Generation of sub-5 fs pulses through cascade of filamentation and hollow fiber compression

A pulse-compression scheme based on cascade of filamentation and hollow fiber has been demonstrated, Pulses with duration of sub-5 fs and energy of 0.2 mJ near 800 nm have been generated by compressing the similar to 40 fs pulses from a commercial laser system. This method is promising to generate near monocycle high energy pulses. [GRAPHICS] Measured autocorrelation curve of the final compressed pulses with duration of sub-5 fs (black solid) and the simulated autocorrelation curve of 4.6 fs pulse near 800 rim (red dash) (C) 2008 by Astro Ltd. Published exclusively by WILEY-VCH Verlag GmbH & Co. KGaA

Optimization of optical parametric chirped pulse amplification with different pump wavelengths

Optical parametric chirped pulse amplification with different pump wavelengths was investigated using LBO crystal, at signal central wavelength of 800 nm. According to our theoretical simulation, when pump wavelength is 492.5 nm, there is a maximal gain bandwidth of 190 nm. centered at 805 nm in optimal noncollinear angle using LBO. Presently, pump wavelength of 492.5 nm can be obtained from second harmonic generation of a Yb:Sr-5(PO4)(3)F laser. The broad gain bandwidth can completely support similar to 6 fs with a spectral centre of seed pulse at 800 nm. The deviation from optimal noncollinear angle can be compensated by accurately tuning crystal angle for phase matching. The gain spectrum with pump wavelength of 492.5 nm is much better than those with pump wavelengths of 400, 526.5 and 532 nm, at signal centre of 800 nm. (c) 2005 Elsevier B.V. All rights reserved.

Generation of 5 fs, 0.7 mJ pulses at 1 kHz through cascade filamentation

Two-cycle optical pulses with duration of 5 fs and energy of 0.7 mJ have been generated at 1 kHz by compressing the 38 fs laser pulses from a carrier-envelope phase (CEP) controlled Ti:sapphire laser system through a cascade filamentation compression technique. A simple and effective method is developed to suppress multiple filament formation and stabilize a single filament by inserting a soft aperture with an appropriate diameter into the driving laser beam prior to focusing, resulting in an excellent compressed beam quality. The good beam quality and potentially higher peak power make this ultrashort laser pulse source a significant tool for high-field physics applications. (C) 2007 Optical Society of America.

体布拉格光栅外腔半导体激光器光谱特性研究

用体布拉格光栅(VBG)作为反馈元件与瓦级半导体激光器(LD)以及快轴准直柱透镜构成一个可以将半导体激光器的工作波长稳定在体布拉格光栅布拉格波长处的外腔激光器。测量了体布拉格光栅外腔激光器的波长稳定性与其工作电流、热汇温度、激光束准直装置等因素的关系。分析了波长稳定效果与半导体激光器增益谱特性、外腔结构参量等因素的关系。研究表明,在相同的工作电流、热汇温度下,当准直柱透镜直径为0.4 mm时的波长稳定效果较好;在此情况下,当热汇温度控制在30 ℃,工作电流从0.5 A增加到1.5 A的测量范围内,以及当工

Compensation for self-focusing by use of cascade quadratic nonlinearity

We demonstrate theoretically and experimentally compensation for positive Kerr phase shifts with negative phases generated by cascade quadratic processes. Experiments show correction of small-scale self-focusing and whole-beam self-focusing in the spatial domain and self-phase modulation in the temporal domain. (C) 2001 Optical Society of America.

板条热容激光器的二维热特性

固体热容激光器（SSHCL）作为高功率固体激光器的一个重要发展方向,引起人们广泛关注。数值模拟激光介质板条在热容方式下工作的温度和应力分布是了解该类激光器工作特性的一种有效手段,采用平面应力近似法导出了半导体激光器抽运热容激光介质板的二维温度和应力分布公式,同时也对二维抽运光吸收密度、介质板温度分布和折射率变化进行了分析与讨论。数值计算的结果表明二维效应的温度分布和应力分布要比一维效应给出的分布更均匀。

千瓦级半导体抽运的固体热容板条激光器

报道了千瓦级激光二极管面阵抽运固体热容激光器的理论与实验研究, 分别采用Nd:YAG单板条和双板条串接的热容激光器, 利用热容激光器的理论计算模型计算了在一定的工作时间内激光输出特性, 并进行了实验验证。实验中采用的晶体尺寸均为59 mm×40 mm×4.5 mm, 对单板条进行抽运时平均功率大约为5.6 kW, 双板条串接时为11.2 kW, 重复频率为1 kHz, 占空比为20％。实验中观察了1 s的工作时间内脉冲能量输出的波动情况, 单板条时单脉冲能量输出最大为1.3 J, 在1 s后单脉冲能量输出

热畸变对单板条热容激光器输出的影响

开展了激光二极管(LD)抽运的全固态热容激光器的理论与实验研究, 数值模拟了在热容工作条件下侧面抽运的Nd:YAG板条激光器的热透镜效应, 分析了热透镜效应对激光输出的影响, 并进行了相应的实验论证。实验中采用的晶体尺寸为57 mm×40 mm×4 mm, 激光二极管阵列的抽运峰值功率为12 kW, 重复频率为1 kHz, 占空比为20%, 为了获得较高的增益, 将抽运光通过光学系统进行聚焦, 抽运光在晶体侧面的光斑大小为15 mm×57 mm。实验中观察了1 s内的脉冲能量输出的波动情况, 在开始工作的

Numerical research of heat generation in flashlamp-pumped Nd : glass disk amplifiers

The heat generation in a flashlamp-pumped Nd:glass disk amplifier is studied by the simulation of the whole pumping process, which is based on the ray-tracing method. The results of temperature rise distribution as well as gain distribution are presented. The evolution of heat generation in disk during the pumping process is discussed in detail. Some main factors related with the thermal effect, such as the quantum efficiency, fluorescence lifetime, and pulse duration, are investigated through studying the ratio of the heat generation to energy storage in the gain medium. The influence of each parameter on heat generation is studied carefully, and the results provide ways to decrease the heat generation during the pumping process. (c) 2005 Society of Photo-Optical Instrumentation Engineers.

锯齿形板条抽运结构的热效应数值比较

激光二极管抽运的全固态激光器中,除了激光介质的温度分布和热透镜效应以外,抽运、冷却结构对获得高光束质量、高功率激光输出至关重要。基于热传导方程,在相同的抽运功率和传导冷却边界条件下,对单侧面抽运锯齿形(zigzag)板条、单侧面键合锯齿形板条、部分抽运板条三种不同抽运结构的温度分布、热致应力、温度导致的折射率变化进行了详细的分析,并通过光线追迹方法,比较了光束在锯齿形面内和垂直于锯齿形面内的光程差,由光程差曲线分析了激光束的热透镜效应。对三种抽运结构的端面温度、端面变形和端面变形导致的光程差也进行了对比分