Role of the evanescent states in the electron transport in quantum waveguides

Recognizing the computational difficulty due to the exponential behavior of the evanescent states in the calculations of the electron transmission in waveguide structures, the authors propose two transfer matrix methods and apply them to investigate the influence of the evanescent states on the electron wave propagation. The study shows that the effect of the evanescent states on the electron transport is obvious when the electron energy is close to the subband minima. The results show that the calculated transmissions are much enhanced if the evanescent states are omitted in the calculations. For the multiple-stub structures, it is found that the connecting channel length has a critical effect on the electron transmission depending on it larger or smaller than the attenuation lengths of evanescent states. Based on the study of the evanescent states, a new kind of waveguide structures which exhibit quantum modulated transistor action is proposed. (C) 1997 American Institute of Physics.

Theoretical Study on the Butt-coupling of Semiconductor Laser and Fiber Bragg Grating

The butt-coupling between a semiconductor laser diode and a fiber Bragg grating external cavity acts a key roll on the laser characteristics. The scatter matrix method considering the butt-coupling efficiency is used to analyze the butt-coupling between them. It is found that the butt-coupling distance and coupling efficiency determine the laser characteristics. For strong feedback, the single lasing wavelength changes in the reflection bandwidth of the effective reflectivity ( approximately the Bragg region of the fiber Bragg grating) as the distances change. For weak feedback condition, some different results are obtained. The SMSRs in the two conditions are presented and analyzed. These results can provide important design guidance of device parameters for the practical fabrication.

Fabrication of silicon-on-reflector for Si-based resonant-cavity-enhanced photodetectors

A novel silicon-on-reflector substrate for Si-based resonant-cavity-enhanced photodetectors has been fabricated by using Si-based sol-gel and smart-cut techniques. The Si/SiO2 Bragg reflector is controlled in situ by electron beam evaporation and the thickness can be adjusted to get high reflectivity. The reflectance spectra of the silicon-on-reflector substrate with five pairs of Si/SiO2 reflector have been measured and simulated by transfer matrix model. The reflectivity at operating wavelength is close to 100%. Based on the silicon-on-reflector substrate, SiGe/Si multiple quantum wells resonant-cavity-enhanced photodetectors for 1.3 mu m wavelength have been designed and simulated. Ten-fold enhancement of the quantum efficiency of resonant-cavity-enhanced photodetectors compared with conventional photodetectors is predicted.

Evaluation of the Uncertainties Caused by the Forward Scattering in Turbidity Measurement of the Coagulation Rate

The forward scattering light (FSL) received by the detector can cause uncertainties in turbidity measurement of the coagulation rate of colloidal dispersion, and this effect becomes more significant for large particles. In this study, the effect of FSL is investigated on the basis of calculations using the T-matrix method, an exact technique for the computation of nonspherical scattering. The theoretical formulation and relevant numerical implementation for predicting the contribution of FSL in the turbidity measurement is presented. To quantitatively estimate the degree of the influence of FSL, an influence ratio comparing the contribution of FSL to the pure transmitted light in the turbidity measurement is introduced. The influence ratios evaluated under various parametric conditions and the relevant analyses provide a guideline for properly choosing particle size, measuring wavelength to minimize the effect of FSL in turbidity measurement of coagulation rate.

Study on the localization of the electric dipole sources

The research of dipole source localization has great significance in both clinical research and applications. For example, the EEG recording from the scalp is widely used for the localization of sources of electrical activity in the brain. This paper presents a closed formula that describes the electric field of dipoles at arbitrary position, which is a linear transformer called the transfer matrix. The expression of transfer matrix and its many useful characteristics are given, which can be used for the analysis of the electrical fields of dipoles. This paper also presents the closed formula for determining the location and magnitude of single dipole or multi-dipoles according to its electrical field distribution. A calculation result for a single dipole shows that the dipole will be located at the midpoint of a line segment if there are equivalent fields at its two ends.

Relativistic photoionization cross sections for atomic Mg

The photoionization cross sections of the ground level (3s(2) S-1(0)) of atomic Mg have been studied theoretically in the energy region between the Mg+(3s) and Mg+(3p) threshold using the fully relativistic R-matrix method. The positions and widths of resonances have also been obtained and compared with a recent experiment (Wehlitz et al 2007 J. Phys. B 40 2385). Excellent agreement is shown between our theoretical calculations and experimental measurements. In the present calculations, five Rydberg series of doubly excited states have been exhibited, i.e. 3pns P-1, 3pnd P-1, 3pns P-3, 3pnd D-3 and 3pnd P-3, where 3pnd P-3 are confirmed as the fifth series in contrast to the previous theoretical results.

Electron collision cross sections and rate coefficients for the Na-like Cu ion

Collision cross sections are calculated using the R-matrix method for excitations between the three lowest LS states for Na-like Cu ion. The complex resonance structures are investigated. The collision rate coefficients have been calculated assuming a Maxwellian distribution of electron-impact energies. The results of the collision cross sections are in good agreement with those of the other theory.

The preparation and bioactivity research of agaro-oligosaccharides

Agaro-oligosaccharides were hydrolytically obtained from agar using hydrochloric acid, citric acid, and cationic exchange resin (solid acid). The FT-IR and NMR data showed that the hydrolysate has the structure of agaro-oligomers. Orthogonal matrix method was applied to optimize the preparation conditions based on alpha-naphthylamine end-labeled HPLC analysis method. The optimal way for oligosaccharides with different degree of polymerization (DP) was achieved by using solid acid degradation, which could give high yield and avoid solution neutralization process. Agaro-oligosaccharides with high purity were consequently obtained by activated carbon column isolation. Furthermore, the antioxidant and alpha-glucosidase inhibitory activity of three fractions were also investigated. The result indicated that 8% ethanol-eluted fraction showed highest activity against alpha-glucosidase with IC50 of 8.84 mg/mL, while 25% ethanol-eluted fraction possessed excellent antioxidant ability.

计算层状介质中电磁场的层矩阵法

As an important branch of electrical prospecting method, the artificial source frequency domain electromagnetism method has received more and more attention. But when conducts the fundamental research, people often isolated study some concrete method, so the research results of one method are very difficult to apply to another method directly. This article will possess the artificial source frequency domain EM method to an 1D model simply. It is stratified medium model, with an electric or magnetic source in or outside of it. Then take the horizontal electric dipole source as an example to introduce how to computing the EM field in stratified medium. Because layer matrix is the key of establishing equations, so we call it the layer-matrix method. The key of layer-matrix method is establishing equations by using layer matrixes in wavenumber(kx, ky, z) domain, then obtains the electromagnetic field value of wavenumber domain. After Fourier transform, we can get electromagnetic field of any position in spatial domain. The layer matrix technique theoretically can calculate electromagnetic field of any position for any source, is suitable for many kinds of electromagnetic method. After introduction of the layer matrix method, this article has done some CSAMT, MCSEM and Wireless Electro-Magnetic Method (WEM) modeling with layer matrix method separately. In CSAMT modeling, we get electromagnetic field dissemination characteristics considering wave number of the air, and obtain three-dimensional distribution characteristics of the electromagnetic field. In MCSEM modeling, we get electromagnetic field dissemination characteristics with and without considering the airwave, and obtain three-dimensional distribution characteristics of electromagnetic field. In WEM modeling, we get electromagnetic field’s difference between considering the ionosphere and not considering it, and recognize the ionosphere’s influence of electromagnetic field. With the layer matrix technique, we have got some new understandings of EM dissemination rules of different situations. All analysis results indicate that the layer-matrix technique is credible and effective, and are worthy of further thorough research and development.

中强地震震源的破裂过程

With the large developments of the seismic sources theory, computing technologies and survey instruments, we can model and rebuild the rupture process of earthquakes more realistically. On which earthquake sources' properties and tectonic activities law are realized more clearly. The researches in this domain have been done in this paper as follows. Based on the generalized ray method, expressions for displacement on the surface of a half-space due to an arbitrary oriented shear and tensile dislocation are also obtained. Kinematically, fault-normal motion is equivalent to tensile faulting. There is some evidence that such motion occurs in many earthquakes. The expressions for static displacements on the surface of a layered half-space due to static point moment tensor source are given in terms of the generalized reflection and transmission coefficient matrix method. The validity and precision of the new method is illustrated by comparing the consistency of our results with the analytical solution given by Okada's code employing same point source and homogenous half-space model. The computed vertical ground displacement using the moment tensor solution of the Lanchang_Gengma earthquake displays considerable difference with that of a double couple component .The effect of a soft layer at the top of the homogenous half-space on a shallow normal-faulting earthquake is also analyzed. Our results show that more seismic information would be obtained utilizing seismic moment tensor source and layered half-space model. The rupture process of 1999 Chi-Chi, Taiwan, earthquake investigated by using co-seismic surface displacement GPS observations and far field P-wave records. In according to the tectonic analysis and distributions of aftershock, we introduce a three-segment bending fault planes into our model. Both elastic half-space models and layered-earth models to invert the distribution of co-seismic slip along the Chi-Chi earthquake rupture. The results indicate that the shear slip model can not fit horizontal and vertical co-seismic displacements together, unless we add the fault-normal motion (tensile component) in inversions. And then, the Chi Chi earthquake rupture process was obtained by inversion using the seismograms and GPS observations. Fault normal motions determined by inversion, concentrate on the shallow northern bending fault from Fengyuan to Shuangji where the surface earthquake ruptures reveal more complexity and the developed flexural slip folding structures than the other portions of the rupture zone For understanding the perturbation of surface displacements caused by near-surface complex structures, We have taken a numeric test to synthesize and inverse the surface displacements for a pop-up structure that is composed of a main thrust and a back thrust. Our result indicates that the pop-up structure, the typical shallow complex rupture that occurred in the northern bending fault zone form Fengyuan to Shuangji, can be modeled better by a thrust fault added negative tensile component than by a simple thrust fault. We interpret the negative tensile distributions, that concentrate on the shallow northern bending fault from Fengyuan to Shuangji, as a the synthetic effect including the complexities of property and geometry of rupture. The earthquake rupture process also reveal the more spatial and temporal complexities form Fenyuan to SHuangji. According to the three-components teleseismic records, the S-wave velocity structure beneath the 59 teleseismic stations of Taiwan obtained by using the transform function method and the SA techniques. The integrated results, the 3D crustal structure of Taiwan reveal that the thickest part of crustal local in the western Central Range. This conclusion is consistent with the result form the Bouguer gravity anomaly. The orogenic evolution of Taiwan is young period, and the developing foot of Central Range dose not in static balancing. The crustal of Taiwan stays in the course of dynamic equilibrium. The rupture process of 2003)2,24,Jiashi, Xinjiang earthquake was estimated by the finite fault model using far field broadband P wave records of CDSN and IRIS. The results indicate that the earthquake focal is north dip trust fault including some left-lateral strike slip. The focal mechanism of this earthquake is different form that of earthquakes occurred in 1997 and 1998, but similar to that of 1996, Artux, Xinjiang earthquake. We interpreted that the earthquake caused trust fault due to the Tarim basin pushing northward and orogeny of Tianshan mountain. In the end, give a brief of future research subject: Building the Real Time Distribute System for rupture process of Large Earthquakes Based on Internet.

各向异性与非线性介质中弹性波场传播特征研究

The topic of this study is about the propagation features of elastic waves in the anisotropic and nonlinear media by numerical methods with high accuracy and stability. The main achievements of this paper are as followings: Firstly, basing on the third order elastic energy formula, principle of energy conservation and circumvolved matrix method, we firstly reported the equations of non-linear elastic waves with two dimensions and three components in VTI media. Secondly, several conclusions about some numerical methods have been obtained in this paper. Namely, the minimum suitable sample stepth in space is about 1/8-1/12 of the main wavelength in order to distinctly reduce the numerical dispersion resulted from the numerical mehtod, at the same time, the higher order conventional finite difference (CFD) schemes will give little contribution to avoid the numerical solutions error accumulating with time. To get the similar accuracy with the fourth order center finite difference method, the half truncation length of SFFT should be no less than 7. The FDFCT method can present with the numerical solutions without obvious dispersion when the paprameters of FCT is suitable (we think they should be in the scope from 0.0001 to 0.07). Fortunately, the NADM method not only can reported us with the higher order accuracy solutions (higher than that of the fourth order finite difference method and lower than that of the sixth order finite difference method), but also can distinctly reduce the numerical dispersion. Thirdly, basing on the numerial and theoretical analysis, we reported such nonlinear response accumulating with time as waveform aberration, harmonic generation and resonant peak shift shown by the propagation of one- and two-dimensional non-linear elasticwaves in this paper. And then, we drew the conclusion that these nonlinear responses are controlled by the product between nonlinear strength (SN) and the amplitude of the source. At last, the modified FDFCT numerical method presented by this paper is used to model the two-dimensional non-linear elastic waves propagating in VTI media. Subsequently, the wavelet analysis and polarization are adopted to investigate and understand the numerical results. And then, we found the following principles (attention: the nonlinear strength presented by this paper is weak, the thickness of the -nonlinear media is thin (200m), the initial energy of the source is weak and the anisotropy of the media is weak too): The non-linear response shown by the elastic waves in VTI media is anisotropic too; The instantaneous main frequency sections of seismic records resulted from the media with a non-linear layer have about 1/4 to 1/2 changes of the initial main frequency of source with that resulted from the media without non-linear layer; The responses shown by the elasic waves about the anisotropy and nonlinearity have obvious mutual reformation, namely, the non-linear response will be stronger in some directions because of the anisotropy and the anisotropic strength shown by the elastic waves will be stronger when the media is nonlinear.

Theory for determining alignment parameters of symmetric top molecule using (n+1) LIF

Expressions used for extracting the population and alignment parameters of a symmetric top molecule from (n + 1) laser-induced fluorescence (LIF) are derived by employing the tensor density matrix method. The molecular population and alignment are described by molecular state multipoles. The LIF intensity is a complex function of the initial molecular state multipoles, the dynamic factors, and the excitation-detection geometrical factors. The problem of how to extract the initial molecular state multipoles from (2 + 1) LIF, as an example, is discussed in detail. (C) 2000 American Institute of Physics. [S0021-9606(00)30744-9].

Stress transfer and damage evolution simulations of fiber-reinforced polymer-matrix composites

The stress transfer from broken fibers to unbroken fibers in fiber-reinforced thermosetting polymer-matrix composites and thermoplastic polymer-matrix composites was studied using a detailed finite element model. In order to check the validity of this approach, an epoxy-matrix monolayer composite was used as thermosetting polymer-matrix composite and a polypropylene (PP)-matrix monolayer composite was used as thermoplastic polymer-matrix composite, respectively. It is found that the stress concentrations near the broken fiber element cause damage to the neighboring epoxy matrix prior to the breakage of other fibers, whereas in the case of PP-matrix composites the fibers nearest to the broken fiber break prior to the PP matrix damage, because the PP matrix around the broken fiber element yields. In order to simulate composite damage evolution, a Monte Carlo technique based on a finite element method has been developed in the paper. The finite element code coupled with statistical model of fiber strength specifically written for this problem was used to determine the stress redistribution. Five hundred samples of numerical simulation were carried out to obtain statistical deformation and failure process of composites with fixed fiber volume fraction.

Study on the energy transfer between UO22+ and Eu3+ in sol-gel derived titania matrix by luminescence spectroscopy

The TiO2 gel doped with UO22+ and Eu3+ has been prepared by a sol-gel method. The quenching of the UO22+ emission by Eu3+ and the energy transfer from the excited state of UO22+ to the ground state oh Eu3+ have been investigated. The energy transfer has been studied by the measurement of luminescence lifetime tau, calculations of energy transfer efficiency eta(ET) and energy transfer rate W-ET The experimental results indicated that the quenching is combined static and dynamic mechanism, but the static mechanism is dominant.

Iterative method using consistent mass matrix in axisymmetrical finite element analysis of hypervelocity impact

We present in this paper an iterative method using consistent mass matrix in axisymmetrical finite element analysis of hypervelocity impact. To retain the advantage of integration on an element-by-element basis which is at the heart of modern hydrocodes, we suggest that the first step should be to solve for accelerations at an advanced time step by using the lumped mass approach, then iterate using a consistent mass matrix to improve the estimate. Examples are given to show the improved resolution with the new method.