Rearrangeable nonblocking thermo-optic 4 x 4 switching matrix in silicon-on-insulator

A rearrangeable nonblocking thermo-optic 4 x 4 switching matrix is demonstrated. The matrix, which consists of five 2 x 2 multimode interference-based Mach-Zehnder interferometer (MMI-MZI) switch elements, is fabricated in silicon-on-insulator waveguide system. The average excess loss for the optical path experiencing 2 and 3 switch elements is 6.6 and 10.1 dB respectively. The crosstalk in the matrix is measured to be between -12 and -19 dB. The switching time of the device is less than 30 mu s.

Thermo-optical switch matrix based on silicon-on-insulator waveguides

A thermo-optical waveguide switch matrix is designed and fabricated on silicon-on-insulator wafer. Multi-mode interferometers are used as power splitters and combiners in a Mach-Zehnder structure. Inductively coupled plasma reactive ion etching is used to fabricate the waveguides. The rise and fall times of the switch matrix are 13 mu s and 7 mu s, respectively. Switch cells have an average switching power consumption of 340 mW.

A short carrier lifetime semiconductor optical amplifier with n-type modulation-doped multiple quantum well structure

Semiconductor optical amplifiers (SOAs) with n-type modulation-doped multiple quantum well structure have been investigated. The shortened carrier lifetime is derived from the PL spectrum and electrical modulation frequency response measurement. The carrier lifetime in semiconductor optical amplifiers with any n-type-2-modulated doping multiple quantum well structure is less than 60% of that in the undoped partner. The shortest measured carrier lifetime of 236 ps in the MD-MQW SOA with sheet carrier density of 3 x 10(12) cm(-2) was only 38% of that in the undoped MQW SOA, which can increase the wavelength conversion efficiency via four wave mixing by a factor of about 7 and switching speed via XGM and XPM applications by a factor of 2.63.

Novel folding 8x8 silicon-based optical matrix switch with tapered waveguides and self-aligned corner mirrors

Novel folding 8 x 8 matrix switches based on silicon on insulator were demonstrated. In the design, single-mode rib waveguides and multimode interferences are connected by optimized tapered waveguides to reduce the mode coupling loss between the two types of waveguides. The self-aligned method was applied to the key integrated turning mirrors for perfect positions and low loss of them. A mixed etching process including inductively coupled plasma and chemical etching was employed to etch waveguides and mirrors, respectively. The compact size of the device is only 20 x 3.2 mm(2). The switch element with high switching speed and low power consumption is presented in the matrix. The average insertion loss of the matrix is about -21 dB, and the excess loss of one mirror is measured of -1.4 dB. The worst crosstalk is larger than 21 dB. Experimental results illuminate that some of the main characteristics of optical matrix switches are. developed in the modified design, which is in accord with theoretic analyses.

Photon-storage in optical memory cells based on a semiconductor quantum dot-quantum well hybrid structure

We report a new type of photonic memory cell based on a semiconductor quantum dot (QD)-quantum well (QW) hybrid structure, in which photo-generated excitons can be decomposed into separated electrons and holes, and stored in QW and QDs respectively. Storage and retrieval of photonic signals are verified by time-resolved photoluminescence experiments. A storage time in excess of 100ms has been obtained at a temperature of 10 K while the switching speed reaches the order of ten megahertz.

Design of Si-based Electro-optical modulator employed dual capacitors - art. no. 68381B

Electro-optical modulator with dual capacitors is designed and based on this design basic configuration of device is realized in laboratory. Exceeding GHz switching speed and high phase modulation efficiency can be expected with this device.

Parallel optical communication subsystem based on VCSEL - art. no. 67833I

A parallel optical communication subsystem based on a 12 channels parallel optical transmitter module and a 12 channels parallel optical receiver module can be used as a 10Gbps STM-64 or an OC-192 optical transponder. The bit error rate of this parallel optical communication subsystem is about 0 under the test by SDH optical transport tester during three hours and eighteen minutes.

Novel compact SOI-based reconfigurable optical add/drop multiplexer using microring resonators - art. no. 60190L

Novel compact design for 4-channel SOI-based reconfigurable optical add/drop multiplexer using microring resonators is presented and analyzed. Microring resonators have two important attributes as a key new technology for future optical communications, namely functionality and compactness. Functionality refers to the fact that a wide range of desirable filter characteristics can be synthesized by coupling multiple rings. Compactness refers the fact that ring resonators with radii about 30 mu m can lead to large scale integration of devices with densities on the order of 10(4) similar to 10(5) devices per square centimeter. A 4-channel reconfigurable optical add/drop multiplexer comprises a grid-like array of ridge waveguides which perpendicularly cross through each other. SOI-based resonators consisted of multiple rings at each of the cross-grid nodes serve as the wavelength selective switch, and they can switch an optical signal between two ports by means of tuning refractive index of one of the rings. The thermo-optic coefficient of silicon is 1.86x 10(-4) /K. Thus a temperature rise of 27K will increase the refractive index by 5 x 10(-3), which is enough to cause the switching of our designed microring resonators. The thermo-optic effect is used to suppress the resonator power transfer, rather than to promote loss. Thus, the input signal only suffers small attenuation and simultaneously low crosstalk can be achieved by using multiple rings.

VCSEL-based parallel optical transmission module

This paper describes the design process and performance of the optimized parallel optical transmission module. Based on 1x12 VCSEL (Vertical Cavity Surface Emitting Laser) array, we designed and fabricated the high speed parallel optical modules. Our parallel optical module contains a 1x12 VCSEL array, a 12 channel CMOS laser driver circuit, a high speed PCB (Printed Circuit Board), a MT fiber connector and a packaging housing. The L-I-V characteristics of the 850nm VCSEL was measured at the operating current 8mA, 3dB frequency bandwidth more than 3GHz and the optical output 1mW. The transmission rate of all 12 channels is 30Gbit/s, with a single channel 2.5Gbit/s. By adopting the integration of the 1x12 VCSEL array and the driver array, we make a high speed PCB (Printed Circuit Board) to provide the optoelectronic chip with the operating voltage and high speed signals current. The LVDS (Low-Voltage Differential Signals) was set as the input signal to achieve better high frequency performance. The active coupling was adopted with a MT connector (8 degrees slant fiber array). We used the Small Form Factor Pluggable (SFP) packaging. With the edge connector, the module could be inserted into the system dispense with bonding process.

Optical properties and electrical bistability of CdS nanoparticles synthesized in dodecanethiol

We reported the synthesis of CdS semiconductor nanoparticles using a simple one-pot reaction by thermolysis of cadmium acetylacetonate in dodecanethiol. Optical measurements of the as-obtained CdS nanoparticles revealed that their optical properties were closely related to surface effects. Based upon the cocktail of poly (N-vinylcarbazole) (PVK) and CdS nanoparticles, a bistable device was fabricated by a simple solution processing technique. Such a device exhibited a remarkable electrical bistability, which was attributed to the electric field-assisted charge transfer between PVK and the CdS nanoparticles capped by dodecaethiol. The conduction mechanism changed from an injection-controlled current to a bulk-controlled one during switching from OFF-state to ON-state.

Integrated MMI Optical Couplers and Optical Switches in Silicon-on-Insulator Technology

Integrated multimode interference (MMI) coupler based on silicon-on-insulator(SOI) has been becoming a kind of more and more attractive device in optical systems. SiO2thin cladding layers (＜1.0 μm) can be usedin SOI waveguide due to the large index step be-tween Si and SiO2, making them compatible with VLSI technology. The design and fabrica-tion of MMI optical couplers and optical switches in SOI technology are presented in thepa-per. We demonstrated the switching time of 2 × 2 MMI-MZI thermo-optical switch is less than 20 μs:

Polarization switching current of vertical cavity surface-emitting Lasers in an applied electric field

The polarization of vertical-cavity surface-emitting laser (VCSEL) can be controlled by electro-optic birefringence. We calculated the birefringence resulted from external electric field which was imposed on the top DBR of VCSEL by assuming that the two polarization modes were in the same place of the gain spectra in the absence of electric field beginning. By modifying SFM, the affection of the electric field strength on the polarization switching currents between the two polarization modes had been shown.

Strain effects on optical polarisation properties in (11(2)over-bar2) plane GaN films

We present the theoretical results of the electronic band structure of wurtzite GaN films under biaxial strains in the (11 (2) over bar2)-plane The calculations are performed by the kappa p perturbation theory approach through using the effective-mass Hamiltonian for an arbitrary direction The results show that the transition energies decrease with the biaxial strains changing from -0 5% to 0 5% For films of (11 (2) over bar2)-plane, the strains are expected to be anisotropic in the growth plane Such anisotropic strains give rise to valence band mixing which results in dramatic change in optical polarisation property The strain can also result in optical polarisation switching phenomena Finally, we discuss the applications of these properties to the (11 (2) over bar2) plane GaN based light emitting diode and lase diode

Electrically-controlled near-infrared chiroptical switching of enantiomeric dinuclear ruthenium complexes

Enantiomerically pure dinuclear ruthenium complexes with 1,2-dicarbonylhydrazide as a bridging ligand are optically active in the visible and near infrared spectral regions depending on the oxidation states of the metal centers and are useful as an electrochemically driven near infrared chiroptical switch.

Optical Diagnostic and Modeling Solution Growth Process of Sodium Chlorate Crystals

Both a real time optical interferometric experiment and a numerical simulation of two-dimension non-steady state model were employed to study the growth process of aqueous sodium chlorate crystals. The parameters such as solution concentration distribution, crystal dimensions, growth rate and velocity field were obtained by both experiment and numerical simulation. The influence of earth gravity during crystal growth process was analyzed. A reasonable theory model corresponding to the present experiment is advanced. The thickness of concentration boundary layer was investigated especially. The results from the experiment and numerical simulation match well.