(19)~F+(27)~Al耗散反应中双核系统的转动与衰变

测量了19F+27Al耗散反应产物B,C,N,O,F和Ne的激发函数,入射束流的能量从110.25MeV 到118.75MeV,能量步长为250keV.用能量自关联函数方法从激发函数中提取了各反应产物的平均衰变宽度,利用同时考虑反应中所形成的中间双核系统的转动特性和衰变特性而发展了的Ericson核反应统计理论,讨论了19F+27Al耗散反应中双核系统随时间的演化过程.

~(19)F+~(27)Al反应产物的角分布、角分散与耗散机制

完成了114MeV19F+27Al深部非弹性碰撞产物的角分布测量.分析了反应产物B,C,N,O,F,Ne,Na,Mg和Al的实验室系角分布,讨论了反应形成的中间双核系统随时间演化过程中角分布所表现出的耗散特点.从实验上提取了反应产物各元素的角分散参数并作了角分散参数的理论拟合,讨论了角分散参数的物理意义以及角分散参数与耗散反应产物的电荷数Z之间的依赖关系.

~(19)F+~(27)Al深部非弹性碰撞产物的角分布

完成了19F+27Al深部非弹性碰撞产物的角分布测量.初步分析了反应产物B,C,N,O,F,Ne,Na,Mg和Al的实验室系角分布,展现出深部非弹性反应机制的特点,显示了反应系统随时间的演化过程.

Sputtering induced by highly charged Pb-208(q+) bombardment on Al surface

Highly charged ions (HCls) carrying high Coulomb potential energy (E-p) could cause great changes in the physical and chemical properties of material surface when they bombard on the solid surface. In our work, the secondary ion yield dependence on highly charged Pbq+ (q = 4-36) bombardment on Al surface has been investigated. Aluminum films (99.99%) covered with a natural oxide film was chosen as our target and the kinetic energy (E-k) was varied between 80 keV and 400 keV. The yield with different incident angles could be described well by the equation developed by us. The equation consists of two parts due to the kinetic sputtering and potential sputtering. The physical interpretations of the coefficients in the said equation are discussed. Also the results on the kinetic sputtering produced by the nuclear energy loss on target Surface are presented.

Studies on the exotic structure of Al-23

The longitudinal momentum distribution (P-//) of fragments after one-proton removal from Al-23 and reaction cross sections (sigma(R)) for Al-23,Al-24 on carbon target at 74A MeV have been measured simultaneously. An enhancement in sigma(R) is observed for Al-23 compaxed with Al-24. The full width at half maximum of the P-// distribution for Mg-22 fragments has been determined to be 232 +/- 28 MeV/c. Analysis of P-// using the Few-Body Glauber Model indicates a dominant d-wave configuration for the valence proton in the ground state of Al-23. The exotic structure in Al-23 is discussed.

Rotation and deformation of the dinuclear system formed in dissipative reaction of F-19+Al-27

Excitation functions of the reaction products B, C, N, O, F and Ne emitted from the dissipative reaction of (19) F+(27) Al have been measured at incident energies from 110.25MeV to 118.75MeV in steps of 250keV. The moments of inertia of the intermediate dinuclear system formed in the reaction are extracted from the energy autocorrelation functions of the products. Comparing the moment of inertia extracted from the experimental data with the calculated one by using the sticking limit, it indicates that the formed dinuclear system has a large deformation in the reaction process.

Measurement of K*(892)(0) and K-0 mesons in Al plus Al collisions at 1.9A GeV

A new measurement of subthreshold K*(892)(0) and K-0 production is presented. The experimental data complete the measurement of strange particles produced in Al + Al collisions at 1.9A GeV measured with the FOPI detector at SIS at GSI (Darmstadt). The K*(892)(0)/K-0 yield ratio is found to be 0.0315 +/- 0.006(stat.) +/- 0.012(syst.) and is in good agreement with the transport model prediction. These measurements provide information on the in-medium cross section of K+-pi(-) fusion, which is the dominant process in subthreshold K*(892)(0) production.

Effect of substrate and annealing on the structural and optical properties of ZnO:Al films

ZnO:Al thin films with c-axis preferred orientation were deposited on glass and Si substrates using RF magnetron sputtering technique. The effect of substrate on the structural and optical properties of ZnO:Al films were investigated. The results showed a strong blue peak from glass-substrate ZnO:Al film whose intensity became weak when deposited on Si substrate. However, the full width at half maxima (FWHM) of the Si-substrate ZnO:Al (0 0 2) peaks decreased evidently and the grain size increased. Finally, we discussed the influence of annealing temperature on the structural and optical properties of Si-substrate ZnO:Al films. After annealing, the crystal quality of Si-substrate ZnO:Al thin films was markedly improved and the intensity of blue peak (similar to 445 nm) increased noticeably. This observation may indicate that the visible emission properties of the ZnO:Al films are dependent more on the film crystallinity than on the film stoichiometry. Crown Copyright (C) 2009 Published by Elsevier Ltd. All rights reserved.

Studying the Attribution of LiF in OLED by the C-V Characteristics

The organic light-emitting device (OLED) with simple structures of indium tin oxide (ITO)/tris(8-quinolinolato) aluminum (Alq(3))/LiF/Al and ITO/Alq(3)/Al was fabricated to analyze the contribution of LiF in OLED. We used the C-V characteristics to investigate the contribution of LiF in OLED and found that the capacitance of the above-mentioned structures was 12.5 nF and 77.5 nF, respectively. It is shown that the LiF layer affects the property of OLED resulting in the change of the capacitance of the device.

MEASUREMENT OF TWO-PROTON CORRELATION FROM THE BREAK-UP OF Al-23

Experiments of Al-23 and Mg-22 radioactive beams bombarding a C-12 target at an energy of 60 similar to 70 A MeV have been performed at the projectile fragment separator beamline (RIPS) in the RIKEN Ring Cyclotron Facility to study the two-proton emission from Al-23 and Mg-22 excited states, respectively. The trajectorie of the decay products, namely Na-21 + p + p from Al-23 and Ne-20 + p + p from Mg-22, are clean identified. The relative momentum and opening angle between two protons in the rest frame of three body decay channels are obtained by relativistic-kinematics reconstruction. The results demonstrate that there are some di-proton emission components from He-2 cluster for the excited Al-23 and Mg-22.

Direct synthesis of Al-SBA-15 mesoporous materials via hydrolysis-controlled approach

Aluminum-substituted mesoporous SBA-15 (Al-SBA-15) materials were directly synthesized by a hydrolysis-controlled approach in which the hydrolysis of the silicon precursor (tetraethyl orthosilicate, TEOS) is accelerated by fluoride or by using tetramethyl orthosilicate (TMOS) as silicon precursor rather than TEOS. These materials were characterized by powder X-ray diffraction (XRD), N-2 sorption isotherms, TEM, Al-27 MAS NMR, IR spectra of pyridine adsorption, and NH3-TPD. It is found that the matched hydrolysis and condensation rates of silicon and aluminum precursors are important factors to achieve highly ordered mesoporous materials. Al-27 MAS NMR spectra of Al-SBA-15 show that all aluminum species were incorporated into the silica framework for the samples prepared with the addition of fluoride. A two-step approach (sol-gel reaction at low pH followed by crystallization at high pH) was also employed for the synthesis of Al-SBA-15. Studies show that the two-step approach could efficiently avoid the leaching of aluminum from the framework of the material. The calcined Al-SBA-15 materials show highly ordered hexagonal mesostructure and have both Bronsted and Lewis acid sites with medium acidity.

Fabrication, thermal stability and mechanical properties of novel (W0.5Al0.5)C-0.8-Co composite prepared by mechanical alloying and hot-pressing sintering

A novel cemented carbides (W0.5Al0.5)C-0.8-Co with different cobalt contents were prepared by mechanical alloying and hot-pressing technique. Hot-pressing technique as a common technique was performed to fabricate the bulk bodies of the hard alloys. The novel cemented carbides have superior mechanical properties compared to WC-Co. The density, operating cost of the novel material were much lower than WC-Co. There is almost no eta-phase in the (W0.5Al0.5)C-0.8-Co cemented carbides system although the carbon deficient get the value of 20%, and successfully got the nanostructured rounded (W0.5Al0.5)C-0.8 particles.

Efficient inverted top-emitting organic light-emitting diodes using ultrathin MoO3/C-60 bilayer structure to enhance hole injection

Efficient inverted top-emitting organic light-emitting diodes with aluminum (Al) as both the cathode and semitransparent anode are investigated. It is found that introduction of the ultrathin molybdenum trioxide (MoO3)/fullerene (C-60) bilayer structure between the low work function Al top anode and the hole-transporting layer dramatically enhances the device performance as compared to the devices with sole MoO3 or C-60 buffer layer. The ultraviolet photoemission spectroscopy and x-ray photoelectron spectroscopy indicate that the hole injection barrier between Al anode and hole-transporting layer is effectively reduced via strong dipole effect at Al/MoO3/C-60 interfaces with its direction pointing from Al to C-60.

Preparation of W-Al-Mo ternary alloys by mechanical alloying

Single phase WxAl(50)Mo(50)-X (X=40, 30, 20 and 10) powders have been synthesized directly by mechanical alloying (MA). The structural evolutions during MA and subsequent as-milled powders by annealing at 1400 degrees C have been analyzed using X-ray diffraction (XRD). Different from the Mo50Al50 alloy, W40Al50Mo10 and W30Al50Mo20 alloys were stable at 1400 degrees C under vacuum. The results of high-pressure sintering indicated that the microhardnesses of two compositions, namely W40Al50Mo10 and W30Al50Mo20 alloys have higher values compared with W50Al50 alloy.

Synthesis, crystal structure, and density of (W1-xAlx)C

A new solid solution system of Al in WC, with the stoichiometry of (W1-xAlx)C (x = 0.10, 0.25, 0.50, 0.75, 0.86), has been synthesized by a solid-state reaction between W1-xAlx alloys and carbon at around 1673 K in vacuum. Environment scanning electron microscope, energy- dispersive analysis of X-ray, X-ray photoelectron spectroscopy, and inductively coupled plasma analyses are used to certify the formation of the products. The mechanism of the solid-state reaction is also discussed. (W1-xAlx)C is identified to crystallize in the hexagonal space group P6m2 (No. 187) and belongs to the WC structure type. The atoms of W and Al occupy the same lattice site (la site) in the cell of (W1-xAlx)C. The cell parameters for each specimen in the phase of W-AI-C are quite close to that of WC, while their densities are far lower than that of WC.