The influence of thickness on properties of GaN buffer layer and heavily Si-doped GaN grown by metalorganic vapor-phase epitaxy

The physical properties of low-temperature-deposited GaN buffer layers with different thicknesses grown by metal-organic vapor-phase epitaxy have been studied. A tentative model for the optimum thickness of buffer layer has been proposed. Heavily Si-doped GaN layers have been grown using silane as the dopant. The electron concentration of Si-doped GaN reached 1.7 x 10(20) cm(-3) with mobility 30 cm(2)/V s at room temperature. (C) 1998 Published by Elsevier Science B.V. All rights reserved.

Electronic investigation of self-organized InAs quantum dots

Deep Level Transient Spectroscopy (DLTS) has been applied to investigate the electronic properties of self-organized InAs quantum dots. The energies of electronic ground states of 2.5ML and 1.7ML InAs quantum dots (QDs) with respect to the conduction band of bulk GaAs are about 0.21 eV and 0.09 eV, respectively. We have found that QDs capture electrons by lattice relaxation through a multi-phonon emission process. The samples are QDs embedded in superlattices with or without a 500 Angstrom GaAs spacing layer between every ten periods of a couple of GaAs and InAs layers. The result shows that the density of dislocations in the samples with spacer layers is much lower than in the samples without the spacer layers.

Material transport in self-assembled InAs/GaAs quantum dot ensemble

Introducing the growth interruption between the InAs deposition and subsequent GaAs growth in self-assembled quantum dot (QD) structures, the material transport process in the InAs layers has been investigated by photoluminescence and transmission electron microscopy measurement. InAs material in structures without misfit dislocations transfers from the wetting layer to QDs corresponding to the red-shift of PL peak energy due to interruption. On the other hand, the PL peak shifts to higher energy in the structures with dislocations. In this case, the misfit dislocations would capture the InAs material from the surrounding wetting layer and coherent islands leading to the reduction of the size of these QDs. The variations in the PL intensity and Linewidth are also discussed.

Influence of interdot electronic coupling on photoluminescence spectra of self-assembled InAs/GaAs quantum dots

The influence of interdot electronic coupling on photoluminescence (PL) spectra of self-assembled InAs/GaAs quantum dots (QDs) has been systematically investigated combining with the measurement of transmission electron microscopy. The experimentally observed fast red-shift of PL energy and an anomalous reduction of the linewidth with increasing temperature indicate that the QD ensemble can be regarded as a coupled system. The study of multilayer vertically coupled QD structures shows that a red-shift of PL peak energy and a reduction of PL linewidth are expected as the number of QD layers is increased. On the other hand, two layer QDs with different sizes have been grown according to the mechanism of a vertically correlated arrangement. However, only one PL peak related to the large QD ensemble has been observed due to the strong coupling in InAs pairs. A new possible mechanism to reduce the PL linewidth of QD ensemble is also discussed.

The enhancement of diffusion by strain of InAs quantum dots in a GaAs matrix

We investigate the annealing behavior of Photoluminescence (PL) from self-assembled InAs quantum dots (QDs) with different thicknesses GaAs cap layers. The diffusion introduced by annealing treatment results in a blue-shift of the QD PL peak, and a decrease in the integrated intensity. The strain present in QDs enhances the diffusion, and the QDs with the cap layers of different thicknesses will experience a strain of different strength. This can lend to a, better understanding of the larger blue-shift of the PL peak of the deeper buried QDs, and the different variance of the full width at half maximum of the luminescence from QDs with the cap layers of different thicknesses.

Optical anisotropy of InAs submonolayer quantum wells in a (311) GaAs matrix

The steplike density of states obtained from reflectance-difference spectroscopy demonstrates that ultrathin InAs layers should be regarded as two-dimensional quantum wells rather than isolated clusters, even for the sample with only 1/3 monolayer InAs in (311)-oriented GaAs. The degree of anisotropy is within the intrinsic anisotropy of (311)-oriented ultrathin quantum wells, indicating that there is little structural or strain anisotropy in the InAs islands. (C) 1998 Elsevier Science B.V.

The photon scanning tunneling microscope and its applications

A simple photon scanning tunneling microscope (PSTM) is described. Its lateral resolution (similar to 10nm with a maximal scanning range of 10 mu m x 10 mu m ) is much better than that of a conventional optical microscope. Its principle, the fiber optic tip fabrication and PSTM images of different samples such as mica, HDPE and LiNbO3 are presented.

Aluminum induced crystallization of strongly (111) oriented polycrystalline silicon thin film and nucleation analysis

A polycrystalline silicon thin film was fabricated on glass substrate by means of aluminum induced crystallization (AIC). Al and alpha-Si layers were deposited by magnetron sputtering respectively and annealed at 480A degrees C for 1 h to realize layer exchange. The polycrystalline silicon thin film was continuous and strongly (111) oriented. By analyzing the structure variation of the oxidation membrane and lattice mismatch between gamma-Al2O3 and Si, it was concluded that aluminum promoted the formation of (111) oriented silicon nucleus by controlling the orientation of gamma-Al2O3, which was formed at the early stage of annealing.

液滴在超疏水表面上的电场启动以及碰撞的实验研究

液滴操纵和控制是实现微全分析系统(μTAS)和芯片上的实验室(lab-on-a-chip)功能的基础,基于液滴操控的显示及微透镜已经成功应用。目前电润湿启动液滴方法简单、响应时间快,引起越来越多的关注。另一方面超疏水表面上的液滴具有低摩擦、低粘附的特性,借由这种原理制作的微流器件可以实现微量液体传输。为了更好的利用超疏水表面的特性,就需要研究液滴运动规律,以及表面特性的影响。

Pool Boiling on Wire in Microgravity - What Have We Learned

In the past years, steady pool boiling of degassed R113 on thin platinum wires has been studied systematically in our lab, including experiments in long-term microgravity aboard RS-22, in short-term microgravity in the Drop Tower Beijing / NMLC, and in normal gravity on the ground. Slight enhancement of nucleate boiling heat transfer is observed in microgravity, while dramatic changes of bubble behaviors are much evident. The value of CHF in microgravity is lower than that in normal gravity, but it can be predicted well by the Lienhard-Dhir correlation, although the dimensionless radius in the present case is far beyond its initial application range. The scaling of CHF with gravity is thus much different from the traditional viewpoint. Considering the influence of the Marangoni effects, the different characteristics of bubble behaviors in microgravity have been explained. A new bubble departure model has also been proposed, which can predict the whole observation both in microgravity and in normal gravity.

路易斯碱催化的烯胺不对称还原研究

手性胺不仅是许多天然产物和手性药物的重要结构单元，而且也是非常有用的拆分试剂、手性配体和手性催化剂。亚胺和烯胺的不对称催化还原是制备手性胺的最直接有效的方式之一，手性有机小分子催化的亚胺不对称还原已取得了很大的进展，但到目前为止，有机小分子催化的烯胺不对称还原极少见文献报道。 本研究以廉价的三氯氢硅为氢源、DMF 等路易斯碱为催化剂实现了烯胺的高效还原。通过反应条件的优化，各种烯胺底物在0.1 eq. DMF 催化下、12 个小时内可以获得非常高的收率（>93%）。 在本课题组前期研究的基础上，我们筛选并设计了一系列以手性哌啶酸和叔丁基亚磺酰胺为母体的有机小分子路易斯碱催化剂，它们能催化三氯氢硅对(Z)-N-苄氧羰基-1-苯基丙烯胺的不对称还原，获得很高的收率和中等的对映选择性，并且具有很好的底物普适性。另外，通过机理方面的研究，我们推测在反应过程中一分子烯胺先捕获一个质子而转变为亚胺正离子，然后受到路易斯碱活化的三氯氢硅中的富电氢原子进攻该亚胺正离子得到还原产物。 另外，本文列出了在此课题进展中所发现的一些新反应，并且试图去阐释这些反应的作用机理。 Catalytic enantioselective reduction of imines and enamines represents one of the most straightforward and efficient methods for the preparation of chiral amines, which are not only important building blocks of many natrural products and chiral drugs, but also can serve as useful resolution reagents, chiral ligands and chiral catalysts. By now, asymmetric reduction of enamines catalyzed by organocatalysts has scarcely been reported, although organocatalyzed enantioselective reduction of imines has already gained great progress. In this study, we report the DMF-catalyzed reduction of enamines with high yields using HSiCl3 as the reducing agent. Under the optimized reaction conditions, various enamines can be reduced in the presence of 0.1 eq. DMF with high yields (>93%) in 12 hours. We screened a set of Lewis base organocatalysts derived from chiral pipecolinic acid and tert-butanesulfinamide for the reduction of (Z)-N-Cbz-1- phenylpropenamine, including newly designed ones and some of those previously developed in our lab. However, only moderate stereoselectivities, albeit high yields were obtained. As for the mechanism, we speculate that the enamine firstly engages a proton to form an iminium species, which is then attacked by the nucleophlic hydrogen of HSiCl3 activated by Leiws base. During the above studies, we have also discovered some new reactions, for which feasible mechanisms were proposed.

吲哚生物碱Desbromoarborescidine A 的全合成及烯胺C-亚磺酰化反应研究

从新几内亚核桃木的树皮中分离得到的吲哚类喹诺里西定生物碱10-Desbromoarborescidine A，因发现其具有阻滞钙离子通道的活性而倍受关注。10-Desbromoarborescidine A由A、B、C、D四个环组成，只有一个手性中心，是吲哚生物碱中结构较简单的一种，常作为此类生物碱全合成方法的模型化合物。但迄今为止，能高效而简便的实现手性10-Desbromoarborescidine A不对称全合成方法线路不多，大多数以不对称诱导的方式建立其手性中心，手性催化的方式仅有一例金属催化。从逆合成分析可知，Desbromoarborescidine A的全合成可以通过亚胺不对称催化还原进行关键的手性中心构建，而本课题组在之前的研究中通过手性有机小分子催化剂的发展，已将三氯硅烷氢转移还原亚胺发展成了一类简便实用、高效、高对映选择性并具有优良底物适应范围的不对称催化反应，我们希望以这一反应作为关键手段，发展一条Desbromoarborescidine A及其类似物不对称合成新路线。 根据我们设计的新路线，首先成功合成了其关键中间体，然后我们进行了关键的不对称催化尝试。用本实验室已有的高性能有机小分子催化剂虽得到了较好的对应选择性，但是产率很低。同时，为了验证整条线路的可行性，我们也用消旋的中间体进行拉通线路的尝试。但不幸的是，在脱除保护基时遇到了很大困难。尝试换不同的保护基，或改变脱保护基的顺序，都未能成功合成目标产物。究其原因可能是由于吲哚的特殊性造成的，吲哚类亚胺与常规的芳香亚胺有较大的差异，其NH基团无论保护还是不保护，对与其2位相联接的C=N双键均有很大的影响，导致其不对称催化还原难以进行。另外，由于所设计的还原产物含有处在吲哚苄位的胺基，稳定性较差，造成保护基脱除困难。 烯胺C-亚磺酰化反应是本课题组最近发现的一个新反应，之前未见文献报道。本研究对该反应进行了反应条件优化和底物扩展，发现带Cbz，Ac，COt-Bu，CO2Et，Bz等保护基的一系列环状和非环状烯胺在亚磺酸钠、DMAc和MeSiCl3的共同作用下能高效高产率生成β-胺基烯基亚砜类新化合物，为合成多官能团化的烯基亚砜新化合物提供了一条简便实用的途径。 The main constituent of Dracontomelum mangiferum B1, indoloquinolizidine alkaloid 10-Desbromoarborescidine A, has drawn great attention due to its calcium channel blocking activity. Its molecular structure is relatively simple compared with the other alkaloids of the same type, which has only one chiral center, albeit with four cycles A, B, C, and D. This compound is often used as a model target for exploring different strategies for the total synthesis of indole alkaloids. Nevertheless, so far there still lack practical and highly efficient methods for the asymmetric total synthesis of 10-Desbromoarborescidine A. Most of the current available methods rely on stoichiometric asymmetric synthesis for the construction of the chiral center. There is only one example reporting utilization of asymmetric catalysis, but with transition metal complex as the catalyst. Our retrosynthetic analysis shows that catalytic asymmetric reduction of imine could be used as the key step for the construction of the chiral center of Desbromoarborescidine A. Since in the previous studies our group has developed the asymmetric reduction of imines by trichlorosilane into a practical and highly efficient and enantioselective method using newly designed chiral organocatalysts, we hope to apply this method to develop a novel synthetic route for the total synthesis of Desbromoarborescidine A and its analogues in this study. According to the newly designed synthetic route, we first accomplished the synthesis of the key intermediates which was then examined for the critical asymmetric catalysis. The asymmetric reduction using the highly efficient organocatalysts, developed in our lab afforded high ee but poor yield. We tried different reaction conditions to improve the yield, but failed to get any good results. Simultaneously, to vertify the feasibility of the synthetic route we designed, we also tired to go through the route toward the racemic synthesis of Desbromoarborescidine A. But unfortunately, protection and deprotection proved to be big hurdles. All the different protection groups and different sequences of protection and deprotection we tried failed to get us through the designed synthetic sequence and furnish the final product. Most likely, the indole part is the culprit behind the failures.The NH group of the indole, no matter protected or not, may impact the catalytic asymmetric reduction of C-N double bond connected with 2-C. Additionally, the reduction product we designed contains an amino group in the β-position of the indole, which may cause problems due to its instability. C-sulfenylation of enamines is a novel reaction discovered recently by our group, which has not been seen before in the literature. In this study, optimization of the reaction conditions and exploration of the substrate scope were further undertaken for this reaction, which reveal that a series of enamines with N-Cbz, Ac, COt-Bu, CO2Et protection groups could all undergo smooth C-sulfinylations with the comined use of sodium benzene sulphinate, DAMc and MeSiCl3, efficiently furnishing the β-amino vinylsulfoxide products in high yield, affording a practical and highly efficient methods for synthesis of functional vinylsulfoxides.

岷江柏种子的形态和发芽特征与贮藏生理动态研究

岷江柏(Cupressus chenggiana S. Y. Hu)是我国川甘地区特有的珍稀濒危乔木，一般生长在干旱的河谷区，在涵养水源和保护水 土等方面起着重要的作用。本文选择4个岷江柏种群，采用了野外调查和室内实验相结合的研究方法，调查岷江柏种群结实状况， 分析种子和球果形态特征，阐明种子发芽的基本特征，研究岷江柏种子贮藏过程中几个生理指标的动态变化特点，目的是为岷江柏 种苗繁育、自然更新能力评估以及珍稀濒危机制分析提供理论依据。研究得出如下结论：1.岷江柏球果呈椭球形，长为1.5～ 2.2cm,宽为1.5～1.9cm，质量为1.7～4.2g，球果鳞片数量为8～11片，球果内种子数量一般在40～70粒。岷江柏种子为椭圆形，长 为3.58～4.02mm，宽为3.10～3.15mm，厚为0.96～1.11mm，千粒重为3.1～3.5g。岷江柏的结实率很低，并且有显著的地理差异和 大小年差异。2. 岷江柏种子发芽温度范围是5℃～30℃,其中种子的适宜发芽温度范围是10℃～25℃。种子最适发芽温度随着贮藏 时间的增加而变化。在适宜温度范围内，种子发芽周期为20d。温度对种子的发芽势和T50有显著影响，对种子发芽率没有显著影响 ；光照有利于种子发芽；岷江柏种子的发芽特征是岷江柏保护种子资源、防止物种濒危的一种环境适应，有助于岷江柏种子提高发 芽率和幼苗的存活率。岷江柏种子是一种耐贮藏的正常性种子，在短期贮藏过程中，贮藏温度和种子含水量对于种子生理指标和种 子发芽没有显著影响。3. 岷江柏种子在短期贮藏过程中，千粒重没有显著变化；含水量都经历了先下降，再稳定的过程；粗脂肪 含量和可溶性糖含量逐渐降低；可溶性蛋白含量和丙二醛含量逐渐增加；脯氨酸含量在贮藏1～7个月时变化差异不明显，但是贮藏 7～10个月后显著增加。岷江柏种子的各个生理指标之间的相关性差异不显著。4. 岷江柏球果和种子的形态特征存在显著的地理差 异。岷江柏种子的发芽能力的地理性差异不大，种群间差异不大。岷江柏种群的地理差异由种群特征、生境特征和气候特征共同决 定。5. 在岷江柏的人工繁育中，对于刚刚采集的种子，发芽温度在15℃～25℃比较适合，其中以25℃最佳；而对于短期贮藏(4～ 10个月)后的种子，发芽温度在10℃～25℃均可，以15℃～20℃为最佳。野外播种的最适时间为4～6月，6～9月的间歇性干旱和降 水波动可能是限制岷江柏自然更新的因素之一。在短期贮藏过程中，种子可以采用常规室温贮藏，可以节约成本。Cupressus chenggiana is a specific and endangered plant in Sichuan and Gansu provinces of China, and it usually grows in dry valley and plays an important role in water supply and soil and water conservation in the dry valley of alpine and canyon region of southwest China. The research selected four Cupressus chenggiana populations and used the methods of the field investigation and the lab experiments. The fruiting characters of Cupressus chenggiana populations, the morphological characters of seeds and cones, the germination characters of seeds and the store physiological dymatics of several factors of seeds have been studied in order to give some theoretical advices on the artificial propagation and the ability of natural regeneration and the endangered principle of Cupressus chenggiana in the paper. The main results may be clarified as follows: 1. The cones of Cupressus chenggiana are ellipsoidal, length ranged from 1.5 to 2.2cm, with ranged from 1.5 to 1.9 cm, weight ranged from 1.7 to 4.2g, the number of cone squama ranged from 8 to 11, and the seed number of per cone ranged from 40 to 70. The seeds of Cupressus chenggiana are elliptical, length ranged from 3.58 to 4.02 mm, width ranged from 3.10 to 3.15 mm, thickness ranged from 0.96 to 1.11 mm, and the weight of 1000 seeds ranged from 3.1 to 3.5g. The fruiting rate of Cupressus chenggiana is very low, and the fruiting period of Cupressus chenggiana has the geographical differences and the big or small year differences. 2. Seed germination temperature is between 5℃ and 30℃, while the suited temperature is between 10℃ and 25℃. The optimum temperature of seed germination will change as the store time of seeds changes logner. The cycle of seed germination can persist 20 days in the range of the suited temperature. The germination temperatures have significant influences on the germination potential and T50, but have no significant infuluences on the germination rate. The photoperiod is in favor of seed germination. The characters of Cupressus chenggiana seed germination represent a kind of environmental adaptability to protect the seed sources and endangered species, and it can give help to increase the germination rate of seeds and the livability of seedings. The seeds of Cupressus chenggiana are a kind of orthodox seeds that can endure the long time storage. In the short time storage, the store temperatures and the moisture contents of seeds have no significant infuluences on the physiological factors and the germination of seeds, but the store time has significant influences on the physiological factors of seeds. 3. In the short store course of Cupressus chenggianna seeds, the 1000 seed weight has no significant variation; The moisture content descends at the beginning of the storage, but has no significant variation later; The crude fat content and the soluble sugar content descend gradually; The soluble protein content and MDA content increase gradually; The praline content has no significant variation after 1～7 months storage, but increase significantly after 7～10 months storage. The correlations of different physiological factors are not significant. 4. The morphological characters of cones and seeds of four populations exist significant differences. The germination of Cupressus chenggiana seeds has no significant geographical variation. The geographical variation of Cupressus chenggiana populations can be ascribed to the population characters, climate and environment. 5. In the course of artificial propagation of Cupressus chenggiana, it is favored that the germination temperature of newly collected seeds is between 15℃ and 25℃, while the optimum temperature is 25℃. After the short storage ranged from 4 months to 10 months, it is favored that the germination temperature is between 10℃ and 25℃, while the optimum temperature is ranged from 15℃ to 20℃. The field sowing optimum time is between April and June, and the interval drought and fallrain fluctuation between July and September may be one of the reasons that restrict natural regeneration of Cupressus chenggiana. In the short storage, seeds can be stored in the condition of room temperature.

猪场废水短程硝化反硝化-厌氧氨氧化脱氮研究

畜禽废水是农村水环境污染的主要来源之一，其处理的难点在于脱氮。传统生物脱氮法具有能耗高、需大量外加碳源等缺点，开发低成本、高效率的新型生物脱氮技术具有重要意义。 本研究将短程硝化反硝化和厌氧氨氧化两种脱氮新技术结合，让前者为后者创造去除可降解COD、降低总氮负荷、调整pH、调整氨氮和亚硝酸盐氮浓度比例等进水条件，而后者可在无需外加碳源的条件下进一步脱氮，二者结合可成为高氨氮、低C/N废水脱氮的新途径。 试验以低碳氮比猪场废水为研究对象，首先进行了短程硝化反硝化预处理研究，同时启动并运行调控厌氧氨氧化反应器，最后以经过短程硝化反硝化预处理的猪场废水为进水，进行厌氧氨氧化脱氮考察。实验表明：（1）短程硝化反硝化作为厌氧氨氧化的预处理工序是可行的。猪场废水通过短程硝化反硝化，可以达到基本去除可生化COD、部分脱氮、控制出水氨氮和亚硝酸盐氮浓度之比在1︰1左右、pH在7.5～8.0的目的， COD和总氮平均去除率分别为64.3%、49.1%,出水可达到厌氧氨氧化反应的进水要求。（2）采用模拟废水启动厌氧氨氧化反应器，经过5个月左右的运行调控，反应器启动成功并稳定运行，最高总氮去除率为87.1%，总氮容积去除率最高达到0.14kg/m3.d；整个稳定阶段，氨氮、亚硝酸盐氮、硝酸盐氮的变化量之比为1︰1.21︰0.33。（3）经过短程硝化反硝化预处理的猪场废水厌氧氨氧化脱氮效果稳定，氨氮、亚硝酸盐氮、总氮、COD的平均去除率分别为93.0%、99.4%、84.6%、18.1%，处理效果与模拟废水处理系统相比无明显变化。（4）经过短程硝化反硝化预处理后，猪场废水中残留有机物成分在厌氧氨氧化反应过程中无显著变化，主要为酯类和烷烃类物质；残留有机物对厌氧氨氧化效果无明显影响。（5）采用PCR技术进行特殊功能菌种检测，结果表明模拟废水处理系统和猪场废水处理系统的菌群中均含有厌氧氨氧化菌和好氧硝化菌；通过blast比对，厌氧氨氧化菌扩增序列与未培养的Planctomycetales菌和Candidatus Brocadia fulgida菌16S rRNA部分序列相似性分别为95％、90%。（6）MPN法菌种计数结果显示，模拟废水处理系统和猪场废水处理系统的菌群中均含有硝化细菌、亚硝化细菌和少量反硝化菌，实验条件下的微生物系统是一个厌氧氨氧化菌与好氧硝化菌、反硝化菌共存的系统。 Poultry wastewater is one of the main source of water pollution in rural areas，and nitrogen removal is the most difficult part in treating poultry wastewater. There are some disadvantages in traditional nitrogen removal, such as high energy consumption and more additional organic carbon. It is important to develop ecolomical and efficient technologyies. Shortcut nitricfication/denitrification, as a pretreatment process, was combined with Anammox in this research, so that part of total nitrogen and most degradable COD could be removed by the former, and further nitrogen removal could be implemented by the latter. The combination of the two technologies was a new approach to treat wastewater with high ammonium and low C/N. Piggery wastewater with low C/N was treated in lab-scale experiment. Firstly, shortcut nitrification/denitrification was investigated, and Anammox reactor was started up successfully at the same time. Then piggery wastewater after pretreatment was treated by Anammox. The results showed :(1) It was feasible to take nitrification/denitrification as the pretreatment process of Anammox. By using this process, part of total nitrogen and COD were removed, the ratio of ammonium and nitrite reached around 1︰1 and the pH was about 7.8, which were favorable for Anammox. The average removal percentage of COD and total nitrogen were about 64.3% and 49.1%, respectively. (2) Simulated wastewater was used to start up Anammox reactor. The reactor was started up successfully within 5 months and stable performance was achieved. The highest nitrogen removal reached 87.1% and the biggest volumetric total nitrogen removal rate reached 0.14kg/m3.d. The average ratio of ammonium, nitrite and nitrate was 1:1.21:0.33. (3)Taking the effluent of shortcut nitrification/denitrification as the influent, the nitrogen removal efficiency of Anammox was stable, and the the average removal percentage of ammonium, nitrite, total nitrogen and COD were 93.0%, 99.4% , 84.6% and 18.1%, respectively, which had little difference with that by using simulated wastewater..(4) After pretreatment, the residual organic carbon in piggery wastewater showed no obvious change during the Anammox process, and the main organic compounds were saturated hydrocarbon and ester, which had no obvious negative effect on Anammox process.(5) By PCR technology, the existence of Anammox bacteria was confirmed and the aerobic nitrifying bacteria was found to coexist as well. The result of blast showed that the identities of Anammox bacterium to part of 16S rRNA sequence of uncultured Planctomycetales bacterium and Candidatus Brocadia fulgida bacterium were 95% and 90%, respectively.（6）By MPN method, nitrite oxidizer, ammonium oxidizer and denitrification bacteria were detected in both simulated and piggery wastewater treatment system of Anammox, and the microorganism system was composed of Anammox bacteria，aerobic bacteria and denitrification bacteria together.

垃圾渗滤液场外硝化－原位反硝化脱氮协同填埋场温室气体减排

垃圾卫生填埋是国内外城市垃圾的主要处置方法。垃圾渗滤液是渗入填埋场垃圾的降水混合垃圾降解过程中产生的物质而形成的混合物，是垃圾填埋场向环境排放的主要污染物。渗滤液由于其所含高浓度有机和无机污染物，且其中很多物质有生物毒性或难生物降解，难于治理。特别是到填埋晚期，渗滤液中高浓度的氨氮更是增加了治理的难度。渗滤液场外硝化－原位反硝化是填埋场氮管理的新途径。本文利用从环境中筛选出优势硝化功能菌对渗滤液中的高浓度氨氮进行生物硝化，经硝化后的渗滤液回灌至以垃圾柱模拟的生物反应器填埋场，在填埋场内实现原位反硝化。 上述目标通过以下两部分来实现： 第一部分：渗滤液场外硝化。首先从污水厂的硝化污泥中富集并筛选出硝化功能菌，在模拟氨氮废水中优化。将驯化的硝化功能菌接种于连续式完全混合反应器（CSTR）进行高氨氮渗滤液硝化研究。在200余天的连续运行中，反应器硝化和有机物去除效果良好。在最大氨氮负荷和有机物负荷分别为0.65 g N l-1 d-1 和3.84 g COD l-1 d-1时，氨氮和COD去除率分别高于99%和57%。实验过程中发现，游离氨（FA）和溶解氧（DO）浓度对反应器中亚硝酸盐的积累影响很大。 第二部分：渗滤液原位反硝化。本文利用一个垃圾填充柱模拟生物反应器填埋场，研究了硝化渗滤液回灌对垃圾降解的影响，和回灌的硝化渗滤液中TON（总氧化态氮）对填埋场生物反应器产甲烷作用的影响。最后利用变性梯度凝胶电泳（DGGE）分析了硝化渗滤液回灌对垃圾填埋场菌群结构的影响。结果表明：回灌的TON被完全还原，反硝化为主要反应，最大TON负荷为28.6 mg N kg-1 TS d-1。当垃圾柱TON负荷大于11.4 mg N kg-1 TS d-1时，出现了产甲烷抑制，抑制作用随TON负荷的增加而加强。在此过程中，反硝化逐渐代替产甲烷作用成为填埋场内垃圾降解的主要反应，且更多产生的是清洁的氮气，而非温室气体甲烷。直到实验结束时，回灌硝化渗滤液的垃圾柱的甲烷产量仅相当于对照的2.5%，并且回灌的硝化渗滤液还加速了填埋场垃圾的降解与稳定。通过DGGE进行菌群结构分析发现，由于TON对填埋场的长期作用，反硝化菌增多而产甲烷菌减少。 Landfill still remains the chief method for MSW management around the world. Leachate is a mixture of rainfall permeating through landfill and organic and inorganic matters generated during decomposition of the wastes in the landfills, characterized as highly complicated and refractory wastewater. Ex-situ nitrification and sequential in-situ denitrification represents a novel approach to nitrogen management at landfills. In the present paper, nitrification was carried out in a continuous stirred tank reactor (CSTR) inoculated with nitrifying bacteria which were isolated from municipal WWTP of Chengdu city. The nitrified leachate from CSTR was recirculated to a lab-scale municipal solid waste (MSW) column where in-situ denitrification took place. The above object was achived through two parts as following: First, ex-situ nitification of leachate. After acclimated in simulated wastewater for 3 month, nitrifying bacteria isolated from WWTP nitrifying sludge were added to the CSTR for nitrification. The results over 200 days showed that the maximum nitrogen loading rate (NLR) and the maximum organic loading rate (OLR) was 0.65 g N l-1 d-1 and 3.84 g COD l-1 d-1, respectively. The ammonia and COD removal was over 99% and 57%, respectively. Moreover, the effects of free ammonia (FA) and dissolved oxygen (DO) on nitrification were investigated. Second, in-situ denitrification was studied in a municipal solid waste (MSW) column. Variation of nitrified leachate and its effects on the decomposition of municipal solid waste (MSW) were studied in a lab-scale MSW column to which nitrified leachate was recirculated. Additionally, DGGE was employed to investigate the microbial community of both MSW columns. The results suggested: complete reduction of total oxidized nitrogen (TON) was obtained with maximum TON load of 28.6 mg N kg-1 TS d-1 and denitrification was the main reaction responsible. Methanogenesis inhibition was observed while TON load was over 11.4 mg N kg-1 TS d-1 and the inhibition was enhanced with the increase of TON load. Denitrification gradually took over methanogenesis to become the main reaction responsible for decomposition of MSW while nitrogen gas, a clean byproduct, was generated instead. Till the end of the experiment, the average weekly methane production in the denitrification column was as low as 2.5% of that of the control, and the rate of decompition and stability of MSW was accelerated by the recirculation of the nitrified leachate.Owing to long term exposure of nitrified leachate to landfill, denitrifying bacteria increased and methanogen decreased.