Novel coupled multi-active region high power semiconductor lasers cascaded via tunnel junction

A novel semiconductor laser structure is put forward to resolve the major difficulties of high power laser diodes. In this structure, several active regions are cascaded by tunnel junctions to form a large optical cavity and to achieve super high efficiency. This structure can solve the problems of catastrophic optical damage of facet, thermal damage and poor light beam quality effectively. Low-pressure metalorganic chemical vapor deposition method is adopted to grow the novel semiconductor laser structures, which are composed of Si:GaAs/C:GaAs tunnel junctions, GaAs/InGaAs strain quantum well active regions. External differential quantum efficiency as high as 2.2 and light power output of 2.5 W per facet (under 2A drive current) are achieved from an uncoated novel laser device with three active regions.

Room temperature (34 degrees C) operation of strain-compensated quantum cascade lasers

A short wavelength (lambda similar or equal to 3.5 mu m) strain-compensated InxGa(1-x)As/InyAl(1-y)As quantum cascade laser is reported. Quasi-continuous wave operation of this device at 34 degrees C with an output power of 11.4mW persisted for more than 30 minutes without obvious degradation. A very low threshold current density of 1.2KA/cm(2) at this temperature was observed.

Investigation on anisotropy of vertical-cavity surface-emitting lasers

We have studied the spontaneous emission of polarized excitons in the GaInP/AlGaInP vertical-cavity surface-emitting lasers from 50 K to room temperature. It is observed that the spontaneous emission peak enters and leaves the resonant regime. At the resonant regime, the emission intensities of the perpendicularly and horizontally polarized excitons are enhanced and their proportions are different from that in nonresonant regime. These experimental results are explained by the dressed exciton theory of the semiconductor microcavity device. Based on this theory, the intensity enhancement and the polarization dependence are understood as cooperative emission and the microcavity anisotropy. (C) 2000 American Institute of Physics. [S0021-8979(00)05315-9].

High power 980 nm Al-free strained quantum-well lasers for erbium-doped fiber amplifiers

In this paper, we reported on the fabrication of 980 nm InGaAs/InGaAsP strained quantum-well (QW) lasers with broad waveguide. The laser structure was grown by low-pressure metalorganic chemical vapor deposition on a n(+)- GaAs substrate. For 3 mu m stripe ridge waveguide lasers, the threshold current is 30 mA and the maximum output power and the output power operating in fundamental mode are 350 mW and 200 mW, respectively. The output power from the single mode fiber is up to 100 mW, the coupling efficiency is 50%. We also fabricated 100 mu m broad stripe coated lasers with cavity length of 800 mu m, a threshold current density of 170 A/cm(2), a high slope efficiency of 1.03 W/A and a far-field pattern of 40 x 6 degrees are obtained. The maximum output power of 3.5 W is also obtained for 100 mu m wide coated lasers. (C) 2000 Elsevier Science B.V. All rights reserved.

High-speed and high-power 1.3 mu m InGaAsP/InP selective proton-bombarded buried crescent lasers with optical field attenuation regions

High-speed and high-power InGaAsP/lnP selective proton-bombarded buried crescent (SPB-BC) lasers with optical field attenuation regions were reported. The defect of proton bombardment can not affect the lifetime of the SPB-BC laser because the optical field attenuation region obstructs the growth and propagation of defects. A CW light output over 115 mW was achieved at room temperature using a 500 mu m long cavity SPB-BC laser. The 3 dB bandwidth was 8.5 GHz, and the lifetime was about 8.5 x 10(5) h. The capacitance of four kinds of current blocking structures was first measured in our experiment, and the results shown that the capacitance of proton-bombarded pnpn structure was not only less than that of pnpn current blocking structure, but also less than that of semi-insulating Fe-InP structure.

Influence of lateral propagating modes on laser output characteristics in selectively oxidized vertical cavity surface-emitting lasers with double oxide layers

The influence of lateral propagating modes on the threshold current and the spontaneous emission factor in selectively oxidized vertical cavity surface-emitting lasers (VCSELs) is investigated based on the mode behaviors of lateral propagating modes and the rate equation model. The numerical results show that the lateral propagating modes may be trapped in the aperture region for the selectively oxidized VCSEL with two oxide layers, one above and one below the active region. The output characteristics of VCSELs can be affected due to the reabsorption of the quasitrapped lateral propagating modes. A lower threshold current can be expected for a VCSEL with double oxide layers than that with a single oxide layer. The numerical results of rate equations also show that a larger spontaneous emission factor can be obtained by fitting the output-input curves for the VCSEL with double oxide layers. (C) 1999 American Institute of Physics. [S0021-8979(99)07919-0].

AlGaInP visible quantum well lasers for information technology

650 nm-range AlGaInP multi-quantum well (MQW) laser diodes grown by low pressure metal organic chemical vapor deposition (LP-MOCVD) have been studied and the results are presented in this paper. Threshold current density of broad area contact laser diodes can be as low as 350 A/cm(2). Laser diodes with buried-ridge strip waveguide structures were made, threshold currents and differential efficiencies are (22-40) mA and (0.2-0.7) mW/mA, respectively. Typical output power for the laser diodes is 5 mW, maximum output power of 15 mW has been obtained. Their operation temperature can be up to 90 degrees C under power of 5 mW. After operating under 90 degrees C and 5 mW for 72 hrs, the average increments for the threshold currents of the lasers at 25 degrees C and the operation currents at 5 mW (at 25 degrees C) are (2-3) mA and (3-5) mA, respectively. Reliability tests showed that no obvious degradation was observed after 1400 hours of CW operation under 50 degrees C and 2.5 mW.

Native-oxidized InAlAs blocking layer buried heterostructure InGaAsP-InP MQW laser for high-temperature operation

A novel idea of InAlAs native oxide utilized to replace the p-n-p-n thyristor blocking layer and improve the high-temperature performance of buried heterostructure InGaAsP-InP laser is first proposed and demonstrated. A characteristic temperature (T-0) of 50 K is achieved from an InA1As native oxide buried heterostructure (NOBH) InGaAsP-InP multiquantum-well laser with 1.5-mu m-wide diode leakage passage path. The threshold current and slope efficiency of NOBH laser changes from 5.6 mA, 0.23 mW/mA to 28 mA, 0.11 mW/mA with the operating temperature changing from 20 degrees C to 100 degrees C. It is comparable to conventional p-n reverse biased junction BH laser with minimized diode leakage current, and is much better than the buried ridge strip with proton implanted laterally confinement laser.

Threshold reduction in strained-layer InGaAs/GaAs quantum well lasers by liquid phase epitaxy regrowth

When liquid phase epitaxy regrowth at 780 degrees C for 2 h is applied to the samples after molecular beam epitaxy, a decrease of the threshold current density in strained InGaAs/GaAs quantum well lasers by a factor of 3 to 4 is obtained. We suggest that this improvement is attributed to the reduction of nonradiative centers associated with deep levels at the three regions of the active region, the graded layer and the cladding layer. Indeed, a significant reduction of deep center densities has been observed by using minority and majority carrier injection deep level transient spectroscopy measurements. (C) 1998 Elsevier Science B.V. All rights reserved.

Effect of reflectivity at the interface of oxide layer on transverse mode control in oxide confined vertical-cavity surface-emitting lasers

The transverse mode control in oxide confined vertical-cavity surface-emitting lasers is discussed by modeling the dielectric aperture as a uniform waveguide and an extra reflectivity at the oxide layer. The phase of the extra reflectivity and the refractive index step can be adjusted to change the mode threshold gain. We calculate the lateral refractive index step from the mode wavelength difference between aperture and perimeter modes, and compare it with that obtained from the weighted average index. The mode reflectivity in terms of the lateral optical confinement factor at the oxide layer is considered in calculating the threshold gain for transverse modes. The numerical results show that higher transverse modes can be suppressed by adjusting the position of a thin AlAs-oxide layer inside a three-quarter-wave layer in the distributed Bragg reflector. (C) 1998 American Institute of Physics. [S0021-8979(98)04007-9].

Theoretical investigation on quantum well lasers with extremely low vertical beam divergence and low threshold current

A specially designed quantum well laser for achieving extremely low vertical beam divergence was reported and theoretically investigated. The laser structure was characterized by two low index layers inserted between the waveguide layers and the cladding layers. The additional layers were intended to achieve wide optical spread in the cladding layers and strong confinement in the active region. This enabled significant reduction of beam divergence with no sacrifice in threshold current density. The numerical results showed that lasers with extremely low vertical beam divergence from 20 degrees down to 11 degrees and threshold current density of less than 131 A/cm(2) can be easily achieved by optimization of the structure parameters. Influences of individual key structure parameters on beam divergence and threshold current density are analyzed. Attention is also paid to the minimum cladding layer thicknesses needed to maintain low threshold current densities and low internal loss. The near and far field patterns are given and discussed. (C) 1998 American Institute of Physics.

Hydrogen sensors based on Pt-AlGaN/GaN back-to-back Schottky diode

In this paper, platinum (Pt) with a thickness of 45 nm was sputtered on the surface of AlGaN/GaN heterostructure to form the Schottky contact and the back-to-back Schottky diodes were characterized for H-2 sensing at room temperature. Both the forward and reverse current of the devices increased with exposure to H-2 gas, which was attributed to Schottky barrier height reduction caused by hydrogen absorption in the catalytic metals. A shift of 0.7 V at 297 K was obtained at a fixed forward current of 0.1 mA after switching from N-2 to 40% H-2 in N-2. The sensor's responses under different concentrations from 2500 ppm H-2 to 40% H-2 in N-2 at 297 K were investigated. Time response of the sensor at a fixed bias of 1 V was given. Finally, the decrease of the Schottky barrier height and the sensitivity of the sensor were calculated. (C) 2008 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Superluminescent diode monolithically integrated with novel Y-branch by bundle integrated waveguide for fiber optic gyroscope - art. no. 68380D

We have developed a novel InP-based, ridge-waveguide photonic integrated circuit (PIC), which consists of a 1.1-um wavelength Y-branch optical waveguide with low loss and improved far field pattern and a 1.3-um wavelength strained InGaAsP-InP multiple quantum-well superluminescent diode, with bundle integrated guide (BIG) as the scheme for monolithic integration. The simulations of BIG and Y-branches show low losses and improved far-field patterns, based on the beam propagation method (BPM). The amplified spontaneous emission of the device is up to 10 mW at 120 mA with no threshold and saturation. Spectral characteristics of about 30 nm width and less than I dB modulation are achieved using the built-in anti-lasing ability of Y-branch. The beam divergence angles in horizontal and vertical directions are optimized to as small as 12 degrees x8 degrees, resulting in good fiber coupling. The compactness, simplicity in fabrication, good superluminescent performance, low transmission loss and estimated low coupling loss prove the BIG and Y-branch method to be a feasible way for integration and make the photonic integrated circuit of Y-branch and superluminescent diode an promising candidate for transmitter and transceiver used in fiber optic gyroscope.

Hydrogen sensors based on Pt-AlGN/AIN/GaN Schottky diode - art. no. 68291R

Pt/AlGaN/AlN/GaN Schottky diodes have been fabricated and characterized for H-2 sensing. Platinum (Pt) with a thickness of 20nm was evaporated on the sample to form the Schottky contact. The ohmic contact, formed by evaporated Ti/Al/Ni/Au metals, was subsequently annealed by a rapid thermal treatment at 860 degrees C for 30 s in N-2 ambience. Both the forward and reverse current of the device increased greatly when exposed to H-2 gas. The sensor's responses under different hydrogen concentrations from 500ppm to 10% H-2 in N-2 at 300K were investigated. A shift of 0.45V at 297K is obtained at a fixed forward current for switching from N-2 to 10% H-2 in N-2. Time response of the sensor at a fixed bias of 0.5 V was also measured. The turn-on response of the device was rapid, while the recovery of the sensor at N-2 atmosphere was rather slow. But it recovered quickly when the device was exposed to the air. The decrease in the barrier height of the diode was calculated to be about 160meV upon introduction of 10% H-2 into the ambient. The sensitivity of the sensor is also calculated. Some thermodynamics analyses have been done according to the Langmuir isotherm equation.

High-performance multiplexed vibration sensor system based on fiber lasers - art. no. 683019

This paper describes a high-performance multiplexed vibration sensor system using fiber lasers. A serial vibration sensor array consists of four short cavity fiber lasers. The system employs a single, polarization-insensitive, unbalanced Michelson interferometer to translate individual laser wavelength shifts induced by vibration signals into interferometer phase shifts. A dense wavelength division demultiplexor (DWDM) with high channel isolation is inserted to demultiplex each laser signal as a wavelength filter. Finally, a digital phase demodulator based on the phase generated carrier technique is used to achieve high-resolution interrogation. Experimental results show that no observable crosstalk is measured on the output channels, and the minimal detectable acceleration of this system is similar to 200ng/root Hz at 250Hz, which is fundamentally limited by the frequency noise of the lasers.