawa model did not fit the polymer blends during the late stages of crystallization, because it ignored the influence of secondary crystallization. The crystallization ability of the blends decreases with increasing the DBS content from analysis by using Ziabicki kinetic model, which is similar to the results based on calculation of the effective energy barrier of the blends.

Comparison of biochemical effects induced by Changle between male and female rats using NMR and ICP-MS techniques

Metabolic profiles caused by rare earth complex were investigated using NMR and ICP-MS techniques. Male and female Wistar rats were treated orally with Changle (A kind of rare earth complex applied in agriculture to raise the production of crops) at dose of 2, 5 and 20 mg (.) kg(-1) body weight/day respectively for 90 d. Urine and serum samples are collected on 90 d. The relative concentrations of important endogenous metabolites in urine and serum are determined from H-1 NMR spectra and the contents of the four rare earth elements ( La, Ce, Pr and Nd) constituting Changle in the serum samples are measured by ICP-MS technique. Changle-induced renal and liver damage in rats is found based on the increase in the amounts of the amino acids, trimethylamine N-oxide, N, N-dimethyglycine, dimethylamine, succinate, aketoglutarate and ethanol as well as rare earth concentrations. The similarities and differentiations are found in the alteration patterns of metabolites and rare earth concentrations in serum.

Patterning and luminescent properties of nanocrystallineY(2)O(3): Eu3+ phosphor films by sol-gel soft lithography

Nanocrystalline Y2O3:Eu3+ phosphor films and their patterning were fabricated by a Pechini sol-gel process combined with a soft lithography. X-ray diffraction (XRD), thermogravimetric and differential thermal analysis (TG-DTA), atomic force microscopy (AFM), optical microscopy, UV/vis transmission and photoluminescence (PL) spectra as well as lifetimes were used to characterize the resulting films. The results of XRD indicated that the films began to crystallize at 500 degreesC and the crystallinity increased with the elevation of annealing temperatures. Uniform and crack free non-patterned phosphor films were obtained, which mainly consisted of grains with an average size of 70 nm. Using micro-molding in capillaries technique, we obtained homogeneous and defects-free patterned gel and crystalline phosphor films with different stripe widths (5, 10, 20 and 50 mum). Significant shrinkage (50%) was observed in the patterned films during the heat treatment process. The doped Eu3+ showed its characteristic emission in crystalline Y2O3 phosphor films due to an efficient energy transfer from Y2O3 host to them. Both the lifetimes and PL intensity of the Eu3+ increased with increasing the annealing temperature from 500 to 900 degreesC, and the optimum concentrations for Eu3+ were determined to be 5 mol%.

Preparation, patterning and luminescent properties of nanocrystalline Gd2O3 : A (A = Eu3+, Dy3+, Sm3+, Er3+) phosphor films via Pechini sol-gel soft lithography

Nanocrystalline Gd2O3:A (A = Eu3+, Dy3+, Sm3+, Er3+) phosphor films and their patterning were fabricated by a Pechini sol-gel process combined with a soft lithography. X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM) and optical microscopy, UV/vis transmission and photoluminescence (PL) spectra as well as lifetimes were used to characterize the resulting films. The results of XRD indicated that the films began to crystallize at 500 degreesC and that the crystallinity increased with the elevation of annealing temperatures. Uniform and crack free non-patterned phosphor films were obtained by optimizing the composition of the coating sol, which mainly consisted of grains with an average size of 70 nm and a thickness of 550 nm. Using micro-molding in capillaries technique, we obtained homogeneous and defects-free patterned gel and crystalline phosphor films with different stripe widths (5, 10, 20 and 50 mum). Significant shrinkage (50%) was observed in the patterned films during the heat treatment process. The doped rare earth ions (A) showed their characteristic emission in crystalline Gd2O3 phosphor films due to an efficient energy transfer from Gd2O3 host to them. Both the lifetimes and PL intensity of the rare earth ions increased with increasing the annealing temperature from 500 to 900 degreesC, and the optimum concentrations for Eu3+, Dy3+, sm(3+), Er3+ were determined to be 5, 0.25, 1 and 1.5 mol% of Gd3+ in Gd2O3 films, respectively.

Patterning and optical properties rhodamine B-doped organic-inorganic silica films fabricated by sol-gel soft lithography

Rhodamine B (RB)-doped organic-inorganic silica films and their patterning were fabricated by a sol-gel process combined with a soft lithography. The resulted film samples were characterized by atomic force microscope (AFM), optical microscope and UV/Vis absorption and photoluminescence excitation and emission spectra. The effects of the concentration of the RB dye and heat treatment temperature on the optical properties of the hybrid silica films have been studied. Four kinds of patterning structures with film line widths of 5, 10, 20 and 50 mum have been obtained by micromolding in capillaries by a soft lithography technique. The RB-doped hybrid silica films present a red color, with an excitation and emission bands around 564 and 585 mum, respectively. With increasing the RB concentration, the emission intensity of the RB-doped hybrid silica films increases and the emission maximum presents a red shift. The emission intensity of the films decreases with increasing the heat treatment temperatures.

溶胶凝胶软石印法制备Zn_2SiO_4∶Mn图案化薄膜及其发光性能的研究

采用溶胶 凝胶法制备了Zn2SiO4∶Mn薄膜并结合毛细管微模板技术实现了薄膜的图案化,利用X射线衍射(XRD),原子力显微镜,光学显微镜,发光光谱等手段对Zn2SiO4∶Mn的结晶过程、发光性质进行了研究。XRD结果表明,溶胶 凝胶法合成的样品在800℃时已开始结晶,在1000℃时可得到纯相的Zn2SiO4∶Mn,这比传统的固相法的烧结温度低150℃。Zn2SiO4∶Mn薄膜的激发光谱在220nm和280nm之间有一个强的吸收峰,峰值位于248nm,发射光谱的最大值位于522nm,为绿光发射。从原子力显微镜照片可知组成薄膜的粒子比较均匀,其平均直径为220nm。我们获得了四种图案化宽度,分别是5,10,20,50μm。光学显微镜的结果表明,图案薄膜烧结后相对于烧结前有10%～20%的收缩。

Non-isothermal crystallization behavior and kinetics of metallocene short chain branched polyethylene

The non-isothermal crystallization behavior and kinetics of metallocene short chain branched polyethylene were investigated via DSC at cooling rates from 2.5 to 20 degreesC/min, and subsequent heating at rate of 10 degreesC/min. To verify the effect of molecular weight and branching content on crystallization, three group samples were chosen: (1) linear polyethylene with low molecular weight and high molecular weight; (2) low molecular weight polyethylene with low branching content and high branching content; (3) high molecular weight polyethylene with low branching content and high branching content. The results show that crystallization temperature, crystallinity, melting temperature and crystallization rate are highly branching content-dependent. Molecular weight effect is less important, compared to branching content. A dramatic decrease of crystallization temperature, crystallinity, crystallization rate and melting temperature was observed for branched samples. The non-isothermal kinetics was analyzed via the methods, developed by Gupta and Mo Zhi-shen, and good agreement was obtained.

Morphologies and physical properties of PA1010/HIPS/HIPS-g-MA ternary blends

The effect of the content of a copolymer consisting of high impact polystyrene grafted with maleic anhydride (HIPS-g-MA) on morphological and mechanical properties of PA1010/HIPS blends has been studied. Blend morphologies were controlled by adding HIPS-g-MA during melt processing, thus the dispersion of the HIPS phase and interfacial adhesion between the domains and matrices in these blends were changed obviously. The weight fractions of HIPS-g-MA in the blends increased from 2.5 to 20, then much finer dispersions of discrete HIPS phase with average domain sizes decreased from 6.1 to 0.1 mu m were obtained. It was found that a compatibilizer, a graft copolymer of HIPS-g-MA and PA1010 was synthesized in situ during the melt mixing of the blends. The mechanical properties of compatibilized blends were obviously better than those of uncompatibilized PA1010/HIPS blends. These behaviors could be attributed to the chemical interactions between the two components of PA1010 and HIPS-g-MA and good dispersion in PA1010/HIPS/HIPS-g-MA blends. Evidence of reactions in the blends was seen in the morphology and mechanical behaviour of the solid. The blend containing 5 wt % HIPS-g-MA component exhibited outstanding toughness. (C) 1999 Kluwer Academic Publishers.

蒺藜化学成分的研究

目的：研究蒺藜(Tribulus terrestris L.)中生物活性物质。方法：用硅胶柱色谱、HPLC进行分离，根据光谱数据鉴定其结构。结果：分离纯化得到两种呋甾皂苷，确定其结构为26-Ｏ-β-D-吡喃葡糖基-(25R,S)-5α-呋甾-12-羰基-20(22)-烯基-3β,26-二醇-3-O-β-D吡喃葡糖基(1→4)-β-D-吡喃半乳糖苷(Ｉ)；26-Ｏ-β-D吡喃葡糖基-(25R)-5α-呋甾-12-羰基-3β,22α,26-三醇-3-Ｏ-β-D-吡喃葡糖基(1→2)-β-D-吡喃半乳糖苷(Ⅱ)。结论：Ｉ,Ⅱ均为新化合物

Morphological, thermal, and mechanical properties of polypropylene/polycarbonate blend

This work deals with the effect of compatibilizer on the morphological, thermal, rheological, and mechanical properties of polypropylene/polycarbonate (PP/ PC) blends. The blends, containing between 0 to 30 vol % of polycarbonate and a compatibilizer, were prepared by means of a twin-screw extruder. The compatibilizer was produced by grafting glycidyl methacrylate (GMA) onto polypropylene in the molten state. Blend morphologies were controlled by adding PP-g-GMA as compatibilizer during melt processing, thus changing dispersion and interfacial adhesion of the polycarbonate phase. With PP-g-GMA, volume fractions increased from 2.5 to 20, and much finer dispersions of discrete polycarbonate phase with average domain sizes decreased from 35 to 3 mu m were obtained. The WAXD spectra showed that the crystal structure of neat PP was different from that in blends. The DSC results suggested that the degree of crystallization of PP in blends decreased as PC content and compatibilizer increased. The mechanical properties significantly changed after addition of PP-g-GMA. (C) 1997 John Wiley & Sons, Inc.

La-Ba系氧化物催化剂用于甲烷氧化偶联

以La_2O_3为基础,碱土金属作为第二组分的二元氧化物催化剂均具有较高的生成C_2活性,特别是La-Ba-O系催化剂具有优良的甲烷氧化偶联活性和稳定性,当La/Ba原子比为2.5时,C_2收率可达20.3％。第三组分的添加有助于提高C_2选择性,特别是添加碱金属,可以抑制完全氧化反应,并提高乙烯/乙烷比。在La:Ba:Na=2.5:1:0.1的催化剂上进行了500/小时的寿命实验,在整个反应期间,催化剂的活性和选择性相当稳定。X-射线物相分析表明,新鲜催化剂除有少量的碳酸钡外,主要是氧化镧和氧化钡的混合物。500小时后的物相基本上是氧化镧和碳酸钡。使用前后催化剂的比表面积及表面La和Ba的分布均无改变。较高的CH_4/O_3比对提高C_2选择性有利,当CH_4:O_2=4:1时,C_2选择性和收率分别为65.1％和19.1％。

裂解色谱法研究环化顺-1,4-丁二烯-异戊二烯无规共聚物

如同顺-1,4-聚丁二烯(PBd)和聚异戊二烯(PIP),在一定的催化条件下,顺-1,4-丁二烯-异戊二烯无规共聚物(PBI,简称丁戊无规共聚物)可生成环化顺-1,4-丁戊无规共聚物(CP-BI)。作者曾报道用裂解色谱法表征环化顺-1,4-聚丁二烯(CPBd),本文对不同组成的CPBI和PBI进行了裂解色谱比较研究。 表1所列试样由实验室合成。用CDS pyro-probe 190型裂解器,SP-2305E型气相色谱仪,FID。裂解温度700℃,裂解时间5秒,色谱柱4mm×3m不锈钢柱,填充20%SE-30固定相(101白色担体),柱温106℃,载气氮气40mL/min。试样量约30μg,放于石英管内,后者再插入

异戊二烯均相聚合催化剂

分别用C_6H_5CH_2Cl,CH_2-CHSiCl_3,CH_ SiHCl_2,(CH_3)_2SiCl_2,(CH_3)_3CCl,CH_2—CHCH_2Cl,Cl_3SiCH_2CH_2SiCl_3代替非均相催化剂Nd(naph)_3-Al_2Et_3Cl-Al(i-Bu)_2H(简称Nd-Cl-Al)中的助催化剂后,除C_6H_5CH_2Cl,CH_2=CHSiCl_3,CH_SiHCl_2形成悬浊催化剂外,在Cl/Nd<8(mol比)时,其他氯化物均形成均相催化剂,并能催化异戊二烯均相聚合,得到顺式-1,4含量约95％,[η]约3 dL/g的聚合物。分别用(CH_3)_3CCl和(CH_3)_2SiCl_2代替Cl所组成的两催化剂,其催化活性接近,最佳Al/Nd和Cl/Nd值分别为40和2.5;异戊二烯浓度为10％—20％时,转化率不随其浓度的改变而变化。符合一级反应动力学特征。

11-钨硼酸钾的结构和振动光谱研究

标题化合物K_8H〔BW_(11)O_(39)〕·13H_2O属立方晶系,空间群P43m,a=10.710(1)A,V=1228.58A~3,Z=1;D_O=4.39g·cm~(-3),D_c=4.42g·cm~(-3)。(BW_(11)O_(3.9)~(9-)离子属于不饱和α-Keggin型结构,B原子位于O_a四面体的中心。测定并研究了化合物的IR和Raman光谱性质。

Effect of stocking density on growth, settlement and survival of clam larvae, Meretrix meretrix

To determine the optimal larval density for hatchery culture of the clam Meretrix meretrix, experiments with stocking densities of 5, 10, 20, 40 and 60 larvae ml(-1) were designed, which included the developmental stages from D-veliger to 8 days postsettlement. Shell length, settlement time and survival rate of the larvae were recorded. Results showed that, at each sampling time, larvae reared at the highest density had the smallest mean size, whereas larvae reared at the lowest density had the largest mean size. Statistical differences in mean shell length at different stocking densities appeared from day 2, and greater differences occurred with increased culture time. Specific growth rate (SGR) in the rapid growing stage (day 0-3) was negatively correlated with density; however, no correlation was found between SGR and density in the slow growing stage (days 3-7). Settlement time was prolonged and shell length of settled larvae decreased as density increased. However, larval survival rate (74.8-79.1%) was independent of stocking density. Results showed that a high stocking density, in the designated range, is feasible for larval culture of the clam M. meretrix. However, for large-scale culture, in the interest of costs and safety, a stocking density of 10-20 larvae ml(-1) is recommended. (c) 2006 Elsevier B.V. All rights reserved.