Origin of flat-band voltage sharp roll-off in metal gate/high-k/ultrathin- SiO2/Si p-channel metal-oxide-semiconductor stacks

The origin of the flat band voltage roll-off (V-FB roll-off) in metal gate/high-k/ultrathin-SiO2/Si metal-oxide-semiconductor stacks is analyzed and a model describing the role of the dipoles at the SiO2/Si interface on the V-FB sharp roll-off is proposed. The V-FB sharp roll-off appears when the thickness of the SiO2 interlayer diminishes to below the oxygen diffusion depth. The results derived using our model agree well with experimental data and provide insights to the mechanism of the V-FB sharp roll-off.

Two-stage photo-biological production of hydrogen by marine green alga Platymonas subcordiformis

A marine green alga, Platymonas subcordiformis, was demonstrated to photobiologically evolve hydrogen (H-2) after the first stage of photosynthesis, when subjected to a two-phase incubation protocol in a second stage of H2 production: anaerobic incubation in the dark followed by the exposure to light illumination. The anaerobic incubation induced hydrogenase activity to catalyse H? evolution in the following phase of light illumination. H,) evolution strongly depended upon the duration of anaerobic incubation, deprivation of sulphur (S) from the medium and the medium pH. An optimal anaerobic incubation period of 32 h gave the maximum H2 evolution in the second phase in the absence of sulphur. Evolution of H,) was greatly enhanced by 13 times when S was deprived from the medium. This result suggests that S plays a critical role in the mediation of H-2 evolution from R subcordiformis. A 14-fold increase in H-2 production was obtained when the medium pH increased from 5 to 8; with a sharp decline at pH above eight. H-2 evolution was enhanced by 30-50% when supplementing the optimal concentrations of 25 mM acetate and 37.5 mM glucose. (C) 2003 Elsevier B.V. All rights reserved.

Electron-beam irradiation on poly(propylene carbonate) in the presence of polyfunctional monomers

Poly(propylene carbonate) (PPC) showed predominantly degradation under electron-beam irradiation, accompanied by deterioration of its mechanical performance due to sharp decrease of the molecular weight. Crosslinked PPC was prepared by addition of polyfunctional monomer (PFM) to enhance the mechanical performance of PPC. When 8 wt% of PFM like triallyl isocyanurate (TAIL) was added, crosslinked PPC with a gel fraction of 60.7% was prepared at 50 kGy irradiation dose, which showed a tensile strength at 20 degrees C of 45.5 MPa, whereas it was only 38.5 MPa for pure PPC. The onset degradation temperature (T-i) and glass transition temperature (T-g) of this crosslinked PPC was 246 degrees C and 45 degrees C, respectively, a significant increase related to pure PPC of 211 degrees C and 36 C. Therefore, thermal and mechanical performances of PPC could be improved via electron-beam irradiation in the presence of suitable PFM.

Mechanical and thermal properties of high-density polyethylene toughened with glass beads

Glass beads were used to improve the mechanical and thermal properties of high-density polyethylene (HDPE). HDPE/glass-bead blends were prepared in a Brabender-like apparatus, and this was followed by press molding. Static tensile measurements showed that the modulus of the HDPE/glass-bead blends increased considerably with increasing glass-bead content, whereas the yield stress remained roughly unchanged at first and then decreased slowly with increasing glass-bead content. Izod impact tests at room temperature revealed that the impact strength changed very slowly with increasing glass-bead content up to a critical value; thereafter, it increased sharply with increasing glass-bead content. That is, the lzod impact strength of the blends underwent a sharp transition with increasing glass-bead content. It was calculated that the critical interparticle distance for the HDPE/glass-bead blends at room temperature (25degreesC) was 2.5 mum. Scanning electron microscopy observations indicated that the high impact strength of the HDPE/glass-bead blends resulted from the deformation of the HDPE matrix. Dynamic mechanical analyses and thermogravimetric measurements implied that the heat resistance and heat stability of the blends tended to increase considerably with increasing glass-bead content.

Study on the kinetics of ferrocene derivatives in polymer electrolyte/electrode interface at microelectrode

Heterogeneous electron transfer rate constants (k(s)) and diffusion coefficients (D) of the ferrocene and its derivatives. in a new synthetic comb polymer solvent, poly(dimethylsiloxane-g-monomethylether polyethylene glycol) (SCP), and several other polymer solvents were estimated by using microelectrodes. Also, the influence of various supporting electrolytes on k(s) and D of ferrocene was studied. It was shown that k(s) and D of ferrocene decreased with increasing anionic size of the supporting electrolyte, but k(s) tended to increase with increasing radius of the solvated cation. Also, the cationic size of the supporting electrolytes had little effects on D. The values of k(s) and D for the ferrocene derivatives in the polymer solvents were in sharp contrast to those in monomeric solvents. Thus. the k(s) values were proportional to D in the polymer solvents. which indicates that solvent dynamics control of the electrode reaction. The values of k(s) and D of ferrocene in SCP were larger than those in other polymer solvents indicating that SCP is a good polymer solvent. (C) 2000 Elsevier Science B.V. All rights reserved.

Evaluation of bond covalency and bond valence in Sr-doped perovskite-type compounds

Formulas for decomposing of complex crystals to a sum of binary crystals are described and applied to the study of bond covalency in La1-xSrxFeO3 (0.0 less than or equal to x less than or equal to 0.9) and Ca1-xSrxMnO3 (0.0 less than or equal to x less than or equal to 0.5). The bond valence is treated by bond-valence sums scheme. The results indicate that, for both compounds, with the increasing doping level, the bond covalency and bond valence show the same trend, namely, larger bond covalency corresponds to higher bond valence. For La1-xSrxFeO3, with the increase of doping level, the bond covalency of La-O, Ca-O decreases in the orthorhombic (0.0 less than or equal to x less than or equal to 0.2) and rhombohedral (0.4 less than or equal to x less than or equal to 0.7) systems, then increases slightly for the cubic (0.8 less than or equal to x less than or equal to 0.9) system, but that of Fe-O increases for all crystal systems. A sharp decrease in bond covalency was observed where the crystal changes from orthorhombic to rhombohedral, while a smooth trend was seen for the rhombohedral-to-cubic transition. On the other hand, for orthorhombic Ca1-xSrxMnO3, the bond covalency of Ca-O, Sr-O, and Mn-O (4-coordinate site) decreases with the increasing doping level, that of Mn-O (2-coordinate site) increases.

STRUCTURE OF MESOMORPHIC FORM OF ISOTACTIC POLYPROPYLENE

The structure of quenched isotactic polypropylene (iPP) films, including samples etched with fuming nitric acid (FNA), has been studied by infrared (IR) spectra, wide-angle x-ray diffraction (WAXD), small-angle x-ray scattering (SAXS), and differential scanning calorimetry (DSC) measurements. The changes of IR, SAXS, DSC, and WAXD results induced by annealing for etched samples have been compared with those for unetched ones. The IR absorbance spectrum of the quenched iPP etched by FNA did not change. In addition, the SAXS intensity did not increase when these samples were annealed, indicating that the total (IR) crystallinity (i.e., the content of chain segments in the helical conformations) of the etched samples does not increase. However, WAXD patterns of the samples changed in a manner similar to those of the unetched one, from the original two blurred diffraction peaks to the sharp crystal patterns of alpha-form iPP, suggesting that the mesomorphic (or liquid crystal-like) phase has reorganized to alpha-form crystals. It is concluded that the change of WAXD of quenched iPP films during annealing results mainly from transformation of order in the mesomorphic phase, rather than only from an increase of crystal size. In other words, mesomorphic-form iPP is not constituted by any known crystals (such as alpha or beta crystals) in small sizes; its WAXD pattern reflects truly the degree of order in the mesomorphic phase.

History and variability of Asian interior aridity recorded by eolian flux in the Chinese Loess Plateau during the past 7 Ma

Eolian flux in the Chinese Loess Plateau was reconstructed by measuring the dry bulk density and CaCO3 content of the late Cenozoic loess-paleosol-red clay sequences in the Lingtai profile. Comparison of eolian flux variation between the Lingtai profile and the ODP sites 885/886 in the North Pacific shows a significant wet-dry variability in addition to a gradual drying trend in the dust source regions in interior Asia. Especially, the increase of eolian fluxes from both continental and pelagic eolian sediments indicates a sharp drying of the dust source regions between 3.6 and 2.6 MaBP, which might be attributed to the tectonic uplift of the Tibetan Plateau, which cut down the moisture input to the interior Asia. The average value and variability of eolian flux are higher after 2.6 MaBP than before, which may be related to the Quaternary climatic fluctuations on the glacial-interglacial timescale after the commencement of major Northern Hemisphere Glaciations. The eolian fluxes of the Lingtai profile and Core V21-146 in northwest Pacific show a synchronous variation on the 10(4)-10(5) a timescale, indicating that the flux variations from both continental and marine records are closely correlated to the Quaternary climatic fluctuation forced by the ice volume changes on a global scale.

A preliminary study on thermoluminescence characteristics of sediments from the North Pacific

Thirty-eight surficial deposit samples were collected from the equatorial North Pacific, and the natural thermoluminescence (TL) characteristics of both bulk and clay fraction samples ( < 2 mu m fractions) were studied by the FJ427 - Al automatic TL Dosimeter for the first time. With the measurements of clay mineral composition, element composition by XRD and ICP, the correlations between TL intensity and sedimentary environment proxies were analyzed, such as water depth, ratio of FeO to Fe2O3 contents, LOI, and major clay mineral concentration, and it was found the bulk sample's TL signal was stronger than the clay ones. Usually, increase in the clay components may result in the decrease of TL intensity. From the shape of TL curves, the pelagic sediments can be divided into two groups: the majority group has two glow peaks, in general, the first peak is broad and flat, but the second narrow and sharp; the minority group only has a single peak because the first is absent. The peak centers of TL curves are almost fixed, falling in the temperature sections 230 similar to 260 and 390 similar to 405 degrees C respectively. Lorentz model packed in the Origin 7.5 was chosen to deal with the TL curves. From the processing results, three parameters ( H, C and A), corresponding to the height, center, and kurtosis of TL curve, were obtained to describe the curve characteristics. The correlations between TL curve parameters and sedimentary environment proxies were also calculated. On the basis of the above work, the relationship between TL characteristics and sediment type, mineral composition, sedimentary environment of surface sediments was discussed in the study area, and a conclusion is: sediments from the environment of shallower water, higher organic contents and weaker reductivity have stronger TL signals.

Digestive gut structure and activity of protease, amylase, and alkaline phosphatase in Calanus sinicus during summer in the Yellow Sea and the East China Sea

Calanus sinicus aggregate at the depth of 40-60 m (ambient temperature is 16 degreesC) in the waters of the continental shelf of the Yellow Sea during summer. in animals found in near shore regions, there are changes in digestive gut cells structure, digestive enzyme activity (protease, amylase), and tissue enzyme (alkaline phosphatase (ALP)), which may represent adaptations by this cold-water animal to a sharp seasonal increase in temperature of 6-23 degreesC. The activities of the digestive enzymes (protease and amylase) are very low in animals at stations near the estuary of Yangtse River, whereas they are relatively high in animals at stations in the central Yellow Sea, During summer, B-cells of the intestine and the villi intestinalis disappear in animals that do not feed at stations near the estuary of the Yangtse River. Respiration rates were undetectable or quite low during summer in C. sinicus from stations near the estuary of the Yangtse River, whereas they were relatively high at stations in the central Yellow Sea. Based upon the morphological characteristics of the digestive gut structure, enzyme levels, respiration rates, and the distribution of C. sinicus, we concluded that C. sinicus might be dormant during summer in the near shore areas of the East China Sea while remaining active in the central Yellow Sea. (C) 2002 Elsevier Science B.V. All rights reserved.

Influence of lanthanum on the accumulation of trace elements in chloroplasts of cucumber seedling leaves

Influence of La3+ on the accumulation of trace elements (Se-75, Co-56, Rb-83, V-48, (95)mTc, and Ga-67) in chloroplasts of cucumber seedling leaves was studied by a radioactive multitracer technique. At the same time, chloroplast contents of different concentrations of La3+ treatment were calculated. It was observed that chloroplast contents peaked at 0.02 mM La3+ treatment and that the uptake and distribution of these trace elements in chloroplasts of cucumber seedling leaves are different under different La3+, treatments. With the increase of lanthanum concentrations from 0.002 to 2 mM, the uptake percentages of Se-75, Co-56, and Rb-83 presented an obvious increase and then sharply decreased in contrast to the nonlanthanum treatment, whereas there appeared a sharp decrease and then restored control level in the uptake of V-48. The other two trace elements, namely Tc-95m and Ga-67, were accumulated only in the presence of 0.02 mM La3+. The results indicate that lanthanum treatments to growing the cucumber lead to the change of trace element uptake in the chloroplasts of leaves, which suggest that lanthanum might influence the accumulation of trace elements in chloroplasts of cucumber seedling leaves by regulation of various ion transport mechanisms, thus affecting the photosystem of leaves.

鄂尔多斯盆地上古生界低渗透砂岩有效储层识别与预测

Sulige Gasfield, with a basically proven reserve as high as one trillion cubic meters, is one giant gas field discovered in China. The major gas -bearing layers are Upper Paleozoic strata with fluvial-lacustrine sedimentary facies. Generally, gas reservoirs in this field are characteristic by "five low" properties, namely low porosity, low permeability, low formation pressure, low productivity and low gas abundance. Reservoirs in this field also feature in a large distribution area, thin single sandbody thickness, poor reservoir physical properties, thin effective reservoir thickness, sharp horizontal and/or vertical changes in reservoir properties as well as poor connectivity between different reservoirs. Although outstanding achievements have been acquired in this field, there are still several problems in the evaluation and development of the reservoirs, such as: the relation between seismic attributes and reservoir property parameters is not exclusive, which yields more than one solution in using seismic attributes to predict reservoir parameters; the wave impedance distribution ranges of sandstone and mudstone are overlapped, means it is impossible to distinguish them through the application of post-stack impedance inversion; studies on seismic petrophysics, reservoir geophysical properties, wave reflection models and AVO features have a poor foundation, makes it difficult to recognize the specific differences between tight sandstone and gas-bearing sandstone and their distribution laws. These are the main reasons causing the low well drilling success rate and poor economic returns, which usually result in ineffective development and utilization of the field. Therefore, it is of great importance to perform studies on identification and prediction of effective reservoirs in low permeable sandstone strata. Taking the 2D and 3D multiwave-multicomponent seismic exploration block in Su6-Su5 area of Sulige field as a study area and He 8 member as target bed, analysis of the target bed sedimentary characteristics and logging data properties are performed, while criteria to identify effective reservoirs are determined. Then, techniques and technologies such as pre-stack seismic information (AVO, elastic impedance, wave-let absorption attenuation) and Gamma inversion, reservoir litological and geophysical properties prediction are used to increase the precision in identifying and predicting effective reservoirs; while P-wave and S-wave impedance, ratio of P/S wave velocities, rock elastic parameters and elastic impedance are used to perform sandstone gas-bearing property identification and gas reservoir thickness prediction. Innovative achievements are summarized as follows: 1. The study of this thesis is the first time that multiwave-multicomponent seismic data are used to identify and predict non-marine classic reservoirs in China. Through the application of multiwave-multicomponents seismic data and integration of both pre-stack and post-stack seismic data, a set of workflows and methods to perform high-precision prediction of effective reservoirs in low permeable sandstone is established systematically. 2. Four key techniques to perform effective reservoir prediction including AVO analysis, pre-stack elastic wave impedance inversion, elastic parameters inversion, and absorption attenuation analysis are developed, utilizing pre-stack seismic data to the utmost and increasing the correct rate for effective reservoir prediction to 83% from the former 67% with routine methods. 3. This thesis summarizes techniques and technologies used in the identification reservoir gas-bearing properties using multiwave-multicomponent seismic data. And for the first time, quantitative analysis on reservoir fluids such as oil, gas, and/or water are carried out, and characteristic lithology prediction techniques through the integration of pre-stack and post-stack seismic prediction techniques, common seismic inversion and rock elastic parameters inversion, as well as P-wave inversion and converted wave inversion is put forward, further increasing the correct rate of effective reservoir prediction in this area to 90%. 4. Ten seismic attribute parameters are selected in the 3D multi-wave area to perform a comprehensive evaluation on effective reservoirs using weighted-factor method. The results show that the first class effective reservoir covers an area of 10.08% of the study area, while the second and the third class reservoirs take 43.8% and 46% respectively, sharply increasing the success rate for appraisal and development wells.

中-新元古代海洋的硫和碳同位素的演化

Data on seawater carbon isotope in the Mesoproterozoic and Neoproterozoic is abundant. However, the sulfur isotopic age curve of seawater sulfates determined through the analysis of sulfur isotopic composition of marine evaporite is uncertain in the Mesoproterozoic and Neoproterozoic since evaporites are generally rare in Precambrian. The Mesoproterozoic and Neoproterozoic Carbonate Formations preserve not only the carbon isotopic records, but also the sulfur isotopic records of coeval seawater in the Huabei Platform and the Yangtze Platform, China. Sulfur isotopic composition can be determined by the extraction of trace sulfate from carbonate samples. Successive measurements of sulfur and carbon isotopic compositions of carbonate samples from the Mesoproterozoic and Neoproterozoic strata in the Huabei Platform and the Yangtze Platform was accomplished through the extracting of trace sulfate from carbonates. Sulfur and carbon isotopic compositions of coeval seawater were obtained from analytical results of sulfur and carbon isotopes of the same sample without diagenetic alteration. The high-resolution age curve of sulfur isotope given in this paper may reflect the trend of variations in sulfur isotope composition of seawater sulfates during the Mesoproterozoic and Neoproterozoic. It can be correlated with the characteristics of variation in age curve of carbon isotope of coeval seawater carbonates. The δ34S values of seawater varied from +10.3-37.0‰ during the Mesoproterozoic, which took on oscillated variation on the whole. The δ34S values took on high values in the Mesoproterozoic Chuanlinggou stage, Tuanshanzi stage Tieling stage and in Neoproterozoic Jing'eryu stage. The average of those was about +30‰. The sulfates have low δ34S values in the Mesoproterozoic Yangzhuang stage and Hongshuizhuang stage, The average of those was all lower than +20‰. There occured large-amplitude changs in δ34S values of seawater during the Mesoproterozoic. Large-amplitude oscillate of 534S values occured in the intervals of 1600~1400Ma and 1300~1200Ma. The δ13C values of seawater are mostly negative in Changcheng stage of late Paleoproterozoic, -0 ± 1‰ range in Jixian stage of Mesoproterozoic , and the positive 2±2‰ commonly in early Neoproterozoic Jing'eryu stage. From 1000 Ma to 900 Ma, about 108 years interval of oceanic 513C record is shortage. At the end of Paleoproterozoic (1700 - 1600 Ma), the oceanic 813C values change from -3‰ to 0‰, but strongly oscillate near 1600 Ma. Two larger variations of seawater 513C values occur in the Mesoproterozoic: one is a cycle of about 4%o happens at ca. 1400 Ma; another is rise from >2‰ to>5‰ at ca. 1250 Ma and then become stable at the near 1000 Ma. There appears a large positive excursion over +20‰ in 534S value of ancient seawater sulfates in the early Doushantuo stage. Simultaneously, 8 C values of ancient seawater occur a positive excursion reaching 10‰. These allow δ4S values and 513C values to reach high values of+51.7‰ and +6.9‰, respectively. The range of variation in 834S values of seawater is relatively narrow and 513C values are quite high in the middle Doushantuo stage. Then, δ34S values of seawater become oscillating, the same happens in δ13C values. Negative excursions in 834S values and 813C values occur simultaneously at the end of the Doushantuo stage, and the minimum of δ34S values and δ13C values dropped to -11.3‰ and -5.7‰, respectively. The ancient seawater in the Dengying stage has high δS values and δ13C values. Most of the δ34S values of the trace sulfate samples varied between +23.6‰ and +37.9‰ except two boundaries of the Dengying Formation, and the S13C values of the carbonate samples of the Dengying Formation varied between +0.5‰ and +5.0‰. There appeared large negative excursion in 834S values and δ13C values of ancient seawater at the bounder of Precambrian-Cambrian. The isotopic characteristics of sulfur and carbon implicated that the organic productivity and isotopic fractionation caused by biology were low and the palaeoceanic environment was quite unstable during the Mesoproterozoic. The increase and subsequent oscillation of seawater δ13C value occurred from 1700 to 1600 Ma and near 1300 Ma may be responsible to the two global tectonic events happened at coeval time. The characteristics of variation in sulfur and carbon isotopes of ancient seawater imply strong changes in oceanic environment, which became beneficial to inhabitation and propagation of organism. The organic production and the burial rate of organic carbon once reached a quite high level during the Doushantuo stage. However, the state of environment became unstable that means the global climate and the environment possibly were fluctuating and reiterating after the global glaciation. The negative excursions of S34S values and δ13C values occurring at the end of the Doushantuo stage represent a global event, which might be relative to the oxidation of deep seawater. The isotopic characteristics of sulfur and carbon implicated that there were a high organic productivity and a high burial rate of organic carbon in the Dengying stage. It is obvious that the palaeoceanic environment in Dengying stage was stable corresponding and beneficial for biology to inhabit and propagate except for the two boundaries. The tendency of sulfur and carbon isotopic variations maybe resulted from the gradual oxygenation of ocean environment during the Dengying stage. It has been reported that the secular variations of the sulfur isotopic compositions in seawater was negative correlated with that of carbon isotopic compositions. However, our results show that it is not the case. They were negatively correlated in some intervals and positively in some other intervals of the Mesoproterozoic and Neoproterozoic. The difference in correlation may be associated with the changes in conditions of redox in oceanic environment, e.g. sharp change of the oxidation-reduction interface. The strong changes in global environment may induce the abnormality to occur in the biogeo chemical S and C cycles in the ocean and accordingly sharp Variations in isotopic composition of seawater sulfur and carbon during the Mesoproterozoic and Neoproterozoic. Simultaneously, the global tectonism caused large changes of 87Sr/86Sr ratios. The leading factor that causes the variation in isotopic composition is different in the different intervals of the Mesoproterozoic and Neoproterozoic. Thus, there may exist different models of the biogeochemical S and C cycles in the ocean during the Mesoproterozoic and Neoproterozoic.