Alteration of metallothionein mRNA in bay scallop Argopecten irradians under cadmium exposure and bacteria challenge

Metallothionein (MT) is a superfamily of cysteine-rich proteins contributing to metal metabolism, detoxification of heavy metals, and immune response such as protecting against ionizing radiation and antioxidant defense. A metallothionein (designated AiMT2) gene was identified and cloned from bay scallop, Argopecten irradians. The full length cDNA of AiMT2 consisted of an open reading frame (ORF) of 333 bp encoding a protein of 110 amino acids. with nine characteristic Cys-X-Cys, five Cys-X-X-Cys, five Cys-X-X-X-Cys and two Cys-Cys motif arrangements and a conserved structural pattern Cys-x-Cys-x(3)-Cys-Tyr-x(3)Cys-x-Cys-x(3)-Cys-x-Cys-Arg at the C-terminus. The cloned ANT showed about 50% identity in the deduced amino acid sequence with previously published MT sequences of mussels and oysters. The conserved structural pattern and the close phylogenetic relationship of AiMT2 shared with MTs from other mollusc especially bivalves indicated that AiMT2 was a new member of molluscan MT family. The mRNA transcripts in hemolymph of AiMT2 under cadmium (Cd) exposure and bacteria challenge were examined by real-time RT-PCR. The mRNA expression of AiMT2 was up-regulated to 3.99-fold at 2 h after Listonella anguillarum challenge, and increased drastically to 66.12-fold and 126.96-fold at 16 and 32 h post-challenge respectively. Cadmium ion exposure could induce the expression of AiMT2, and the expression level increased 2.56-fold and 6.91-fold in hemolymph respectively after a 10-day exposure of 100 mu g L-1 and 200 mu g L-1 CdCl2. The sensitivity of AiMT2 to bacteria challenge and cadmium stress indicated it was a new Cd-dependent MT in bay scallop and also regulated by an immune challenge. The changes in the expression of AiMT2 could be used as an indicator of exposure to metals in pollution monitoring programs and oxidative stress, and bay scallop as a potential sentinel organism for the cadmium contamination in aquatic environment. (C) 2008 Elsevier Inc. All rights reserved.

Manganese abnormity in holocene Sediments of the Bohai Sea

Manganese abnormity has been observed in the Holocene sediments of the mud area of Bohai Sea. On the basis of grain size, chemical composition, heavy mineral content and accelerator mass spectrometry (AMS) C-14 dating of foraminifer, relationships between manganese abnormity and sedimentation rates, material source, hydrodynamic conditions are probed. Manganese abnormity occurred during the Middle Holocene when sea level and sedimentation rates were higher than those at present. Sedimentary hiatus was not observed when material sources and hydrodynamic conditions were quite similar. Compared with the former period, the latter period showed a decrease in reduction environment and an inclination toward oxidation environment with high manganese content, whereas provenance and hydrodynamic conditions showed only a slight change. From the above observations, it can be concluded that correlation among manganese abnormity, material source, and hydrodynamic conditions is not obvious. Redox environment seems to be the key factor for manganese enrichment, which is mainly related to marine authigenic process.

River mouth bar formation, riverbed aggradation and channel migration in the modern Huanghe (Yellow) River delta, China

This paper addresses the recent (1970s-1990s) processes of river mouth bar formation, riverbed aggradation and distributary migration in the Huanghe River mouth area, in the light of station-based monitoring, field measurements and remote sensing interpretation. The results show that the morphological changes of the river mouth bar have been closely associated with the largely reduced fluvial discharge and sediment load. Landforrn development such as bar progradation occurred in two phases, i.e. before and after 1989, which correspond to faster and lower bar growth rates, respectively. Fast riverbed aggradation in the mouth channel was strongly related to river mouth bar progradation. During 1976-1996, about 2.8% of the total sediment loads were deposited in the river channel on the upper to middle delta. Therefore, the river water level rose by a few meters from 1984 to 1996. The frequent distributary channel migration, which switched the radial channel pattern into the SE-directed pattern in the mid-1980s, was linked with mouth bar formation. Marine conditions also constrain seaward bar progradation. Furthermore, the history of river mouth bar formation reflects human impacts, such as dredging and dyking in order to stabilize the coastal area. (c) 2005 Elsevier B.V. All rights reserved.

Persistent organic pollutant residues in the sediments and mollusks from the Bohai Sea coastal areas, North China: An overview

The Bohai Sea costal area is one of the most developed zones of China and the sewage water from populous and developed cities, including Beijing, Tianjin. Qinhuangdao and Dalian is discharged into the Bohai Sea. Additionally, its semi-enclosed characteristic restricts water exchange, which leads to high accumulation of pollutants in the environment. This overview presents the residues of 6 classes of Persistent Organic Pollutants (POPs). including PAHs, DDTs. HCHs, PCBs and PCDD/Fs. in the sediments and mollusks of the Bohai Sea through analyzing previous literatures. In the sediments. the highest PAH concentrations were detected in the vicinities of Qinhuangdao, while the northeast corner of the Bohai Bay possessed the highest levels of DDTs and PCBs. The investigations on HCHs and PCDD/Fs distributions on the whole sea scale have not been reported. In mollusks, PAH concentrations were in the same order of magnitude in the whole Bohai Sea, so were DDTs. HCHs and PCBs, while the outlier maximum values of PCDDs and PCDFs occurred in Yingkou. In general, the POPs residues in mollusks collected from Shandong Province were higher than the other areas. The compositions of DDTs, HCHs and PCBs in sediments indicated their recent usage. By comparing POP concentrations in sediments with the recommended criterions, it was shown that some individual PAH compounds occasionally associated with adverse biological effects in the vicinities of the Liaodong Bay and Qinhuangdao, and the Liaohe River Estuary were heavily contaminated with DDTs, but PCBs were all below the thresholds. In order to reveal the transference and transformation of POPs in the environment, further studies concerning with their behavior, fate and bioaccumulation in the different trophic levels should be programmed. Moreover, laws and regulations should be enforced to ban the illegal usage of POPs-containing pesticides to guarantee health of the environment and human. (C) 2008 Elsevier Ltd. All rights reserved.

Inorganic carbon of sediments in the Yangtze River Estuary and Jiaozhou Bay

JGOFS results showed that the ocean is a major sink for the increasing atmospheric carbon dioxide resulting from human activity. However, the role of the coastal seas in the global carbon cycling is poorly understood. In the present work, the inorganic carbon (IC) in the Yangtze River Estuary and Jiaozhou Bay are studied as examples of offshore sediments. Sequential extraction was used to divide inorganic carbon in the sediments into five forms, NaCl form, NH3 H2O form, NaOH form, NH2OH HCl form and HCl form. Studied of their content and influencing factors were also showed that NaCl form < NH3 H2O form < NaOH form < NH2OH HCl form < HCl form, and that their influencing factors of pH, Eh, Es, water content, organic carbon, organic nitrogen, inorganic nitrogen, organic phosphorus and inorganic phosphorus on inorganic carbon can be divided into two groups, and that every factor has different influence on different form or on the same form in different environment. Different IC form may transform into each other in the early diagenetic process of sediment, but NaCl form, NH3 H2O form, NaOH form and NH2OH HCl form may convert to HCl form ultimately. So every IC form has different contribution to carbon cycling. This study showed that the contribution of various form of IC to the carbon cycle is in the order of NaOH form > NH2OH HCl form > NH3 H2O form > NaCl form > HCl form, and that the contribution of HCl form contributes little to carbon cycling, HCl form may be one of end-result of atmospheric CO2. So Yangtze River estuary sediment may absorb at least about 40.96x10(11) g atmospheric CO2 every year, which indicated that offshore sediment play an important role in absorbing atmospheric CO2.

Corrosion of steel structures in sea-bed sediment

Seabed sediment (SBS) is a special soil that is covered by seawater. With the developments in marine oil exploitation and engineering, more and more steel structures have been buried in SBS. SBS corrosion has now become a serious problem in marine environment and an important issue in corrosion science. In this paper, approach in the field of SBS corrosion is reviewed. Electrochemical and microbial corrosion factors, corrosion mechanism, measurement of metal corrosion rate, corrosion evaluation and prediction of corrosion are also discussed here.

Study on steel corrosion in different seabed sediments

A series of simulation experiments on carbon steel (A(3) steel) and low alloy steel (16 Mn steel) in marine atmosphere (MA), seawater (SW) and seabed sediment (SBS) including rough sea sand, fine sea sand and seabed mud were carried out indoors for a year or so by means of individually hanging plates (IHP) and electrically connected hanging plates (ECHP). The corrosion of steels in SBS was mainly due to the macrogalvanic cell effect. The steel plates at the bottom of SBS, as the anode of a macrogalvanic cell, showed the heaviest corrosion with a corrosion rate of up to 0.12 mm/a, approximately equal to that of steel plates in marine atmosphere. The test results showed that the corrosion rates of A(3) and 16 Mn steel in marine environment were in the order: MA > SW > SBS by the IHP method; and MA > SBS > SW by the ECHP method. The corrosion rates of steels in the water/sediment interface were directly proportional to the grain size of the SBS by the ECHP method, but those of steels in the water/sediment interface did not vary with the grain size of SBS by the IHP method. The corrosion rate of low-alloy steel was a little higher than that of carbon steel. The results of this study have important applications for design of offshore steel structures such as oil platform, pier, and port.

Effect of sulfate-reducing bacteria on corrosion behavior of mild steel in sea mud

Microbiologically influenced corrosion (MIC) is very severe corrosion for constructions buried under sea mud environment. Therefore it is of great importance to carry out the investigation of the corrosion behavior of marine steel in sea mud. In this paper, the effect of sulfate-reducing bacteria (SRB) on corrosion behavior of mild steel in sea mud was studied by weight loss, dual-compartment cell, electronic probe microanalysis (EPMA), transmission electron microscopy (TEM).combined with energy dispersive X-ray analysis (EDX) and electrochemical impedance spectroscopy (EIS). The results showed that corrosion rate and galvanic current were influenced by the metabolic activity of SRB. In the environment of sea mud containing SRB, the original corrosion products, ferric (oxyhydr) oxide, transformed to iron sulfide. With the excess of the dissolved H2S, the composition of the protective layer formed of FeS transformed to FeS2 or other non-stoichiometric polysulphide, which changed the state of the former layer and accelerated the corrosion process.

Leaf orientation, incident sunlight, and photosynthesis in the alpine species Suassurea superba and Gentiana straminea on the Qinghai-Tibet Plateau

The extremely high level of solar radiation on the Qinghai-Tibet Plateau may induce photoinhibition and thus limit leaf carbon gain. To assess the effect of high light, we examined gas exchange and chlorophyll fluorescence for two species differing in light interception: the prostrate Saussurea superba and the erect-leaved Gentiana straminea. In controlled conditions with favorable water and temperature, neither species showed apparent photoinhibition in gas exchange measurements. In natural environment, however, their photosynthetic rate decreased remarkably at high light. Photosynthesis depression was aggravated under high leaf temperature or soil water stress. Relative stomatal limitation was much higher in S. superba than in G. straminea and it remarkably increased in the later species at midday when soil was dry. F-v/F-m as an indicator for photoinhibition was generally higher in S. superba than in the other species. F-v/F-m decreased significantly under high light at midday in both species, even when soil moisture was high. F-0 linearly elevated with the increment of leaf temperature in G. straminea, but remained almost constant in S. superba. Electron transport rate (ETR) increased with photosynthetically active photon flux density (PPFD) in S. superba, but declined when PPFD was high than about 1000 mumol m(-2) s(-1) in G. straminea. Compared to favorable environment, the estimated daily leaf carbon gain at PPFD above 800 mumol m(-2) s(-1) was reduced by 32% in S. superba and by 17% in G. straminea when soil was moist, and by 43% and 53%, respectively, when soil was dry. Our results suggest that the high radiation induces photoinhibition and significantly limits photosynthetic carbon gain, and the limitation may further increase at higher temperature and in dry soil.

基于栅格地图的多化学羽流源定位

本文研究了移动机器人在湍流环境中定位多个化学羽流源的问题。利用粒子随机行走方法建立动态羽流模型。在此环境中机器人进行梳状搜索并采集羽流数据,使用一种基于后验概率独立假设的改进贝叶斯算法融合这些传感器数据建立一张羽流源位置的概率地图,地图中具有高概率值的栅格指出了羽流源可能的位置。仿真结果说明了该方法的有效性,通过与标准贝叶斯算法的比较说明了该方法优点。

重庆老龙洞二叠系-三叠系界线地层微生物岩研究

The largest mass extinction in the Phanerozoic happened at the end of the Permian. The microbialites formed in the extreme environments after the mass extinction has become a hotspot for geologists and paleontologists throughout the world. The dendroid microbialites that were described for the first time in 1999 from the Permian-Triassic boundary section at Laolongdong, Chongqing, have been studied by many geologists from China and overseas. Two important viewpoints about their origin have been proposed. Some researchers believed that they resemble Quaternary travertine shrubs in form, and may belong to microbialites. Some other researchers proposed that the dendroid structure is composed of clots formed by coccoidal cynaobacteria, and is microbialite. Our detailed survey on the section reveals that: (1) there is an interval of speckled “microbialite” in the section, and it underlies the dendroid “microbialite”, (2) the dendroid “microbialite” does not always have dendroid appearance; they are dendroid only in very local places; they are not dendroid in most places; for this reason, they are not comparable to recent tufa; (3) the volume of the dendroid structure greatly increases toward the top of the dendroid microbialite interval: accounting to 70% of the whole rock in the top part. This distribution pattern implies that the formation of this structure may be related to downward migration of the diagenetic fluid. Examination of thin sections reveals that the dendroid structure or point-like structure in the “microbialite” look as lighter areas in the thin sections and are composed of large blocky clear calcites containing scattered yellow dirty small calcite rhombi and irregular “points” of relict lime mudstone or wackestone or packstone. Their formation is by any one of the following two processes: (1) dissolution → filling of large blocky calcite; (2) dolomitization → dedolomitization → dissolution by meteoric fresh water → filling by large blocky calcites. It has been found that there are at least two sea-level falls during the P-T transition. As the sea level fall, the carbonate deposits came into supratidal environment, and suffered dolomitization caused by evaporative fluid or mixing water of sea water and meteoric water. Since the fluid migrated downward from the top of the deposits and in random pathway, the dolomitization formed dendroid or speckled dolomitic areas. As the deposits came into subaerial environments, the meteoric fresh water migrated along the dendroid or speckled dolomitic area with higher porosity, and dissolution happened, which caused the rock became spongy or alveolate. In later time, after the strata came into phreatic zone, large clear blocky calcites grew in and filled the pores in the spongy areas. The dendroid and speckled structure were formed in this way, rather than composed of clots formed by coccoid cyanobecteria. The microbial fossils in Laolongdong section include two types. The first is the tube-like cyanobecteria in middle Bed 3, which are generally less than 1 mm in length, taper toward one end, and are internally filled by microspars. They are straight or sinuous, with micritic wall 0.005~0.01 mm thick. Since this kind of microbial fossils are abundant in middle Bed 3, this rock belongs to microbialite. The second type occurs in Bed 5 and lower and middle Bed 6. They are irregular globular in shape, generally 0.2 ~ 0.5 mm in size, with several outward progresses, and internally filled by one layer of needle-like calcite cements on the wall and the large blocky calcite in the inner space. According to their shape and preservation way, it is inferred that this kind of fossils were formed from some kind of bacterial colony. The bacterial colony may be cuticle in composition, since it has some hardness as it is indicated by its resistance to deposit loading. These organisms discomposed during diagenetic time, and formed good porosity. In later diagenetic time, these pores were firstly cemented by needle-like calcites and later filled by large blocky calcites. So, the bacterial colony promoted the formation of dendroid and speckled structures. However, they did not always form such structures. On the other hand, even though no bacterial colony or other microbes or any kind of fossils were present, dendroid or speckled structures can form. Bed 4 of Laolongdong section contains abundant gastropods but no microbial fossils, and is not microbialite, even though it is speckled. The top of Bed 6 is dendroid, but contain no microbial fossils, and is not micrbialite.

Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry with a matrix of carbon nanotubes for the analysis of low-mass compounds in environmental samples

The use of matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF-MS) for environmental analysis has been mainly focused on qualitative analysis of high-mass molecules, such as toxins, humic acid, and microorganisms. Herein,we describe a novel MALDI-TOF-MS method with a matrix of oxidized carbon nanotubes for analysis of low-mass compounds in environmental samples. A number of chemicals in the environment were qualitatively analyzed by the present method, and it was found that most of them, especially the highly polar chemicals, were measurable with high sensitivity. With the intrinsic ability to measure high-mass chemicals, this method can compensate for the current shortage of methods for environmental analysis for the measurement of highly polar or high-mass chemicals. For sample analysis, arsenic speciation in Chinese traditional medicines was qualified and diphenylolpropane in water samples was quantified. With the relatively high tolerance of the method to interfering molecules, a simple pretreatment or even no pretreatment could be employed before MS detection. Furthermore, this method can be employed in a high-throughput format.