ENHANCED AMPEROMETRIC DETECTOR FOR LOCAL-ANESTHETICS IN LIQUID-CHROMATOGRAPHY WITH METAL-OXIDE DISPERSED GLASSY-CARBON ELECTRODES

Chemically modified electrodes (CMEs) prepared by the dispersion of metal oxide particles on a glassy carbon (GC) substrate greatly enhance the voltammetric response and amperometric detection of local anesthetics following liquid chromatography (LC). The enhancement is more pronounced with the GC electrodes dispersed by the metal oxides of higher oxidation states (+3, +4) and for the species exhibiting relatively slow electrode kinetics under given conditions. With an applied potential of 1.2 V (vs. SCE), LC amperometric detection of the analytes at the alpha-alumina modified GC surface gives detection limits 2-5 times lower than those obtained at the bare electrode. The metal oxide-dispersed electrodes display significant improvement in sensitivity, and selectivity and indicate excellent preparation reproducibility and performance stability.

Heterogeneous enantioselective epoxidation catalyzed by Mn(salen) complexes grafted onto mesoporous materials by phenoxy group

Three chiral Mn(salen) complexes were immobilized into different mesoporous material via phenoxy group by a simplified method and they show high activity and enantioselectivity for asymmetric epoxidation of various substituted unfunctional olefins. The heterogeneous Mn(salen) catalysts show comparable ee values for asymmetric epoxidation of styrene and 6-cyano-2,2-dimethylchromene and much higher ee values for epoxidation of a-methylstyrene (heterogeneous 79.7% ee versus homogeneous 26.4% ee) and cis-beta-methylstyrene (heterogeneous 94.9% ee versus homogeneous 25.3% ee for cis-epoxide) than the homogeneous catalysts. These heterogeneous catalysts also remarkably alter the cis/trans ratio of epoxides for asymmetric epoxidation of cis-beta-methylstyrene (heterogeneous 21 versus homogeneous 0.38). The axial tether group does not make a big effect on ee values and the increase in ee value and change in cis/trans ratio are mainly attributed to the axial immobilization mode and the support effect of heterogeneous catalysts. The catalysts keep constant ee values for the recycle tests of eight times for asymmetric epoxidation of a-methylstyrene. And several possibilities were proposed to elucidate the difference in ee values of heterogeneous catalysts from homogeneous catalysts. (c) 2005 Elsevier B.V. All rights reserved.

不同玻璃组分对掺铒碲酸盐玻璃 光谱性质的影响

Series of tellurite glasses were prepared by traditional melting method, the glass composition were changed and the different effects of glass modifier oxides(alkali metals and alkaline earth metal oxides) and glass intermediate (Y2O3, GeO2, Nb2O5, WO3) on the optical and spectroscopic properties of Er³⁺ doped tellurite glass were researched and compared. The infrared transmitting spectra, absorption spectra and fluorescence spectra were tested, the results showed that Nb2O5 and WO3 in the glass act as part of the body's role in the formation of the network, caused the reduction of transmitting range in infrared wavelength, which decrease the transmitting properties of tellurite glass. The introduction of high valence cationic ions, WO3 especially, can increase the FWHM of Er³⁺ for the increased polarization effect. With the decreasing of cationic field of glass modifier ions, the ion filed of the environment around Er³⁺ increased, subsequently, the role of ligand field polarization effect reduced, which makes the luminescence lifetime increase, and on the contrary the FWHM decrease monotonously.

Phosphorus in suspended matter and sediments of a hypertrophic lake. A case study: Lake Dianchi, China

From June 2004 to December 2004, Lake Dianchi, which had large scale of cyanobacterial blooms was investigated in order to study P-fractionation in the suspended matter and the sediment. The investigation improves our understanding of phosphorus in Lake Dianchi and the relationship between phosphorus and cyanobacterial blooms. It contributes to the available literature on the behavior of P in hypertrophic lakes. The distribution of P-fractions in Lake Dianchi was not uniform from northwest to south, but was closely related to the trophic status of the whole lake. The concentrations of total phosphorus, labile P (NH4Cl-P), Organic P (NaOH-NRP) and loss on ignition in suspended matter were positively correlated with the strength of cyanobacterial blooms. Total phosphorus in suspended matter was relatively stable for almost half an year and closely related to Chl. a concentration. The main content of organic phosphorus is in the cyanobacterial blooms. The concentrations of phosphorus bound to metal oxides and carbonates (NaOH-SRP and HCl-P) in sediment were similar to NaOH-SRP and HCl-P in the corresponding suspended matter. The latter two forms of P in suspended matter were not affected by cyanobacterial blooms, indicating that the inorganic phosphorus is derived from the sediment after resuspension from the sediment due to wind and wave action. The contribution of the different P-fractions to TP in sediment and in suspended matter indicates that NH4Cl-P in the suspended matter is an important buffer for maintaining dissolved phosphorus in water.

几种稀土氟化物和氧化物纳米发光材料的制备、性能及其应用探索研究

目前，纳米材料已经应用于很多医药和生物领域，诸如临床诊断、药物传送、体内体外荧光标记等。稀土离子掺杂的纳米材料因其独特的发光性质已被认为是有前景的生物荧光标记，二氧化硅作为环境友好发光材料也受到越来越多的重视。本论文合成稀土离子掺杂的下转换和上转换发光纳米材料，并进行表面功能化，使之连接生物药物小分子，以期作为荧光标记。同时采用不同方法制备不同大小的二氧化硅球，并研究其发光性质。 采用多醇法成功地制备出结晶程度高的CeF3:Tb3+纳米粒子。氧化硅和胺基硅烷包覆使纳米粒子具有胺基功能化，然后通过SOCl2成功地活化生物素使之连接到纳米粒子上并随之与亲合素键合。胺基功能化的CeF3:Tb3+ 纳米粒子发光产生严重的猝灭，而生物分子与纳米粒子结合后发光得到很大程度上的恢复。生物功能化的CeF3:Tb3+ 纳米粒子能很好地分散在水中，为这些CeF3:Tb3+ 纳米粒子作为生物荧光探针奠定了基础。同时以P123为结构导向剂，介孔氧化硅成功地包覆CeF3:Tb3+ 纳米粒子。介孔氧化硅层存在部分有序的六方介孔体系和部分微孔结构，该复合物保持绿色荧光性质并具有相当大的孔容和大的表面积。布洛芬能载入复合物的孔道中，在24 h内释放完全。因此，这类复合物可以在靶向的药物传送体系中具有潜在的应用价值。 利用多醇法制备出NaYF4:Yb3+, Er3+ 纳米粒子。NaYF4:Yb3+, Er3+ 纳米粒子进行胺基功能化，并通过氧化寡糖链成功地活化亲合素，使之连接到胺基功能化的纳米粒子上。生物功能化的 NaYF4:Yb3+, Er3+纳米粒子仍保持较好的上转换发光性质，可以作为生物体系的荧光探针。另外用 P123作为结构导向剂和助表面活性剂PVP 或 TMB 成功地使NaYF4:Yb3+, Er3+ 纳米粒子包覆介孔氧化硅。外层氧化硅层有介孔结构。该复合物保持红色荧光性质，并具有大的孔容、表面积。布洛芬能载入复合物的孔道中，在12 h内完全释放。 通过高温溶剂法合成出YVO4:Eu3+ 纳米粒子。粒子结晶程度高，为椭球形状，长轴为80 nm，短轴为43 nm。YVO4:Eu3+ 纳米粒子的荧光发射跃迁主要源于5D0能级。FT-IR 谱和 XPS 谱表明纳米粒子表面的配体为油酸和油胺分子。Eu3+ (5D0 level) 寿命因表面有机配体的存在比体材料的寿命短。 成功地制备出不同大小的纳米至亚微米尺度且具有发光性能的单分散二氧化硅球，其尺寸随胺基浓度的增加而增大。烧结后粒子仍保持单分散性，但其尺寸缩小。烧结后的二氧化硅球含有C杂质。亚微米尺度的二氧化硅球的发射带最大值随氨丙基三乙氧基硅烷（APTES）浓度的增加而红移，但是纳米尺度的二氧化硅球的发射带最大值红移更大。单分散二氧化硅球发光原因归于二氧化硅结构中存在的碳和氧缺陷。

The role of molybdenum oxide as anode interfacial modification in the improvement of efficiency and stability in organic light-emitting diodes

It has been experimentally found that molybdenum oxide (MoO3) as the interfacial modification layer on indium-tin-oxide (ITO) in organic light-emitting diodes (OLEDs) significantly improves the efficiency and lifetime. In this paper, the role of MoO3 and MoO3 doped N,N '-di(naphthalene-1-yl)-N,N '-diphenyl-benzidine (NPB) as the interface modification layer on ITO in improvement of the efficiency and stability of OLEDs is investigated in detail by atomic force microscopy (AFM), polarized optical microscopy, transmission spectra, ultraviolet photoemission spectroscopy (UPS) and X-ray photoemission spectroscopy (XPS).

Tungsten oxide doped N,N-'-di(naphthalen-1-yl)-N,N-'-diphenyl-benzidine as hole injection layer for high performance organic light-emitting diodes

By introducing tungsten oxide (WO3) doped N,N-'-di(naphthalen-1-yl)-N,N-'-diphenyl-benzidine (NPB) hole injection layer, the great improvement in device efficiency and the organic film morphology stability at high temperature were realized for organic light-emitting diodes (OLEDs). The detailed investigations on the improvement mechanism by optical, electric, and film morphology properties were presented. The experimental results clearly demonstrated that using WO3 doped NPB as the hole injection layer in OLEDs not only reduced the hole injection barrier and enhanced the transport property, leading to low operational voltage and high efficiency, but also improved organic film morphology stability, which should be related to the device stability. It could be seen that due to the utilization of WO3 doped NPB hole injection layer in NPB/tris (8-quinolinolato) aluminum (Alq(3))-based device, the maximum efficiency reached 6.1 cd A(-1) and 4.8 lm W-1, which were much higher than 4.5 cd A(-1) and 1.1 lm W-1 of NPB/Alq(3) device without hole injection layer. The device with WO3 doped NPB hole injection layer yet gave high efficiency of 6.1 cd A(-1) (2.9 lm W-1) even though the device was fabricated at substrate temperature of 80 degrees C.

Oxidation of cyclohexane - A significant impact of stainless steel reactor wall

The selective oxidation of cyclohexane to cyclohexanol and cyclohexanone is an important chemical process and it has been paid more attentions recently. In the present work, the stainless steel reactor wall was found to influence the selective oxidation of cyclohexane very significantly, and a quasi-crystalline Ti45Zr35Ni17Cu3 alloy with the similar compositions as the reactor wall was used as a catalyst for the cyclohexane oxidation, as expected, a higher activity was obtained with it. The present results open up a new avenue for developing new catalyst for alkane oxidation.

Tunable synthesis, growth mechanism, and magnetic properties of La0.5Ba0.5MnO3

La0.5Ba0.5MnO3 products with novel flowerlike, microcube, and nanocube structures were successfully synthesized by a simple hydrothermal route by controlling the alkalinity of the reaction solutions. The synthesized products were systematically studied by X-ray powder diffraction, field-emission scanning electron microscopy, transmission electron microscopy, and energy dispersive X-ray spectroscopy. The results showed that the formation of the flowerlike structures with a layer assembly experienced a nucleation-aggregation-crystallization growth process, while the cubic structures experienced a nucleation-crystallization growth process due to the effect of different alkalinity in the reaction solutions. The higher alkalinity also led to a decrease in the size in the cubic structures. Suitable temperature and pressure were demonstrated to be crucial to the formation of the flowerlike structures by carrying out further control experiments. The measurement of the magnetic properties of three samples obtained at different alkaline conditions indicated that the size of the La0.5Ba0.5MnO3 products had an obvious influence on their properties; however, the dependence of the properties upon the morphology of the La0.5Ba0.5MnO3 products was minor.

One-step synthesis and characterization of polyelectrolyte-protected gold nanoparticles through a thermal process

Polyelectrolyte-protected gold nanoparticles have been facilely obtained by heating an amine-containing polyelectrolyte/HAuCl4 aqueous solution without the additional step of introducing other reducing agents. All experimental data indicate that different initial molar ratio of polyelectrolyte to gold can lead to the formation of dispersed nanoparticles, quasi one-dimensional aggregates of nanoparticles or bulk metal deposits. More importantly, the growth kinetics of gold particles thus formed can be tuned by changing the initial molar ratio of polyelectrolyte to gold.

Effects R3+ on the photoluminescent properties of Ca2R8(SiO4)(6)O-2 : A (R = Y, La, Gd; A= Eu3+, Tb3+) phosphor films prepared by the sol-gel process

Using CaCO3, metal oxides (all dissolved by nitric acid) and tetraethoxysilane Si(OC2H5)(4) (TEOS) as the main starting materials, Ca2R8(SiO4)(6)O-2:A (R = Y, La, Gd; A = EU3+, Tb3+) phosphor films have been dip-coated on quartz glass substrates through the sol-gel process. X-ray diffraction (XRD), atomic force microscope (AFM), scanning electron microscope (SEM) and photoluminescence (PL) spectra as well as lifetimes were used to characterize the resulting films. The results of XRD indicated that the 1000 degreesC annealed films are isomorphous and crystallize with the silicate oxyapatite structure. AFM and SEM studies revealed that the phosphor films consisted of homogeneous particles ranging from 30 to 90 nm, with an average thickness of 1.30 mum. The Eu3+ and Tb3+ show similar spectral properties independent of R 3, in the films due to their isomorphous crystal structures. However, both the emission intensity and lifetimes of Eu3+ and Tb3+ in Ca2R8(SiO4)(6)O-2 (R = Y, La, Gd) films decrease in the sequence of R = Gd > R = Y > R = La, which have been explained in accordance with the crystal structures.

Bronsted guanidine acid-base ionic liquids: Novel reaction media for the palladium-catalyzed Heck reaction

Bronsted acid-base ionic liquids (GILs) based on guanidine and acetic acid are efficient reaction media for palladium-catalyzed Heck reactions. They offer the advantages of high activity and reusability. GIL2 plays multiple roles in the reaction: it could act as solvent, as a strong base to facilitate beta-hydride elimination, and as a ligand to stabilize activated Pd species.

Magnetic and electric properties of Bi(La)Sr(Ca)Mn2O6

Bi1-xLaxSrMn2O6 and BiSr1-xCaxMn2O6 are prepared by solid state reaction. They are n-type semiconductors with ferromagnetism at room temperture. When Bi is substituted partly by rare earth, a negative magnetoresistance effect is observed in the pellet of Bi1-xLaxSrMn2O6. There are semiconductor-metal transitions at 820 K in BiSrMn2O6. The transitions are attributed to the magnetic transition at high temperature. The substitution of Ca for Sr makes the transition temperature increase. However, when Bi is partly substituted by La, the solid solution does not change into metal. (C) 1996 Academic Press, Inc.

SYNTHESIS OF A NEW TYPE OF CH3CN-COORDINATED LANTHANIDE COMPOUNDS LN(CH3CN)9(ALCL4)3CH3CN

Acetonitrile is a weakly donating ligand. The cationic compounds of CH_3CN-coordinated transition metal are versatile homogeneous catalysts for the polymerization and isomerization of olefins and cycloolefins. The cationic compound of lanthanide[Eu(CH_3·CN)_3(BF_4)_3]_n was prepared from the oxidation of Eu with NOBF_4 in CH_3CN by Thomas in 1986. It was found that [Eu(CH_3CN)_3(BF_4)_3]_n can catalyze the polymerization of styrene cyclohexadiene and other olefins. However, there is no information about...

Characteristics of sulfide corrosion products on 316L stainless steel surfaces in the presence of sulfate-reducing bacteria

It has been found that microbial communities play a significant role in the corrosion process of steels exposed in aquatic and soil environments. Biomineralization influenced by microorganisms is believed to be responsible for the formation of corrosion products via complicated pathways of electron transfer between microbial cells and the metal. In this study, sulfide corrosion products were investigated for 316L stainless steel exposed to media with sulfate-reducing bacteria media for 7 weeks. The species of inorganic and organic sulfides in the passive film on the stainless steel were observed by epifluorescence microscope, environmental scanning electron microscope combined with energy dispersive spectroscopy and X-ray photoelectron spectroscopy. The transformation from metal oxides to metal sulfides influenced by sulfate-reducing bacteria is emphasized in this paper. (c) 2005 Elsevier B.V. All rights reserved.