Steady state ion acceleration by a circularly polarized laser pulse

The steady state ion acceleration at the front of a cold solid target by a circularly polarized flat-top laser pulse is studied with one-dimensional particle-in-cell (PIC) simulation. A model that ions are reflected by a steady laser-driven piston is used by comparing with the electrostatic shock acceleration. A stable profile with a double-flat-top structure in phase space forms after ions enter the undisturbed region of the target with a constant velocity. (C) 2007 Elsevier B.V. All rights reserved.

Effect of plasma temperature on electrostatic shock generation and ion acceleration by laser

The effect of plasma temperature on electrostatic shock generated by a circularly polarized laser pulse in overdense plasma is studied by particle-in-cell simulation. Ion reflection and transmission in the collisionless electrostatic shock (CES) are investigated analytically. As the initial ion temperature is varied, a distinct transition from the laser-driven piston scenario with all ions being reflected to the CES scenario with partial ion reflection is found. The results show that at low but finite temperatures the ions are much more accelerated than if they were cold.

阵列光栅压缩器的空域特性

引入角度偏差、位移偏差作为拼接光栅系统的物理参数，定义了拼接光栅的孔径函数，利用傅里叶角谱理论研究了高斯脉冲入射拼接光栅压缩器后的远场分布特性。研究表明；出射脉冲仍然是高斯型脉冲，但包络中心发生偏移，偏移量由角度偏差量和光束口径决定；位移偏差引入的相位随着拼接光栅压缩器传递，其对远场焦斑的影响，取决于每片子光栅的非整数倍光栅常数的横向位移偏差和纵向位移偏差的综合作用。通过数值计算得到了各维偏差对阵列光栅压缩器空域特性的影响，计算表明：光栅面外角度偏差（俯仰左右）和条纹平行度偏差都必须控制在1μrad以内，

Fiber Bragg grating pressure sensor with enhanced sensitivity

A novel fiber Bragg grating (FBG) pressure sensor with the enhanced sensitivity has been demonstrated. A piston-like diaphragm with a hard core in the center is used to enhance the sensitivity. Both the theoretical analysis and the experimental result show that the radius of the hard core has significant effect on the pressure sensitivity. When the radius of the hard core is 1.5 mm, a pressure sensitivity of 7.23 nm/MPa has been achieved.

Ultrathin FBG pressure sensor with enhanced responsivity

An ultrathin fiber Bragg grating pressure sensor with enhanced sensitivity is demonstrated. A novel piston-like diaphragm with a hard core in the center is used as the sensing element to enhance the responsivity. Both the theoretical analysis and the experimental results show that the Young's modulus of the diaphragm and the radius of the hard core have significant effect on the pressure responsivity. By optimizing these two parameters, a pressure responsivity of 7 nm/MPa has been achieved.

Geomagnetic paleointensity dating of South China Sea sediments for the last 130 kyr

Relative paleointensity records from the northern South China Sea, northwest Pacific Ocean were studied in two gravity piston cores. Continuous mineral magnetic and paleomagnetic measurements were made using discrete sediment samples. Detailed rock magnetic parameters, such as thermomagnetic and high-field hysteresis data, indicate that pseudo-single domain magnetite in a narrow range of grain-size and concentration is the main contributor to the remanent magnetization. The uniform magnetic mineralogy meets the commonly accepted criteria for establishing relative paleointensity records. The relative paleointensity (RPI) curves were constructed by normalizing the natural remanent magnetization (NRM) with isothermal remanent magnetization (IRM), both in the 20-60 mT demagnetization state. Dating constraints have been provided by radiocarbon ages in the upper 400 cm of both cores. Furthermore, we have correlated our paleointensity records with NAPIS-75, S.Atlantic-1089, Sint-200 and NOPAPIS-250 to determine the chronological RPI framework for the South China Sea (SCS-PIS). Although some temporal offsets of paleointensity features between the different records have been recognized, their similar shape suggests that relative paleointensity on the 10(3)-10(4) year scale is globally coherent and can provide an age framework for sediments independent of delta O-18 ages.

Design and Operation of A 5.5 MWe Biomass Integrated Gasification Combined Cycle Demonstration Plant

The design and operation of a 5.5 MWe biomass integrated gasification combined cycle (IGCC) demonstration plant, which is located in Xinghua, Jiangsu Province of China, are introduced. It is the largest complete biomass gasification power plant that uses rice husk and other agricultural wastes as fuel in Asia. It mainly consists of a 20 MWt atmospheric circulating fluidized-bed gasifier, a gas-purifying system, 10 sets of 450 kW(e) gas engines, a waste heat boiler, a 1.5 MWe steam turbine, a wastewater treatment system, etc. The demonstration plant has been operating since the end of 2005, and its overall efficiency reaches 26-28%. Its capital cost is less than 1200 USD/kW, and its running cost is about 0.079 USD/kWh based on the biomass price of 35.7 USD/ton. There is a 20% increment on capital cost and 35% decrease on the fuel consumption compared to that of a 1 MW system without a combined cycle. Because only part of the project has been performed, many of the tests still remain and, accordingly, must be reported at a later opportunity.

Upgrading bio-oil over different solid catalysts

Solid acid 40SiO(2)/TiO2-SO42- and solid base 30K(2)CO(3)/Al2O3-NaOH were prepared and compared with catalytic esterification activity according to the model reaction. Upgrading bio-oil by solid acid and solid base catalysts in the conditioned experiment was investigated, in which dynamic viscosities of bio-oil was lowered markedly, although 8 months of aging did not show much viscosity to improve its fluidity and enhance its stability positively. Even the dehydration by 3A molecular sieve still kept the fluidity well. The density of upgraded bio-oil was reduced from 1.24 to 0.96 kg/m(3), and the gross calorific value increased by 50.7 and 51.8%, respectively. The acidity of upgraded bio-oil was alleviated by the solid base catalyst but intensified by the solid acid catalyst for its strong acidification. The results of gas chromatography-mass spectrometry analysis showed that the ester reaction in the bio-oil was promoted by both solid acid and solid base catalysts and that the solid acid catalyst converted volatile and nonvolatile organic acids into esters and raised their amount by 20-fold. Besides the catalytic esterification, the solid acid catalyst carried out the carbonyl addition of alcohol to acetals. Some components of bio-oil undertook the isomerization over the solid base catalyst.

脉冲爆轰发动机的系统性能分析

采用简化的脉冲爆轰推进装置模型, 利用热循环效率分析方法, 推导了包含进气道总压恢复系数的热循环效率公式, 并在特定来流条件下, 考察了一个爆轰循环中进气道总压恢复系数和燃烧室初始温度对热循环效率和比冲的影响, 研究发现, 降低来流总压损失有助于提高热循环效率, 而提高燃烧室初始温度能更有效地提高热循环效率, 据此, 提出了多级重起爆脉冲爆轰发动机概念, 利用在突扩截面上解耦的爆轰波的前导激波去再次压缩工质, 进一步提高工质的热力学参数, 从而提高脉冲爆轰装置的热循环效率, 推导了此种构型PDE的热循环效率计算公式, 并对多级重起爆脉冲爆轰发动机进行了原理性论证, 研究结果表明, 多级重起爆方法提高了燃烧室的爆前温度, 从而有效地提高脉冲爆轰发动机热循环效率.最后, 关于出口工质的非完全膨胀的情况, 做了定性的阐述, 认为只有降低工质的出口压力, 才能更有效增加工质的出口动能, 从而提高热循环效率

冲压发动机尾喷管实验新方法

阐述冲压发动机尾喷管地面模拟实验的新方法.采用双爆轰技术产生稳定的高焓燃气模拟高马赫数飞行条件下冲压发动机的燃烧气体;利用皮托管测量尾喷管推力,并对测量误差进行了分析;为研究催化复合效应增大推力提供实验基础

Numerical simulation of thermal loading produced by shaped high power laser onto engine parts

Recently a new method for simulating the thermal loading on pistons of diesel engines was reported. The spatially shaped high power laser is employed as the heat source, and some preliminary experimental and numerical work was carried out. In this paper, a further effort was made to extend this simulation method to some other important engine parts such as cylinder heads. The incident Gaussian beam was transformed into concentric multi-circular patterns of specific intensity distributions, with the aid of diffractive optical elements (DOEs). By incorporating the appropriate repetitive laser pulses, the designed transient temperature fields and thermal loadings in the engine parts could be simulated. Thermal-structural numerical models for pistons and cylinder heads were built to predict the transient temperature and thermal stress. The models were also employed to find the optimal intensity distributions of the transformed laser beam that could produce the target transient temperature fields. Comparison of experimental and numerical results demonstrated that this systematic approach is effective in simulating the thermal loading on the engine parts. (C) 2009 Elsevier Ltd. All rights reserved.

CFD analysis of thermodynamic cycles in a pulse tube refrigerator

The objectives of this paper are to study the thermodynamic cycles in an inertance tube pulse tube refrigerator (ITPTR) by means of CFD method The simulation results show that gas parcels working in different parts of ITPTR undergo different thermodynamic cycles The net effects of those thermodynamic cycles are pumping heat from the low temperature part to the high temperature part of the system The simulation results also show that under different frequencies of piston movement the gas parcels working in the same part of the system will undergo the same type of thermodynamic cycles The simulated thermal cycles are compared with those thermodynamic analysis results from a reference Comparisons show that both CFD simulations and theoretical analysis predict the same type of thermal cycles at the same location However only CFD simulation can give the quantitative results while the thermodynamic analysis is still remaining in quality (C) 2010 Elsevier Ltd All rights reserved

Application of rare earths in thermal barrier coating materials

Rare earths are a series of minerals with special properties that make them essential for applications including miniaturized electronics, computer hard disks, display panels, missile guidance, pollution controlling catalysts, H-2-storage and other advanced materials. The use of thermal barrier coatings (TBCs) has the potential to extend the working temperature and the life of a gas turbine by providing a layer of thermal insulation between the metallic substrate and the hot gas. Yttria (Y2O3), as one of the most important rare earth oxides, has already been used in the typical TBC material YSZ (yttria stabilized zirconia). In the development of the TBC materials, especially in the latest ten years, rare earths have been found to be more and more important. All the new candidates of TBC materials contain a large quantity of rare earths, such as R2Zr2O7 (R=La, Ce, Nd, Gd), CeO2-YSZ, RMeAl11O19 (R=La, Nd; Me=Mg, Ca, Sr) and LaPO4. The concept of double-ceramic-layer coatings based on the rare earth materials and YSZ is effective for the improvement of the thermal shock life of TBCs at high temperature.

Ceramic materials for thermal barrier coatings

This paper summarizes the basic properties of ceramic materials for thermal barrier coatings. Ceramics, in contrast to metals, are often more resistant to oxidation, corrosion and wear, as well as being better thermal insulators. Except yttria stabilized zirconia, other materials such as lanthanum zirconate and rare earth oxides are also promising materials for thermal barrier coatings.

Methane-derived authigenic carbonates from the Ulleung basin sediments, East Sea of Korea

Authigenic carbonates were sampled in methane-enriched piston core sediments collected from gas venting sites on the western continental slope of the Ulleung Basin, East Sea of Korea. Multidisciplinary investigations on these carbonates, including the scanning electronic microscope (SEM) observations and mineralogical-geochemical compositions, were carried out to identify the carbon and oxygen sources and the forming mechanism of these carbonates. The authigenic carbonates from the study area correspond to semi-consolidated, compact concretions or nodules ranging from 2 to 9 cm in size. X-ray diffraction and electron microprobe analyses showed that most of the sampled carbonate concretions were composed of almost purely authigenic high-Mg calcite (10.7-14.3 mol% MgCO3). Characteristically, microbial structures such as filaments and rods, which were probably associated with the authigenic minerals, were abundantly observed within the carbonate matrix. The carbonates were strongly depleted in delta C-13 (-33.85 parts per thousand to -39.53 parts per thousand Peedee Belemnite (PDB)) and were enriched in delta O-18 (5.16-5.60 parts per thousand PDB), indicating that the primary source of carbon is mainly derived from the anaerobic oxidation of methane. Such methane probably originated from the destabilization of the underlying gas hydrates as strongly supporting from the enriched O-18 levels. Furthermore, the strongly depleted delta C-13 values (-60.7 parts per thousand to -61.6 parts per thousand PDB) of the sediment void gases demonstrate that the majority of the gas venting at the Ulleung Basin is microbial methane by CO2 reduction. This study provides another example for the formation mechanism of methane-derived authigenic carbonates associated with gas-hydrate decomposition in gas-seeping pockmark environments. (c) 2009 Elsevier Ltd. All rights reserved.