Determination Ofinterfacial Mechanical Parameters For An Al/Epoxy/Al2O3 System Byusing Peel Test Simulations

Peel test measurements and simulations of the interfacial mechanical parameters for the Al/Epoxy/Al2O3 system are performed in the present investigation. A series of Al film thicknesses between 20 and 250 microns and three peel angles of 90, 135 and 180 degrees are considered. Two types of epoxy adhesives are adopted to obtain both strong and weak interface adhesions. A finite element model with cohesive zone elements is used to identify the interfacial parameters and simulate the peel test process. By simulating and recording normal stress near the crack tip, the separation strength is obtained. Furthermore, the cohesive energy is identified by comparing the simulated steady-state peel force and the experimental result. It is found from the research that both the cohesive energy and the separation strength can be taken as the intrinsic interfacial parameters which are dependent on the thickness of the adhesive layer and independent of the film thickness and peel angle.

Effect of quasicrystalline phase on the deformation behavior of Zr62Al9.5Ni9.5Cu14Nb5 bulk metallic glass

Quasicrystalline phase with different volume fraction were formed by isothermally annealing the as-castZr(62)Al(9.5)Ni(9.5)Cu(14)Nb(5) bulk metallic glass at 723 K for different times. The effects of quasicrystals on the deformation behavior of the materials were studied by nanoindentation and compression test. It revealed that the alloys with homogeneous amorphous structure exhibit pronounced flow serrations during the nanoindentation loading, while no obvious flow serration is observed for the sample with quasicrystals more than 10 vol.%. However, further compression tests confirm that the no-serrated flows are formed due to different reasons. For annealed samples containing quasicrystals less than 35 vol.%, continuous plastic deformation occurs due to propagation of multiple shear bands. While the disappearance of serrated flow cannot be explained by the generation of multiple shear bands for samples containing quasicrystals more than 35 vol.%, which will fracture with a totally different fracture mode, namely, dimple fracture mode under loading instead of shear fracture mode. (c) 2005 Published by Elsevier B.V.

溶液热历史对蛋白质晶体生长影响的内在原因研究

从溶液中聚集体的角度研究了溶液的热历史改变生长出的蛋白质晶体的数目和尺寸的内在原因.将在281和309 K下保存1 d的两组溶菌酶溶液按不同比例混合,加入沉淀剂生长晶体.随着高温溶液的比例增加,生长出的晶体数目减少,同时溶液中生长基元的尺寸增大.在5周内,采用动态光散射对281,293和309K三种温度下保存的溶菌酶溶液中聚集体的变化情况进行监测,发现溶液中均存在大小不同的两部分聚集体,称之为小聚集体与多聚体.前者的尺寸基本不随保存时间而变化,而后者尺寸随保存时间增加而减小,减小的速度与保存温度有关.多聚体的尺寸经过5周后和小聚集体基本相同.研究结果表明,处于无序聚集阶段的溶液的均一化程度和成核阶段生长基元的尺寸受到了溶液热历史的影响,并最终对晶体的数目产生影响.

Welding of Al alloy plates using a novel high-average-power pulsed CO2 laser

A novel high-average-power pulsed CO2 laser with a unique electrode structure is presented. The operation of a 5-kW transverse-flow CO2 laser with the preionized pulse-train switched technique results in pulsation of the laser power, and the average laser power is about 5 kW. The characteristic of this technique is switching the preionized pulses into pulse trains so as to use the small preionized power (hundreds of watts) to control the large main-discharge power (tens of kilowatts). By this means, the cost and the complexity of the power supply are greatly reduced. The welding of LF2, LF21, LD2, and LY12 aluminum alloy plates has been successfully achieved using this laser. (c) 2005 Society of Photo-Optical Instrumentation Engineers.

Welding of Al alloy plates using a novel high-average-power pulsed CO2 laser

A novel high-average-power pulsed CO2 laser with a unique electrode structure is presented. The operation of a 5-kW transverse-flow CO2 laser with the preionized pulse-train switched technique results in pulsation of the laser power, and the average laser power is about 5 kW. The characteristic of this technique is switching the preionized pulses into pulse trains so as to use the small preionized power (hundreds of watts) to control the large main-discharge power (tens of kilowatts). By this means, the cost and the complexity of the power supply are greatly reduced. The welding of LF2, LF21, LD2, and LY12 aluminum alloy plates has been successfully achieved using this laser. (c) 2005 Society of Photo-Optical Instrumentation Engineers.

Epitaxial Growth of AlInGaN Quaternary Alloys by RF-MBE

AlInGaN quaternary alloys were successfully grown on sapphire substrate by radio-frequency plasma-excited molecular beam epitaxy (RF-MBE). AlInGaN quaternary alloys with different compositions were acquired by changing the Al cell's temperature. The streaky RHEED patterns were observed during AlInGaN quaternary alloys growth. Scanning Electron Microscope (SEM), Rutherford back-scattering spectrometry (RBS), X-Ray diffraction (XRD) and Cathodoluminescence (CL) were used to characterize the structural and optical properties of the AlInGaN alloys. The experimental results show that the AlInGaN quaternary alloys grow on the GaN buffer in the layer-by-layer growth mode. When the Al cell's temperature is 920 degrees C, the Al/In ratio in the AlInGaN quaternary alloys is about 4.7, and the AlInGaN can acquire better crystal and optical quality. The X-ray and CL full-width at half-maximum (FWHM) of the AlInGaN are 5arcmin and 25nm, respectively.

Temperature dependence of the formation of nano-scale indium clusters in InAlGaN alloys on Si(111) substrates

The temperature dependence of the formation of nano-scale indium clusters in InAlGaN quaternary alloys, which are grown by metalorganic chemical vapour deposition on GaN/Si(111) epilayers, is investigated. Firm evidence is provided to support the existence of phase separation, or nano-scale In-rich clusters, by the combined results of high-resolution transmission electron microscopy (HRTEM), high-resolution x-ray diffraction (HRXRD) and micro-Raman spectra. The results of HRXRD and Raman spectra indicate that the degree of phase separation is strong and the number of In clusters in the InAlGaN layers on silicon substrate is higher at lower growth temperatures than that at higher growth temperatures, which limits the In and Al incorporated into the InAlGaN quaternary alloys. The detailed mechanism of luminescence in this system is studied by low temperature photoluminescence (LT-PL). We conclude that the ultraviolet (UV) emission observed in the quaternary InAlGaN alloys arises from the matrix of a random alloy, and the second emission peak in the blue-green region results from the nano-scale indium clusters.

A study of the growth and optical properties of AlInGaN alloys

We have studied the growth and optical properties of AlInGaN alloys in this article. By the measurement of three samples, we found that the incorporation of In decreases with the increase of temperature, while there is nearly no change for the incorporation of Al. The sample grown at the lowest temperature had the best material and optical properties, which owes to the high In component, because the In component can reduce defects and improve the material quality. We also used the time-resolved photoluminescence(PL) to study the mechanism of recombination of carriers, and found that the time dependence of PL intensity was not in exponential decay, but in stretched-exponential decay. Through the study of the character of this decay, we come to the conclusion that the emission comes from the recombination of localized excitons. Once more, this localization exhibites the character of quantum dots, and the stretched, exponential decay results from the hopping of carriers between different localized states. In addition, we have used the relation of emission energy dependence of carrier's lifetime and the character of radiative recombination and non-radiative combination to confirm our conclusion.

Thermal redistribution of localized excitons and its effect on the luminescence band in InGaN ternary alloys

Temperature-dependent photoluminescence measurements have been carried out in zinc-blende InGaN epilayers grown on GaAs substrates by metalorganic vapor-phase epitaxy. An anomalous temperature dependence of the peak position of the luminescence band was observed. Considering thermal activation and the transfer of excitons localized at different potential minima, we employed a model to explain the observed behavior. A good agreement between the theory and the experiment is achieved. At high temperatures, the model can be approximated to the band-tail-state emission model proposed by Eliseev et al. [Appl. Phys. Lett. 71, 569 (1997)]. (C) 2001 American Institute of Physics.

钠原子激光增强电离光谱研究—以石墨杯为原子化器 原子吸收光谱法对发样中Zn、Cu、Mn、Ap的测定

、I钠原子激光增强电离光谱(LEIS)方法的研究-以石墨杯为原子化器在LEIS方法中，最常见的原子化器是火焰。但由于火焰背景噪声严重且难以克服，在火焰原子化过程中，雾化和热离解不充分，仅有10~(-2)%的分析溶液参与吸收以及火焰气体使测定元素受到高度稀释等不利因素的影响，火焰原子化限制了LEIS方法灵敏度的进一步提高。考虑到石墨炉原子化器较火焰具有取样量少，绝对灵敏度高；样品（包括固态、液态）可直接引入石墨炉内；不会发生如同火焰中所存在的干扰效应；蒸发效率和原子化效率较高，几乎全部样品都能参与吸收等优点，本工作在已建立火焰LEIS方法的实验基础上，将原子化器改换为石墨杯进行了钠原子LEIS方法的研究。到目前为止，国内外仅有的几篇有关石黑炉LEIS的研究报告中，都报导了该方法对钠原子的检出限估计可达到10~(-14)-10~(-15)克，由于此项研究尚处于探索性研究阶段，故有关方法性的系统研究几乎还未见报导。本工作在未使用任何放大器的情况下（实验条件限制）对影响钠原子LEIS信号强度的诸因互进行了实验观察。主要包括：钠原子化条件；激光束位置、阳极电压、激光输出能量、电极位置以及激光脉冲重复率对LEIS信号强度的影响等。并绘制了校准曲线，统计方法的相对标准偏差分别为11%（高浓度）18.2%（低浓度），在现有仪器条件下，还不能测出检出限，测定下限为3*10~(-9)克。对固体粉末直接进行了尝试，检测下限为5*10~(-8)克，进样是为5毫克。在进一步的研究工作中，如有条件使用低噪声的放大器及Bxear积分器，选择门检时间窗，或采用分步激发等手段，估计本方法定会达到预想的高灵敏度，检敏度至少提高了个数量级。对石墨炉原子化LEIS法来说，似比较详细的研究报告，截至实验停止时还未见报导。II原子吸收光谱法对发样中Zn、Cu、Mn、Al的测定发中微量元素ZN、Cu、Mn均属人体必需元素，与人体的生长发育和多种生理功能，临床医学等方面有着极为密切的关系，而Al则被认为是异致某种疾病的元素之一。本工作报告了用火焰法测定Zn、Cu；石墨炉法测定Al、Mn的结果，其中，对Al的测定，为摆脱基体干扰，加入改进剂Mg(NO_3)_2，并采用平台石墨炉进行试验，得到了线性较好的工作曲线，但在实际测定时，由于实验条件的限制，只能采用一般石墨管加基体改进剂对少娄样品中Al含量进行测定。Zn、Cu、Al三种元素由标准曲线法测定；而Mn由于Fe的干扰无法消除而采用标准加入法测定，并因此限制了测定样品数。Cu、ZN、Mn三种元素的回收率分别为102.8%, 99.7%, 102.5%，变异系数为9.6%, 11.3%, 9.7%，对本地居民发中（30个发样）Zn、Cu含量进行测定，Zn、Cu的含量范围为148-318ppm，7.2-15ppm，并计算了Zn/Cu比。本方法对发样中四种元素的测定结果与ICP法进行对照。两种方法测定结果吻合得较好。

Deep electron states in n-type Al-doped ZnS1-xTex grown by molecular beam epitaxy

Capacitance-voltage, photoluminescence (PL), and deep level transient spectroscopy techniques were used to investigate deep electron states in n-type Al-doped ZnS1-xTex epilayers grown by molecular beam epitaxy. The integrated intensity of the PL spectra obtained from Al-doped ZnS0.977Te0.023 is lower than that of undoped ZnS0.977Te0.023, indicating that some of the Al atoms form nonradiative deep traps. Deep level transient Fourier spectroscopy (DLTFS) spectra of the Al-doped ZnS1-xTex (x=0, 0.017, 0.04, and 0.046, respectively) epilayers reveal that Al doping leads to the formation of two electron traps 0.21 and 0.39 eV below the conduction band. DLTFS results suggest that in addition to the roles of Te as a component of the alloy as well as isoelectronic centers, Te is also involved in the formation of an electron trap, whose energy level with respect to the conduction band decreases as Te composition increases. Our results show that only a small fraction of Al atoms forms nonradiative deep defects, indicating clearly that Al is indeed a very good donor impurity for ZnS1-xTex epilayers in the range of Te composition being studied in this work. (C) 1997 American Institute of Physics. [S0021-8979(97)08421-1].

Electronic properties of zinc-blende GaN, AlN, and their alloys Ga1-xAlxN

The electronic properties of wide-energy gap zinc-blende structure GaN, A1N, and their alloys Ga(1-x)A1(x)N are investigated using the empirical pseudopotential method. Electron and hole effective mass parameters, hydrostatic and shear deformation potential constants of the valence band at Gamma and those of the conduction band at Gamma and X are obtained for GaN and AIN, respectively. The energies of Gamma, X, L conduction valleys of Ga(1-x)A1(x)N alloy versus Al fraction x are also calculated. The information will be useful for the design of lattice mismatched heterostructure optoelectronic devices based on these materials in the blue light range application. (C) 1995 American Institute of Physics.

Band structure parameters of zinc-blende GaN, AlN and their alloys Ga1-xAlxN

The electronic properties of wide energy gap zinc-blende structure GaN, AlN and their alloys Ga1-xAlxN are investigated using the empirical pseudopotential method. Electron and hole Effective mass parameters, hydrostatic and shear deformation potential constants of the valence band at Gamma and those of the conduction band at Gamma and X are obtained. The energies of Gamma, X, L conduction valleys of Ga1-xAlxN alloy versus Al fraction x are also calculated. The information will be useful for the design of lattice mismatched heterostructure optoelectronic devices in the blue light range.