A comparison between TGT and Cz grown Nd : YAG

Large sized neodymium-doped Y3Al5O12 (Nd:YAG) laser crystals have been grown by temperature gradient technique (TGT) method and compared with Czochralski (Cz) method. The comparison of these two crystal growth methods has been listed. The results showed that the TGT method has many advantages over the Cz method. The concentration distribution of Nd ions in the crystals was determined and the absorption spectra of these crystals have been investigated and compared. The TGT grown highly doped Nd:YAG crystal has a larger absorption FWHM than that of Cz grown Nd:YAG crysral. Highly doped Nd:YAG (similar to 2.8 at. pct) crystals could be obtained by TGT.

温度梯度法生长Nd：YAG晶体的1200W激光输出

用温度梯度法（TGT）生长了大尺寸的Nd：YAG激光晶体，测试了室温下的吸收谱并利用吸收谱研究了Nd离子在YAG晶体中的分布。比较了温度梯度法与提拉法生长晶体的区别。根据热容激光的原理，利用生长的Nd：YAG激光晶体片设计了热容激光器，利用侧面抽运，获得了1200w的激光输出，工作时间为2s，光-光转换效率为30％。

国产Nd：YAG陶瓷获得激光输出

近年来Nd：YAG多晶陶瓷作为激光介质得到了越来越多的重视，我国在这个方向也开展了大量的研究工作，Nd：YAG多晶陶瓷与Nd：YAG单晶相比有很多优点：容易制造、成本低、可以制造大尺寸和高掺杂浓度的材料，且无浓度梯度，机械特性良好，硬度比单晶大1．5倍，断裂韧度比单晶大5倍，并且可制备多层和多功能的陶瓷结构、可大批量生产，已经获得了比Nd：YAG单晶更高的效率，因此钇铝石榴石透明陶瓷是理想的钇铝石榴石单晶激光介质材料替代品。但国产陶瓷由于质量不佳，透明度不是很高，一直未能获得激光输出。

Nd：YAG透明陶瓷的烧成及其显微结构

由溶胶一凝胶／燃烧合成结合法合成了Nd：YAG(掺钕钇铝石榴石，neodymium—doped yttrium aluminium garnet)粉体，用真空烧结法制备了Nd：YAG透明陶瓷。研究了显微结构随烧结温度和保温时间的变化，并对透明陶瓷的晶界结构和成分分布进行了表征。随着烧结温度的提高和保温时间的延长，Nd：YAG陶瓷的密度增大，晶形发育完整，透过率提高。晶粒内部和晶界的化学组成基本相同。所制备的Nd：YAG透明陶瓷在激光工作波长1064nm的透过率达到75％。

Optimization of thermal environment during crystal growth of large-sized Nd : YAG by Temperature Gradient Technique

A finite-element model is employed to analysis the thermal environments in Temperature Gradient Technique (TGT) furnace during the growth of large-sized Nd:YAG crystal. The obtained results show that when the crucible is located at the lower position inside of the heater, a flatter solid-liquid interface is established, which makes it easier to obtain the core-free Nd:YAG crystal. Meanwhile, the lower crucible position can induce higher axial temperature gradient, which is beneficial to the release of latent heat. (c) 2007 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Diode-pumped passively q-switched Nd : YAG ceramic laser with a Cr4+: YAG crystal-satiable absorber

Transparent polycrystalline Nd:YAG ceramics were fabricated by solid-state reactive sintering a mixture of commercial Al2O3,Y2O3, and Nd2O3 powders. The powders were mixed in ethanol and doped with 0.5 wt% tetraethoxysilane, dried, and pressed. Pressed samples were sintered at 1750 degrees C in vacuum. Transparent fully dense samples with average grain sizes of 10 mu m were obtained. The 1 at.% Nd:YAG ceramic was used to research passively Q-switched laser output with a Cr4+:YAG crystal as a saturable absorber. An average output power of 94 mW with a pulse width of 50 ns was obtained when the incident pump power was 750 mW. The slope efficiency was 13%. The pulse energy is 5 mu J, and the peak power is about 100 W.

温度梯度法生长Nd：YAG激光晶体的核心分布

用温度梯度法生长了直径为75mm大尺寸的Nd：YAG激光晶体，通过退火排除了生长过程中进入晶体的碳原子．用正交偏光显微镜观察了晶体的核心分布以及生长条纹．测试了室温下的吸收谱并利用吸收谱研究了Nd离子在YAG晶体中的分布．比较了温度梯度法与提拉法生长晶体的区别．

Damage on HfO2/SiO2 high-reflecting coatings under single and multiple Nd:YAG laser pulse irradiation

The single- and multi-shot damage behaviors of HfO2/SiO2 high-reflecting (HR) coatings under Nd:YAG laser exposure were investigated. Fundamental aspects of multi-shot laser damage, such as the instability due to pulse-to-pulse accumulation of absorption defect and structural defect effect, and the mechanism of laser induced defect generation, are considered. It was found in multi-shot damage, the main factors influencing laser-induced damage threshold (LIDT) are accumulation of irreversible changes of structural defects and thermal stress that induced by thermal density fluctuations.

Laser-induced damage of Ta2O5/S1O2 narrow-band interference filters under different 1064 nm Nd : YAG laser modes

The laser-induced damage (LID) behavior of narrow-band interference filters was investigated with a Nd:YAG laser at 1064 nm under single-pulse mode and free-running mode. The absorption measurement of such coatings was performed with surface thermal lensing (STL) technique. The damage morphologies under the two different laser modes were also studied in detail. It was found that all the filters exhibited a pass-band-center-dependent absorption and laser-induced damage threshold (LIDT) behavior, but the damage morphologies were diverse. The explanation was given with the analysis of the electric field distribution and the operational behavior of the irradiation laser. (c) 2005 Elsevier B.V. All rights reserved.

Nd：YAG激光器光栅式扫描预处理的计算模拟与优化分析

采用计算模拟的方法．研究了光栅式扫描预处理的扫描方式以及脉冲能量波动、定位误差对预处理效率的影响。研究发现。脉冲能量波动及其定位误差使预处理效率降低，同时其影响与扫描方式之间存在相互调制作用．因此可以通过选择合适的扫描方式以及扫描间隔来优化预处理流程，提高预处理效率。此外发现，光斑呈等边三角形排列时的预处理效率优于正方形。

A Diode-Side-Pumped Dynamic Fundamental Mode Nd:YAG Laser

A fundamental mode Nd YAG laser is experimentally demonstrated with a stagger pumped laser module and a special resonator. The rod is pumped symmetrically by staggered bar modules. A dynamic fundamental mode is achieved with the special resonator under different pump levels. A maximal continuous wave output of 61 W (M-2 = 1.4) is achieved with a single rod. An average output of 47 W, pulse width of 54 ns, pulse energy of 4.7 mJ and peak power of 87 kW are obtained under the Q-switched operation of 10 kHz.

Diode-end-pumped passively mode-locked ceramic Nd : YAG Laser with a semiconductor saturable mirror

We report on a diode- pumped CW passively mode locked ceramic Nd: YAG laser with SESAM ( semiconductor saturable absorber mirror), wavelength 1064nm. At a pump power of 7.6w, the pulse width was estimated to be similar to 8.3ps with repetition rate similar to 130MHz and the average output power was 1.59w. To our knowledge, this was the first demonstration that ceramic Nd: YAG was used for diode pumped CW passively mode locking. (C) 2005 Optical Society of America.

Q-switched and mode-locked diode-pumped Nd : YAG laser with an LT-GaAs

Simultaneous Q-switching and mode-locking (QML) is accomplished in a diode-pumped Nd:YAG laser using low-temperature GaAs (LT-GaAs) as the saturable absorber, which also acts as an output coupler at the same time. The repetition rate of the Q-switched envelope increased from 25 to 40 kHz as the pump power increased from 2.2 to 6.9 W. The mode-locked pulses inside the Q-switched pulse envelope had a repetition rate of 714 MHz. A maximum average output power of 770 mW was obtained. (c) 2005 Elsevier GmbH. All rights reserved.

A passively mode-locked diode-end-pumped Nd : YAG laser with a semiconductor saturable absorber mirror grown by metal organic chemical vapour deposition

We report the experimental results of a mode-locked diode-end-pumped Nd:YAG laser with a semiconductor saturable absorber mirror (SESAM) from which we achieved a 10 ps pulse duration at 150 MHz repetition rate. The SESAM was grown by metal organic chemical vapour deposition at low temperature. The recovery time was measured to be 0.5 ps, indicating the potential pulse compression to sub-picoseconds.

LD side-pumped high beam quality passive Q-switched and mode-locked Nd:YAG laser based on SESAM

We report a LD side-pumped fundamental-mode (Mx(2) = 1.35 and My(2) = 1.27) passive Q-switched and mode-locked Nd:YAG laser based on a semiconductor saturable absorber mirror (SESAM). At a pump current of 12.5 A, the average output power of 5.68 W with 80 kHz repetition rate and 2 mu s pulse width of the Q-switched envelope was generated. The repetition rate of the mode-locked pulse within the Q-switched envelope of 88 MHz was achieved.