Experimental Investigation of Performance of a Miniature Direct Methanol Fuel Cell in Short-Term Microgravity

Experimental study of a liquid fed direct methanol fuel cell has been conducted in different gravity environments. A small single cell with 5 cm x 5 cm active area has single serpentine channel on the graphite cathode polar plate and 11 parallel straight channels on the graphite anode flow bed. Cell voltage and current have been measured and two-phase flow in anode channels has been in situ visually observed. The experimental results indicate that the effect of gravity on power performance of the direct methanol fuel cell is large when the concentration polarization governs fuel cells operation. Gravitational effect becomes larger at higher current density. Increasing methanol feeding molarity is conducive to weaken the influence of gravity on performance of liquid fed direct methanol fuel cells. Increasing feeding flow rate of methanol solution from 6 to 15 ml/min could reduce the size of carbon dioxide bubbles, while the influence of gravity still exist. Transport phenomena inside direct methanol fuel cells in microgravity is also analyzed and discussed.

CO selective oxidation in a microchannel reactor for PEM fuel cell

It is indispensable to remove CO at the level of less than 50ppm in H-2-rich feed gas for the proton exchange membrane (PEM) fuel cells. In this paper, catalyst with high activity and selectivity, and a microchannel reactor for CO preferential oxidation (PROX) have been developed. The results indicated that potassium on supported Rh metal catalysts had a promoting effect in the CO selective catalytic oxidation under H-2-rich stream, and microchannel reactor has an excellent ability to use in on-board hydrogen generation system. CO conversion keeps at high levels even at a very high GHSV as 500 000 h(-1), so, miniaturization of hydrogen generation system can be achieved by using the microchannel reactor. (C) 2004 Elsevier B.V. All rights reserved.

Composite electrode for unitized regenerative proton exchange membrane fuel cell with improved cycle life

To improve the cycle life of unitized regenerative fuel cells (URFCs), an electrode with a composite structure has been developed. The cycle life and polarization curves for both fuel cell and electrolysis modes of URFC operation were investigated. The cycle life of URFCs was improved considerably and the performance was fairly constant during 25 cycles, which illustrates that the composite electrode is effective in sustaining the cyclic performance of URFCs. It shows the URFCs with such an electrode structure are promising for practical applications. (C) 2004 The Electrochemical Society.

Multi-walled carbon nanotubes supported Pt-Fe cathodic catalyst for direct methanol fuel cell

Multi-walled carbon nanotubes supported Pt-Fe cathodic catalyst shows higher specific activity towards oxygen reduction reaction as compared to Pt/MWNTs when employed as cathodic catalyst in direct methanol fuel cell.

Highly conductive, methanol resistant fuel cell membranes fabricated by layer-by-layer self-assembly of inorganic heteropolyacid

Layer-by-layer (LBL) self-assembly is a simple and elegant method of constructing organic-inorganic composite thin films from environmentally benign aqueous solutions. In this paper, we utilize this method to develop proton-exchange membranes for fuel cells. The multilayer film is constructed onto the surface of sulfonated poly(arylene ether ketone) (SPAEK-COOH) membrane by LBL self-assembly of polycation chitosan (CTS) and negatively charged inorganic particle phosphotungstic acid (VIA). The highly conductive inorganic nanoparticles ensure SPAEK-COOH-(CTS/PTA)(n) membranes to maintain high proton conductivity values up to 0.086 S cm(-1) at 25 degrees C and 0.24S cm(-1) at 80 degrees C, which are superior than previous LBL assembled electrolyte systems.

Chitosan/heteropolyacid composite membranes for direct methanol fuel cell

As inorganic proton conductors. phosphomolybdic acid (PMA), phosphotungstic acid (PWA) and silicotungstic acid (SiWA) are extremely attractive for proton-conducting composite membranes. An interesting phenomenon has been found in our previous experiments that the mixing of chitosan (CS) solution and different heteropolyacids (HPAs) leads to strong electrostatic interaction to form insoluble complexes. These complexes in the form of membrane (CS/PMA, CS/PWA and CS/SiWA composite membranes) have been prepared and evaluated as novel proton-conducting membranes for direct methanol fuel cells. Therefore, HPAs can be immobilized within the membranes through electrostatic interaction, which overcomes the leakage problem from membranes.

Influence of electrode structure on the performance of a direct methanol fuel cell

Direct methanol fuel cells (DMFCs) consisting of multi-layer electrodes provide higher performance than those with the traditional electrode. The new electrode structure includes a hydrophilic thin film and a traditional catalyst layer. A decal transfer method was used to apply the thin film to the Nafion(R) membrane. Results show that the performance of a cell with the hydrophilic thin film is obviously enhanced. A cell with the optimal thin film electrode structure operating at I M CH3OH, 2 atm oxygen and 90degreesC yields a current density of 100 mA/cm(2) at 0.53 V cell voltage. The peak power density is 120 mW/cm(2). The performance stability of a cell in a short-term life operation was also increased when the hydrophilic thin film was employed. (C) 2002 Elsevier Science B.V. All rights reserved.

Electrochemical performance of mixed ionic-electronic conducting oxides as anodes for solid oxide fuel cell

Mixed ionic-electronic conducting (MIEC) oxides, SrFeCo0.5Ox, SrCo0.8Fe0.2O3-delta and La0.6Sr0.4Fe0.8Co0.2O3-delta have been synthesized and prepared on yttria-stabilized zirconia as anodes for solid oxide fuel cells. Power output measurements show that the anodes composed of such kinds of oxides exhibit modest electrochemical activities to both H-2 and CH4 fuels, giving maximum power densities of around 0.1 W/cm(2) at 950 degrees C. Polarization and AC impedance measurements found that large activation overpotentials and ohmic resistance drops were the main causes for the relative inferior performance to the Ni-YSZ anode. While interlayered with an Ni-YSZ anode, a significant improvement in the electrochemical performance was observed. in particular, for the SrFeCo0.5Ox oxide interlayered Ni-YSZ anode, the maximum power output reaches 0.25 W/cm2 on CH,, exceeding those of both SrFeCo0.5Ox and the Ni-YSZ, as anodes alone. A synergetic effect of SrFeCo0.5Ox and the Ni-YSZ has been observed. Future work is needed to examine the long-term stability of MIEC oxide electrodes under a very reducing environment. (C) 1999 Elsevier Science B.V. All rights reserved.

A comprehensive comparison of fuel options for fuel cell vehicles in China

Fuel cell vehicles (FCVs) offer the potential of ultra-low emissions combined with high efficiency. Proton exchange membrane (PEM) fuel cells being developed for vehicles require hydrogen as a fuel. Due to the various pathways of hydrogen generation, both onboard and off-board, the question about which fuel option is the most competitive for fuel cell vehicles is of great current interest. In this paper, a life-cycle assessment (LCA) model was made to conduct a comprehensive study of the energy, environmental, and economic (3E) impacts of FCVs from well to wheel (WTW). In view of the special energy structure of China and the timeframe, 10 vehicle/fuel systems are chosen as the study projects. The results show that methanol is the most suitable fuel to serve as the ideal hydrogen source for fuel cell vehicles in the timeframe and geographic regions of this study. On the other hand, gasoline and pure hydrogen can also play a role in short-term and regional applications, especially for local demonstrations of FCV fleets. (c) 2004 Elsevier B.V All rights reserved.

短时微重力条件下燃料电池性能实验研究

开展了不同重力情况下燃料电池性能的实验研究.利用微重力落塔,对常重力和微重力条件下燃料电池发电时其内部的两相流动开展了可视化现场观测.对重力因素对燃料电池内部传质过程的影响进行了分析和讨论.实验结果表明:当电流密度较大时,在微重力环境中燃料电池性能较常重力环境中的有较明显下降.由于微重力条件下浮升力的消失导致气体不能及时从流道中排出,进而对直接甲醇燃料电池内的传质过程产生负面影响.

质子交换膜燃料电池短时微重力性能实验研究

利用落塔开展了不同重力情况下质子交换膜燃料电池性能的实验研究.对常重力和微重力条件下质子交换膜燃料电池发电时其阴极蛇形流场内部的两相流动开展了可视化现场观测.对重力因素对质子交换膜燃料电池内部传质过程的影响进行了分析和讨论.实验结果表明:在常重力环境中,液态水堆积在竖置流道的底部,无法有效排出.聚集在流道内的液态水与反应气体在流道内形成气/液两相流动.在微重力环境中,液态水在气体推动力的作用下从流道的底部上升并沿流道向出口流动.聚集在流道内的液态水排除后,减小了反应气体(氧气)从流道向催化层的传递阻力,从而使质子交换膜燃料电池的性能得到提高.

Enhanced Proton Conduction in Polymer Electrolyte Membranes as Synthesized by Polymerization of Protic Ionic Liquid-Based Microemulsions

Proton-conducting membranes were prepared by polymerization of microemulsions consisting of surfactant-stabilized protic ionic liquid (PIL) nanodomains dispersed in a polymerizable oil, a mixture of styrene and acrylonitrile. The obtained PIL-based polymer composite membranes are transparent and flexible even though the resulting vinyl polymers are immiscible with PIL cores. This type of composite membranes have quite a good thermal stability, chemical stability, tunability, and good mechanical properties. Under nonhumidifying conditions, PIL-based membranes show a conductivity up to the order of 1 x 10(-1) S/cm at 160 degrees C, due to the well-connected PIL nanochannels preserved in the membrane. This type of polymer conducting membranes have potential application in high-temperature polymer electrolyte membrane fuel cells.

直接甲醇燃料电池耐甲醇氧还原电催化剂的研究

燃料电池以其高效、环境友好的发电方式，被誉为21世纪的能源技术。其中，直接甲醇燃料电池（DMFC）更以燃料甲醇来源丰富，价格低廉，储存、携带方便而成为近年的研究热点。目前DNDFC存在的一个主要问题是"甲醇透过"，即甲醇从阳极穿过固体电解质膜进入到阴极，而阴极催化剂一般是Pt/C，因此在阴极会同时发生甲醇氧化和氧还原，严重降低了电池的库仑效率和电压效率。此夕卜甲醇及其氧化中间产物还会使P口C中毒。虽然试验了一些低甲醇透过率的电解质膜，但仍无法完全消除甲醇透过。因此研制对氧还原催化活性高而对甲醇氧化没有活性，即耐甲醇的氧还原电催化剂是一个十分重要的课题。本论文主要从催化剂的组成、热处理、制备方法和载体等方面进行了相关研究，此外，还开展了生物燃料电池阴极电催化剂的研究。具体结果如下：1．热处理对电催化剂性能的影响（1）首次研究了炭载铂（Pt/C）对氧还原和甲醇氧化的催化活性与热处理温度的关系。发现P"C的催化活性随热处理温度的升高而降低，其原因是热处理使R／C中Pt的结晶度提高、粒径变大、表面浓度降低。但是，热处理使PUC催化甲醇氧化活性的降低程度远大于催化氧还原活性的降低程度。该研究提供了一种有效改善P口C催化剂耐甲醇性能的简便方法。（2）研究了炭载四狡基酞著钻（CoPcTc／C）和炭载四苯基铁叶琳（FeTPP／C）对氧还原和甲醇氧化的催化活性与热处理温度的关系。发现800℃热处理的CoPcTc／C对氧还原的催化活性最高；XPS和XRD分析表明，其活性位主要为含CoN4结构的物质。FeTPP／C催化剂与CoPcTc／C类似，700℃热处理的对氧还原催化活性最高。二者对甲醇氧化都没有活性。（3）首次研究了炭载四苯基铁叶琳一铂（FeTPP-Pt/C）复合催化剂对氧还原和甲醇氧化的催化活性与热处理温度的关系。发现热处理使FeTPP-Pt/C对氧还原的催化活性提高，并且优于相应P灯C，这是因为复合催化剂对氧还原的催化活性来源于FeTPP和Pt两部分。另外，FeTPP-Pt／C对甲醇氧化的催化活性随热处理温度的升高而降低，降低幅度大于相应Pt/C，这是因为在复合催化剂中，FeTPP在Pt/C表面的分散会降低甲醇与R的接触。700℃热处理的FeTPP-Pt/C对氧还原的催化活性最高，并且耐甲醇能力很强，非常适合作为DMFC阴极电催化剂。（4）首次研究了FeTPP-TiO2/C复合催化剂对氧还原的催化活性与热处理温度的关系。发现70。℃热处理的FeTPP-TiO2／C对氧还原的催化活性最高，并且稳定性好；复合催化剂提高了氧还原的电子转移数。这是因为TIOZ能够将FeTPP催化氧还原过程中产生的H2O2及时分解为O2和H2O，再重新被FeTPP还原。TIOZ的加入有望改善过渡金属大环化合物催化剂的长程稳定性。此夕卜该复合催化剂对甲醇氧化没有活性。2．制备方法对电催化剂性能的影响（1）首次同时研究了Pt/C对氧还原和甲醇氧化的催化性能，讨论了影响Pt/C催化活性的主要因素。XRD、XPS和TEM分析表明，无定型Pt含量高的Pt/C对氧还原的催化活性较高，表面氧化物含量高的Pt/C对甲醇氧化的催化活性较高。为制备耐甲醇能力强、催化氧还原活性高的Pt/C催化剂提供了理论参考。（2）比较了平衡吸附法和强制沉积法制备的FeTPP-Pt/C催化剂的性能，发现前者对氧还原和甲醇氧化的催化活性都高于后者，这是因为由强制吸附法制备的复合催化剂，FeTPP将一部分Pt覆盖，使其无法发挥活性。3．活性炭载体对Pt/C电催化剂性能的影响利用多种分析手段，系统比较了VulcanXC-72炭和上海松木炭的物理、化学性质对Pt/C电催化剂性能的影响。发现孔径适当、电导率高、灰分和表面含氧基团较少的活性炭作载体时，制得的P口C催化剂的性能较好。为PEMFC中电催化剂载体的选择提供了一些理论依据。4．生物燃料电池阴极电催化剂的研究首次制备了炭载微过氧化物酶-11（MP-11／C）电催化剂，通过循环伏安法、线性扫描法和旋转圆盘电极技术研究发现，MP-11／C对O2还原具有较高的催化活性，并且稳定性好，为生物燃料电池的研制提供了一种较好的酶固定方法。

The effect of methanol and ethanol cross-over on the performance of PtRu/C-based anode DAFCs

In the present work, the cross-over rates of methanol and ethanol, respectively, through Nafion(R)-115 membranes at different temperatures and different concentrations have been measured and compared. The changes of Nafion(R)-115 membrane porosity in the presence of methanol or ethanol aqueous solutions were also determined by weighing vacuum-dried and alcohol solution-equilibrated membranes. The techniques of anode polarization and adsorption stripping voltarnmetry were applied to compare the electrochemical activity and adsorption ability, respectively. To investigate the consequences of methanol and ethanol permeation from the anode to the cathode on the performance of direct alcohol fuel cells (DAFCs), single DAFC tests, with methanol or ethanol as the fuel, have been carried out and the corresponding anode and cathode polarizations versus dynamic hydrogen electrode (DHE) were also performed. The effect of alcohol concentration on the performance of PtRu/C anode-based DAFCs was investigated.

An improved palladium-based DMFCs cathode catalyst

A novel carbon-supported palladium-rich Pd3Pt1/C catalyst prepared by a modified polyol process showed a better cell performance than Pt/C in direct methanol fuel cells, which may be attributed to palladium's inactivity to methanol electro-oxidation while exhibiting good performance to oxygen reduction reaction.