铵态氮肥对黄土高原典型土壤氮素激发效应的影响

以黄土高原从北向南不同地区典型土壤类型为对象,采用Bremner淹水培养法,研究铵态氮肥对黄土高原典型土壤氮素的激发效应。结果表明,在测定NH4+-N的激发效应时,只有考虑粘土矿物对有机氮矿化产物或者添加NH4+-N的固定,才可获得可靠结果。在培养20 d和60 d时,NH4+-N对不同土类氮素激发效应存在极显著和显著的影响(P≤0.01和<0.05);培养40 d时,尽管不同土类氮素激发效应也存在很大差异,但统计检验不显著。从整体评价,NH4+-N对土垫旱耕人为土和黄土正常新成土表现出正的激发效应,而对干润砂质新成土表现出负的激发效应,对简育干润均腐土在培养20 d和40 d时无激发效应,而在培养60 d时,表现出显著的负激发效应。结果还看出,在培养40 d和60 d时,NH4+-N对农田土壤表现出负激发效应,对林地和裸地土壤表现出正激发效应,而草地土壤在培养40 d时为正激发效应;培养20 d和60 d时无激发效应。添加有机物料在培养20 d和40 d时对激发效应的影响不显著(P=0.0872和0.1641),培养时间延长至60 d时影响显著(P=0.049)。添加紫花苜蓿(Medicago sati-v...

线性低密度聚乙烯的官能化及其结构和性能研究

本文利用辐照产生的过氧化物作为引发剂，以丙烯酸（AA）、甲基丙烯酸环氧丙酯（GMA）和马来酸酐（MAH）为接枝单体，研制了官能化线性低密度聚乙烯（LLDPE）。利用红外光谱（FT－IR）对接枝物进行了表征。线性低密度聚乙烯接枝丙烯酸在 1712 cm~(-1) 处的羰基吸收峰；线性低密度聚乙烯接枝甲基丙烯酸环氧丙酯在 1720 cm~(-1)和840、910cm~(-1) 处的羰基与环氧吸收峰；线性低密度聚乙烯接枝马来酸酐在 1788和 1712cm~(-1)处的酸酐和羰基吸收峰均证明单体已经接枝到线性低密度聚乙烯分子链上。采用化学滴定法测定了官能化线性低密度聚乙烯的接枝率，并提出了其接枝反应的机理。系统研究了单体浓度、预辐照剂量、反应时间、反应温度等对接枝率和熔体流动速率的影响。研究结果表明，在一定工艺条件下，可以得到高接枝率，无凝胶的官能化线性低密度聚乙烯。通过以接枝单体特征基团的吸收峰（AA 1712 cm~(-1)、GMA 1720 cm~(-1)）与内标峰（1738 cm~(-1)）的强度比为纵坐标，以化学滴定法测得的相应单体接枝率为横坐标，得到了用红外光谱法测定接枝率的标准曲线。利用它可以方便、快速、准确地得到某一未知官能化产物的接枝率。用DSC研究了LLDPE及LLDPE-g-AA的热学性能。发现LLDPE-g-AA的ΔH_m下降，结晶温度升高大约4 ℃。这是由于在非极性的线性低密度聚乙烯分了链中引入了极性基团，使聚乙烯分子链的规整性下降，结晶缺陷增多，晶体的完善下降，从而使接枝物的ΔH_m下降，结晶度变小。等温结晶的结果表明，接枝物结晶速率大于纯 LLDPE的结晶速率，并且随接枝率的增加结晶速率加快。说明接枝到 LLDPE 分了链上的AA分子起到了成核剂的作用，从而使接枝物结晶速度加快。利用SEM观察LLDPE-g-AA 的球晶大小，发现 LLDPE-g-AA 的球晶尺寸明显减小，这进一步证实了前面的结论。测定了极性液体在不同接枝率的 LLDPE-g-AA 膜表面的接触角。发现随着接枝率的增加，接触角显著下降。采用 Zisman 作图法和接触角与表面张力的相关关系式得到了不同接枝率LLDPE-g-AA 的临界表面张力。并利用测接触角的方法计算了 LLDPE/LLDPE-g-AA 共混物的表面能。结果表明，共混物表面能随LLDPE-g-AA含量的增加而增加。用毛细管流变仪研究了官能化线性低密度聚乙烯的流变性能。结果表明，在剪切应力大于2.5×10~4 Pa时，其表现粘度比纯 LLDPE的小，流动性明显提高，加工成型性能得到了改善，且其表观粘度随AA含量的增加而减小，这说明接枝到 LLDPE分子链上的 AA 分子起到了内润滑剂的作用。官能化线性低密度聚乙烯的力学性能测试结果表明，其拉伸强度、模量和断裂伸长率没有显著的变化，这对于实际应用有着非常重要的意义。将官能化线性低密度聚乙烯与金属铝进行复合，测定了其剥离强度。结果表明：由于引入了极性基团，其与铝复合的剥离强度大大提高。接枝率、粘合时间、粘合温度和压力等均会对剥离强度产生较大影响。利用SEM 和 XPS对剥离表面进行了研究，发现剥离的铝表面有一个新的Al_(2p)峰，并且其谱图变宽。剥离铝表面O_(1S)结合能与纯铝表面及剥离 LLDPE-g-AA 表面的O_(1S)结合能不同，说明其处于不同的环境中。上述结果证明 LLDPE-g-AA 与铝在界面处可能发生了反应，从而使其剥离强度大大提高。

藏北湖区拉弄蛇绿岩枕状玄武岩地球化学特征及其成因

根据普通病人肠内营养制剂的设计原理，以牡蛎肽为蛋白质来源，麦芽糊精为碳

锗硅合金半导体中无声子参与光跃迁机制研究

研究了Si_1-xGe_x合金半导体中无声子参与光跃迁的产生机制,对由杂质无规分布引起的无声子参与光跃迁给出了一个物理模型.用此模型计算了光跃迁遇极矩,给出了跃迁偶极矩的上限.提出了未掺杂Si_1-xGe_x合金半导体中无声子参与光跃迁的一种跃机制,认为是Ge原子周围波函数畸变的集体行为.

基于双边滤波和双树复小波的图像去噪算法

中国科学院

川西亚高山针叶林主要针叶树种年轮生态学研究

米亚罗地区是四川西部较为典型的亚高山针叶林区域之一。为建立该地区主要针叶树种岷江冷杉、云杉、紫果云杉和红杉的年轮宽度年表资料，了解不同海拔高度岷江冷杉原始林和不同恢复过程的人工针叶林及次生混交林树木径向生长规律，结合样地调查，用生长锥钻取了树木芯样做年轮生态学分析。芯样经过标准化程序固定和打磨抛光后，用WinDENDRO图像分析系统测量年轮宽度序列，用COFECHA程序交叉定年和控制测量数据质量，用ARSTAN程序建立了4个主要针叶树种的地区年表和不同海拔高度岷江冷杉林及人工针叶林和次生混交林针叶树的样地年表。 4个主要针叶树种年轮宽度年表的平均敏感度低于0.2，而其晚材宽度年表都具相对较高的平均敏感度。早材宽度与年轮总宽度标准化年表间的相关系数均在0.9以上；晚材宽度与年轮总宽度标准化年表间的相关系数则种间差异较大，红杉的最高，岷江冷杉的最低。岷江冷杉晚材宽度与年轮总宽度的相关性从1970年以后明显下降，而其他种的相关系数则随时间变化较小。树种之间标准化年表显著正相关，而云杉与紫果云杉和红杉与岷江冷杉之间相关系数明显较高。年表序列的第1主分量表达了4个树种树木共同径向生长变化格局；第2至第4主分量分别表达了云杉属和冷杉属、常绿针叶树种和落叶针叶树种以及云杉和紫果云杉树木径向生长变化差异。 不同海拔高度的8个岷江冷杉样地年轮宽度年表序列敏感度大体上随海拔高度升高而降低。各样地早材宽度与年轮总宽度年表之间的相关系数均在0.9以上，且随海拔高度变化不大；晚材宽度与年轮总宽度之间的相关系数随海拔高度的变化较大，并有随海拔升高而降低的趋势。样地年表序列之间相关系数差异很大，高海拔样地年表间多为显著正相关；低海拔样地年表间的相关系数变化不一；高海拔和低海拔样地年表之间相关性较差，且多不显著。样地年表的第1主分量能解释年表序列总方差的37.5%，反映了不同海拔高度岷江冷杉林木共同的径向生长变化格局；第2和第3主分量分别解释总方差的24.5%和18.2%，表现出明显的高海拔和低海拔样地树木间不同的径向生长变化，除一些样地例外，它们一般与低海拔样地年表有正相关，与高海拔样地年表有负相关。在那些另外的样地，海拔以外的其他因素可能也影响了树木径向生长变化。不同海拔高度样地林木的生长抑制和生长释放频率在不同时期表现出较大的差异，表明了不同的干扰历史和林木补充时间。 人工针叶林和次生混交林各样地林木早材宽度与其年轮总宽度年表之间相关系数均高达0.9以上；晚材宽度与年轮总宽度年表之间也都显著正相关，但人工针叶林样地的明显较高。样地年表序列之间的相关关系表现为，林分起源和经营管理相似的样地年表之间的相关系数明显较高，如人工针叶林与人工针叶林尽管树种不同，但样地年表之间显著正相关，而与次生混交林样地年表间关系不显著；反之亦然。综合比较各项生长参数及不同时期的树木径向生长速率，人工针叶林树木的胸径增长至少在40年以内是优于次生混交林的同种（或不同种）针叶树的。不同样地林木生长释放和生长抑制及人工针叶林树木胸高断面积增长分析表明，除严重的人为干扰外，林分郁闭后林木密度过大是造成高频率生长抑制的主要原因，在林分发育的适当时期通过抚育间伐等措施调控林分密度，是保证林木胸高断面积在一定时期内保持较高的连年增长的关键。日本落叶松作为引进的树种，在海拔3100 m左右种植表现良好，近30年来各项生长指标均高于林龄相近的云杉人工林，因此，适当用其作为川西亚高山针叶林采伐迹地快速恢复是合理的。 Miyaluo area is one of the typical regions covered by subalpine coniferous forests in western Sichuan province of southwestern China. To develop the regional tree-ring width chronology series for the dominant conifers such as Abies faxoniana, Picea asperata, P. purpurea and Larix potaninii, and to understand the radial growth patterns of conifers in Abies faxoniana natural forest stands at different altitudes, and in coniferous plantations and natural regenerated mixed stands in their different restoring processes as well, increment cores were sampled in the field together with conventional plots investigations for dendroecological analyses. After the increment cores being prepared according to standard procedures, the ring widths (total-ring and intra-ring widths) were measured with a WinDENDRO image-analysis system, and the measured tree-ring sequences were crossdated and quality-controlled with the software COFECHA. Using the software ARSTAN, we developed tree-ring width based chronology series of the four dominant conifers, eight site-specific Abies faxoniana chronologies, and seven site-specific chronologies of conifers in coniferous plantations and natural regenerated mixed stands. Mean sensitivities for total ring width chronologies of the four sampled dominant conifers were all below 0.2, while those for the latewood width chronologies of the same species were relatively much higher. Correlation coefficients between standard earlywood and total ring width chronologies of the four conifers were all above 0.9, but those between standard latewood and total ring width chronologies exhibited differences among species, with the coefficient of Larix potaninii the highest and that of Abies faxoniana the lowest. Correlation coefficients between latewood and total ring width of A. faxoniana obviously decreased from 1920-1970 for successive 50-year segments with 10-years lag analyses, though the same for the other three species changed unnoticeably with time. Tree-ring standard chronologies among species showed significant positive correlations, with the correlation coefficients between chronologies of Picea asperata and P. purpurea, and of Larix potaninii and Abies faxoniana relatively much higher. The first principal component of tree-ring chronologies represented the common radial growth patterns of the four conifers in Miyaluo area. The second, third and fourth PCs expressed the differences in radial growth responses for the genus Picea and Abies, for the evergreen and deciduous confers, and for the two species of the genus Picea, respectively. In general, mean sensitivities of the eight Abies faxoniana site-specific tree-ring width chronologies decreased with increasing altitude. The correlation coefficients between earlywood and total ring width chronologies for all sites reached 0.9, which did not change much with altitude; but those between latewood and total ring width chronologies diversified, with a decreasing tendency from lower altitudinal sites to higher altitudinal sites. Correlation coefficients among site chronologies varied considerably, with significant positive correlations among higher site chronologies, mixed results among lower site chronologies, and poor and insignificant correlations between chronologies of higher site and lower site. The first PC, which represents 37.5% of the total variance, reflected a common radial growth response at sites of different altitudes, and it showed a tendency of explaining more variance with increasing altitude. The second and the third PCs contributed to 24.5% and 18.2% of the total variance, respectively, exhibiting distinctive differences in radial growth responses between low- and high-altitudinal sites. With some exceptions, the radial growth represented by the second and third PCs had a positive correlation with that at the low-altitudinal sites and a negative correlation with that at the high-altitudinal sites. For those exceptional sites, factors other than altitude might also play a role in affecting tree-ring growth variations. Trees in stands of different altitudes showed great differences in frequencies of growth suppressions and releases through times, suggesting different disturbance histories and periods when trees recruiting to the canopy. Correlation coefficients between earlywood and total ring width chronologies for all sites of coniferous plantations and natural regenerated mixed stands were also above 0.9; and the same between latewood width and total ring width chronologies all positively correlated, too, with the coefficients of the coniferous plantations obviously much higher. Correlations among site chronologies showed that the coefficients among sites with similar stand origin and management regimes were much higher than those among sites with different stand origin and management regimes. For example, significant positive correlations were found for chronologies among different coniferous plantations, irrespective of species differences; while insignificant correlations between chronologies of the same conifer from a coniferous plantation and a natural regenerated mixed stand, and vise versa. Integrative comparisons of different tree growth parameters and radial growth rates at different stages indicated that the diameter at breast height (DBH) increments for trees in coniferous plantations were faster than those for trees of the same (or different) species in the natural regenerated mixed stands, at least within their first 40 years of stand development. Analyses of growth releases and suppressions, and basal area increments of trees in different stands demonstrated that over-dense individuals after canopy closure was the main factor resulting in high frequencies of radial growth suppressions, with some exceptions of severe man-made disturbances. Therefore, to ensure a continuous basal area current annual increment in certain periods, tree density controlling through thinning in due time during the stand development process are necessary. It should be mentioned that, as an introduced conifer to Miyaluo area, Larix kaempferi grew quite well at altitude of ca. 3100 m after planting in 1970s. In their near 30 years of stand development, Larix kaempferi trees exhibited faster growth in various parameters than Picea asperata trees of the similar stand age did. Thus we think it reasonable to use Larix kaempferi as a fast restoring species at appropriate sites of cutting blanks of subalpine coniferous forests in western Sichuan.

白腐菌选择性降解木质素的研究

对15株白腐真菌进行了以玉米秸秆为基质的初步筛选，从中获得一株选择性系数较高的菌株Y10，并对其降解玉米秸秆的情况进行了研究。结果表明，在30天的培养过程中菌株Y10对玉米秸秆降解的选择性系数都大于1，第15天选择性系数最高为3.88。对未经降解和降解过的玉米秸秆分别作了紫外光谱和红外光谱分析，结果表明，经该菌降解后玉米秸秆的化学成分发生了很大变化，且木质素的降解程度要大于纤维素的降解程度。对菌株Y10进行了ITS-5.8S rDNA序列鉴定，初步判定其为Cerrena sp.。 为了考查不同的外源添加物对菌株Y10降解玉米秸秆的影响，在以玉米秸秆为基质的固态发酵培养基中分别添加了7种金属离子、8种碳源、6种氮源。结果显示，这7种金属离子均能促进木质素的降解，并且一定浓度的某些离子明显抑制纤维素的降解；其中添加0.036%的MnSO4·H2O和0.36%的MgSO4·7H2O对纤维素降解的抑制作用比较强，降解率分别为0.96%和1.31%，木质素的选择性系数分别达到了34.40和20.17。8种碳源中除麦芽糖外都能促进木质素的降解，除微晶纤维素外都明显促进纤维素的降解。6种氮源中酒石酸铵、硫酸铵、草酸铵和氯化铵的添加都会使该菌生长变慢，而且氮源浓度越高菌丝生长越慢。外加碳源和金属离子对半纤维素降解和选择性系数的影响不大。 同时对菌株Y10在液态培养下产木质素降解酶的条件和培养基做了优化。结果表明，在初始产酶培养基中，菌株Y10的漆酶酶活在第10d达到最高，锰过氧化物酶酶活在第11d达到最高，基本上检测不到木质素过氧化物酶。菌株Y10产漆酶的最适温度为32℃，最适PH为6.0；产锰过氧化物酶的最适温度为32℃，最适PH为6.5。菌株Y10产漆酶的最佳碳源为甘露糖，最佳氮源为酒石酸铵，最适诱导剂VA浓度为3 mmol/L，最适表面活性剂TW-80浓度为1%。 利用响应面法对其产漆酶的培养基进行优化，优化后的培养基配方为葡萄糖10.00 g/L，酒石酸铵0.50 g/L，大量元素296.50 ml/L，微量元素100.00 ml/L，NTA 1.40 g/L，VA 5.00 mmol/L，吐温-80加入量为0.10%。进行了菌株Y10产漆酶的验证实验，实测酶活为5282.56 U/L，与预测酶活5162.73 U/L接近。在优化后培养基中，菌株Y10在第14 d达到生长的最高峰，第20 d时，漆酶酶活最高，为11325.00 U/L；第16 d时，锰过氧化物酶酶活最高，为30.77 U/L。 对菌株Y10的漆酶酶学性质做了初步的研究，结果显示，酶反应的最适温度为40℃-65℃，最适PH为3.0。在40℃，PH=3.0时，漆酶催化ABTS反应的米氏方程为 。 Fifteen white-rot fungi based on corn stalk were screened. One white-rot fungus Y10 with high selectivity value was obtained. The degradation of corn stalk was initially studied. The results indicated that the selectivity value was above 1 during the 30 day-cultivation and the highest was 3.88 after 15 days. The composition of untreated and treated stalk was analyzed through ultraviolet spectroscopy and infrared spectroscopy. It was found that the composition of treated stalk was greatly altered and the degree of the degradation of lignin is greater than the cellulose. Y10 was identified as Cerrena sp. by ITS -5.8S rDNA sequence analysis. The influence of metal ions, carbon sources and nitrogen sources on corn stalk degradation by white-rot fungus was studied. While all seven metal ions could promote lignin degradation, the cellulose degradation was best inhibited at certain ion concentrations. Notably, when 0.036% MnSO4·H2O and 0.36% MgSO4·7H2O were added into the medium, the cellulose degradation was restrained to the extents that the coefficients of lignin selectivity rose to 34.40 and 20.17 respectively. It was also found that all carbon sources except maltose can promote lignin degradation. The addition of carbon sources other than microcrystalline cellulose significantly promoted cellulose degradation. The addition of the nitrogen sources, ammonium tartrate, ammonium sulfate, oxalate, ammonium chloride, resulted in remarkable inhibition to mycelium growth; the larger the concentrations of nitrogen sources are, the slower the mycelium grew. The addition of carbon sources and metal ions had less impact on the degradation of hemicellulose and selectivity value. Meanwhile, we optimized the conditions and culture medium of the lignin-degrading enzyme production of strain Y10. The results showed that in the initial culture medium, the Lac activity was highest at the 10th day, the MnP activity was highest at the 11th day and the LiP could not be detected. The optimum condition of Lac was at temperature 32 and PH =6.0 and the optimum condition of MnP was at temperature 32 and PH =6.5. The optimum carbon source for Lac was seminose, the optimum nitrogen source was ammonium tartrate, the optimum content of VA was 3 mmol/L, the optimum content of TW-80 was 1%. PB and RSM were used to optimize the culture medium of laccase by white-rot fungus Y10. The optimum culture medium was consist of glucose 10.00 g/L, ammonium tartrate 0.50 g/L, macro elements 296.50 ml/L, trace elements 100.00 ml/L, NTA 1.40 g/L, VA 5.00 mmol/L, TW-80 0.10%. Under the optimal conditions, the activity of laccase was 5282.56 U/L and the experimental value agreed with the predicted value 5162.73 U/L. The biomass was highest at the 14th day, the Lac activity was highest at the 20th day, the MnP activity was highest at the 16th day. The results of the studies on the characteristics of Lac showed that the optimum temperature for Lac activity is 40℃-65℃ ; the optimum PH for Lac activity is 3.0 and under 40℃，PH=3.0, the Michaelis-menten equation of Lac catalized ABTS oxidation was .

耐酸产甲烷菌的分离及其复合菌剂的研究

本文从成都龙泉垃圾填埋场和宜宾造纸厂分离到耐酸性能优良的高温产甲烷菌RY3和中温产甲烷菌SH4，并将其与实验室现有的利用不同底物的产甲烷菌配伍组合成了复合菌剂。采用活性污泥作为固体附着物，研制出了固体产甲烷菌复合菌剂。 菌株RY3的pH耐受范围为5.5～10.5，最适生长pH 6.0～8.0。菌株RY3为革兰氏阳性，长杆状，多数单生，不运动；菌落浅黄色，形状近圆形；利用H2+CO2或甲酸盐作为唯一碳源生长，不利用乙酸盐，对氯霉素非常敏感。该菌最适生长温度为55℃～65℃，最适NaCl浓度为0～2%。根据形态和生理生化特性及16S rDNA序列分析将其初步定为热自养甲烷热杆菌（Methanothermobacter thermautotrophicus）。添加RY3菌液与仅添加厌氧污泥作为接种物相比一周内可使达到最大产甲烷速率所需时间缩短三分之二，甲烷总产量提高约1.8倍。菌株SH4的生长pH范围5.5～9.5，其对酸碱具有良好的适应性，培养3天后，在初始pH值为6.0～8.0的培养基中甲烷产量相差不大，且基本达到最大产量。SH4革兰氏染色阳性，短杆状，多数单生，不运动；菌落近圆形，微黄；利用H2+CO2或甲酸盐作为唯一碳源生长，不利用乙酸盐，对氯霉素非常敏感。SH4最适生长pH 为7.0，最适生长温度为35℃，最适NaCl浓度为0～1.5%。实验表明，添加SH4菌液与仅添加厌氧污泥作为接种物相比可使产甲烷启动时间缩短三分之一，甲烷总产量亦有大幅提高。从形态和生理生化特征以及16S rDNA序列分析表明SH4为嗜树木甲烷短杆菌（Methanobrevibacter arboriphilus）。 以活性污泥为附着物，与培养基和菌种经搅拌后厌氧发酵可得产甲烷菌固体复合菌剂。固体复合菌剂的pH耐受范围为5.5～9.5，温度耐受范围为15℃～65℃，表明其对环境的适应性较强。以猪粪为底物进行厌氧发酵，接种复合菌剂进行试验，以接种实验室长期富集的产甲烷厌氧污泥作为对照，在20℃时，发酵甲烷浓度与对照基本一致，但每日产气量优于对照，第15天时接种复合菌剂的发酵瓶每日产气量是对照的1.59倍；50℃时达到最大甲烷含量所需时间比对照缩短三分之二，三周内总产气量约为对照的2.7倍，甲烷总产量约为2.8倍。以不加接种物为对照，接种复合菌剂20℃时发酵甲烷含量达到50%约需2周，对照2周内甲烷含量最高仅为4.3%；50℃时接种复合菌剂发酵仅需约1周甲烷含量便可达50%，对照则至少需要2周。 In this paper, high-temperature Methanogen RY3 and middle-temperature SH4 were isolated from Chengdu Longquan refuse landfill and Yibin paper mill. They could be used to make compound inoculum that producing methane with the existing Methanogens utilized different substrate. With using anaerobic activated sludge be solid fixture, the process had been designed to produce solid compound inoculum. Strain RY3 possessed excellent capacity of acid and alkali-tolerant. The pH-tolerant scale of RY3 was 5.5～10.5 and its optimum pH value for growth was 6.0～8.0. RY3 was G+, long-rod shape, monothetic and nonmotile, the colony was pale yellow with suborbicular-shape. Formate or H2+CO2 but not acetate was utilized by RY3 as sole C-source, and it was very sensitive to chloramphenicol. Besides, strain RY3 grew fastest at 55℃～65 and 0℃～2% NaCl. Characteristics of modality and physiology with sequence analysis of the 16s rDNA gene of strain RY3 preliminarily showed that it was Methanothermobacter thermautotrophicus. The experiments indicated that the time which began to produce methane with the highest velocity could be shortened two third by adding RY3 in one week, and the total methane production also was 1.8 times than before. Strain SH4 possessed wide scale of growing pH（5.5～9.5）and excellent ability of acclimatizing itself to acid-alkali. The methane production had no apparent difference among those cultivated in different initial pH（6.0～8.0）after three days and equaled to the maximum production basically. Cells of SH4 were G+, short-rod sharp, monothetic and nonmotile. The colony was pale yellow with suborbicular-shape. Formate or H2+CO2 but not acetate was utilized by SH4 as sole C-source, and it was very sensitive to chloramphenicol. Besides, it grew fastest at pH 7.0，55 ℃～65 and 0℃～2% NaCl concentration. The experiment indicated the time that began to produce methane could be shortening one third by adding SH4. And the total methane production also rose apparently. Characteristic of modality and physiology with sequence analysis of the 16S rDNA gene of strain SH4 demonstrated it was Methanobrevibacter arboriphilus. The activated sludge was utilized as fixture, mixed with culture medium and inocolum, that the solid compound inoculum could be produced by anaerobic fermentation. The compound inoculum could grow between pH 5.5～9.5, 15℃～65. It demonstrated the compound inoculum ha℃ve great ability of adapting to circumstance. In the experiment that making pig manure be substrate and taking the anaerobic sludge producing methane that cultured in long term in laboratory to be comparison, the concentration of methane in fermentation added compound inoculum almost equal to the comparison at 20℃, but the volume of gas production could be a little higher. The gas production everyday inoculated compound inoculum was 1.59 times to comparison. The time that the concentration of methane to maximum could be shortening by two third by adding compound inoculum, and the total gas production was 2.7 times to comprison while the total methane production was 2.8 times. If take the no inoculum be the comprasion, anaerobic fermentation added compound inoculum made the concentration of methane to 50% in 2 weeks but the comparison only to 4.3% at 20℃. The time that the concentration of methane to 50% by adding compound inoculum only need 1 week, but the comparison need 2 weeks at 50℃.