Characterization of parasitics in TO-packaged high-speed laser modules

An elaborate analysis of the parasitic network of high-speed through-hole packaging (TO)-type laser modules is presented using a small-signal equivalent circuit model. The intrinsic laser diode is obtained using the optical modulation technique, and is embedded into the model as a separate component. Three step-by-step measurements are made for determining the packaging parasitic network, including the test fixture, TO header, submount, bonding wire, and parasitics of the laser chip. A good agreement between simulated and measured results confirms the validation and accuracy of the characterization procedures. Furthermore, several key parasitic elements are found based on the simulation of the high-frequency responses of the packaged devices. It is expected that the 3-dB bandwidth of 12 GHz or more of the low-cost TO packaged laser module may be achieved using the proposed optimization method.

Potential frequency bandwidth estimation of TO packaging techniques for photodiode modules

Scattering parameters of photodiode chip, TO header and TO packaged module are measured, and the effects of TO packaging network on the high-frequency response of photodiode are investigated. Based on the analysis, the potential bandwidth of TO packaging techniques is estimated from the scattering parameters of the TO packaging network. Another method for estimating the potential bandwidth from the equivalent circuit for the TO packaged photodiode model is also presented. The results obtained using both methods show that the TO packaging techniques used in the experiments can potentially achieve a frequency bandwidth of 22 GHz.

A novel image restoration algorithm based on high-dimensional space geometry

A novel image restoration approach based on high-dimensional space geometry is proposed, which is quite different from the existing traditional image restoration techniques. It is based on the homeomorphisms and "Principle of Homology Continuity" (PHC), an image is mapped to a point in high-dimensional space. Begin with the original blurred image, we get two further blurred images, then the restored image can be obtained through the regressive curve derived from the three points which are mapped form the images. Experiments have proved the availability of this "blurred-blurred-restored" algorithm, and the comparison with the classical Wiener Filter approach is presented in final.

High-speed and high-power 1.3 mu m InGaAsP/InP selective proton-bombarded buried crescent lasers with optical field attenuation regions

High-speed and high-power InGaAsP/lnP selective proton-bombarded buried crescent (SPB-BC) lasers with optical field attenuation regions were reported. The defect of proton bombardment can not affect the lifetime of the SPB-BC laser because the optical field attenuation region obstructs the growth and propagation of defects. A CW light output over 115 mW was achieved at room temperature using a 500 mu m long cavity SPB-BC laser. The 3 dB bandwidth was 8.5 GHz, and the lifetime was about 8.5 x 10(5) h. The capacitance of four kinds of current blocking structures was first measured in our experiment, and the results shown that the capacitance of proton-bombarded pnpn structure was not only less than that of pnpn current blocking structure, but also less than that of semi-insulating Fe-InP structure.

Color filter-less technology of LED back light for LCD-TV - art. no. 68410G

Back Light Unit (BLU) and Color Filter are the two key components for the perfect color display of Liquid Crystal Display (LCD) device. LCD can not light actively itself, so a form of illumination, Back Light Unit is needed for its display. The color filter which consists of RGB primary colors, is used to generate three basic colors for LCD display. Traditional CCFL back light source has several disadvantages, while LED back light technology makes LCD obtain quite higher display quality than the CCFL back light. LCD device based on LED back light owns promoted efficiency of display. Moreover it can generate color gamut above 100% of the NTSC specification. Especially, we put forward an idea of Color Filter-Less technology that we design a film which is patterned of red and green emitting phosphors, then make it be excited by a blue light LED panel we fabricate, for its special emitting mechanism, this film can emit RGB basic color, therefore replace the color filter of LCD device. This frame typically benefits for lighting uniformity and provide pretty high light utilization ratio. Also simplifies back light structure thus cut down the expenses.

High-performance multiplexed vibration sensor system based on fiber lasers - art. no. 683019

This paper describes a high-performance multiplexed vibration sensor system using fiber lasers. A serial vibration sensor array consists of four short cavity fiber lasers. The system employs a single, polarization-insensitive, unbalanced Michelson interferometer to translate individual laser wavelength shifts induced by vibration signals into interferometer phase shifts. A dense wavelength division demultiplexor (DWDM) with high channel isolation is inserted to demultiplex each laser signal as a wavelength filter. Finally, a digital phase demodulator based on the phase generated carrier technique is used to achieve high-resolution interrogation. Experimental results show that no observable crosstalk is measured on the output channels, and the minimal detectable acceleration of this system is similar to 200ng/root Hz at 250Hz, which is fundamentally limited by the frequency noise of the lasers.

High speed silicon optical switches based on carrier depletion - art. no. 67812D

The novel design of a silicon optical switch on the mechanism of a reverse p-n junction is proposed. The figuration of contact regions at slab waveguides and the ion implantation technology for creation of junctions are employed in the new design. The two-layer rib structure is helpful for reduction of optical absorption losses induced by metal and heavily-doped contact. And more, simulation results show that the index modulation efficiency of Mach-Zehnder interferometer enhances as the concentrations of dopants in junctions increase, while the trade-off of absorption loss is less than 3 dB/mu m. The phase shift reaches about 5 x 10(-4) pi/mu m at a reverse bias of 10V with the response time of about 0.2ns. The preliminary experimental results are presented. The frequency bandwidth of modulation operation can arrive in the range of GHz. However, heavily-doped contacts have an important effect on pulse response of these switches. While the contact region is not heavily-doped, that means metal electrodes have schottky contacts with p-n junctions, the operation bandwidth of the switch is limited to about 1GHz. For faster response, the heavily-doped contacts must be considered in the design.

Design of Low Power Multi-Standard Active-RC Filter for WLAN and DVB-H

In this paper, a low-power, highly linear, integrated, active-RC filter exhibiting a multi-standard (IEEE 802.11a/b/g and DVB-H) application and bandwidth (3MHz, 4MHz, 9.5MHz) is present. The filter exploits digitally-controlled polysilicon resister banks and an accurate automatic tuning scheme to account for process and temperature variations. The automatic frequency calibration scheme provides better than 3% corner frequency accuracy. The Butterworth filter is design for receiver (WLAN and DVB-H mode) and transmitter (WLAN mode). The filter dissipation is 3.4 mA in RX mode and 2.3 mA (only for one path) in TX mode from 2.85-V supply. The dissipation of calibration consumes 2mA. The circuit has been fabricated in a 0.35um 47-GHz SiGe BiCMOS technology, the receiver and transmitter occupy 0.28-mm(2) and 0.16-mm(2) (calibration circuit excluded), respectively.

Simulation and fabrication of the SiC-based clamped-clamped filter

In this paper, the SiC-based clamped-clamped filter was designed and fabricated. The filter was composed of two clamped-clamped beam micromechanical resonators coupled by a spring coupling beam. Structural geometries, including the length and width of the resonator beam and coupling beam, were optimized by simulation for high frequency and high Q, under the material properties of SiC. The vibrating modes for the designed filter structure were analyzed by finite element analysis (FEA) method. For the optimized structure, the geometries of resonator beams and coupling beams, as well as the coupling position, the SiC-based clamped-clamped filter was fabricated by surface micromaching technology.

A high-gain high-linearity wide-band low noise amplifier for terrestrial and cable receptions

This paper presents the design of a wide-band low-noise amplifier (LNA) implemented in a 0.35 mu m SiGe BiCMOS technology for cable (DVB-C) and terrestrial (DVB-T) tuner applications. The LNA utilizes current injection to achieve high linearity. Without using inductors, the LNA achieves 0.1-1GHz wide bandwidth and 18.8-dB gain with less than 1.4-dB gain variation. The noise figure(NF) of the wideband LNA is 5dB, its 1-dB compression point is -2dBm and IIP3 is 8dBm. The LNA dissipates 120mW power with a 5-V supply.

A novel image restoration algorithm based on high-dimensional space geometry

A novel image restoration approach based on high-dimensional space geometry is proposed, which is quite different from the existing traditional image restoration techniques. It is based on the homeomorphisms and "Principle of Homology Continuity" (PHC), an image is mapped to a point in high-dimensional space. Begin with the original blurred image, we get two further blurred images, then the restored image can be obtained through the regressive curve derived from the three points which are mapped form the images. Experiments have proved the availability of this "blurred-blurred-restored" algorithm, and the comparison with the classical Wiener Filter approach is presented in final.

Fabrication of low cost Si-based tunable high performance resonant cavity enhanced photodetectors

Low cost Si-based tunable InGaAs RCE photodetectors operating at 1.3similar to1.6 mum were fabricated using sol-gel bonding. A tuning range of 14.5 nm, a quantum efficiency of 44% at 1476 nm and a 3-dB bandwidth of 1.8 GHz were obtained.

Small-signal and large-signal performance test of high-speed optoelectronics devices

This paper presents measurement methods for determining the reflection coefficients and frequency responses of semiconductor laser diodes, photodiodes, and EA modulator chips. A novel method for determining the intrinsic frequency responses of laser diodes is also proposed, and applications of the developed measurement methods are discussed. We demonstrate the compensation of bonding wire on the capacitances of both the submount and the laser diode, and present a method for estimating the potential modulation bandwidth of TO packaging technique. Initial study on removing the effects of test fixture on large-signal performances of optoelectronic devices at high data rate is also given.

A Novel Geometric Algorithm for Blind Image Restoration Based on High-Dimensional Space

A novel geometric algorithm for blind image restoration is proposed in this paper, based on High-Dimensional Space Geometrical Informatics (HDSGI) theory. In this algorithm every image is considered as a point, and the location relationship of the points in high-dimensional space, i.e. the intrinsic relationship of images is analyzed. Then geometric technique of "blurring-blurring-deblurring" is adopted to get the deblurring images. Comparing with other existing algorithms like Wiener filter, super resolution image restoration etc., the experimental results show that the proposed algorithm could not only obtain better details of images but also reduces the computational complexity with less computing time. The novel algorithm probably shows a new direction for blind image restoration with promising perspective of applications.

Ultra-narrow dual-channel filter based on symmetrical sampled fibre Bragg grating

A kind of ultra-narrow dual-channel filter is proposed in principle and demonstrated experimentally. This filter is designed by means of two sampled fibre Bragg gratings (SFBGs), where one is periodic 0-pi sampling and the other is symmetrical spatial sampling. The former can create two stopbands in the transmission spectra and the latter can produce two ultra-riarrow passbands. Our filter has the 3-dB bandwidth of about 1 pm, whose value is two orders of magnitude less than the bandwidth of the traditional SFBG filters. The proposed filter has a merit that the channel spacing remains unchanged when tuning the filter.