Memory devices based on lanthanide (SM3+, EU3+, Gd3+) complexes

Memory effects in single-layer organic light-emitting devices based on Sm3+, Gd3+, and Eu3+ rare earth complexes were realized. The device structure was indium-tin-oxide (ITO)/3,4-poly(ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT)/Poly(N-vinyl carbazole) (PVK): rare earth complex/LiF/Ca/Ag. It was found experimentally that all the devices exhibited two distinctive bistable conductivity states in current-voltage characteristics by applying negative starting voltage, and more than 10(6) write-read-erase-reread cycles were achieved without degradation. Our results indicate that the rare earth organic complexes are promising materials for high-density, low-cost memory application besides the potential application as organic light-emitting materials in display devices.

A wide-bandgap semiconducting polymer for ultraviolet and blue light emitting diodes

A novel wide-bandgap conjugated polymer (PDHFSCHD) consisting of alternating dihexylfluorene and rigidly twisted biphenyl units has been synthesized. The new fluorene-based copolymer composed of rigid twisting segments in the main-chain exhibits an optical bandgap of as high as 3.26 eV, and a highly efficient ultraviolet emission with peaks at 368 nm and 386 nm. An electroluminescence device from PDHFSCHD neat film as an active layer shows UV emission which peaks at 395 nm with a turn on voltage below 8 V By optimizing the device conditions, a peak EL quantum efficiency of 0.054% and brightness of 10 cd.m(-2) was obtained. Furthermore, blending a poly(dihexylfluorene) in the PDHFSCHD host gave pure blue emission peaking at 417 nm, and 440 nm without long wavelength emission from aggregated species. Efficient energy transfer from PDHFSCHD to PDHF was demonstrated in these blended systems. Depressed chain-aggregation of PDHF in the PDHFSCHD host can correspond to pure blue emission behaviors.

Stimulated emission in the film of polymer/dye blend

Optically pumped stimulated emission behavior in an organic film was demonstrated in this study. The gain material consists of a laser dye perylene doped into polystyrene (PS) matrix in an appropriate weight ratio. The sample was transversely pumped by the three harmonic output of a mode-locked Nd:YAG laser. The change of the emission spectra showed a clear threshold action and gain narrowing phenomenon when increasing the excitation intensity. Three emission peaks were observed below the excitation threshold, which are locate at 446, 475 and 506 nm, respectively. However, only the gain narrowing peak centered at 475 nm could be detected above the threshold. The spectra narrowing observed results from the amplified spontaneous emission (ASE) in the gain material. (C) 2000 Elsevier Science S.A. All rights reserved.

飞秒激光脉冲照射诱导含芴结构树脂共聚物结构变化及机理的研究

在室温下用聚焦的飞秒激光照射高折射率、低双折射的透明含芴结构树脂-对苯二甲酸乙二醇酯(PET)共聚物，探索飞秒激光制备高分子光学功能微结构的可能性。通过紫外-可见吸收光谱、红外光谱、电子自旋共振谱、光学显微镜、扫描电镜及透射电镜等分析手段，对该材料在飞秒激光照射后的结构变化及机理进行研究。结果发现：含芴结构树脂共聚物在飞秒激光照射后产生化学键断裂，生成未成对电子，并形成无定形碳；照射区在可见光区域的吸收增强；随激光能量密度的减少在激光会聚点附近诱导结构由慧尾状向单一细丝转变。演示了三维着色内雕。

The application of SnS nanoparticles to bulk heterojunction solar cells

Tin mono-sulphide (SnS) nanoparticles were synthesized by a facile method. Reactions producing narrow size distribution SnS nanoparticles with the diameter of 5.0-10 nm were carried out in an ethylene glycol solution at 150 degrees C for 24 h. Bulk heterojunction solar cells with the structure of indium tin oxide (ITO)/polyethylenedioxythiophene polystyrenesulphonate (PEDOT PSS)/SnS polymer/Al were fabricated by blending the nanoparticles with a conjugated polymer to form the active layer for the first time. Current density-voltage characterization of the devices showed that due to the addition of SnS nanoparticles to the polymer film, the device performance can be dramatically improved, compared with that of the pristine polymer solar cells. (c) 2009 Published by Elsevier B.V.

传输型电致发光聚合物的合成与表征

高分子发光材料除应具有优良发光性能外，还需具有优良电子传输性能和空穴传输性能。本论文以此为出发点，将具有优良空穴传输性能的芳胺类化合物和具有优良电子传输性能的噁二唑类化合物，通过无规共聚合调控发光基元和两类传输基元的含量，合成了系列的传输与发光一体化的即V类高分子发光材料，并探讨了聚合物本身的基本特性。同时，设计和制备了相应的单层结构器件和掺杂器件，考察了器件的器件性能。本论文主要工作内容及结果如下：1、成功的利用三类王芳胺类双醛：4，4'-二醛基-（4-辛氧基-苯基）-二苯胺（TPA双醛）、N，N'-二（4-辛氧基一苯基）-N，N'-二（4-甲醛基-苯基）-1，4-苯二胺（PDA双醛）和N，N，-二（4-辛氧基-苯基）-N，N，-二（4-甲醛基-苯基）-4，4' 联苯二胺（TPD双醛）和wittig麟盐无规共聚，得到三个系列双极传输高分子发光材料。2、聚合物主链中同时引入三芳胺类空穴传输基团和噁二唑电子传输基团，提高了器件性能。在TPA系列中，同时含有三芳胺和噁二唑全基团的聚合物比仅含有三芳胺基团聚合物的单层器件亮度及效率分别提高29和22倍，同时使器件的启动电压从9.3V下降到2．7V。在同样比较的情况下，在PDA系列中，聚合物的器件亮度及效率要提高近8倍，同时使器件的启动电压从5.3V下降到4.5V。在TPD系列中，聚合物的器件亮度及效率要提高44和38倍，同时使器件的启动电压从7.5V下降到5.7V。3、含有噁二唑基团聚合物分子的这种D-A体系所具有的分子内电荷转移性质，导致其荧光光谱和电致发光光谱红移。其中，TPA系列和TPD系列的电致发光光谱从绿光红移到了黄绿光，而PDA系列聚合物的电致发光光谱从黄绿光红移到了橙光。4、刚性的噁二唑基团的引入提高了聚合物的热稳定性，T以系列聚合物、PDA系列聚合物和TPD系列聚合物中含有噁二唑基团的聚合物的玻璃化转变温度在112-229℃之间，其热分解温度超过420℃。5、此三个系列聚合物中同时含有空穴和电子传输基元的双极分子溶液的紫外一可见吸收光谱和荧光光谱都有明显的溶剂化效应，表现出较强的分子内电荷转移特性。6、利用TPA系列聚合物中性能最好的聚合物TPA-OXD-PV1的良好电子和空穴传输性质，构造的单层掺杂器件，实现了橙色和红色发光。

High PL-efficiency ZnO nanocrystallites/PPV composite nanofibers

In this paper, we report for the first time on the synthesis of ZnO nanocrystallites in conjugated polymer (PPV) nanofibers by the coupling of the in situ/blend methods and electrospinning. These composite nanofibers were characterized by fluorescence microscopy, atomic force microscope (AFM), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), photoluminescence (PL) spectra, Fourier transform infrared (FT-IR) spectroscopy, and X-ray powder diffraction (XRD).

Morphology and crystalline transition of poly (3-butylthiophene) associated with its polymorphic modifications

Poly (3-butylthiophene) (P3BT) is a much less studied conjugated polymer despite its high crystallizability and thus excellent electrical property. In this work, morphology of P3BT at different crystalline polymorphs and solvent/thermal induced phase transition between form I and U modifications have been intensively investigated by using optical microscopy, electron microscopy, differential scanning calorimetry, and X-ray diffraction. It is shown that a direct deposition from carbon disulfide (CS2) at fast evaporation results in P3BT crystals in form I modification, giving typical whiskerlike morphology. In contrast, low evaporation rate from CS, leads to formation of form II crystals with spherulitic morphology, which is so far scarcely observed in polythiophene.

Single mode and multimodes lasing emission from MEH-PPV doped polystyrene thin films with surface ripples formed by vapour-induced phase separation

We report single mode and multimodes lasing emission from conjugated polymer poly[2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV) doped polystyrene ( PS) thin films with surface ripples. Surface ripples were formed by water vapour-induced phase separation. A single mode lasing emission at 606 nm with a line-width of less than 0.4 nm was obtained. The laser threshold was as low as 3.5 mu J pulse(-1). The side mode suppression ratio was 5.76 dB. The periodic changes of the refraction index in the MEH-PPV : PS blending film due to the phase separation should be attributed to the lasing actions.

Synthesis and Application of Thiadiazoloquinoxaline-Containing Chromophores as Dopants for Efficient Near-Infrared Organic Light-Emitting Diodes

series of a donor-acceptor-donor type of near-infrared (NIR) fluorescent chromophores based on [1,2,5]thiadiazolo[3,4-g]quinoxaline (TQ) as an electron acceptor and triphenylamine as an electron donor are synthesized and characterized. By introducing pendent phenyl groups or changing the pi-conjugation length in the TQ core, we tuned tile energy levels of these chromophores, resulting in the NIR emission in a range from 784 to 868 nm. High thermal stability and glass transition temperatures allow these chromophores to be used as dopant emitters, which can be processed by vapor deposition for the fabrication of organic light-emitting diodes (OLEDs) having the multilayered structure of ITO/MoO3/NPB/Alq(3):dopant emitter/BCP/Alq(3)/LiF/Al. The electroluminescence spectra of the devices based on these new chromophores cover a range from 748 to 870 nm. With 2 wt % of dopant 1, the LED device shows an exclusive NIR emission at 752 nm with the external quantum efficiency (EQE) as high as 1.12% over a wide range of current density (e.g., around 200 mA cm(-2)).

Novel blue light-emitting PPV-based copolymer containing triazole and carbazole units

A novel alternating conjugated copolymer containing triazole and carbazole units was synthesized by the Wittig reaction. The resulting bipolar conjugated polymer emits a pure light with good thermal stability, which is a promising candidate for polymer light emitting display.

Lasing behavior in DCM-doped PVK microcavity

A surface emitting microcavity was formed by sandwiching a polymer film containing PVK, Alq(3) and DCM between a distributed Bragg reflector (DBR) with a reflectivity of 99% and a silver film (300 nm). The lasing phenomenon was observed in DCM-doped PVK microcavity. The full width at half maximum (FWHM) was 0.6 nm with the peak wavelength at 603 nm. The threshold energy for lasing was estimated to be about 2.5 mu J per pulse. (C) 2000 Published by Elsevier Science S.A. All rights reserved.

Stimulated emission in the blue wavelength region from a copolymer containing PPV segment

The lasing properties of a soluble conjugated polymer, Poly[1,8-octanedioxy-2,6-dimethoxy-1,4-phenylene-1,2-ethenylene-1,2-phenylene-1,2-ethenylene-3,5-dimethoxy-1,4-phenylene] (CNMBC-Ph) in chloroform solution were investigated. The third harmonic radiation of a Nd:YAG laser was used as the pump light. The stimulated emission with a linewidth of 15 nm was observed in the blue wavelength region with the peak at 450 nm. The threshold pulse peak power was about 2.8 MW/cm(2). The energy conversion yield of the laser was estimated to be about 3.4%. The maximum peak power of the laser output pulse reached 40 kW. (C) 2000 Published by Elsevier Science S.A. All rights reserved.

Photoluminescent properties of dye-doped poly(N-vinyleabzole) (PVK) in microcavity

A surface emitting microcavity was formed by sandwiching a polymer film containing poly(N-vinyleabzole) (PVK). 8-hydroxyquinoline aluminium (Alq(3)) and 4-(Dicyanome thylene)-2-methyl-6-(4-dimethylaminostyryl)-4H-Pyran(DCM) between a distributed Bragg reflector (DBR) with a reflectivity of 99% and a silver film. The sample was optically pumped with 250 ps pulses at 2 Hz repetition rate by a 355 nm line of the third harmonic of a mode-lock Nd:YAG laser. The lasing phenomenon was observed in DCM-doped PVK microcavity. The full width at half maximum (FWHM) was 3 nm with the peak wavelength at 602 nm. The threshold energy for lasing was estimated to be about 3 mu J. (C) 2000 Elsevier Science S.A. All rights reserved.

Synthesis and characterization of aromatic dianhydrides and polyesterimides derived from 4-hydroxyphthalic anhydride

4-Hydroxyphthalic anhydride, prepared from 4-chlorophthalic anhydride, was reacted with trimellitic anhydride monoacid chloride or arylene diacid chloride to give aromatic ester-containing dianhydrides (EDAs). These dianhydrides were characterized by element analysis, melt point, FTIR and H-1-NMR. A series of aromatic poly (amic ester acid)s was synthesized by polycondensation of these EDAs and various diamines in polar organic solvent. The inherent viscosity of poly (amic ester acid)s ranged from 0.55 to 0.89 dL/g, indicating the intermediate to higher molecular weight. Polyesterimides having glass transition temperatures between 184-219degreesC were produced by thermal imidization of corresponding poly (amic ester acid)s. These polymers were fairly resistant to organic solvent, but some of them were soluble in phenol solvents. Thermogravimetric analyses revealed that these polyesterimides were stable up to 400degreesC, and the 5% weight loss temperatures were recorded in the range of 432-483degreesC in air atmosphers and 451-490degreesC in nitrogen.