神光Ⅱ装置中空间滤波器系统的稳定性设计与分析

考虑到空间滤波器系统在激光装置中的稳定性要求，分析了影响稳定性的各种因素。对现行装置中的SF4空间滤波器系统进行振动模态测试，初步确定系统的工作状况，并结合振动理论明确系统稳定性的设计参数。利用有限元软件ANSYS对空间滤波器系统及相关的设计进行仿真验证计算。结果表明：SF4系统的一阶固有频率达到83Hz，与实验结果相符合，满足系统稳定性的要求；在系统中引入支撑不但能有效增加系统的刚度，同时能转移系统的振型；系统基础支撑平台的选择要求平台独立，并且选择较低的高度以便于控制上层光学元件的变形；在系统中的引入

Design guidelines and characteristics for a kind of four-layer large flattened mode fibers

A theoretical method to analyze a kind of four-layer large flattened mode (LFM) fibers is presented. The properties of the fiber, including the fundamental and higher-order modal fields, effective area and bending loss are discussed by comparison. At the same time, the reasons for the different characteristics are considered. The obtained results indicate that the effective area of the four-layer LFM fiber is about 1.3 times larger than that of the conventional standard step-index fiber and the fiber can suppress the higher-order modes via bending effectively. The four-layer LFM fiber has less efficient bend-induced filtering ability than the conventional step-index fiber; however, it has more efficient filtering ability than the three-layer LFM fiber. (C) 2007 Elsevier GmbH. All rights reserved.

大模场面积光纤激光器79．4W单横模输出

abstract {A large-mode-area (LMA) multimode fiber before and after coiling was studied contrastively in the experiment. Single-transverse-mode output was achieved when the fiber laser was coiled around a mandrel of 65 mm radius. After coiling, beam quality factor of the laser dropped from 1.24 to 1.06 and slope efficiency dropped from 64.7% to 54.3%. When the launched pump power was 149 W, the corresponding output power was 94.7 W and 79.4 W, respectively. However, the brightness of the coiled fiber laser was 1.15 times that of the uncoiled. Coiled modal losses of different modes were also calculated for the fiber employed in the experiment. The measured results agree well with the calculated ones.}

Efficient excitations of radially and azimuthally polarized Nd 3+:YAG ceramic microchip laser by use of subwavelength multilayer concentric gratings composed of Nb2O5/SiO2

Cylindrical vector beams were produced from laser diode end-pumped Nd:YAG ceramic microchip laser by use of two types of subwavelength multilayer gratings as the axisymmetric-polarization output couplers respectively. The grating mirrors are composed of high- and low-refractive-index (Nb2O5/SiO2) layers alternately while each layer is shaped into triangle and concentric corrugations. For radially polarized laser output, the beam power reached 610mW with a polarization extinction ratio ( PER) of 61: 1 and a slope efficiency of 68.2%; for azimuthally polarized laser output, the beam power reached 626mW with a PER of 58: 1 and a slope efficiency of 47.6%. In both cases, the laser beams had near-diffraction limited quality. Small differences of beam power, PER and slope efficiency between radially and azimuthally polarized laser outputs were not critical, and could be minimized by further optimized adjustment to laser cavity and the reflectances of respective grating mirrors. The results manifested, by use of the photonic crystal gratings mirrors and end-pumped microchip laser configuration, CVBs can be generated efficiently with high modal symmetry and polarization purity. (C) 2008 Optical Society of America.

Ridge optical waveguide in an Er3+/Yb3+ co-doped phosphate glass produced by He+ ion implantation combined with Ar+ ion beam etching

This paper reports on the fabrication and characterization of a ridge optical waveguide in an Er3+/Yb3+ co-doped phosphate glass. The He+ ion implantation (at energy of 2.8 MeV) is first applied onto the sample to produce a planar waveguide substrate, and then Ar+ ion beam etching (at energy of 500 eV) is carried out to construct rib stripes on the sample surface that has been deposited by a specially designed photoresist mask. According to a reconstructed refractive index profile of the waveguide cross section, the modal distribution of the waveguide is simulated by applying a computer code based on the beam propagation method, which shows reasonable agreement with the experimentally observed waveguide mode by using the end-face coupling method. Simulation of the incident He ions at 2.8 MeV penetrating into the Er3+/Yb3+ co-doped phosphate glass substrate is also performed to provide helpful information on waveguide formation.

Optimization of near-field optical field of multi-layer dielectric gratings for pulse compressor

Multi-layer dielectric (MLD) gratings for pulse compressors in high-energy laser systems should provide high diffraction efficiency as well as high laser induced damage thresholds (LIDT). Nonuniform optical near-field distribution is one of the important factors to limit their damage resistant capabilities. Electric field distributions in the gratings and multi-layer film region are analyzed by using Fourier modal method. Optimization of peak electric field in the gratings ridge is performed with a merit function, including both diffraction efficiency and electric field enhancement when the top layer material is HfO2 and SiO2, respectively. A set of optimized gratings parameters is obtained for each structure, which reduce the peak electric field within the gratings ridge to being respective 1.39 and 1.84 times the value of incident light respectively. Finally, we also discuss the effects of gratings refractive index, gratings sidewall angle and incident angle on peak electric field in the gratings ridge. (c) 2006 Elsevier B.V. All rights reserved.

多层介质膜脉冲压缩光栅近场光学特性分析

利用傅里叶模式理论分析了TE波自准直角入射的使用条件下，多层介质膜光栅的光栅区和多层膜区电场分布的特点．分别讨论了HfO2和SiO2为顶层光栅材料时，光栅结构参数对光栅脊峰值电场的影响，结果表明，对于不同膜厚的顶层材料，存在一个最佳膜厚度，使光栅脊峰值电场最小，并且当膜厚增大时，设计大高宽比的光栅可以降低该电场峰值．最后，在大角度条件下使用多层膜光栅也可以降低光栅脊处的峰值电场．

飞秒激光用多层介质膜脉宽压缩光栅的设计

以薄膜光学的干涉理论和衍射光学的傅里叶模式理论为基础，给出了0．8μm飞秒激光器用多层介质膜脉宽压缩光栅的理论设计；设计采用H3L（HL）^9H0．5L2．4H的多层介质膜为基底，当刻蚀后表面浮雕结构的占宽比为0．35，线密度为1480线／mm，槽深为0．2μm，顶层HfO2的剩余厚度为0．15μm时，对于Littrow角度（36．7°）和TE波模式入射的衍射光栅其-1级衍射效率达到95％以上．

Design of high-efficiency diffraction gratings based on total internal reflection for pulse compressor

We present designs of high-efficiency compression grating based on total internal reflection (TIR) for picosecond pulse laser at 1053 nm. The setup is devised by directly etching gratings into the bottom side of a prism so that light can successfully enter (or exit) the compression grating. Dependence of the -1 order diffraction efficiencies on the constructive parameters is analyzed for TE- and TM-polarized incident light at Littrow angle by using Fourier modal method in order to obtain optimal grating structure. The electric field enhancement within the high-efficiency TIR gratings is regarded as another criterion to optimize the structure of the TIR gratings. With the criterion of high diffraction efficiency, low electric field enhancement and sufficient manufacturing latitude, TIR compression gratings with optimized constructive parameters are obtained for TE- and TM-polarized incident light, respectively. The grating for TE-polarized light exhibits diffraction efficiencies higher than 0.95 within 23 nm bandwidth and relatively low square of electric field enhancement ratio of 5.7. Regardless of the internal electric field enhancement, the grating for TM-polarized light provides diffraction efficiencies higher than 0.95 within 42 nm bandwidth. With compact structure, such TIR compression gratings made solely of fused silica should be of great interest for application to chirped pulse amplification (CPA) systems. (c) 2007 Elsevier B.V. All rights reserved.

多层介质膜脉冲宽度压缩光栅与超短脉冲作用时的性能分析

基于啁啾脉冲放大技术的超短脉冲激光系统是提供超快、超强激光的重要途径，具有良好输出波形和高损伤阈值的多层介质膜脉冲宽度压缩光栅是获得高峰值功率脉冲激光的关键。基于傅里叶谱变换方法和严格模式理论，分析了多层介质膜光栅（MDG）在超短脉冲作用下的光学特性。结果表明，当MDG的反射带宽小于具有高斯分布的入射脉冲的频谱宽度时，-1级反射脉冲呈非对称高斯分布，其前沿出现振荡，并且-1级反射脉冲能量开始剧烈下降，讨论了MDG结构参数对其反射带宽的影响。分析了MDG与超短脉冲作用时的近场光分布，对提高其抗激光损伤特性具

反射型导模共振滤波器设计

导模共振滤波器由于其高峰值反射率,低旁带反射,窄带以及带宽可控等优良特性引起了人们极大的关注,采用亚波长光栅的导模共振效应可以实现传统基于高低折射率介质的多层膜滤波器所无法实现的特殊功能,在弱调制模式下,其共振带宽可以被压缩到零点几纳米,但是由于介质表面和空气层的菲涅耳反射,使得偏离或者远离共振区时的反射率偏高,根据等效介质理论,亚波长光栅在远离共振区可以被看为均匀的薄膜,本文通过对导模共振光栅进行单层、双层以及三层抗反射设计,有效的降低了导模共振光栅的旁带反射率,从而在可见光波段获得了性能优良的共振滤波器.

可见光波段双层浮雕型导模共振滤波器设计与分析

基于傅里叶模式理论分析了双层浮雕型导模共振光栅的共振效应,分别讨论了光栅的槽深、剩余厚度、周期以及填充系数对峰值反射率、带宽、旁带反射率的影响.数据计算表明,欠刻蚀情形的误差宽容度远远优于过刻蚀情形,两者在光栅槽深相对误差小于15%的范围内,都能保证共振峰的衍射效率高于99.5%,在相同的误差范围内,共振峰线宽的相对误差将分别达到7%和60%,因此厚度误差集中反映在对共振线宽的改变上.另外,光栅周期和填充系数的变化将明显改变共振峰中心波长和线宽.

A physico-chemical comparative study on extracellular carbohydrate polymers from five desert algae

Hydrodynamic properties of five newly isolated algal extracellular polysaccharides with putative adhesive properties are described, using a combination of size exclusion chromatography, total or 'multi-angle' laser light scattering and analytical ultracentrifugation. The respective polysaccharides had been extracted from four filamentous cyanobacteria: Microcoleus vaginatus, Scytonema javanicum, Phormidium tenue and Nostoc sp. and a coccoid single-cell green. algae Desmococcus olivaceus that had been separated from desert algal crusts of the Chinese Tegger Desert. SEC/MALLS experiments showed that the saccharides had, diverse-weight average molecular weights ranging from 4000 to 250,000 g/mol and all five showed either bi-modal or tri-modal molecular weight distribution profiles. Use of the Mark-Houwink-Kuhn-Sakurada (MHKS) scaling relationship between sedimentation coefficient and (weight average) molecular weight for the five samples, assuming a homologous conformation series revealed an MHKS b exponent of (0.33 +/- 0.04), suggesting a conformation between that of a stiff rod (b similar to 0.18) and a random coil (b similar to 0.4-0.5), i.e. a 'flexible rod' or 'stiff coil'. (C) 2003 Elsevier Ltd. All rights reserved.

HYDROGRAPHIC VARIATIONS IN SIZE STRUCTURE OF PLANKTON BIOMASS IN A CHANGJIANG FLOODPLAIN LAKE

The size structure of the planktonic community in a Changjiang floodplain lake (Lake Chenhu, Hubei, P. R. China) was described for the inundation period of May through September 1983. The modality of the Sheldon-type size distributions changed hydrographically with the spectral profiles being bimodal during low, rising, mid-high and falling water phases, and trimodal soon after filling and shortly before falling. The modal peaks corresponded respectively to the dominant organisms of chlorophytes and nauplii, while the troughs centered on the bacteria and macrocrustacean size classes in the lake. The slope of the normalized biomass spectrum (an index of plankton size distribution) was less than -1.0 for the filling and falling phases or close to -1.0 for the high water period, indicating that the planktonic biomass tended to decrease or evenly distributes across logarithmically ordered size classes, respectively. This observed variation in the size distribution of the plankton community mainly resulted from changes in water levels and contents of particulate inorganic matter (PIM) in the lake.

Integration of a photonic crystal polarization beam splitter and waveguide bend

In this work, we present the design of an integrated photonic-crystal polarization beam splitter (PC-PBS) and a low-loss photonic-crystal 60 waveguide bend. Firstly, the modal properties of the PC-PBS and the mechanism of the low-loss waveguide bend are investigated by the two-dimensional finite-difference time-domain (FDTD) method, and then the integration of the two devices is studied. It shows that, although the individual devices perform well separately, the performance of the integrated circuit is poor due to the multi-mode property of the PC-PBS. By introducing deformed airhole structures, a single-mode PC-PBS is proposed, which significantly enhance the performance of the circuit with the extinction ratios remaining above 20dB for both transverse-electric (TE) and transverse-magnetic (TM) polarizations. Both the specific result and the general idea of integration design are promising in the photonic crystal integrated circuits in the future. (C) 2009 Optical Society of America