两根大芯双包层光纤激光器获得60W相干输出

报道了一个相位锁定的光纤激光器阵列获得60W的输出，同相模式输出时的斜率效率为37％。对于两种不同的纤芯距离都观测到稳定的高对比度干涉条纹。整个系统在高功率操作时，所用的空间滤波器没有观察到明显的热问题，这充分说明了采用这种方法能够进一步提高相干输出功率。

双包层光纤侧面耦合器

研究了一种侧面抽运双包层光纤的方法，从被剥除了外包层、端面为350μm×400μm的D型双包层光纤内包层上切下长度为3mm的一段柱体，并胶合在相同的双包层光纤内包层的侧面上，构成了柱体-光纤侧面耦合器。半导体激光器的抽运光从该柱体的一端入射并通过它耦合进入双包层光纤的内包层，实验测得耦合器最大耦合效率为85％。该方法适用于输出功率为数瓦的光纤激光器和放大器的侧面抽运。

微棱镜与双包层光纤侧面耦合效率的实验研究

对微棱镜与双包层光纤侧面耦合技术进行了研究。用光学胶把尺寸为1mm×1mm×1mm直角棱镜的直角面胶合在尺寸为330μm×170μm的内包层侧平面上，激光束以一定的角度从微棱镜的另一直角面入射并通过它耦合进入双包层光纤的内包层，实验测得耦合效率为86％。该方法可用于双包层光纤的侧面抽运。

高功率脉冲双包层光纤激光器的新进展

对高功率脉冲双包层光纤激光器的国内外研究进展进行评述，通过建立了小信号瞬态增益模型，对脉冲激光信号经过双包层光纤放大后的波形进行了数值模拟。分析了基于MOPA方式脉冲双包层光纤激光器的几个问题，报道了中科院上海光机所采用振荡-放大（MOPA）方法获得133．8W平均功率脉冲放大输出的实验结果。

两根掺镱大芯双包层光纤激光器获得113W同相输出功率

利用一个自成像共焦腔和一个空间滤波器实现了两掺Yb大芯光纤激光器的位相锁定。观测到稳定的具有高对比度的干涉条纹。相干条纹的对比度为59%，而非相干时对比度为6%。中心条纹的宽度与理论计算结果吻合得很好。对同相模式而言，位相锁定激光器阵列输出达到113W，对应的斜率效率为38.5%。

采用国产双包层光纤的声光调Q激光器

实验报道采用我国自行设计的大模场掺镱双包层光纤，利用简单声光调Q装置，成功实现调Q运转；在1－50kHz调制频率下获得了百纳秒的调Q脉冲，其输出光束质量因子大约为2。当重复频率为1kHz时，获得了脉冲宽度为132ns，能量0.93mJ。同时实验中观察到的调Q脉冲常出现一点锁模现象，针对这一现象进行了讨论。

双程掺镱光纤放大器的增益特征及优化

比较了掺钕光纤和掺镱光纤对1064nm光放大的特点．基于速率方程和传输方程，数值分析了在915nm泵浦下双程掺镱光纤放大器的增益特征，并且和传统的单程放大进行了比较．分析了信号光和泵浦光，以及粒子数沿着光纤方向的分布特点．最后对双程掺镱光纤放大器进行了优化．

光纤激光器及其相干组束

简述了光纤激光器的发展历史，重点介绍了双包层光纤激光器的进展并给出了高功率双包层光纤激光器的最新研究结果。评述了目前国内外高亮度激光的关键技术：光纤激光器的相干组束。介绍了几种典型的相干组束技术并分析了其工作原理。最后给出了相干组束研究的最新结果。

千瓦级双包层光纤激光器冷却方案设计理论和实验研究

尽管双包层光纤激光器的散热性能好于传统的固体激光器的散热性能,光纤激光器中的热沉积仍然是限制提高其输出功率的重要因素.以双端抽运的400W双包层光纤激光器为实例,定量分析了光纤内的热沉积分布.根据所建立的散热模型,为了确保千瓦级双包层光纤激光器安全稳定的运行,抽运端附近的对流换热系数应大于2.8×10-2W·cm-2K-1.据此设计出高功率双包层光纤激光器抽运端冷却装置并成功应用在激光系统中,获得了千瓦级的激光输出.

Tm-doped fibre laser pumped Cr2+: ZnSe poly-crystal laser

Demonstrations of cw lasing in Cr2+:ZnSe poly-crystal are reported. The laser consists of a 1.7-mm-thick Cr2+:ZnSe poly-crystal disc pumped by a Tm-silica double-clad fibre laser at 2050nm. Using a concave high-reflection mirror with a radius of curvature of 500mm as the rear mirror, the laser delivers up to 1030mW of radiation around 2.367 mu m.

Fiber laser hydrophone based on double diaphragms: Theory and experiment

A fiber laser hydrophone with enhanced sensitivity is demonstrated. Two diaphragms with a hard core fixed at each center are used as the sensing element. Theoretical analysis shows that the Young's modulus of the diaphragm and the radius of the hard core have significant effect on the acoustic sensitivity. Experiments are carried out to test this effect and the performance of the hydrophone. The experimental result agrees well with the theoretical result, and a sensitivity of 7 nm/MPa has been achieved.

Passive Q-switched mode locking of double-clading Yb : fiber laser with ion-implanted GaAs

We report the technique of the ion-implanted semi-insulating GaAs wafer used for passive Q-switched mode locking in double-cladding Yb:fiber laser. The wafer was implanted with 400-keV energy, 10(16)/cm(2) dose As+ ions, and was annealed at 600degreesC for 20 min. At the pump power of 5W, we achieved output power of 200mW. The repetition rate of envelope of Q-switched mode locking is 50-kHz with a FWHM envelope of 4mus. The repetition rate of mode locked pulse train was found to be 15-MHz. This is the first report of such a kind of laser to the best of our knowledge.

PERFORMANCE OF DOUBLE SIDEBAND MODULATED PROBE WAVE IN BOTDA DISTRIBUTED FIBER SENSOR

We report on the performance of double sideband (DSB) modulated probe wave in Brillouin optical time domain analysis (BOTDA) distributed fiber sensor. Compared to single sideband (SSB)modulation, along the sensing fiber the pump depletion of DSB modulation is remarkably suppressed in time domain and also has a relatively narrower Brillouin gain spectrum in frequency domain. Both the theoretical simulation and the experimental results demonstrate that the DSB modulation provides potentially longer sensing distance and higher accuracy in measurement than the SSB modulation in the BOTDA distributed fiber sensor system.

The interlaminar fracture-behavior and toughening mechanisms of new carbon-fiber-reinforced bismaleimide composites

The interlaminar fracture behaviour of carbon fibre-reinforced bismaleimide (BMI) composites prepared by using a new modified BMI matrix has been investigated by various methods. Laminates of three typical stacking sequences were evaluated. Double cantilever beam, end-notch flexure and edge-delamination tension tests were conducted under conventional conditions and in a scanning electron microscope. The strain energy release rates in Mode I and Mode III G(lc) and G(llc), as well as the total strain energy release rate, G(mc), have been determined and found to be higher than those for laminates with an epoxy matrix. Dynamic delamination propagation was also studied. The toughening mechanisms are discussed.