Low temperature preparation and fuel cell properties of rare earth doped barium cerate solid electrolytes

The solid electrolytes, BaCe(0.8)Ln(0.2)O(2.9) (Ln: Gd, Sm, Eu), were prepared by the sol-gel method. XRD indicated that a pure orthorhombic phase was formed at 900 degrees C. The synthesis temperature by the sol-gel method was about 600 degrees C: lower than the high temperature solid phase reaction method. The electrical conductivity and impedance spectra were measured and the conduction mechanism was studied. The grain-boundary resistance of the solid electrolyte could be reduced or eliminated by the sol-gel method. The conductivity of BaCe0.8Gd0.2O2.9 is 7.87 x 10(-2) S.cm(-1) at 800 degrees C. The open-circuit voltage of hydrogen-oxygen fuel cell using BaCe0.8Gd0.2O2.9 as electrolyte was near to 1 V and its maximum power density was 30 mW.cm(-2).

DEVELOPMENT OF CYLINDRICAL SECONDARY LITHIUM POLYANILINE BATTERIES

The cylindrical 'D'-size batteries were fabricated by polyaniline paste cathode and lithium foil anode sandwiched with microporous polypropylene separator. The electrolyte used was LiClO4 dissolved in a mixed solvent of propylene carbonate and dimethoxyethane. The results of charge/discharge curves, charge/discharge cycles, the short-circuit current, the open-circuit voltage storage and the change of discharge capacity with temperature, discharge current are reported.

A WOUND-TYPE LITHIUM POLYANILINE SECONDARY CELL

A wound-type cell with a polyaniline (PAn) positive electrode, a LiClO4-propylene carbonate (PC) electrolyte, and a lithium foil negative electrode has been constructed. The two electrodes are separated by a polypropylene separator. The PAn is deposited on carbon felt from a HClO4 solution containing aniline by galvanostatic or potentiostatic electrolysis. Using cyclic voltammetry charge/discharge cycles and charge/retention tests, the following results have been obtained: (i) reversibility of the charge/discharge reaction of the PAn electrode is very good; (ii) more than 50 charge/discharge cycles at 80% charge/discharge efficiency and 260 W h kg-1 discharge energy density can be achieved at 50 mA between 2 and 4 V; (iii) the open-circuit voltage and the capacity retention of the battery after storage at open-circuit for 60 days are 3.4 V and 33%, respectively.

Ethanol crossover phenomena and its influence on the performance of DEFC

In the present work, Nafion (R) membrane porosity changes were determined in aqueous ethanol solutions with different concentrations by weighing vacuum-dried and ethanol aqueous solution equilibrated membranes at room temperature. The ethanol crossover rate through Nafion (R)-115 membrane at different temperatures and different concentrations had been investigated in a fuel cell test apparatus by using membrane gets higher as ethanol solution gas chromatography analysis. The experimental results show that the swelling degree of Nafion (R) concentration increases. The ethanol crossover rate increases with ethanol concentration and temperature increment. The single direct ethanol fuel cell (DEFC) tests were carried out to investigate the effect of ethanol concentration on ethanol crossover and consequently, on the open circuit voltage and the cell performance of DEFC. It can be found that ethanol crossover presented a negative effect on the OCV and the cell performance of DEFC. It can also be found that an improved DEFC performance was obtained as temperature increased although the ethanol crossover rate increased with temperature increment. (c) 2005 Elsevier B.V. All rights reserved.

A novel PTFE-reinforced multilayer self-humidifying composite membrane for PEM fuel cells

A novel polytetrafluoroethylene (PTFE)-reinforced multilayer self-humidifying composite membrane is developed. The membrane is composed of Nafion-impregnated porous PTFE composite as the central layer and nanosized SiO2 supported Pt catalyst imbedded into Nafion as the two side layers. The proton exchange membrane (PEM) fuel cells employing the self-humidifying membrane (20 mu m thick) under dry H-2/O-2 gave a peak power density of 0.95 W/cm(2) and an open-circuit voltage of 1.032 V. The good membrane performance is attributed to hygroscopic Pt-SiO2 catalyst at the two side layers, which results in enhanced anode side self-humidification function and decreased cathode polarization. (c) 2005 The Electrochemical Society.

Potential frequency bandwidth estimation of TO packaging techniques for photodiode modules

Scattering parameters of photodiode chip, TO header and TO packaged module are measured, and the effects of TO packaging network on the high-frequency response of photodiode are investigated. Based on the analysis, the potential bandwidth of TO packaging techniques is estimated from the scattering parameters of the TO packaging network. Another method for estimating the potential bandwidth from the equivalent circuit for the TO packaged photodiode model is also presented. The results obtained using both methods show that the TO packaging techniques used in the experiments can potentially achieve a frequency bandwidth of 22 GHz.

Circuit design and simulation of a CMOS-based preamplifier for brain neural signals

A novel CMOS-based preamplifier for amplifying brain neural signal obtained by scalp electrodes in brain-computer interface (BCI) is presented in this paper. By means of constructing effective equivalent input circuit structure of the preamplifier, two capacitors of 5 pF are included to realize the DC suppression compared to conventional preamplifiers. Then this preamplifier is designed and simulated using the standard 0.6 mu m MOS process technology model parameters with a supply voltage of 5 volts. With differential input structures adopted, simulation results of the preamplifier show that the input impedance amounts to more than 2 Gohm with brain neural signal frequency of 0.5 Hz-100 Hz. The equivalent input noise voltage is 18 nV/Hz(1/2). The common mode rejection ratio (CMRR) of 112 dB and the open-loop differential gain of 90 dB are achieved.

Intercellular calcium wave propagation in linear and circuit-like bone cell networks

In the present study, the mechanism of intercellular calcium wave propagation in bone cell networks was identified. By using micro-contact printing and self-assembled monolayer technologies, two types of in vitro bone cell networks were constructed: open-ended linear chains and looped hexagonal networks with precisely controlled intercellular distances. Intracellular calcium responses of the cells were recorded and analysed when a single cell in the network was mechanically stimulated by nano-indentation. The looped cell network was shown to be more efficient than the linear pattern in transferring calcium signals from cell to cell. This phenomenon was further examined by pathway-inhibition studies. Intercellular calcium wave propagation was significantly impeded when extracellular adenosine triphosphate (ATP) in the medium was hydrolysed. Chemical uncoupling of gap junctions, however, did not significantly decrease the transferred distance of the calcium wave in the cell networks. Thus, it is extracellular ATP diffusion, rather than molecular transport through gap junctions, that dominantly mediates the transmission of mechanically elicited intercellular calcium waves in bone cells. The inhibition studies also demonstrated that the mechanical stimulation-induced calcium responses required extracellular calcium influx, whereas the ATP-elicited calcium wave relied on calcium release from the calcium store of the endoplasmic reticulum.

Preliminary study on a potential antibacterial peptide derived from histone H2A in hemocytes of scallop Chlamys farreri

Histone H2A is reported to participate in host defense response through producing novel antimicrobial peptides (AMPs) from its N-terminus in vertebrates and invertebrates, while the AMPs derived from H2A have not to our knowledge been reported in mollusca. In the present study, gene cloning, mRNA expression of H2A from scallop Chlamys farreri, and the recombinant expression of its N-terminus were conducted to investigate whether a similar mechanism exists in mollusca. The full-length DNA of H2A was identified by the techniques of homology cloning and genomic DNA walking, The full-length DNA of the scallop H2A was 696 bp long, including a 5'-terminal untranslated region (UTR) of 90 bp, a 3'-terminal UTR of 228 bp with a stem-loop structure and a canonical polyadenylation signal sequence AATAAA, and an open reading frame of 375 bp encoding a polypeptide of 125 amino acids. The mRNA expression of H2A in the hemocytes of scallop challenged by microbe was measured by semi-quantitative RT-PCR. The expression of H2A was not upregulated after stimulation, suggesting that H2A did not participate in immunity response directly. The DNA fragment of 117 bp encoding 39 amino acids corresponding to the N-terminus of scallop H2A, which was homologous to buforin I in vertebrates, was cloned into Pichia pastoris GS115. The transformants (His(+) Mut(+)) containing multi-copy gene insertion were selected with increasing concentration of antibiotic G418. The peptide of 39 amino acids was expressed by induction of 0.5% methanol. The recombinant product exerted antibacterial activity against both Gram-positive (G(+)) and Gram-negative (G(-)) bacteria. The antibacterial activity toward G(+) bacteria was 2.5 times more than that against G(-) bacteria. The results elucidated that N-terminus of H2A was a potential AMP and provided a promising candidate for a new antibiotic screening. However, whether H2A is really involved in scallop immune response mechanisms needs to be further investigated. (C) 2006 Elsevier Ltd. All rights reserved.