Microstructural evolution and formation of nanocrystalline intermetallic compound during surface mechanical attrition treatment of cobalt

Nanocrystalline intermetallic Co3Fe7 was produced on the surface of cobalt via surface mechanical attrition (SMA). Deformationinduced diffusion entailed the formation of a series of solid solutions. Phase transitions occurred depending on the atomic fraction of Fe in the surface solid solutions: from hexagonal close-packed (<4% Fe) to face-centered cubic (fcc) (4-11% Fe), and from fcc to body-centered cubic (>11% Fe). Nanoscale compositional probing suggested significantly higher Fe contents at grain boundaries and triple junctions than grain interiors. Short-circuit diffusion along grain boundaries and triple junctions dominate in the nanocrystalline intermetallic compound. Stacking faults contribute significantly to diffusion. Diffusion enhancement due to high-rate deformation in SMA was analyzed by regarding dislocations as solute-pumping channels, and the creation of excess vacancies. Non-equilibrium, atomic level alloying can then be ascribed to deformation-induced intermixing of constituent species. The formation mechanism of nanocrystalline intermetallic grains on the SMA surface can be thought of as a consequence of numerous nucleation events and limited growth. (C) 2007 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

A study of the mechanism of consolidating metal-powder under explosive-implosive shock-waves

A study of the two-dimensional flow pattern of particles in consolidation process under explosive-implosive shock waves has been performed to further understand the mechanism of shock-wave consolidation of metal powder, in which bunched low-carbon steel wires were used instead of powder. Pressure in the compact ranges from 6 to 30 GPa. Some wires were electroplated with brass, some pickled. By this means, the flow pattern at particle surfaces was observed. The interparticle bonding and microstructure have been investigated systematically for the consolidated specimens by means of optical and electron microscopy, as well as by microhardness. The experimental results presented here are qualitatively consistent with Williamson's numerical simulation result when particle arrangement is close packed, but yield more extensive information. The effect of surface condition of particle on consolidation quality was also studied in order to explore ways of increasing the strength of the compacts. Based on these experiments, a physical model for metal powder shock consolidation has been established.

Nanocrystalline Formation during Mechanical Attrition of Cobalt

The nanocrystalline (nc) formation was studied in cobalt (a mixture of c (hexagonal close packed) and gamma (face-centered cubic) phases) subjected to surface mechanical attrition treatment. Electron microscopy revealed the operation of {10(1) over bar 0}< 11(2) over bar 0 > prismatic and {0001}< 11(2) over bar 0 > basal slip in the E phase, leading to the successive subdivision of grains to nanoscale. In particular, the dislocation splitting into the stacking faults was observed to occur in ultrafine and nc grains. By contrast, the planar dislocation arrays, twins and martensites were evidenced in the gamma phase. The strain-induced gamma ->epsilon martensitic transformation was found to progress continuously in ultrafine and nc grains as the strain increased. The nc formation in the gamma phase was interpreted in terms of the martensitic transformation and twinning.

A uniform 290 nm periodic square structure on ZnO fabricated by two-beam femtosecond laser ablation

A uniform submicron periodic square structure was fabricated on the surface of ZnO by a technique of two linearly polarized femtosecond laser beams with orthogonal polarizations ablating material alternately. The formed two-dimensional ordering submicron structure consists of close-packed submicron squares with a spacial periodicity of 290 nm, which arises from the intercrossing of two orthogonal submicron ripple structures induced by the two beams respectively. The result demonstrates a noninterference effect of two-beam ablation based on the alternate technique, which should come from the polarization-dependent enhancement of the subwavelength ripple structure and the large interval of two alternate pulses. This two-beam alternate ablation technique is expected to open up prospects for the submicron fabrication of wide-bandgap materials.

Subwavelength imaging by a dielectric-tube photonic crystal

In contrast to previous two-dimensional coated photonic crystals, in this paper we propose a left-handed one that is made of dielectric tubes arranged in a close-packed hexagonal lattice. Without metallic cores, this structure is low-loss and convenient to fabricate. Negative refraction and its resulting focusing are investigated by dispersion characteristic analysis and numerical simulation of the field pattern. With proper modification at the interface, the image is improved. With better isotropy than that with noncircular rods, planoconcave lenses made by dielectric tubes focus a Gaussian beam exactly at R//n - 1/.

Bibarba bibarba: A new genus and species of Cobitinae (Pisces : Cypriniformes : Cobitidae) from Guangxi Province (China)

A new genus of Cobitinae, Bibarba gen. n., and a new species, B. bibarba sp. n., were discovered and are described for the Chengjiang River, a tributary of the Hongshuihe River in Guangxi Province of southern China. This river region is characterized by a Karst landscape, and the river that is inhabited by the new genus is a slowly moving stream with arenaceous and cobblestone beds. The new genus resembles Cobitis Linnaeus, 1758 (subfamily Cobitinae) in the shape and pigmentation pattern of their body, the absence of scales on their head, and the presence of a suborbital spine, but differs from it by a single Lamina circularis on the third pectoral fin ray instead of on the base of the second pectoral fin ray; two pairs of barbels (one rostral pair and one maxillo-mandibular pair) instead of three pairs of barbels (one rostral pair, one maxillary pair, and one maxillo-mandibular pair); a relatively thick and short suborbital spine with a strong medio-lateral process instead of a suborbital spine without or with a weakly formed medio-lateral process as in Cobitis; and the lack of a black stripe extending from the occiput through the eye to the insertion of the rostral barbel. The first two characters have not been reported in any other genus of the subfamily Cobitinae. A morphometric character analysis based on PCA reveals differences between B. bibarba and C. sinensis in body size, barbel length, interorbital width, pectoral fin length in males, and the position of the dorsal and ventral fins. Type specimens of the new species are kept in the Freshwater Fishes Museum of the Institute of Hydrobiology at the Chinese Academy of Sciences in Wuhan, Hubei Province. (c) 2007 Elsevier GmbH. All rights reserved.

Histological and cytological studies on the developing thymus of mandarin fish Siniperca chuatsi (Perciformes : Teleostei)

The thymus of the mandarin fish, Siniperca chuatsi, was examined by light and transmission electron microscopy to understand its formation and cellular composition. Larvae of the mandarin fish were collected and sectioned from 1 to 35 days post-hatching (dph). On dph 7 the thymus was packed with lymphocytes. From 12 dph onward, mucous cells were observed on the epithelial layer; from 23 dph, three zones could be differentiated in the thymic parenchyma. The thymus was connected with the extension of the third, fourth and fifth branchial pouches throughout early development, remaining in a superficial position in the adult S. chuatsi. In the thymus of the adult fish, thymic epithelial cells (TECs) characteristic of tonofilaments were observed, with limiting TECs (LECs) found in subcapsular, subseptal, perivascular and nurse-like TECs containing viable intact lymphocytes inside their vacuoles. In addition, three kinds of granulocytes were observed throughout the thymus, and an incomplete blood-thymus barrier was found in the inner zone. Other cell components such as cystic cells, macrophages and plasma cells, were also described in the thymus of the adult S. chuatsi. The thymus development in mandarin fish agrees, to some extent, with the ontogenetic patterns observed in other fish species.

Distribution, feeding and body condition of four small fish species in the near-shore and central areas of Liangzi Lake, China

Small fish abundance is usually high in heavily vegetated habitats in Yangtze lakes, China. Visual and swimming barriers created by dense macrophytes beds could reduce feeding efficiency and growth of small fishes. We tested the hypothesis that small fishes in habitats with dense macrophytes would show decreased feeding efficiency and reduced growth rates by comparing feeding efficiency (measured as the relative weight of fore-gut contents), total length, and condition factor of four small young-of-the-year fishes collected in the near-shore (heavily vegetated) and central (less vegetated) areas of Liangzi Lake. Feeding efficiency, total length, or condition factor were each significantly reduced in the near-shore area compared with the central area for Ctenogobius giurinus, Pseudorasbora parva and Carassius auratus auratus. This supports our hypothesis that vegetation abundance may mediate feeding efficiency and growth of small fishes. Although Hypseleotris swinhonis did not show significant decreases in feeding efficiency or growth in the near-shore area, there was not any reversed tendency, i.e. increased feeding rate or growth in the near-shore area compared to the central area.

Long-term toxic impact of 2,3,7,8-tetrachlorodibenzo-p-dioxin on the reproduction, sexual differentiation, and development of different life stages of Gobiocypris rarus and Daphnia magna

The sexual ratio of Gobiocypris rarus exposed to 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) and 17 beta -estradiol from embryo to sexually mature revealed feminization and overdevelopment of connective tissue in male fish gonad in 2-30 pg/L TCDD concentration range. Daphnia magna was not sensitive to the high dose of TCDD (0.1-1000 ng/ml), but the reproduction of D. magna treated with TCDD decreased after the 8th day. 7-Ethoxyresorufin-O-deethylase (EROD) activities in newly fertilized eggs of G. rarus exposed to TCDD dosage groups (1000-100,000 pg/L) were significantly induced and increased with TCDD concentrations at the early life stage, while no difference was found between low TCDD dosage groups (<100 pg/L), but a good relationship between the EROD activity and the TCDD concentration was observed during a long-term developmental stage. There was a pericardial edema formed in a 2-week yolk-sac at the concentration of 1000 pg/L TCDD. But in the exposure group (2 pg/L TCDD for 120 days), the cell nuclei of hepatocytes was far from the center and packed toward the cell membrane; the cristae of most mitochondria in the cell dropped and collapsed; the rough endoplasmic reticulum broke into fragments; and numerous lipid droplets formed in the cell. (C) 2001 Academic Press.

Kinetically controlled InN nucleation on GaN templates by metalorganic chemical vapour deposition

This paper presents a study on the nucleation and initial growth kinetics of InN on GaN, especially their dependence on metalorganic chemical vapour deposition conditions. It is found that the density and size of separated InN nano-scale islands can be adjusted and well controlled by changing the V/III ratio and growth temperature. InN nuclei density increases for several orders of magnitude with decreasing growth temperature between 525 and 375 degrees C. At lower growth temperatures, InN thin films take the form of small and closely packed islands with diameters less than 100 nm, whereas at elevated temperatures the InN islands grow larger and become well separated, approaching an equilibrium hexagonal shape due to enhanced surface diffusion of adatoms. The temperature dependence of InN island density gives two activation energies of InN nucleation behaviour, which is attributed to two different kinetic processes related to In adatom surface diffusion and desorption, respectively.

The influence of growth temperature and input V/III ratio on the initial nucleation and material properties of InN on GaN by MOCVD

The effects of growth temperature and V/III ratio on the InN initial nucleation of islands on the GaN (0 0 0 1) surface were investigated. It is found that InN nuclei density increases with decreasing growth temperature between 375 and 525 degrees C. At lower growth temperatures, InN thin films take the form of small and closely packed islands with diameters of less than 100 nm, whereas at elevated temperatures the InN islands can grow larger and well separated, approaching an equilibrium hexagonal shape due to enhanced surface diffusion of adatoms. At a given growth temperature of 500 degrees C, a controllable density and size of separated InN islands can be achieved by adjusting the V/III ratio. The larger islands lead to fewer defects when they are coalesced. Comparatively, the electrical properties of the films grown under higher V/III ratio are improved.

Efficiently producing single-walled carbon nanotube rings and investigation of their field emission properties

Single-walled carbon nanotube (SWNT) rings with a diameter of about 100 nm have been prepared by thermally decomposing hydrocarbon in a floating catalyst system. These rings appeared to consist mostly of SWNT toroids. High resolution transmission electron microscopy showed that these rings were composed of tens of SWNTs with a tightly packed arrangement. The production of SWNT rings was improved through optimizing various growth parameters, such as growth temperature, sublimation temperature of the catalyst, different gas flows and different catalyst components. The growth mechanism of the SWNT rings is discussed. In the field emission measurements we found that field emission from a halved ring is better than that from a whole SWNT ring, which contributed to the better emission from two opened ends of the nanotubes of the halved SWNT ring.

Structural characteristic of cubic GaN nucleation layers on GaAs(001) substrates by MOCVD

The structural characteristic of cubic GaN (C-GaN) nucleation layers on GaAs(0 0 1) substrates by metalorganic chemical vapor deposition was in detail investigated first by X-ray diffraction (XRD) measurements, using a Huber five-circle diffractometer and an intense synchrotron X-ray source. The XRD results indicate that the C-GaN nucleation layers are highly crystallized. Phi scans and pole figures of the (1 1 1) reflections give a convincing proof that the GaN nucleation layers show exactly cubic symmetrical structure. The GaN(1 1 1) reflections at 54.74degrees in chi are a measurable component, however (002) components parallel to the substrate surface are not detected. Possible explanations are suggested. The pole figures of {1 0 (1) over bar 0} reflections from H-GaN inclusions show that the parasitic H-GaN originates from the C-GaN nucleation layers. The coherence lengths along the close-packed [1 1 1] directions estimated from the (1 1 1) peaks are nanometer order of magnitude. (C) 2002 Elsevier Science B.V. All rights reserved.

One-pot synthesis and self-assembly of colloidal copper(I) sulfide nanocrystals

A simple one-pot method is developed to prepare size-and shape-controlled copper(I) sulfide (Cu2S) nanocrystals by thermolysis of a mixed solution of copper acetylacetonate, dodecanethiol and oleylamine at a relatively high temperature. The crystal structure, chemical composition and morphology of the as-obtained products are characterized by powder x-ray diffraction (PXRD), x-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES), transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The morphology and size of the Cu2S nanocrystals can be easily controlled by adjusting the reaction parameters. The Cu2S nanocrystals evolve from spherical to disk-like with increasing reaction temperature. The spherical Cu2S nanocrystals have a high tendency to self-assemble into close-packed superlattice structures. The shape of the Cu2S nanodisks changes from cylinder to hexagonal prism with prolonged reaction time, accompanied by the diameter and thickness increasing. More interestingly, the nanodisks are inclined to self-assemble into face-to-face stacking chains with different lengths and orientations. This one-pot approach may extend to synthesis of other metal sulfide nanocrystals with different shapes and sizes.