Numerical Study on the Spatial and Temporal Characteristics of Water Quality in the Taihu Lake of China

Taihu Lake is the third largest fresh water lake in China. With the fast economic development, abundant industrial and agricultural waste water has been discharged into Taihu Lake, causing the eutrophication of the water quality, which greatly affected the water utility. In the past decades, the treatment of Taihu Lake has witnessed limited success. Therefore, it is practically and theoretically significant to study the eutrophication of Taihu Lake. This research has focused on the issue of water quality including the characteristics of spatial and temporal distributions, and the rules of nutrient diffusion in the Taihu lake area. Based on the monitoring data, the basis distribution characteristics of water quality in Taihu Lake are analyzed. Comparing Taihu Lake with other Lakes shows that one important reason for Taihu eutrophication is the long period of water retention. A transporting and diffusing model of Taihu nutrient is developed by combining with the hydrodynamics model. Using the model, the concentration field of the total phosphorus (TP) and the influence of wind-driven current are numerically investigated, which leads to the conclusion that the flow field has a great influence on the spatial and temporal distributions of TP in Taihu Lake. Furthermore, the effect for improving the water quality by the project of water diversion from the Yangtze River to Taihu Lake was analyzed by simulation. The results demonstrate that short-term water diversion cannot improve the water quality of the heavily-polluted Meiliang Bay and the western bank areas of Taihu Lake.

遮荫与外源脱落酸喷施对青杨(Populus cathayana Rehd.)不同种群抗旱性的影响

杨树具有分布广、适应性强的特征，在生态环境治理和解决木材短缺方面均占有重要位置。青杨(Populus cathayana Rehd.)是青杨派树种的重要成员之一，也是生长较迅速、易繁殖的重要杨树资源。本研究选取了来自不同气候地区的青杨两种群为材料，采用植物生态学、生理学和生物化学的研究方法，系统地研究了青杨对干旱与遮荫、干旱与外源脱落酸(ABA)喷施的生长、形态、生理和生化响应及种群间差异，研究成果可为我国干旱半干旱地区的造林以及生态恢复提供理论依据和科学指导。主要研究结论如下：1.青杨在干旱胁迫下的适应机制为：生长性状及生物量的分配变化：干旱胁迫下虽然植株生长受抑，株高、基茎及各部分生物量都显著减小，但有相对较多的生物量向根部分配，根/冠比以及细/粗根比增加。青杨对干旱胁迫的光合作用表现为：干旱胁迫降低了青杨的净光合速率、蒸腾速率、气孔导度以及光合氮利用效率，提高了瞬时用水效率。干旱还引起了活性氧的产生，使得膜脂过氧化产物丙二醛(MDA)增加，同时也增强了植物抗氧化酶系统(如超氧化物歧化酶(SOD)、过氧化氢酶(CAT)和抗坏血酸过氧化物酶(APX)活性的增加)及非酶系统的能力(如抗坏血酸(AsA)含量的增加)。干旱降低了植物叶片的相对含水量，而促进了渗透调节物质(游离脯氨酸及可溶性糖)的积累，增加了植物的渗调能力。干旱下青杨两种群的内源ABA含量显著增加，碳同位素组分(δ13C)也显著提高。这些结果证明植物遭受干旱胁迫后发生一系列的形态、生理和生化响应，这些变化能提高植物在干旱下的存活和生长能力。2.青杨两种群对干旱胁迫反应的种群差异：与来自湿润地区的汉源种群相比，来自干旱地区的乐都种群在干旱条件下生物量向根系分配的可塑性更强，同时具有更强的抗氧化系统能力，所受到活性氧的伤害也更少，并且累积更多的脯胺酸和ABA，具有更高的δ13C。这些都说明了乐都种群对干旱的适应性比汉源种群更强。两种群对干旱的响应差异应归于它们的用水策略的不同：汉源种群来自湿润地区，采用了耗水型的用水策略，抗旱能力较弱；而乐都种群，来自干旱地区，通常采用节水型的用水策略，有更强的抗旱能力。3.遮荫对青杨两种群抗旱性的影响：遮荫对青杨抗旱性的影响决定于遮荫程度的不同，我们的结果表明中度的遮荫可以有效的提高干旱下植物的生长，对干旱胁迫有明显的缓解作用，具体体现在中度遮荫下受旱植物的叶片相对含水量得到提高，使得植物体内水分状况得到了改善；光合速率并未降低，植物光合氮利用效率增加，说明中度的遮荫并未明显限制植物的碳获得；抗氧化酶活性与膜脂过氧化产物MDA含量的同时降低，说明中度遮荫下所受到的活性氧伤害减少；中度遮荫下的ABA及δ13C的变化也不如在全光下变化明显，这也说明中度遮荫缓解了干旱胁迫。但是重度的遮荫却对干旱胁迫有明显的加剧作用，主要表现在重度遮荫降低了植物的光合速率，严重抑制了植物的生长；同时重度遮荫下脯胺酸含量和抗氧化酶活性的急剧下降，导致了植物渗调能力的下降及膜脂过氧化产物MDA的显著升高；重度遮荫还显著降低了内源ABA的累积和δ13C，降低了植物的抗旱能力。此外，青杨两种群在对干旱和遮荫的响应中，也表现出种群差异。汉源种群，来自湿润且年日照辐射较少的地区，表现出相对更强的耐荫性和需水性。而乐都种群，来自干旱且年日照辐射丰富的地区，表现出相对更强的耐旱性和需光性。这说明了植物对环境胁迫的耐受性是其长期适应原生境的结果，并且来自不同气候地区的两种群在面临环境胁迫时会采取不同的生存策略。4. 外源ABA喷施对青杨两种群抗旱性的影响：外源ABA的喷施可以提高两种群的抗旱性，具体表现为外源ABA喷施促进了青杨根系的生长，显著提高了干旱下植物的根/冠比和细/粗根比，减少了比叶面积；在生理生化方面，外源ABA降低了干旱下植物叶片的气孔导度，降低了蒸腾速率和净光合速率，但提高了瞬时用水效率，提高了叶片的相对含水量，增加了干旱下植物的保水能力。外源ABA进一步增加了干旱下植物内源ABA的积累，促进了植物渗调物质如脯胺酸和可溶性糖的积累，增加了抗氧化酶系统(如SOD、APX、CAT)的活性和非酶系统AsA的含量，降低了活性氧(如超氧阴离子(O2和过氧化氢(H2O2))对植株的伤害。此外，外源ABA还进一步提高了干旱下植物的δ13C，提高了植物的长期用水效率，由此提高了植物的抗旱能力。另一方面，两种群对外源ABA和干旱的响应也有所差别。来自湿润地区的汉源种群，对干旱较为敏感，所受干旱的影响也较大，而外源ABA的喷施对汉源种群抗旱性的提高作用也更为突出。乐都种群，由于其长期适应干旱地区的生长，本身已具有较强的抗旱能力，因此外源ABA喷施对其抗旱性的提高不如对汉源种群的效果明显。由此我们可以得出对于一些抗性弱或干旱敏感的物种或者种群，可以采用外施ABA的方法来提高其抗性。Poplars play an important role in lumber supply, and are important component ofecosystems due to their wide distribution and well adaptation. Populus cathayana Rehd.,which belongs to Populus Sect. Tacamahaca Spach, is one of the most important resources ofpoplars for its fast growth and reproductive. In this study, different populations of P.cathayana were used as experiment material to investigate the adaptability to drought stressand population differences in adaptability, and the effects of shade and exogenous abscisicacid (ABA) application on the drought tolerance. Our results could provide a strongtheoretical evidence and scientific direction for the afforestation, and rehabilitation ofecosystem in the arid and semi-arid area, and provide a strong evidence for adaptivedifferentiation of different populations, and so may be used as criteria for species selectionand tree improvement. The results are as follows:1. A large set of parallel response to drought stress: Drought stress caused pronouncedinhibition of the growth and increased relatively dry matter allocation into the root. For thetwo populations, the shoot height, basal diameter and total biomass were decreased but theroot/shoot ratio and fine root/coarse root ratio were increased under drought conditions；Drought stress caused pronounced inhibition of photosynthesis, decreased the stomatalconductance, transpiration rate, and photosynthetic nitrogen-use efficiency (PNUE) butincreased the instantaneous water use efficiency. Drought significantly improved the levels ofreactive oxygen species and malondialdehyde (MDA) and to induce the entire set ofantioxidative systems including the increase of activities of superoxide dismutase (SOD),ascorbate peroxidase (APX), catalase (CAT) and ascorbate (AsA) content. Drought decreased the leaf relative water content (RWC) but improved the capability of osmotic adjustmentindicated by the higher proline accumulation. Drought also increased the ABA content andcarbon isotope composition (δ13C), which indicating the long period water use efficiency wasimproved under drought. These results demonstrate that there are a large set of parallelchanges in the morphological, physiological and biochemical responses when plants areexposed to drought stress; these changes may enhance the capability of plants to survive andgrow during drought periods.2. Difference in adaptation to drought stress between contrasting populations of P.cathayana: Compared with the Hanyuan population (wet climate), the Ledu population (dryclimate) showed higher root/shoot ratio and water use efficiency, exhibited higherantioxidative systems capability thus resulting in less oxidative damage, accumulated moreABA and free proline content under drought conditions. The results suggested that there weredifferent water-use strategies between the two populations. The Ledu population, whichcomes from dry climate region, with higher drought tolerance, may employ a conservativewater-use strategy, whereas the Hanyuan population, which comes from wet climate, withlower drought tolerance, may employ a prodigal water-use strategy. These variations indrought responses may be used as criteria for species selection and tree improvement.3. The effects of shade on the drought tolerance: The reduction in the availability of lightand water affected the morphological and physiological responses of the two P. cathayanapopulations. In addition, the light environment modified the growth responses of P.cathayana seedlings to varying water environments in different ways depending upon theintensity of the light levels considered. There is an apparent alleviation to drought effects bymoderate shade in P. cathayana seedlings, as indicated by the higher leaf RWC, and unchanged net photosynthesis and PNUE, as well as by the lower antioxditative enzymeactivity, MDA, ABA and δ13C levels, which implied moderate shade did not significantlylimited the carbon acquisition or inhibited the plant growth, but ameliorated the detrimentaleffects of drought. On the other hand, an apparent aggravation to drought effects by severeshade was also observed, as indicated by the pronounced decrease of plant growth and net photosynthesis, the lower total biomass, ABA level, δ13C, free proline content andantioxditative enzyme activity and higher MDA accumulation. By contrast, the twopopulations showed different responses to shade and drought. The Hanyuan population,which comes from a riparian basin having a relatively wet climate and less annual solarradiation, is more sensitive to drought but more tolerant to shade. The Ledu population, whichcomes from a mountainous plateau with less rainfall and with more annual solar radiation, ismore tolerant to drought but more sensitive to shade. The results demonstrated that theendurance of plants to stress is a result of long-term evolution and adaptation to theenvironment, as suggested by the different strategies employed by the P. cathayanapopulations originating from contrasting habitats when they were exposed to drought andshade.4. The effects of exogenous ABA application on the drought tolerance: For bothpopulations under drought conditions tested, exogenous ABA application significantlyimproved the root/shoot ratio, fine root/coarse root ratio, and decreased the specifical leaf area.On the physiological and biochemical traits, exogenous ABA application significantlydecreased stomatal conductance, transpiration rate and net photosythesis but increased theinstance water use efficiency and leaf RWC. On the other hand, exogenous ABA applicationsignificantly increased endogenous ABA, proline, solube sugar and AsA content, as well asSOD, APX and CAT activities, thus reduced the damage of reactive oxygen species. Moreover,the long period water use efficiency as indicated by δ13C was also improved by exogenousABA application. In additionally, there was different responsive between the two populationsto drought and exogenous ABA application. The Hanyuan population, which comes from wetclimate region, is more sensitive to drought, and the effect of exogenous ABA is moreobviously than that in the Ledu population, which comes from dry climate region and is moredrought-responsive. Therefore, we can use exogenous ABA application to improve theresistance of plants, especially for the drought- sensitive species or populations.

非粮原料燃料乙醇发酵关键技术的研究

生物质燃料乙醇是一种高度清洁的交通液体燃料，是减少温室气体排放，缓解大气污染的最佳技术选择。以非粮原料生产燃料乙醇可以在进行能源生产的同时保证粮食安全，有利于产业的可持续发展。在众多的非粮原料中，甘薯是我国开发潜力最大的生物质能源作物之一。我国占世界甘薯种植总面积和产量的90％。同时，甘薯的单位面积燃料乙醇产量远大于玉米和小麦。其成本是目前酒精中最低廉的，因此利用甘薯生产乙醇是发展生物质燃料乙醇的首要选择。目前采用薯类全原料主要采用分批发酵生产乙醇，其技术水平低，发酵强度低，一般在0.7－2.5g/（L•h），乙醇浓度低，甘薯发酵乙醇为6－8％(v/v)，能耗高，环境负荷大，污染严重。针对上述问题，本文从菌株选育、原料预处理、中试放大、残糖成分分析等方面进行研究。 为了研究乙醇发酵生产规模扩大过程中，大型发酵罐底部高压条件下，CO2对酵母乙醇发酵的影响，我们通过CO2 加压的方法进行模拟试验，研究结果表明，发酵时间随压强的升高而逐渐延长，高压CO2 对乙醇发酵效率影响不大，在0.3 MPa 以下时，发酵效率均可达到90%以上。高压CO2 对发酵的抑制作用是高压和CO2 这两个因素联合作用的结果。高压CO2 条件下，酵母胞外酶和胞内重要酶类的酶活均表现出特征性。0.2 MPa 下，酶活性的变化趋势和0.1 MPa 条件下的较为一致。而0.3 MPa 下的酶活变化趋势与0.4 MPa 下的酶活更为接近。通过全基因表达分析发现在CO2 压力为0.3 MPa 下，乙醇发酵途径中多个基因表达量下调，同时海藻糖合成酶和热激蛋白基因表达量上调。 筛选耐高温的乙醇酵母菌株能够解决糖化温度和发酵温度不协调的矛盾，实现真正意义上的边糖化边发酵。高温发酵还能够降低发酵时的冷却成本，实现乙醇的周年生产。本研究筛选出一株高温发酵菌株Y-H1，进而我们对该菌株的胞外酶和胞内乙醇代谢重要酶类的酶活性进行了分析。结果表明Y-H1 能够在40 ℃条件下正常进行乙醇发酵，发酵33h，最终乙醇浓度达到10.7%（w/w），发酵效率达到90%以上。同时发酵液最终pH 在3.5 左右，显示菌株具有一定的耐酸性能力。同时观察到40 ℃下，菌株的胞外酶和胞内乙醇代谢重要酶类的酶活性发生了变化，乙醇发酵途径中关键酶基因表达下调，而海藻糖合成酶与热激蛋白基因表达量上调，这些结果为进一步研究酵母菌耐热调控机理提供了依据。 糖蜜是一种大规模工业生产乙醇的理想原料，本研究利用选育高浓度乙醇发酵菌株结合配套的发酵稳定剂，研究了糖蜜高浓度乙醇发酵情况。结果表明采用冷酸沉淀预处理糖蜜溶液，采用分批补料的发酵方式，乙醇浓度最高达到了10.26% (w/w)，发酵时间为42 h。同时观察到在糖蜜发酵中，乙醛含量与乙醇浓度存在一定的相关性。 快速乙醇发酵对于缩短乙醇生产周期、降低乙醇生产成本、减少原料腐烂损失具有重要意义。本研究诱变和筛选得到了一株快速乙醇发酵菌株10232B。在优化后的发酵条件下，采用10L 发酵罐进行分批乙醇发酵，经过18h,乙醇的最终浓度达到88.5g/L,发酵效率93.6%，平均乙醇生产速度达到4.92 g/L/h。此菌株在保持较高乙醇生产浓度的同时，拥有快速生产乙醇的能力，适合作为快速乙醇发酵生产菌种。 由于鲜甘薯具有粘度大的特点，传统液化糖化处理很难在短时间内充分糖化原料；高粘度的醪液也难以进行管道输送，容易堵塞管路；同时，也会降低后续的乙醇发酵效率。 本文采用了快速粘度分析法对鲜甘薯糊化粘度特性进行了分析，进而对预处理条件进行了研究，在最佳预处理条件下，糖化2h 后，醪液葡萄糖值最高可达99.3，粘度4.5×104 mPa.s，而采用传统糖化工艺，醪液DE 值仅为85.8，粘度大于1.0×105 mPa.s。 此预处理方法也可用于快速糖化不加水的醪液。后续的乙醇发酵试验表明，通过此预处理方法获得的糖化醪液对乙醇发酵无负面影响。 在前期已实现了实验室水平的鲜甘薯燃料乙醇快速乙醇发酵基础上，进一步将发酵规模扩大到500L，在中试水平上对甘薯乙醇发酵进行了研究。结果表明在500L 中试规模，采用边糖化边发酵（SSF）工艺，在料液比为3∶1，发酵醪液最高粘度为6×104mPa.s 条件下，发酵37h，乙醇浓度达到了12.7%（v/v），发酵效率91%，发酵强度为2.7 g/（L•h）。与目前国内的薯类乙醇发酵生产技术水平具有明显的优越性。 为研究甘薯、木薯乙醇发酵中残糖的组成，采用了高效液相色谱—蒸发光散射检测法，对乙醇发酵残糖进行了分析。结果表明，甘薯、木薯乙醇发酵残糖均为寡聚糖，主要由葡萄糖、木糖、半乳糖、阿拉伯糖和甘露糖构成。随着发酵时间延长，寡聚糖中的葡萄糖、半乳糖、甘露糖可被缓慢的水解释放。提高糖化酶量仅在一定程度上降低残糖，过量的糖化酶反而会导致残糖增加。同时发现3, 5-二硝基水杨酸法不能准确测定甘薯、木薯乙醇发酵中的残总糖含量。进一步筛选了两株残糖降解菌株，对甘薯乙醇发酵残糖的降解利用率均达到了40%以上，而且还能显著降低发酵醪液粘度。经形态学和rRNA ITS 序列分析，确定这两株菌分别属于为木霉属和曲霉属黑曲霉组。 通过对以甘薯原料为代表的非粮原料发酵技术研究开发，以期形成乙醇转化率高，能耗低，生产效率高、季节适应性好，原料适应性广，经济性强，符合清洁生产机制的燃料乙醇高效转化技术，为具有我国特色的燃料乙醇发展模式提供技术支持。 Sweet potato is one of the major feedstock for the fuel ethanol production in China. The planting area and the yield in China take 90% of the world. Sweet potato is an efficient kind of energy crops. The energy outcome per area is higher than corn or wheat. And the manufacture cost of ethanol is the lowest, compared with corn and wheat. So sweet potato is the favorable crop for the bioethanol production in China. However, the low-level fermentation technology restricts the development of ethanol production by sweet potato, including slow ethanol production rate, low ethanol concentration and high energy cost. To solve these problems, we conducted research on the strain breeding, pretreatment, pilot fermentation test and residual saccharides analysis. To study the impact of hyperbaric condition at bottom of the large fermentor on yeast fermentation, high pressure carbon dioxide (CO2) was adopted to simulate the situation. The results showed that the fermentation was prolonged with the increasing pressure. The pressure of CO2 had little impact on the ethanol yield which could reach 90% under the pressure below 0.3 MPa. The inhibition was combined by the high pressure and CO2. Under the high CO2 pressure, the extracellular and important intracellular enzyme activities were different from those under normal state. The changes under 0.1 MPa and 0.2 MPa were similar. The changes under 0.3 MPa were closer to those under 0.4 MPa. The application of thermotolerance yeast could solve the problem of the inconsistent temperature between fermentation and saccharificaton and fulfill the real simultaneous saccharification and fermentation. And it could reduce the cooling cost. A thermotolerance strain Y-H1 was isolated in our research. It gave high ethanol concentration of 10.7%（w/w）at 40 ℃ for 33 h. The ethanol yield efficiency was over 90%. At 40 ℃, the extracellular and important intracellular enzyme activities of Y-H1 showed the difference with normal state, which may indicate its physiological changes at the high temperature. Molasses is another feedstock for industrial ethanol production. By our ethanol-tolerance strain and the regulation reagents, the fermentation with high ethanol concentration was investigated. In fed-batch mode combined with cold acid deposition, the highest ethanol concentration was 10.26% (w/w) for 42h. The aldehyde concentration in fermentation was found to be related to ethanol concentration. The development of a rapid ethanol fermentation strain of Zymomonas mobilis is essential for reducing the cost of ethanol production and for the timely utilization of fresh material that is easily decayed in the Chinese bioethanol industry. A mutant Z. mobilis strain, 10232B, was generated by UV mutagenesis. Under these optimized conditions, fermentation of the mutant Z. mobilis 10232B strain was completed in just 18 h with a high ethanol production rate, at an average of 4.92 gL-1h-1 per batch. The final maximum ethanol concentration was 88.5 gL-1, with an ethanol yield efficiency of 93.6%. This result illustrated the potential use of the mutant Z. mobilis 10232B strain in rapid ethanol fermentation in order to help reduce the cost of industrial ethanol production. As fresh sweet potato syrup shows high viscosity, it is hard to be fully converted to glucose by enzymes in the traditional saccharification process. The high-viscosity syrup is difficult to be transmitted in pipes, which may be easily blocked. Meanwhile it could also reduce the later ethanol fermentation efficiency. To solve these problems, effects of the pretreatment conditions were investigated. The highest dextrose equivalent value of 99.3 and the lowest viscosity of 4.5×104 mPa.s were obtained by the most favorable pretreatment conditions, while those of 85.8 and over 1.0×105 mPa.s was produced by traditional treatment conditions. The pretreatment could also be applied on the material syrup without adding water. The later experiments showed that the pretreated syrup had no negative effect on the ethanol fermentation and exhibited lower viscosity. The fuel ethanol rapid production from fresh sweet potato was enlarged in the 500L pilot scale after its fulfillment on the laboratory level. The optimal ratio of material to water was 3 to 1 in 500L fermentor. With low-temperature-cooking (85 ℃) using SSF, the Saccharomyces cerevisiae was able to produce ethanol 97.44 g/kg for 37h, which reached 92% of theoretical yield. The average ethanol production rate was 4.06 g/kg/h. And the maximum viscosity of syrup reached 6×104mPa.s. The results showed its superiority over current industrial ethanol fermentation. The compositions of the residual saccharides in the ethanol fermentation by sweet potato and cassava were analyzed by high performance liquid chromatography coupled with evaporative light-scattering detector. The results showed that all the residual saccharides were oligosaccharides, mainly composed of glucose, xylose, galactose, arabinose and mannose. The glucose, galactose and mannose could be slowly hydrolyzed from oligosaccharides in syrup during a long period. To increase the glucoamylase dosage could lower the residual saccharides to a certain extent. However, excess glucoamylase dosage led to more residual saccharides. And the method of 3, 5-dinitrosalicylic acid could not accurately quantify the residual total saccharides content. Two residual saccharides degrading strains were isolated, which could utilize 40% of total residual saccharide and lower the syrup viscosity. With the analysis of morphology and internal transcribed spacer sequence, they were finally identified as species of Trichoderma and Aspergillus niger.

黄土高原灌木林地水分环境特性研究

通过对黄土高原试验示范区的多年定位观测试验 ,并结合调查数据 ,分析了该区灌木林地的土壤水分循环过程 ,大气降水分配特点 ,揭示了灌木林蒸腾耗水特征 ,以及土壤水分动态趋势 ,总结了沙棘、柠条灌木林地土壤水分平衡规律 ,从而为黄土高原绿化、灌木林的合理布局和经营提供了一定的科学依据。

Radiation-use efficiency and the harvest index of winter wheat at different nitrogen levels and their relationships to canopy spectral reflectance

Radiation-use efficiency (RUE, g/MJ) and the harvest index (HI, unitless) are two helpful characteristics in interpreting crop response to environmental and climatic changes. They are also increasingly important for accurate crop yield simulation, but they are affected by various environmental factors. In this study, the RUE and HI of winter wheat and their relationships to canopy spectral reflectance were investigated based on the massive field measurements of five nitrogen (N) treatments. Crop production can be separated into light interception and RUE. The results indicated that during a long period of slow growth from emergence to regreening, the effect of N on crop production mainly showed up in an increased light interception by the canopy. During the period of rapid growth from regreening to maturity, it was present in both light interception and RUE. The temporal variations of RUEAPAR (aboveground biomass produced per unit of photosynthetically active radiation absorbed by the canopy) during the period from regreening to maturity had different patterns corresponding to the N deficiency, N adequacy and N-excess conditions. Moreover, significant relationships were found between the RUEAPAR and the accumulative normalised difference vegetation index (NDVI) in the integrated season (R-2 = 0.68), between the HI and the accumulative NDVI after anthesis (R-2 = 0.89), and between the RUEgrain (ratio of grain yield to the total amount of photosynthetically active radiation absorbed by the canopy) and the accumulative NDVI of the whole season (R-2 = 0.89) and that after anthesis (R-2 = 0.94). It suggested that canopy spectral reflectance has the potential to reveal the spatial information of the RUEAPAR, HI and RUEgrain. It is hoped that this information will be useful in improving the accuracy of crop yield simulation in large areas.

Time-resolved synchrotron SAXS observations on sheared syndiotactic poly(propylene) crystallization process

The in situ crystallization kinetics of syndiotactic poly(propylene) (sPP) has been investigated by synchrotron small-angle X-ray scattering (SAXS). The structure evolutions during the isothermal crystallization of sPP with different shear rates have been observed. The results show that shear accelerates the process of crystallization kinetics. Even under low shear rate, the lamellae can be distinctly oriented. In contrast, the lamellar parameters such as the long period, lamellar thickness, and the scattering invariant 0 can change obviously only under high shear rate.

Synchrotron investigation on the sheared structure evolution of syndiotactic polypropylene crystallization process

The final structure of molten syndiotactic polypropylene (sPP) sheared under different conditions was investigated by synchrotron small-angle x-ray scattering (SAXS) and wide-angle x-ray diffraction (WAXD) techniques to elucidate the shear effects on sPP crystalline structure. The results obtained from the WAXD show that there is no variation on crystalline form but a little difference on the orientation of the 200 reflection. The SAXS data indicate that the lamellar thickness and long period have not been affected by shear but the lamellar orientation is dependent on shear. The experimental data of sPP crystallization from sheared melt may indicate a mesophase structure that is crucial to the shear effects on the final polymer multiscale crystalline structures.

The Study of Electroactive Block Copolymer Containing Aniline Pentamer Isolated from Different Solvents

For the films and powder of polymers containing conductive oligomer are usually obtained from solution, the choice of better solvents for the regular arrangement of oligomers is very important for the higher conductivity. Because of the poor solubility of the oligomers, it is difficult to study the arrangement directly in most common solvents, so, we synthesized a triblock copolymer, mPEG2k-aniline pentamer-mPEG2k, as the model to investigate the arrangement-solvent relationship. For the poor solubility of the AP block in common solvents, the copolymer self-assembled into spheric micelles in toluene and into lamellar crystals in water and THF. The crystallinity (X-c) and crystallization temperature (T-c) values of mPEG blocks in powders prepared from different solvents differed obviously, which may be the effect of different self-assembled structures. From the two-phase model of one-dimensional electron density correlation function of SAXS, the long period of copolymer prepared from THF was presumably equal to the long period of pure mPEG plus the chain length of AP, which demonstrates that the AP blocks arrange regularly in the noncrystalline regions.

Study on crystallization of poly(epsilon-caprolactone) in poly(epsilon-caprolactone)/poly(vinyl methyl ether) blends

The crystallization behaviors of poly( E-caprolactone) (PCL) in poly(epsilon-caprolactone) (PCL) and poly(vinyl methyl ether) (PVME) blends were investigated by POM, DSC, WAXD, SAXS. POM results indicated that spherical crystal morphology was present during isothermal process, and the spheric growth rates were reduced with increasing the contents of PVME in PCL/PVME blends. It was found that the crystallinity of PCL in the blends remained almost constant regardless of the blend composition, but it was dependent on preparation technique. Solution-crystallization was found to be a technique capable of increasing crystallinity levels for some compositions. The melting behavior of the blends is a rather complex process. Both solution-crystallized samples and isothermal-crystallized samples exhibited a single endotherm. Oppositely, melting-crystallized samples exhibited dual-melting endotherms whose mangnitudes vary with blend compositions. On the basis of WAXD and SAXS experiments, it is found that the crystal structure is unchanged, but the long period increases with increasing the content of PVME because of the thickening of the amorphous layers.

Thermal and crystallization behaviors of polyethylene blends synthesized by binary late transition metal catalysts combinations

A series of reactor blends of linear and branched polyethylenes have been prepared, in the presence of modified methylaluminoxane, using a combination of 2,6-bis[1(2,6-dimethyphenylimino) pyridyl]-cobalt(II) dichloride (1), known as an active catalyst for producing linear polyethylene, and [1,4-bis(2,6-diidopropylphenyl)] acenaphthene diimine nickel(II) dibromide (2), which is active for the production of branched polyethylene. The polymerizations were performed at various levels of catalyst feed ratio at 10 bar. The linear correlation between catalyst activity and concentration of catalyst 2 suggested that the catalysts performed independently from each other. The weight-average molecular weights ((M) over bar (w)), crystalline structures, and phase structures of the blends were investigated, using a combination of gel permeation chromatography, differential scanning calorimetry, wide-angle X-ray diffraction, and small angle X-ray scattering techniques. It was found that the polymerization activities and MWs and crystallization rate of the polymers took decreasing tendency with the increase of the catalyst 2 ratios, while melting temperatures (T-m), crystalline temperatures (T,), and crystalline degrees took decreasing tendency. Long period was distinctly influenced by the amorphous component concentration.

Effect of crystallization on the lamellar orientation in thin films of symmetric poly(styrene)-b-poly(L-lactide) diblock copolymer

The effect of crystallization on the lamellar orientation of poly( styrene)-b-poly(L-lactide) (PS-PLLA) semicrystalline diblock copolymer in thin films has been investigated by atomic force microscopy (AFM), transmission electronic microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). In the melt state, microphase separation leads to a symmetric wetting structure with PLLA blocks located at both polymer/substrate and polymer/air interfaces. The lamellar period is equal to the long period L in bulk determined by small-angle X-ray scattering (SAXS). Symmetric wetting structure formed in the melt state provides a model structure to study the crystallization of PLLA monolayer tethered on glassy (T-c < T-g,T-PS) or rubber (T-c > T-g,T-PS) PS substrate. In both cases, it is found that the crystallization of PLLA results in a "sandwich" structure with amorphous PS layer located at both folding surfaces. For T-c <= T-g,T- PS, the crystallization induces a transition of the lamellar orientation from parallel to perpendicular to substrate in between and front of the crystals. In addition, the depletion of materials around the crystals leads to the formation of holes of 1/2 L, leaving the adsorbed monolayer exposure at the bottom of the holes.

Composition dependence of the crystallization behavior and morphology of the poly(ethylene oxide)-poly(epsilon-caprolactone) diblock copolymer

The crystallization behavior and morphology of the crystalline-crystalline poly(ethylene oxide)-poly(epsilon-caprolactone) diblock copolymer (PEO-b-PCL) was studied by differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD), Fourier transform infrared spectroscopy (FTIR), small-angle X-ray scattering (SAXS), and hot-stage polarized optical microscope (POM). The mutual effects between the PEO and PCL blocks were significant, leading to the obvious composition dependence of the crystallization behavior and morphology of PEO-b-PCL. In this study, the PEO block length was fixed (M-n = 5000) and the weight ratio of PCL/PEO was tailored by changing the PCL block length. Both blocks could crystallize in PEO-b-PCL with the PCL weight fraction (WFPCL) of 0.23-0.87. For the sample with the WFPCL of 0.36 or less, the PEO block crystallized first, resulting in the obvious confinement of the PCL block and vice versa for the sample with WFPCL of 0.43 or more. With increasing WFPCL, the crystallinity of PEO reduced continuously while the variation of the PCL crystallinity exhibited a maximum. The long period of PEO-b-PCL increased with increasing WFPCL from 0.16 to 0.50 but then decreased with the further increase of WFPCL due to the interaction of the respective variation of the thicknesses of the PEO and PCL crystalline lamellae.

Miscibility and crystallization behavior of poly(3-hydroxyvalerate-co-3-hydroxyvalerate)/poly(propylene carbonate) blends

Blends of synthetic poly(propylene carbonate) (PPC) with a natural bacterial copolymer of 3-hydroxybutyrate with 3-hydroxyvalerate (PHBV) containing 8 mol % 3-hydroxyvalerate units were prepared with a simple casting procedure. PPC was thermally stabilized by end-capping before use. The miscibility, morphology, and crystallization behavior of the blends were investigated by differential scanning calorimetry, polarized optical microscopy, wide-angle X-ray diffraction (WAXD), and small-angle Xray scattering (SAXS). PHBV/PPC blends showed weak miscibility in the melt, but the miscibility was very low. The effect of PPC on the crystallization of PHBV was evident. The addition of PPC decreased the rate of spherulite growth of PHBV, and with increasing PPC content in the PHBV/PPC blends, the PHBV spherulites became more and more open. However, the crystalline structure of PHBV did not change with increasing PPC in the PHBV/PPC blends, as shown from WAXD analysis. The long period obtained from SAXS showed a small increase with the addition of PPC.

Microstructure analysis of nylon 66 by WAXD and SAXS

The analysis of the small angle X-ray scattering (SAXS) data was based upon particle characteristic function, one-dimensional electron-density correlation function and particle distribution function. The microstructure of nylon 66 with different degrees of crystallinity was studied by means of X-ray scattering method. The radius of gyration R-g, the Porod radius R-p, the thickness of crystalline region L-c the thickness of non-crystalline region L-n, the thickness of interphase region d(tr), the long period L, the semiaxises of particles (a, a, b), the distribution of the particle sizes and the scattering invariant were calculated. The results indicate that there was a significant interphase region between the crystalline region and the non-crystalline region. and its content (W-t,W-x) should not be neglected in comparison with that of crystalline region W-c,W-x. The morphology of nylon 66 prepared by isothermal crystallization at a high temperature was mainly a lamellar structure, while the spherical crystals dominated in the quenched sample. The size of the particles in the quenched sample was smaller than that of those in the isothermally crystallized sample. and the distribution of the particle sizes in the isothermally crystallized sample was wider.

Influence of annealing on structure of Nylon 11

Differential scanning calorimeter (DSC), wide-angle X-ray diffraction (WAXD), small-angle X-ray scattering (SAXS), and density techniques have been used to investigate the structural parameters of the solid state of Nylon 11 annealed at different temperatures. The equilibrium heat of fusion Delta H-m(0) and equilibrium melting temperature T-m(0) were estimated to be 189.05 J g(-1) and 202.85 degrees C respectively by using the Hoffman-Weeks approach. The degree of crystallinity (W-c,W-x) ranged approximately 24-42% was calculated by WAXD and compared with those by calorimetry (W-c,W-h) and density (W-c,W-d) measurements. The radius of gyration R-g, crystalline thickness L-c, noncrystalline thickness L-a, long period L, semiaxes of the particles (a, b), electron-density difference between the crystalline and noncrystalline regions eta(c) - eta(a), and the invariant Q increased with increasing annealing temperature. The analysis of the SAXS data was based upon the particle characteristic function and the one-dimensional electron-density correlation function. An interphase region existed between the crystalline and noncrystalline region with a clear dimension of about 2 nm for semicrystalline Nylon 11. Instead of the traditional two-phase model, a three-phase model has been proposed to explain these results by means of SAXS.