Extraction and stripping of ytterbium (III) from H2SO4 medium by Cyanex 923

The extraction and stripping of ytterbium (III) from sulfuric acid medium using Cyanex 923 in heptane solution was investigated. The effects of extractant concentration, pH and sulfate ion as well as stripping agents, acidity and temperature on the extraction and stripping were studied. The equilibrium constants and thermodynamic parameters, such as Delta H (10.76 kJ(.)mol(-1)), Delta G (-79.26 kJ(.)mol(-1)) and Delta S (292.41 J(.)K(-1.)mol(-1)), were calculated. The extraction mechanism and the complex species extracted were determined by slope analysis and FrIR spectra. Furthermore, it was found that the extraction of Yb (III) from sulfuric acid medium by Cyanex 923 increased with pH, concentration of SO42-, HSO4-, and extractant concentration, and approximately a quantitative extraction of Yb (III) was achieved at an equilibrium pH near 3.0, and the extracted complex was YbSO4(HSO4)(.)2Cyanex923((o)).

Solvent extraction of scandium(III), yttrium(III), lanthanides(III), and divalent metal ions with sec-nonylphenoxy acetic acid

Such physicochemical properties of sec-nonylphenoxy acetic acid (CA-100) as the solubility in water, acid dissociation constant in water, dimerization constant in heptane, and distribution constant in organic solvent-water were measured by two-phase titration. The extraction behaviors of scandium (III), yttrium (III), lanthanides (III), and divalent metal ions from hydrochloric acid solutions with CA-100 in heptane have been investigated, and the possibilities of separating scandium (yttrium) from lanthanides and divalent metal ions have been carefully discussed. The stoichiometries of the extracted metal complexes were investigated by the slope-analysis technique. The effect of the nature of diluent on the extraction of yttrium (III) with CA100 has been studied and correlated with the dielectric constant.

Separation of heavy rare earth elements with extraction resin containing 1-hexyl-4-ethyloctyl isopropylphosphonic acid

This paper presents the results of the adsorption of heavy rare earth ions (Gd(III), Tb(III), Dy(III), Ho(III), Er(III), Tm(III), Yb(III), Lu(III) and Y(III)) from hydrochloric acid solutions at 30 degreesC by the extraction resin containing 1-hexyl-4-ethyloctyl isopropylphosphonic acid (HEOPPA), which has higher steric hindrance, higher selectivities and lower extraction and stripping acidity than di(2-ethylhexyl)phosphoric acid (DERPA) or 2-ethylhexyl phosphonic acid mono-2-ethylhexyl ester (HEH/EHP). The dependence of acid concentration, flow rate and amounts of rare earth ions sorbed on the separation of Er-Tm, Tm-Yb and Er-Tm-Yb mixtures has been studied. The baseline chromatographic separation of Er-Tm-Yb mixture has been observed. Satisfactory results with purity and yield of Tm2O3>99.71% and >71.25%, Er2O3>99-81% and >94.17%, and Yb2O3>99.74% and >89.83%, respectively, have been obtained. The parameters such,as resolution, separation factors and efficiencies have been determined as a function of acidity, loading of rare earth elements and flow rates. The stoichiometry of the extraction of rare earth ions has been suggested as well.

Extraction and separation of heavy rare earth (III) with Extraction Resin containing di(2,4,4-trimethyl pentyl) phosphinic acid (Cyanex 272)

Extraction resins, of the type of;levextrel, (which is a collective term for styrene/divinylbenzene based copolymers of predominantly macroporous structure that contain a selective extractant) are important for the recovery and separation of metal ions, as they combine features of solvent extraction and ion exchange resins. This paper presents the results of the adsorption of heavy rare earth ions (Ho(III), Er(III), Tm(III), Yb(III), Lu(III) and Y(III)) from hydrochloric acid solutions at 0.2 mol/L ionic strength and 50 degrees C by the extraction resin containing di (2,4,4-trimethyl pentyl) phosphinic acid (Cyanex 272) and the chromatographic separation of (Er(III), Tm(III) and Yb(III)). Technological separation products, with purity and yield of Tm2O3 >99.97%, >80%, Er2O3 >99.9%, >94% and Yb2O3 >99.8%, >80% respectively, have been obtained from a feed having the composition Tm2O3 60%, Er2O3 10%, and Yb2O3 3%, the others 27%. The distribution coefficients, extraction equilibrium constants and separation factors have been determined as a function of acidity, loading of the resin and rare earths, flow rates and column ratios. The resolutions and efficiencies of separation of Er/Tm/Yb each other have been calculated. The stoichiometry of the extraction of rare earth ions has been suggested as well.

Electrocatalytic reduction of nitrite using Dawson-type tungstodiphosphate anions in aqueous solutions, adsorbed on a glassy carbon electrode and doped in polypyrrole film

The electrochemical behavior of Dawson-type P2W18O626- adsorbed on a glassy carbon electrode and doped in a polypyrrole film electrode was described. These modified electrodes all display catalytic activity for nitrite reduction, either in acid solutions or in pH > 4.0 solutions.

Heterogenization of heteropolyacids: A general discussion on the preparation of supported acid catalysts

Heteropolyacids (HPAs) possess both acidic and redox catalytic properties and held extensive promise of practical application. These type of compound display a great potential of specific synthesis reactions for replacing sulfuric acid to satisfy the requirements of environmental protection. Heterogenizing HPAs would not only make them more useful in liquid phase oxidation with oxygen and in acid-catalyzed reaction, as the catalyst is often difficult to separate from the reaction products, but also create favorable factors for realizing heterogenization of homogeneous reaction and even utilizing new technology of catalytic distillation. In this paper, different kinds of porous materials which are well characterized, including oxides such as Al2O3, SiO2, TiO2, diatomite, bentonite, and active carbon of different sources, were used as support for heterogenizing HPAs (in different media), and the obtained results, the intrinsic characters of supports which may influence both the nature of the interaction between HPAs and supports in the heterogenization and the activity in the catalytic reaction, are explored. It is expected that these can provide a referential model for preparing supported acid catalyst used in liquid phase.

Scanning tunneling microscopy characterization of electrode materials in electrochemistry

Ex situ and in situ STM characterization of the electrode materials, including HOPG, GC, Au, Pt and other electrodes, is briefly surveyed and critically evaluated. The relationship between the electrode activity and surface microtopography is discussed.

SOLVENT-EXTRACTION OF SC(III), ZR(IV), TH(IV), FE(III), AND LU(III) WITH THIOSUBSTITUTED ORGANOPHOSPHINIC ACID EXTRACTANTS

The solvent extraction of Sc(III), Zr(IV), Th(IV), Fe(III) and Lu(III) with Cyanex 302 (bis(2,4,4-trimethylpentyl)monothiophosphinic acid) and Cyanex 301 ( bis(2,4,4-trimethylpentyl) dithiophosphinic acid) in n-hexane from acidic aqueous solutions has been investigated systematically. The effect of equilibrium aqueous acidity on the extraction with these reagents was studied. The separation of Th(IV), Fe(III) and Lu(III) from Sc(III), or the separation of other metals from Lu(III) with Cyanex 302, can be achieved by controlling the aqueous acidity. However, Cyanex 301 exhibited a poor selectivity for the above metals, except for Lu(III). The extraction of these metals with Cyanex 272, Cyanex 302 and Cyanex 301 has been compared. The stripping percentages of Sc(III) for Cyanex 302 and Cyanex 301 in a single stage are near 78% and 75% with 3.5 mol/L and 5.8 mol/L sulphuric acid solutions, respectively. The effects of extractant concentration and temperature on the extraction of Sc(III) were investigated. The stoichiometry of the extraction of Sc(III) with Cyanex 302 was determined. The role of different components of Cyanex 302 in the extraction of Sc(III) was discussed.

The effect of some triazole derivatives as inhibitors for the corrosion of mild steel in 1 M hydrochloric acid

Corrosion inhibition by some new triazole derivatives on mild steel in 1 M hydrochloric acid solutions has been investigated by weight loss test, electrochemical measurement, scanning electronic microscope analysis and quantum chemical calculations. The results indicate that these compounds act as mixed-type inhibitors retarding the anodic and cathodic corrosion reactions and do not change the mechanism of either hydrogen evolution reaction or mild steel dissolution. The studied compounds following the Langmuir adsorption isotherm, and the thermodynamic parameters were determined and discussed. The effect of molecular structure on the inhibition efficiency has been investigated by ab initio quantum chemical calculations. The electronic properties such as highest occupied molecular orbital (HOMO), lowest unoccupied molecular orbital (LUMO) energy levels, energy gap (LUMO-HOMO), dipole moment and molecular orbital densities were calculated. (C) 2009 Published by Elsevier B.V.

Preparation and optical properties of Ag/PPy composite colloids

Ag/PPy (polypyrrole) composite colloids were prepared through the reaction of silver nitrate with pyrrole solution in DNIF either in the dark, or under the irradiation of femtosecond laser (fs) pulse or UV lamp. The UV-vis spectra of the nanocomposite colloid display an intense absorption band around 620 nm, accompanied by a weak one around 470 nm. The colors and optical absorption spectra of as-synthesized colloids can be reversibly tuned between blue and red, corresponding to absorption band of 620 urn and 526 urn, within few seconds by adding base and acid solutions or gases in turn into the composite colloid suspension. In addition, excess of H+ solution enhanced the absorption band around 470 nm and, at the same time, depressed that around 620 nm. The possible mechanism for the formation and optical absorption properties of the Ag/PPy composite colloid was proposed. (C) 2006 Elsevier B.V. All rights reserved.

Production of biodiesel from soapstock using an ion-exchange resin catalyst

The feasibility of biodiesel production from soapstock containing high water content and fatty matters by a solid acid catalyst was investigated. Soapstock was converted to high-acid acid oil (HAAO) by the hydrolysis by KOH and the acidulation by sulfuric acid. The acid value of soapstock-HAAO increased to 199.1 mg KOH/g but a large amount of potassium sulfate was produced. To resolve the formation of potassium sulfate, acid oil was extracted from soapstock and was converted to HAAO by using sodium dodecyl benzene sulfonate (SDBS). The maximum acid value of acid oil-HAAO was 194.2 mg KOH/g when the mass ratio of acid oil, sulfuric acid, and water was 10:4:10 at 2% of SDBS. In the esterification of HAAO using Amberylst-15, fatty acid methyl ester (FAME) concentration was 91.7 and 81.3% for soapstock and acid oil, respectively. After the distillation, FAME concentration became 98.1% and 96.7% for soapstock and acid oil. The distillation process decreased the total glycerin and the acid value of FAME produced a little.

Novel biodiesel production technology from soybean soapstock

This paper describes an attractive method to make biodiesel from soybean soapstock (SS). A novel recovery technology of acid oil (AO) from SS has been developed with only sulfuric acid solution under the ambient temperature (25 +/- 2 degrees C). After drying, AO contained 50.0% FFA, 15.5% TAG 6.9% DAG 3.1% MAG 0.8% water and other inert materials. The recovery yield of AO was about 97% (w/w) based on the total fatty acids of the SS. The acid oil could be directly converted into biodiesel at 95 degrees C in a pressurized reactor within 5 hours. Optimal esterification conditions were determined to be a weight ratio of 1 : 1.5 : 0.1 of AO/methanol/sulfuric acid. Higher reaction temperature helps to shorten the reaction time and requires less catalyst and methanol. Ester content of the biodiesel derived from AO through one-step acid catalyzed reaction is around 92%. After distillation, the purity of the biodiesel produced from AO is 97.6% which meets the Biodiesel Specification of Korea. The yield of purified biodiesel was 94% (w/w) based on the total fatty acids of the soapstock.

Fluorescence Hydrogen Peroxide Probe Based on a Microstructured Polymer Optical Fiber Modified with a Titanium Dioxide Film

A highly sensitive microstructured polymer optical fiber (MPOF) probe for hydrogen peroxide was made by forming a rhodamine 6G-doped titanium dioxide film on the side walls of array holes in an MPOF. It was found that hydrogen peroxide only has a response to the MPOF probe in a certain concentration of potassium iodide in sulfuric acid solution. The calibration graph of fluorescence intensity versus hydrogen peroxide concentration is linear in the range of 1.6 x 10(-7) mol/L to 9.6 x 10(-5) mol/L. The method, with high sensitivity and a wide linear range, has been applied to the determination of trace amounts of hydrogen peroxide in a few real samples, such as rain water and contact lens disinfectant, with satisfactory results.

Cellulose acetate polymer film modified microstructured polymer optical fiber towards a nitrite optical probe

A novel microstructured polymer optical fiber (MPOF) probe for nitrites (NO(2)(-)) detection was made by forming rhodamine 6G (Rh 6G)-doped cellulose acetate (CA) on the side wall of array holes in a MPOF It was found that the MPOF probe only have a response to nitrites in a certain concentration of sulfuric acid solution The calibration graph of fluorescence intensity versus nitrites concentration was linear in the range of 2.0 x 10(-4) g/ml-5.0 x 10(-3) g/ml. The method possesses case of chemical modification, low cost design, and potential for direct integration with existing instrumentation, and has been applied to the determination of nitrites in real samples with satisfactory results. (C) 2010 Elsevier B.V. All rights reserved

川牛膝多糖的免疫活性及其水解活性片段分离研究

川牛膝多糖（CP）是从传统中药川牛膝（Cyathula officinalis Kuan）中提取的一种活性多糖，现代药理研究表明川牛膝多糖是川牛膝许多生物活性的物质基础。本实验室前期进行了川牛膝多糖的提取、分离、结构鉴定及其部分活性研究，发现川牛膝中多糖含量非常高，在对川牛膝多糖活性的初步研究中也证实了其具有免疫调节作用。我们为了进一步了解其免疫调节活性，并为构效关系的研究奠定基础，对其进行了如下研究： 1． 通过体外毒性检测、淋巴细胞增殖实验、NK细胞杀伤活性和腹腔巨噬细胞吞噬中性红活性测定，发现川牛膝多糖在10～300μg/mL浓度范围内，对细胞无毒性作用；能够促进LPS诱导的B淋巴细胞增殖(P<0.01)、增强NK细胞杀伤活性(P<0.05)和PMΦ吞噬中性红活性(P<0.01)，且随多糖浓度增高而增强；但其对ConA诱导的T淋巴细胞的增殖无促进作用(P>0.05)。 2． 通过正常小鼠体内淋巴细胞转化实验、迟发型变态反应分析、抗体生成细胞检测、碳粒廓清检测、腹腔巨噬细胞吞噬鸡红细胞活性和NK细胞活性测定，发现川牛膝多糖在适应性免疫方面能够促进SRBC免疫小鼠体内的抗体生成细胞的生成（P<0.01）和增强DNFB诱导的DTH（P<0.05），但对ConA诱导的脾淋巴细胞增殖无促进作用（P>0.05）；在固有免疫方面能够提高小鼠碳粒廓清速率（P<0.05），PMΦ吞噬 CRBC 活性（P<0.01）和NK细胞杀伤活性（P<0.05）。同时还发现其对由环磷酰胺(Cy)引起的白细胞数下降具有很好的抑制作用（P<0.01）。 3． 为了获得结构明确、均一的保留活性的川牛膝多糖片段，为其作用机制、构效关系研究提供关键研究材料，我们开展了“保留免疫活性的最小片段”的分离制备的初步研究。建立并优化了川牛膝多糖的酸水解条件，发现在6%的样品浓度，0.025mol/L的硫酸浓度，65℃的水解温度，水解时间为8min的条件下可以得到一系列连续的多糖片段；采用Bio-Gel P2 分子筛柱层析分离得到5个级分，通过体外淋巴细胞增殖实验、NK细胞活性测定、腹腔巨噬细胞吞噬中性红实验发现其中的一个片段仍保留较强的免疫活性，并测得其分子量约为2057Da，为保留免疫活性的最小片段的进一步分离奠定了基础。 Cyathula officinalis Kuan is a commonly-used Traditional Chinese Medicine (TCM) with a wide range of pharmacological activities. Modern pharmacological researches showed the polysaccharide extracted from it (CP) is an important component for many bioactivities of this TCM. In the previous studies, we found CP showed significant immuno-regulative activities. In order to evaluate this activity systematically and lay foundations for revealling its immuno-regulative machanisms and the Structure -Function relationship, we carried out the following research works: 1． The in vitro immunoactivities of CP were evaluated by using normal mice immunocytes with respects to cytotoxicity, lymphocytes proliferation, NK activity and the ability of peritoneal macrophage phagocytizing neutral red. The polysaccharide showed no cytotoxicity below the concentration of 300 μg/mL, and could promote B lymphocytes proliferation (P<0.01), enhance NK activity (P<0.05) and the ability of peritoneal macrophage phagocytizing neutral red (P<0.01) at the concentration of 10-300 μg/mL. The above effects were positively correlated with the concentration of the polysaccharides. But it could not promote T lymphocytes proliferation (P>0.05). 2． The in vivo immunoactivities of CP were observed on normal mice through the following indices: splenic lymphocyte transformation efficiency, delayed-type allergy, antibody-forming cells activity (AFC), rate of carbon clearance, rate of peritoneal macrophage phagocytizing chicken red blood cell (CRBC) and NK activity, and its influence on the decline of the mouse leucocyte count induced by Cy. The polysaccharide at medium-dose enhanced delayed-type allergy （P<0.05）and NK activity（P<0.05） and increased the rate of carbon clearance（P<0.05）, AFC activity（P<0.01） and the rate of peritoneal macrophage phagocytizing CRBC（P<0.01）. The polysaccharides also effectively resisted the decline of the mouse leucocyte count induced by Cy（P<0.01）. However, it couldn’t increase the splenic lymphocyte transformation efficiency（P>0.05）. 3． Attempting to isolate and prepare the minimal fragments retaining activity with identical structure for further studying on immuno-regulative mechanism and Structure-Function relationship, we carried out the study on hydrolysis of CP, isolation of hydrolysed fragments, and the activity evaluation of the isolated fragments. CP with concentration of 6% was hydrolysed at 65℃ for 8 min with sulfuric acid of 0.025 mol/L，then the hydrolysate was separated using Bio-Gel P2 chromatography, 5 portions of fragments were obtained. The immunoactivities of these fragments were evaluated by using normal mice immunocytes with respect to lymphocytes proliferation, NK activity and ability of peritoneal macrophage phagocytizing neutral red. One fragment with relative molecular mass of 2057Da was found retaining immunoactivity.