Size distributions of quantum islands on stepped substrates

The size distributions of self-assembled quantum islands on stepped substrates are studied using kinetic Monte Carlo simulations. It is found that the energy barrier E-SW between the step and the terrace region is the key factor in affecting the size distribution of islands. With small E-SW (<= 0.1 eV), lines of uniform islands can be obtained at relative low surface coverage. As the surface coverage is increased, wirelike islands can be obtained. Scaling behavior is obeyed for the size distributions of the wirelike islands. When the size distributions are separated into their width and length components, however, scaling is only observed in the length distribution of the wirelike islands. With larger E-SW, the size distribution of islands shows a clear bimodal size distribution and anomalous growth temperature dependent island size evolutions are observed. The simulation results reproduce qualitatively the phenomena observed in the cases of InAs islands grown on stepped GaAs substrates. (c) 2009 American Institute of Physics. [doi:10.1063/1.3248367]

Realization of highly uniform self-assembled InAs quantum wires by the strain compensating technique

Self-assembled InAs quantum wires (QWRs) on InP(001) substrate have been grown by molecular-beam epitaxy, using a strain compensating technique. Atom force microscope, Transmission electron microscopy, and high-resolution x-ray diffraction are used to characterize their structural properties. We proposed that, by carefully adjusting composition of InAlGaAs buffer layer and strain compensating spacer layers, stacked QWRs with high uniformity could be achieved. In addition, the formation mechanism and vertical anti-correlation of QWRs are also discussed. (c) 2005 American Institute of Physics.

Comparison between gradient-doping GaAs photocathode and uniform-doping GaAs photocathode

We compared two reflection-mode negative electron affinity (NEA) GaAs photocathode samples that are grown by molecular beam epitaxy with p-type beryllium doping. One sample is uniform doping, and another is gradient doping. Experimental curves of spectral response sensitivity and quantum efficiency are obtained. The thicknesses of the two cathodes are both 2.6 mu m. The integrated sensitivity of the uniform doping one is 1966 mu A/lm, and that of the gradient-doping one is 2421 mu A/lm. The escape probability and diffusion length are fitted from the spectral response curves. For the uniform-doping sample, the escape probability is 0.45 and the diffusion length is 5 mu m. For the gradient-doping sample, the escape probability is 0.55 and the diffusion length is 5.5 mu m. (c) 2007 Optical Society of America.

Coherent tunnelling in coupled quantum wells under a uniform magnetic fields

Coherent tunnelling is studied in framework of the effective mass approximation for an asymmetric coupled quantum well. The Hartree potential due to the electron-electron interaction is considered in our calculation. The effects of the longitudinal and transverse magnetic field on coherent tunnelling characteristics are discussed. It has been found that the external field plays an important role in modulating the electron states.

Effects of rapid thermal annealing on the emission properties of highly uniform self-assembled InAs/GaAs quantum dots emitting at 1.3 mu m

The authors report the effects of rapid thermal annealing (RTA) on the emission properties of highly uniform self-assembled InAs quantum dots (QDs) emitting at 1.3 mu m grown on GaAs substrate by metal organic chemical vapor deposition. Postgrowth RTA experiments were performed under N-2 flow at temperatures ranging from 600 to 900 degrees C for 30 s using GaAs proximity capping. Surprisingly, in spite of the capping, large blueshifts in the emission peak (up to about 380 meV at 850 degrees C) were observed (even at low annealing temperatures) along with enhanced integrated photoluminescence (PL) intensities. Moreover, pronounced peak broadenings occurred at low annealing temperatures (< 700 degrees C), indicating that RTA does not always cause peak narrowing, as is typically observed with traditional QDs with large inhomogeneous PL linewidths. The mechanism behind the large peak blueshift was studied and found to be attributed to the as-grown QDs with large size, which cause a larger dot-barrier interface and greater strain in and near the QD regions, thereby greatly promoting Ga-In intermixing across the interface during RTA. The results reported here demonstrate that it is possible to significantly shift the emission peak of the QDs by RTA without any additional procedures, even at lower annealing temperatures. (c) 2007 American Institute of Physics.

Indium composition dependence of the size uniformity of InGaAs quantum dots on (311)B GaAs grown by molecular beam epitaxy

The deposition of InxGa1-xAs (0.2 less than or equal to x less than or equal to 0.5) on (311)B GaAs surfaces using solid source molecular beam epitaxy (MBE) has been studied. Both AFM and photoluminescence emission showed that homogeneous quantum dots could be formed on (311)B GaAs surface when indium composition was around 0.4. Indium composition had a strong influence on the size uniformity and the lateral alignment of quantum dots. Compared with other surface orientation, (100) and (n11) A/B (n=1,2,3), photoluminescence measurement confirmed that (311)B surface is the most advantageous in fabricating uniform and dense quantum dots.

New method for the growth of highly uniform quantum dots

A new method is realized for the growth of self-formed quantum dots. We identify that dislocation-free islands can be formed by the strain from the strained superlattice taken as a whole. Unlike the Stranski-Krastanow (S-K) growth mode, the islands do not form during the growth of the corresponding strained single layers. Highly uniform quantum dots can be self-formed via this mechanism. The low temperature spectra of self-formed InGaAs/GaAs quantum dot superlattices grown on a (001) GaAs substrate have a full width at half maximum of 26-34 meV, indicating a better uniformity of quantum dot size than those grown in the S-K mode. This method can provide great degrees of freedom in designing possible quantum dot devices. 1998 Published by Elsevier Science B.V. All rights reserved.

Uniform mems chip temperatures in the nucleate boiling heat transfer region by selecting suitable, medium boiling number range

The not only lower but also uniform MEMS chip temperatures can he reached by selecting suitable boiling number range that ensures the nucleate boiling heat transfer. In this article, boiling heat transfer experiments in 10 silicon triangular microchannels with the hydraulic diameter of 55.4 mu m were performed using acetone as the working fluid, having the inlet liquid temperatures of 24-40 degrees C, mass fluxes of 96-360 kg/m(2)s, heat fluxes of 140-420 kW/m(2), and exit vapor mass qualities of 0.28-0.70. The above data range correspond to the boiling number from 1.574 x 10(-3) to 3.219 x 10(-3) and ensure the perfect nucleate boiling heat transfer region, providing a very uniform chip temperature distribution in both streamline and transverse directions. The boiling heat transfer coefficients determined by the infrared radiator image system were found to he dependent on the heat Axes only, not dependent on the mass Axes and the vapor mass qualities covering the above data range. The high-speed flow visualization shows that the periodic flow patterns take place inside the microchannel in the time scale of milliseconds, consisting of liquid refilling stage, bubble nucleation, growth and coalescence stage, and transient liquid film evaporation stage in a full cycle. The paired or triplet bubble nucleation sites can occur in the microchannel corners anywhere along the flow direction, accounting for the nucleate boiling heat transfer mode. The periodic boiling process is similar to a series of bubble nucleation, growth, and departure followed by the liquid refilling in a single cavity for the pool boiling situation. The chip temperature difference across the whole two-phase area is found to he small in a couple of degrees, providing a better thermal management scheme for the high heat flux electronic components. Chen's [11 widely accepted correlation for macrochannels and Bao et al.'s [21 correlation obtained in a copper capillary tube with the inside diameter of 1.95 mm using R11 and HCFC123 as working fluids can predict the present experimental data with accepted accuracy. Other correlations fail to predict the correct heat transfer coefficient trends. New heat transfer correlations are also recommended.