Synthesis and characterization of white-light-emitting polyfluorenes containing orange phosphorescent moieties in the side chain

Two orange phosphorescent iridium complex monomers, 9-hexyl-9-(iridium (III)bis(2-(4'-fluorophenyl)-4-phenylquinoline-N, C-2')(tetradecanedionate-11,13))-2,7-dibromofluorene (Br-PIr) and 9-hexyl-9-(iridium(III)bis(2-(4'-fluorophenyl)-4-methylquinoline-N, C-2')(tetradecanedionate-11,13))-2,7-dibromofluorene (Br-MIr), were successfully synthesized. The Suzuki polycondensation of 2,7-bis(trimethylene boronate)-9,9-dioctylfluorene with 2,7-dibromo-9,9-dioetylfluorene and Br-Plr or Br-MIr afforded two series of copolymers, PIrPFs and MIrPFs, in good yields, in which the concentrations of the phosphorescent moieties were kept small (0.5-3 mol % feed ratio) to realize incomplete energy transfer. The photoluminescence (PL) of the copolymers showed blue- and orange-emission peaks. A white-light-emitting diode with a configuration of indium tin oxide/poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)/PIr05PF (0.5 mol % feed ratio of Br-PIr)/Ca/Al exhibited a luminous efficiency of 4.49 cd/A and a power efficiency of 2.35 lm/W at 6.0 V with Commission Internationale de L'Eclairage (CIE) coordinates of (0.46, 0.33). The CIE coordinates were improved to (0.34, 0.33) when copolymer MIr10PF (1.0 mol % feed ratio of Br-MIr) was employed as the white-emissive layer. The strong orange emission in the electroluminescence spectra in comparison with PL for these kinds of polymers was attributed to the additional contribution of charge trapping in the phosphorescent dopants.

Copolymers derived from bismaleimide oligomer with active solvent

An oligomer from 4, 4'-bis(maleimido)diphenyl methane and methylenedianiline were dissolved in active solvent N,N-dimethyl acrylamide in a solid content up to 50-70%; the solution was poured in a sheet-shaped module and irradiated b y Co-60 with the dose from 20 to 350 kGy at room temperature. The polymerized sheet was postcured at 180degreesC to obtain a transparent red-orange sheet with tensile strength above 100 MPa. The glass transition temperature before and after postcuring was around 100degreesC and 150-180degreesC, respectively. Styrene was used along with DMAA to decrease the water absorption for the copolymers.

Morphology and structure of poly(di-n-butylsilane) single crystals prepared by controlling kinetic process of solvent evaporation

The silicon backbone conformation in poly(di-n-butylsilane) (PDBS) has been shown to be a 7/3 helix at ambient conditions, which is in marked contrast to the near-planar conformation of its homologous polymers with side chain lengths of one to three or six to eight carbon atoms. In this work, both the 7/3 helical and near-planar chain conformations are achieved by controlling the solvent evaporation rate around room temperature. The chain conformation and crystal structure obtained in this method have been correlated to the crystal morphology by wide-angle X-ray diffraction, transmission electron microscopy, electron diffraction, optical microscopy, atomic force microscopy, and UV absorption spectrum. The lath-shaped single crystals obtained at 12 degreesC correspond to an orthorhombic form with near-planar chain conformation whereas the lozenge-shaped single crystals obtained at 30 degreesC (in coexistence with the lath-shaped crystals) are orthohexagonal with a 7/3 helix.

White electrolumineseence from a single-polymer system with simultaneous two-color emission: Polyfluorene as the blue host and a 2,1,3-benzothiadiazole derivative as the orange dopant on the main chain

New single-polymer electroluminescent systems containing two individual emission species - polyfluorenes as a blue host and 2,1,3-benzothiadiazole derivative units as an orange dopant on the main chain - have been designed and synthesized. The resulting single polymers are found to have highly efficient white electroluminescence with simultaneous blue(lambda(max) = 421 nm/445 nm) and orange emission (lambda(max) = 564 nm)from the corresponding emitting species. The influence of the photoluminescence (PL) efficiencies of both the blue and orange species on the electroluminescence (EL) efficiencies of white polymer light-emitting diodes (PLEDs) based on the single-polymer systems has been investigated. The introduction of the highly efficient 4,7-bis(4-(N-phenyl-N-(4-methylphenyl)amino)phenyl)-2,1,3-benzothiadiazole unit to the main chain of polyfluorene provides significant improvement in EL efficiency. For a single-layer device fabricated in air (indium tin oxide/poly(3,4-ethylenedioxythiophene): poly(styrene sulfonic acid/polymer/Ca/Al), pure-white electroluminescence with Commission Internationale de l'Eclairage (CIE) coordinates of (0.35,0.32), maximum brightness of 12 300 cd m(-2), luminance efficiency of 7.30 cd A(-1), and power efficiency of 3.34 lm W-1 can be obtained.

Solvent-dependent formation of di- and trinuclear rhodiurn and iridium complexes bridged by N,N '-donor ligands

Reactions of Rh and Ir hydrido complexes. [Rh(H)(2)(PPh3)(2)(solv)(EtOH)]ClO4 (solv = Me2CO, 1a; EtOH, 1b) and [Ir(H)(2)(PPh3)(2)(Me2CO)(2)]BF4 (2), with various N,N'-donor bridging ligands, such as pyrazine (pyz), 4,4'-trimethylenedipyridine (tmdp) and di(4-pyridyl) disulfide (dpds), in some solvents were examined, and their reaction products were characterized by X-ray crystal structure analysis. IR, H-1 NMR and UV-vis spectra. Rh hydrido complexes, la or 1b, formed a dinuclear Rh complex, [Rh-2(PPh3)(2) {(eta(6)-C6H5PPh2}(2)] (ClO4)(2).6CH(2)Cl(2) (3.6CH(2)Cl(2)), in dichloromethane with a reductive elimination of hydrogen. The reactions of 1a or 1b with the pyz ligand in dichloromethane and tetrahydrofuran gave triangular Rh-3 complexes, [Rh-3(PPh3)(6)(pyz)(3)](ClO4)(3).CH2Cl2 (5.CH2Cl2) and [Rh-3(PPh3)(6)(pyz)(3)](ClO4)(3).EtOH (5.EtOH), respectively, in contrast to the formation of a dinuclear Rh hydrido complex, [Rh-2(H)(4)(PPh3)(4)(Me2CO)(2)(pyz)](ClO4)(2).EtOH A-EtOH). in acetone. The reactions of la or 1b with the tmdp ligand in dichloromethane and 3-methyl-2-butanone also afforded dinuclear Rh complexes, [Rh-2(PPh3)(4)(tmdp)(2)](ClO4)(2) (6) and [Rh-2(PPh3)(4)(tmdp)(2)](ClO4)(2).4MeCOCHMe(2) (6.4MeCOCHMe(2)), respectively. On the other hand, Ir hydrido complex 2 reacted with pyz and dpds ligands in dichloromethane to afford dinuclear Ir complexes, [Ir-2(H)(4)(PPh3)(4)(Me2CO)(2)(pyz)]- (BF4)(2).3CH(2)Cl(2) (7.3CH(2)Cl(2)) and [Ir-2(H)(4)(PPh3)(4)(dpds)(2)](BF4)(2).3CH(2)Cl(2).H2O (8.3CH(2)Cl(2).H2O), respectively, without any reductive elimination of hydrogen. Based on structural studies in solution and in the solid state. it was demonstrated that various Rh and Ir complexes were selectively produced depending on the choice of solvents and N,N'-donor bridging ligands.

Microelectrode voltammetric measurement of heterogeneous electron transfer rate constants for reduction of 7,7,8 ',8 '-tetracyanoquinodimethane in polymer electrolytes

This paper presents a microelectrode voltammetric determination of heterogeneous electron transfer rate constants (k(s)) and diffusion coefficients (D) of 7,7,8',8 '-tetracyanoquinodimethane (TCNQ) in polyelectrolytes. The diffusion coefficients are estimated using cyclic voltammetry under linear diffusion conditions, and the heterogeneous electron transfer rate constants are obtained under mixed linear and radial diffusion in the polyelectrolyte. k(s) and D increase with increasing temperature, and the activation barriers of the electrode reaction for reduction of TCNQ are obtained. On the other hand, the dependencies of D and k(s) of TCNQ on the size and charge of the counterion are compared in the polyelectrolyte. (C) 1998 Elsevier Science Ltd. All rights reserved.

Synthesis and solvent enhanced relaxation property of water-soluble endohedral metallofullerenols

Gadolinium fullerenols, as novel and potential contrast agents for magnetic resonance imaging, were synthesized, which showed excellent efficiency in enhancing water proton relaxation with a relaxivity of 47.0+/-1.0 mM(-1).s(-1).

Study on the UCST and LCST in PHB/PBHE-solvent system

Upper and lower critical solution temperature (UCST and LCST) behaviours have been examined for solution of PHB/PBHE blends in chloroform and chlorobenzene. Polymer-Solvent systems prepared with various solvents and concentrations were found to possess UCST and LCST characteristics. PHB/PBHE solution in chloroform displayed greater miscibility temperature region than that of the blend in chlorobenzene, but the relative tendency of both UCST and LCST were similar.

WATER-SOLUBLE AND AMPHIPHILIC POLYMERS .7. SYNTHESIS AND CHARACTERIZATION OF A NOVEL COMB-TYPE AMPHIPHILIC POLYMER PAMC16S

A novel comb-like amphiphilic polymer, poly (2-acrylamidohexadecylsulfonic acid) (PAMC16S), was synthesized by free radical polymerization of the corresponding amphiphilic monomer in 1,4-dioxane-water mixed solvents. Depending on the ratio of water/dioxane in the solvent, the reaction proceeded by either precipitation polymerization or micellar polymerization. The molecular weight of the polymer obtained under similar conditions decreased and subsequently increased with the increase of water content in the mixed solvent. The polyion nature of PAMC16S was confirmed by viscosity data of ethanolic solutions. In addition, the polymer was characterized by solubility, IR, TG and wide angle X-ray diffraction methods.

Magnetron Sputtering Growth of InAs0.3Sb0.7 Films on (100) GaAs Substrates: Strong Effect of Growth Conditions on Film Structure

The growth of highly lattice-mismatched InAs0.3Sb0.7 films on (100) GaAs Substrates by magnetron Sputtering has been investigated and even epitaxial lnAs(0.3)Sb(0.7) films have been successfully obtained. A strong effect of the growth conditions on the film structure was observed, revealing that there was a growth mechanism transition from three-dimensional nucleation growth to epitaxial layer-by-layer growth mode when increasing the substrate temperature. A qualitative explanation for that transition was proposed and the critical conditions for the epitaxial layer-by-layer growth mode were also discussed.

对童氏"7.5B"计算及乙型水驱法的改进

研究了童宪章院士"7.5B"的准确性和适应性,指出了"7.5B"方法只适用于多个油田的统计计算,而不完全适应于单一油藏.从理论上推导了"7.5B"的数学表达式,给出了一条准确计算该值的有效途径.对童氏水油比与采出程度关系乙型水驱法及采出程度与含水关系图版作了改进.

Coherent Structures in Transition of a Flat-Plate Boundary Layer at Ma=0.7

Direct numerical simulation (DNS) of a spatially evolving flat-plate boundary layer transition process at free stream Mach number 0.7 is performed. Tollmien-Schlichting (T-S) waves are added on the inlet boundary as the disturbances before transition. Typical coherent structures in the transition process are investigated based on the second invariant of velocity gradient tensor. The instantaneous shear stress and the mean velocity profile in the transition region are studied. In our view, the fact that the peak value of shear stress in the stress concentration area increases and exceeds a threshold value during the later stage of the transition process plays an important role in the laminar breakdown process.

Comparative Study Of The Influence Of Natural Convection On Directional Solidification Of Al-3.5 Wt% Ni And Al-7 Wt% Si Alloys

We present numerical simulations of thermosolutal convection for directional solidification of Al-3.5 wt% Ni and Al-7 wt% Si. Numerical results predict that fragmentation of dendrite arms resulting from dissolution could be favored in Al-7 wt% Si, but not in Al-3.5 wt% Ni. Corresponding experiments are in qualitative agreement with the numerical predictions. Distinguishing the two fragmentation mechanisms, namely dissolution and remelting, is critical during experiments on earth, when fluid flow is dominant. (C) 2007 COSPAR. Published by Elsevier Ltd. All rights reserved.

InAs0.3Sb0.7 films grown on (100) GaSb substrates with a buffer layer by liquid-phase epitaxy

The growth of InAsxSb1-x films on (100) GaSb substrates by liquid-phase epitaxy (LPE) has been investigated and epitaxial InAs0.3Sb0.7 films with InAs0.9Sb0.09 buffer layers have been successfully obtained. The low X-ray rocking curve FHWM values of InAs0.3Sb0.7 layer shows the high quality of crystal-orientation structure. Hall measurements show that the highest electron mobility in the samples obtained is 2.9 x 10(4) cm(2) V-1 s(-1) and the carrier density is 2.78 x 10(16)cm(-3) at room temperature (RT). The In As0.3Sb0.7 films grown on (10 0) GaSb substrates exhibit excellent optical performance with a cut-off wavelength of 12 mu m. (c) 2007 Elsevier B.V. All rights reserved.

第7届国际等离子体化学会议(ISPC-7)

<正> Ⅰ.概况 国际等离子体化学会议(ISPC)每两年举行一次,主要交流等离子体化学如下几方面的研究和发展情况:合成,诊断,等离子体刻蚀,等离子体沉积和聚合,模型,表面作用以及熔化、气化、等离子体喷涂等。ISPC-7由荷兰Ejndhoven技术大学负责组织,Philips公司支持,在Philips会议中心举行。会议期1985年7月1—5日。第一天样品展览,