镍系稀土钙钛矿型复合氧化物及其相关结构催化剂上的氨氧化

通过对La_(1-x)Sr_xNiO_(3-λ)，La_(1-4/3x)Th_xNiO_(3-λ)，La_(2-x)Sr_xNiO_(4+λ)三个系列催化剂上氨氧化的研究，提出如下结论：即Ni~(3+)为三系列催化剂的活性离子，晶格氧（O~=）为氨氧化的主要活性氧种。在LaNiO_(3-λ)中，氧缺陷已达到有序化，掺入Sr~(2+)后，在X ≤ 0.3含量减少，活性下降。在La_(1-4/3X)Th_xNiO_(3-λ)中，由于始终存在1/3X的阳离子缺陷，所以在X ≤ 0.3内，即在保持钙钛矿结构不变的范围内，使氧缺陷有序化结构得到破坏，变为无序的点缺陷，提高了Ni~(3+)的含量，从而也提高了催化活性。由于La_2NiO_4相在高温区较LaNiO_3稳定，所以以LaNiO_3中掺入杂质高于较易使钙钛矿结构发生分解，变成La_2NiO_4等相。La_(0.9)Sr_(0.1)NiO_63在≥950 ℃时便会发生这种反应。La_2NiO_(4+λ)中掺入Sr~(2+)后，其结构不发生变化，但会发生一定程度的畸变，Ni~(3+)量随Sr~(2+)的掺入而提高，活笥也随之升高，在La_(2-x)Sr_xNiO_(4+λ)中阴，阳离子缺陷都存在，在 X = 0.5时，La_(1.5)Sr_(0.5)NiO_(4+λ)变为计量化合物，La_(1.5)Sr_(0.5)NiO_(4.00)。三系列催化剂的活性物与电阻成反比，越不易被还原的催化剂活性越高。

Sr_3Ti_2O_7型稀土-钴氧化物的合成、结构和物理性质

自从发现高温超导含铜复合氧化物以来,人们的注意力便集中在以钙钛矿为基础的衍生物的研究上.Ruddlesden和Poper将其中的一类概括为Sr_(n+1)Ti_nO_(3n+1),其中n是钙钛矿层数,n个钙钛矿层又被1个SrO层隔开.事实上,La_2 CuO_4对应着n=1相,而La_(2-x)Sr_x CuO_4也具有相同的结构.通过用低价态的过渡金属离子置换Ti~(4+),同时用较高价态的离子置换

Ca、Sr掺杂的La_2NiO_4的电学性质

制备了一种新的固溶体La_(2-x)Ca_xNiO_4(0≤x≤1.4)并与固溶体La_(2-x)Sr_xNiO_4作了对比。它们都具有四方的K_2NiF_4结构,其晶胞参数和晶胞体积都随x的增加而减少。固溶体La_(2-x)Ca_xNiO_4的室温电阻率随x的增加而增加,而固溶体La_(2-x)Sr_xNiO_4的室温电阻率却随x增加而减小,这种电学性质上的差别可能是由于Sr或Ca掺杂后引起Ni的价态变化导致Ni~(3+)的电子构型转变而造成的。

Sol-gel synthesis and properties of Ce1-xGdxO2-x/2 solid solutions

A series of solid electrolytes Ce1-xGdxO2-x/2(x=0 similar to0.6) was prepared by sol-gel method. The structure, thermal expansion coefficient and electrical properties of the solid solutions were systematically studied. XRD data showed that a complete cubic fluorite structure was formed at 160 degreesC. The purity of the product prepared by the sol-gel method is higher, the grain size is uniformly smaller. They were easily sintered into highly dense ceramic pellets at 1 300 degreesC. The sintering temperature was significantly lower than that by traditionally high temperature solid phase reaction method. The thermal expansion coefficient of Ce0.8Gd0.2O1.9, determined from high- temperature XRD data, is 8. 125 X 10(-6) K-1. Impedance spectra analyses showed that the grain-boundary resistance of the solid electrolyte prepared by sol-gel method was reduced or even eliminated. The conductivity of Ce0.8Gd0.2O1.9 is 5.26 X 10(-3) S/cm at 600 degreesC. The activation energy (E-a) is 0.82 eV.

Eu~(2+)激活的两种新的发光基质的合成和性能研究

多铝酸盐体系是一类重要的发光基质,这类体系在可见区光学透明,耐热耐高温耐辐射,化学性质稳定,发光效率高,而且具有成为多功能材料的优越条件.因此,对这类体系的研究一直引起人们的重视.我们在研究稀土三基色发光材料的过程中,通过对角线规则和离子取代规则,得到了两种新的发光基质,可表示为Ba Li_(2-x)□_xAl_(10)O_(17)或BaLiAl_(10)O_(17-δ)(以下称为BLAO)和K_（0.5）La_（0.5）MgAl_(10)O_(17)(以下称为KLMAO),Eu~2+激活后产生450nm左右的蓝色发光,其发光性能可与BaMgAl_(10)O(17):Eu~（2+）相媲美,通过进一步研究,有可能应用到三基色发光材料中去.

锰含量对LiNi_(0.85-x)Co_(0.15)Mn_xO_2结构及形貌的影响

采用共沉淀法先合成出氢氧化物前驱体Ni0.85-xCo0.15Mnx(OH)2,其中X=0、0.1、0.2和0.4,前驱体与Li2CO3在空气气氛中固相烧结制得正极材料LiNi0.85-xCo0.15MnxO2。用XRD、SEM研究了锰含量对材料结构和形貌的影响。研究发现,LiNi0.85Co0.15O2的X射线衍射图中存在微量第二相,而锰掺杂有利于减小反应过程中锂离子损失和镍离子占据锂位,容易形成有序层状结构材料。随着Mn离子替代Ni离子量的增加,晶胞参数a减小,晶胞参数c、c/a及I003/I104值增大。SEM结果表明前驱体和最终产物形貌均随锰含量增加颗粒均匀性增强,粒子尺寸变小,粒径分布变窄。

Investigation on nonradiative decay of the (Er3+I13/2)-I-4 -> I-4(15/2) transition in different tellurite glass matrix

Three kinds of Er3+-doped tellurite glasses with different hydroxyl groups are prepared by the conventional melt-quenching method. Infrared spectra are measured to estimate the exact content of OH- groups in samples. The maximum phonon energy in glasses are obtained by measuring the Raman scattering spectra. The strength parameters Omega(t) (t = 2, 4, 6) for all the samples are calculated and compared. The nonradiative decay rate of the Er3+ I-4(13/2) -> I-4(15/2) transition are calculated for the glass samples with different phonon energy and OH- group contents. Finally, the effect of OH- groups on fluorescence decay rate of Er3+ is analysed, the constant KOH-Er Of TWN, TZPL and TZL glasses are calculated to be 9.2 x 10(-19) cm(4)s(-1), 5.9 x 10(-19) cm(4)s(-1), and 3.5 x 10(-19) cm(4)s(-1), respectively.

KMgF3及KMgF3：Eu^2＋晶体的射线辐照效应

KMgF3F Eu晶体中Eu^3＋→Eu^2＋的转换率在低浓度掺杂时接近100％，完全转换的饱和掺杂摩尔分数为0．29％．实验条件下，KMgF，晶体的X射线1h辐照损伤可在约100h后恢复；KMgF3：Eu^2＋晶体经X射线辐照后，360nm锐峰发射强度略有降低．不同剂量的γ射线辐照，KMgF3晶体热释光曲线的各个温度峰强度变化明显不同，即使小剂量辐照，造成的损伤也较难恢复，如γ射线辐照剂量为10^3Gy时，辐照损伤的恢复时间约需30d．KMgF3：Eu^2＋晶体360nm锐峰发射强度随γ射线辐照剂量增大

Growth and characterization of high-quality LiAlO2 single crystal

g-LiAlO2 single crystal is a promising substrate for GaN heteroepitaxy. In this paper, we present the growth of large-sized LiAlO2 crystal by modified Czochralski method. The crystal quality was characterized by high-resolution X-ray diffraction and chemical etching. The results show that the as-grown crystal has perfect quality with the full width at half maximum (FWHM) of 17.7-22.6 arcsec and etch pits density of (0.3-2.2) x 10(4) cm(-2) throughout the crystal boule. The bottom of the crystal boule shows the best quality. The optical transmission spectra from UV to IR exhibits that the crystal is transparent from 0.2 to 5.5 mu m and becomes completely absorbing around 6.7 mu m wavelength. The optical absorption edge in near UV region is about 191 nm.

Elevated levels of urinary 8-hydroxy-2'-deoxyguanosine in male electrical and electronic equipment dismantling workers exposed to high concentrations of polychlorinated dibenzo-p-dioxins and dibenzofurans, polybrominated diphenyl ethers, and polychlorinated biphenyls

To investigate the occupational exposure levels to polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), polybrominated diphenyl ethers (PBDEs), and polychlorinated biphenyls (PCBs), indoor dust (n = 3) in workshops and hair samples from male workers (n = 64) were collected at two electrical and electronic equipment waste (E-waste) dismantling factories located in the LQ area in east China in July 11-13, 2006. Pre- and postworkshift urines (64 of each) were also collected from the workers to study oxidative damage to DNA using 8-hydroxy-2'-deoxyguanosine (8-OHdG) as a biomarker. The concentrations of PCDD/Fs, PCDD/F-WHO-TEQs, PBDEs, PCBs and PCB-WHO-TEQs were (50.0 +/- 8.1) x 10(3), 724.1 +/- 249.6, (27.5 +/- 5.8) x 10(6), (1.6 +/- 0.4) x 10(9), (26.2 +/- 3.0) x 10(3) pg/g dry weight (dw) in dust, and (2.6 +/- 0.6) x 10(3), 42.4 +/- 9.3, (870.8 +/- 205.4) x 10(3), (1.6 +/- 0.2) x 10(6), 41.5 +/- 5.5 pg/g dw in hair, respectively. The homologue and congener profiles in the samples demonstrated that high concentrations of PCDD/Fs, PBDEs, and PCBs were originated from open burning of E-waste. The 8-OHdG levels were detected at 6.40 +/- 1.64 mu mol/mol creatinine in preworkshift urines. However, the levels significantly increased to 24.55 +/- 5.96 mu mol/mol creatinine in postworkshift urines (p < 0.05). Then, it is concluded that there is a high cancer risk originated from oxidative stress indicated by the elevated 8-OHdG levels in the E-waste dismantling workers exposed to high concentrations of PCDD/Fs, PBDEs, and PCBs.

超晶格结构的X射线衍射运动学理论模拟计算

Submitted by zhangdi (zhangdi@red.semi.ac.cn) on 2009-04-13T11:45:31Z

Rearrangeable nonblocking thermo-optic 4 x 4 switching matrix in silicon-on-insulator

A rearrangeable nonblocking thermo-optic 4 x 4 switching matrix is demonstrated. The matrix, which consists of five 2 x 2 multimode interference-based Mach-Zehnder interferometer (MMI-MZI) switch elements, is fabricated in silicon-on-insulator waveguide system. The average excess loss for the optical path experiencing 2 and 3 switch elements is 6.6 and 10.1 dB respectively. The crosstalk in the matrix is measured to be between -12 and -19 dB. The switching time of the device is less than 30 mu s.

X-ray diffraction analysis on gallium-indium interdiffusion in quantum dot superlattices

Thermal-induced interdiffusion in InAs/GaAs quantum dot superlattices is studied by high-resolution x-ray diffraction rocking curve and photoluminescence techniques. With increasing annealing temperatures, up to 300 meV a blueshift of the emission peak position and down to 16.6 meV a narrowing of the line width are found in the photoluminescence spectra, and respective intensity of the higher-order satellite peaks to lower-order ones in the x-ray rocking curves decreases. Dynamical theory is employed to simulate the measured x-ray diffraction data. Excellent agreement between the experimental curves and the simulations is achieved when the composition, thickness and stress variations caused by interdiffusion are taken into account. It is found that the significant In-Ga intermixing occurs even in the as-grown InAs/GaAs quantum dots. The estimated diffusion coefficient is 1.8 x 10(-17) cm(2) (.) s(-1) at 650 degreesC, 3.2 x 10(-17) cm(2 .) s(-1) at 750 degreesC, and 1.2 x 10(-14) cm(2 .) s(-1) at 850 degreesC.

First charge collection and position-precision data on the medium-resistivity silicon strip detectors before and after neutron irradiation up to 2x10(14) n/cm(2)

Test strip detectors of 125 mu m, 500 mu m, and 1 mm pitches with about 1 cm(2) areas have been made on medium-resistivity silicon wafers (1.3 and 2.7 k Ohm cm). Detectors of 500 mu m pitch have been tested for charge collection and position precision before and after neutron irradiation (up to 2 x 10(14) n/cm(2)) using 820 and 1030 nm laser lights with different beam-spot sizes. It has been found that for a bias of 250 V a strip detector made of 1.3 k Ohm cm (300 mu m thick) can be fully depleted before and after an irradiation of 2 x 10(14) n/cm(2). For a 500 mu m pitch strip detector made of 2.7 k Ohm cm tested with an 1030 nm laser light with 200 mu m spot size, the position reconstruction error is about 14 mu m before irradiation, and 17 mu m after about 1.7 x 10(13) n/cm(2) irradiation. We demonstrated in this work that medium resistivity silicon strip detectors can work just as well as the traditional high-resistivity ones, but with higher radiation tolerance. We also tested charge sharing and position reconstruction using a 1030 nm wavelength (300 mu m absorption length in Si at RT) laser, which provides a simulation of MIP particles in high-physics experiments in terms of charge collection and position reconstruction, (C) 1999 Elsevier Science B.V. All rights reserved.

催化消除NO_x复合氧化物催化剂的研究

氮的氧化物(NOx)是大气中的一种重要的污染物，是酸雨的主要来源，目前氮氧化物的无毒处理已经是国际环保研究中最关键的课题之一。本论文选择了两种复合氧化物：一种是钙钛石结构的含Cu的层状复合氧化物；另一种是以水滑石为前体经焙烧后得的复合氧化物为催化剂对它们的物化性质和对催化消除NOx的活性进行了系统的研究，得到了一些有意义的结果。第一部分：钙钛石型结构的含Cu层状复合氧化物钙钛石复合氧化物由于具有独特的物理化学性质，长期以来一直受到固态物理、固体化学和催化领域的科技工作者的重视。尤其近年来对它们在催化消除NOx反应中的活性的研究引起了催化工作者的极大兴趣，这是由于，一方面，钙钛石类复合氧化物对处理NOx的反应活性比较高，有希望取代贵金属催化剂；另一方面，探讨复合氧化物的固态物理、化学性质与处理NOx反应催化性能的关系，有利于揭示处理NOx反应的催化作用本质，为寻找高效实用的催化剂提供理论依据。本论文系统研究了三个系列含Cu钙钛石型复合氧化物的固态物理化学性质和对NO-CO反应的催化性能，并讨论了二者的关系。主要的工作和结论如下：1) 以La_2CuO_4为模型化合物研究了制备方法对它的性质的影响：用四种制备方法：柠檬酸络合爆炸法，聚乙二醇凝胶法，聚丙烯酰胺凝胶法，DTPA络合法合成了La_2CuO_4。比较了四种方法的特点，和制备方法对La_2Cu0_4的结构的影响，并对所得La_2CuO_4在NO-CO反应中的催化活性的影响进行了研究。结果发现聚乙二醇凝胶法和DTPA络合法有利于形成好的晶形，而聚乙二醇凝胶法和聚丙烯酰胺凝胶法对NO-CO反应有较好的活性，这是由于由不同制备方法得到的样品中的缺陷的种类和含量不I司所致。2) La_(1-x)Ba_xCuO_(3-λ)系列中Ba含量对它的性质的影响：用柠檬酸络合法合成了LaBa_2Cu_3O_(7-λ)，LaBaCu_2O_(5-λ)，La_2BaCu_3O_(7-λ) La_4BaCu_5O_(13-λ)及YBa_2Cu_3O_(7-λ)五种钙钛石结构的复合氧化物。XRD分析表明此系列样品均为层状ABO_3结构（分别为二，三，五层）。用XPS和O_2-TPD对样品中的氧种进行了研究，结果显示样品中存在着两种活性氧种：α氧种和β氧种。在O_2-TPD中低温脱附的是α氧种，它可归属于化学吸附氧与样品中的氧空位的浓度有关。β氧种的脱附温度较高，它归属于晶格氧。利用H_2-TPR和化学分析的手段对样品中的金属离子和活性氧的稳定性进行了表征。结果显示大量的氧空位和Cu~(3+)存在于样品中，并且它们的浓度受Ba离子浓度的影响。此系列样品对CO还原NO的活性研究表明：它们的活性远远高于结构类似的Ln_2CuO_4和Ln_2NiO_4等复合氧化物，在低于300 ℃时N0转化率已接近100％．分析结果表明Cu~(3+)和氧空位对活性起很重要的作用。Ba离子的作用是：一方面使含Cu的ABO_3结构稳定；另一方面使样品更容易吸附NO。3) La_4BaCu_5O_(13-λ)中Mn或C0逐步取代Cu对样品性质的影响合成了两系列分别由Mn或Co逐步取代Cu的样品，XRD分析表明它们仍旧是钙钛石结构。通过XPS，O_2-TPD和化学分析方法对样品中的活性氧种进行了表征，结果表明，当Mn逐步取代Cu离子时，晶格氧增加，而吸附氧开始变化较小，当Mn含量大于Cu含量时，吸附氧迅速减少。在Co取代样品的O_(1s)的XPS谱中，氧种变化较Mn取代的小，这表明Co离子对样品中的氧空位含量的影响较Mn离子的小。氧化还原性能的研究表明当Cu离子被Mn或Co离子部分取代后，Cu离子变得更容易被还原，这表明Cu-M(Mn或CO)之间发生了协同作用，使Cu离子更活泼。当Mn或Co部分取代Cu离子之后，样品对CO还原NO反应的催化活性明显提高，当取代含量达到一定程度时（即X ≥ 3），催化活性迅速降低，这表明Cu离子在反应中起着很重要的作用，经过分析我们认为反应机理如下：Cu~(3+)-O~=-Cu~(3+) + CO → Cu~(2+)-□-Cu~(2+)+CO_2 Cu~(2+)-□-Cu~(2+) → Cu~(3+)-□-Cu~(2+) Cu~(3+)-□-Cu~(2+) + NO~-Cu~(3+)-NO-Cu~(2+) 2Cu~(3+)-NO-Cu~(2+) → 2Cu~(3+)-O~=-Cu~(3+) + N_2 式中□是氧空位，Cu~(3+)-□ 是F心。掺杂部分Mn或Co后，催化活性的提高可以归属于Cu-M之间发生的协同作用使Cu离子更活泼，表征结果表明Cu-Co之间的协同作用较Cu-Mn之间的弱（这可能是由于Co，Cu之间化学性质相似），但掺杂Co的样品的活性较掺杂Mn的要高，同时我们在反应中发现，Co含量较高的样品中反应产物中N_2O比掺杂Mn的样品高出许多，因此我们认为Co离子对反应中反应中间产物N_2O的生成比Mn离子要活性。第二部分以水滑石化合物为前体的复合氧化物水滑石类化合物属于一种阴离子粘土，由带正电荷的金属氧化物／氢氧化物和层间阴离子及水分子组成。以水滑石为母体经焙烧制得的氧化物催化剂用于氧化反应的实例尚不多，且大多用于液相催化反应。最近有文献报道含Co，Cu，Ni水滑石经焙烧后对N_2O分解有很好的活性，但还没有关于此类化合物应用于NO还原和分解的文献报道。我们首次将以水滑石为母体经焙烧制得的尖晶石催化剂用于催化消除NO_x的反应中，考察和表征了变更过渡金属离子时Co-M-Al系列和Mg-M-Al系列催化剂在CO还原NO，NO吸附和NO分解反应中的活性。1) 以Mg-M-Al水滑石为前体的催化剂用共沉淀法合成了一系列Mg-M-Al水滑石（M = Cr，Fe，Mn，Co，Ni，Cu；Mg/M/A1 = 3/1/1）。XRD表征表明所有化合物均为典型的水滑石化合物。通过TG-DTA考察了焙烧对样品的结构和组成的影响。450 ℃焙烧后所有样品的XRD图中仅能发现MgO相，表明过渡金属氧化物均匀地分散在MgO-Al_2O_3中，换句话说，所得样品焙烧后是过渡金属氧化物负载在MgO-Al_2O_3载体上。H_2-TPR研究进一步证实过渡金属氧化物在载体上得到了稳定。此系列样品对C0还原N0反应活性的测定表明Mg-Al-Cu样品表现出远远高于其它样品的活性，而Mg-Al和Mg-Ni-Al在550 ℃以下对反应几乎没有活性，其它样品表现出一定的活性。2) 以Co-M-Al水滑石为前体的催化剂体系经共沉淀法合成了Co-M-Al水滑石（M = 过渡金属），经焙烧后发现样品中有尖晶石相出现。比表面研究表明，在500-700 ℃之间比表面变化较小大约在80m~2/g左右，在更高温度焙烧后比表面迅速下降。此系列样品对NO的吸附性能研究表明Co-Al，C0-Ni-Al，Co-Cr-Al，Co-Fe-Al表现出较高的吸附性能，尤其是Co-Ni-Al在100 ℃对NO表现出100％的吸附；其它样品对NO的吸附较低。用过渡金属离子中d轨道电子在吸附前后的晶体场稳定化能的变化可以很好地解释此系列样品对NO的吸附性能。对NO分解的活性测定表明Co-Ni-A1，Co-Cr-A1和Co-Al表现出了较好的活性，其中Co-Ni-Al的活性最高。其它样品在600 ℃以下几乎没有活性。分析结果表明样品对NO分解有活性的催化剂必须具备两个条件：1：对NO有较好的吸附性能；2: NO分解后产生的氧可以容易的脱附。除Co-Al外，所有样品对CO还原NO表现出很高的活性：在150 ℃即有较高的NO转化率，在180 ℃NO转化率即可达到100％。催化剂的氧化还原性能在反应中起着很重要的作用，H_2-TPR研究发现掺杂其它过渡金属后Co离子的还原温度明显降低，表明Co离子得到了活化。3) 以Co-Cu-Al水滑石为前体的样品用共沉淀法合成了一系列Co/Cu/Al含量不同的水滑石化合物，包括Co/Cu/Al分别为7/1/1，3/1/1及1/1/1和仅含Co或Cu的Co/Al = 3/1，Cu/Al = 3/1等一系列样品。XRD结果表明除Cu-Al外其它样品经焙烧后均出现了尖晶石相。Cu-Al样品经焙烧后出现了CuO相表明样品为CuO负载于Al_2O_3上。NO和CO的TPD研究表明三组份样品对NO和CO的吸附明显高于二组份样品，而且含CO量高的样品对NO和CO的吸附能力更好，表明Co起较强的作用。在三组份样品的NO-TPD脱出物中发现有N_2O和N_2，表明NO在样品表面的吸附为活化吸附。对CO还原NO反应活性的研究表明，三组份样品的活性远远高于二组份样品，且含Co量高的样品活性较高，表明在此系列样品中Co离子起决定性作用，而Cu离子起助催化作用。通过对反应中各组份含量的变化分析，我们认为反应机理如下：CO + O-Cat → CO_2 + □-Cat NO + □-Cat → NO-Cat 2(NO-Cat) → N_2O + O-Cat + □-Cat N_2O + □-Cat → N_2O-Cat N_2_O-Cat → N_2 + O-Cat 2(N_2O-Cat) → N_2 + 2(O-Cat) O-Cat是样品中的晶格氧，在Co-Al中加入其它过渡金属离子使样品中的晶格氧得到活化，因此，催化活性得到提高。用以水滑石为前体，共沉淀法和固相反应法等三种制备方法合成了一系列Co-Cu-Al催化剂，发现以水滑石为前体的样品不论是对NO，CO的吸附性能还是对NO-CO反应的催化活性都远远高于其它方法制备的样品，这可能是由于水滑石可以起到一个模版作用，使Cu, Co离子分散的更均匀，以及使催化剂表面的含氧基团丰富。