Chemical characteristics of a polysaccharide from Porphyra capensis (Rhodophyta)

The structure of a polysaccharide from the red seaweed, Porphyra capensis, growing along the coast of Namibia and South Africa was investigated. Algae growing at different sites and collected at different times gave a polysaccharide extract with similar chemical components. FTIR and NMR spectral analysis showed that the polysaccharide from P. capensis had a typical porphyran structure. It has the linear backbone of alternating 3-linked beta-D-galactose and 4-linked alpha-L-galactose-6-sulfate or 3,6-anhydro-alpha- L-galactose units. The ratio of alpha-L-galactose-6-sulfate and the 3,6-anhydrogalactose is 121, as reflected by a H-1 NMR spectrum. A high degree of methylation occurred at the C-6 position of the D-galactose units. The degree of methylation was 0.64 for the D-galactose residues. (C) 2005 Elsevier Ltd. All rights reserved.

Influence of Surface Stress on Frequency of Microcantilever-Based Biosensors (vol 10, pg 307, 2004)

Microcantilever-based biosensors have been found increasing applications in physical, chemical, and biological fields in recent years. When biosensors are used in those fields, surface stress and mass variations due to bio-molecular binding can cause the microcantilever deform or the shift of frequency. These simple biosensors allow biologists to study surface biochemistry on a micro or nano scale and offer new opportunities in developing microscopic biomedical analysis with unique characteristics. To compare and illustrate the influence of the surface stress on the frequency and avoid unnecessary and complicated numerical solution of the resonance frequency, some dimensionless numbers are derived in this paper by making governing equations dimensionless. Meanwhile, in order to analyze the influence of the general surface stress on the frequency, a new model is put forward, and the frequency of the microcantilever is calculated by using the subspace iteration method and the Rayleigh method. The sensitivity of microcantilever is also discussed. (19 refs.)

土壤改良剂改土培肥增产效应研究综述

壤改良剂研究已是近年来国内外广泛关注的热点,在对土壤改良剂发展及其种类进行简要回顾的基础上,对土壤改良剂的改土培肥效应(物理结构、化学特性、生化特性)、作物增产效应及其施用技术进行了较为全面的分析和评述,并提出了目前存在的问题和展望了土壤改良剂的研究趋势。

Recent developments in intelligent biomedical polymers

Intelligent polymers or stimuli-responsive polymers may exhibit distinct transitions in physical-chemical properties, including conformation, polarity, phase structure and chemical composition in response to changes in environmental stimuli. Due to their unique 'intelligent' characteristics, stimuli-sensitive polymers have found a wide variety of applications in biomedical and nanotechnological fields. This review focuses on the recent developments in biomedical application of intelligent polymer systems, such as intelligent hydrogel systems, intelligent drug delivery systems and intelligent molecular recognition systems. Also, the possible future directions for the application of these intelligent polymer systems in the biomedical field are presented.

碳纳米管场效应晶体管的自动化装配方法研究

自碳纳米管(Carbon nanotube,CNT)被发明以来,研究者就对CNT所表现出来的优异的物理、化学以及电学特性产生了浓厚的兴趣。近年来,CNT基纳米器件的研究取得了重要进展。特别是利用半导体性CNT制造的碳纳米管场效应晶体管(Carbon nanotube field effect transistor,CNT-FET),在化学传感器以及生物传感器等领域表现出了巨大的应用潜力。为此,本文首先介绍了目前CNT-FET制造方法的研究现状。对基于介电泳(Dielectrophoresis,DEP)的CNT-FET制造方法进行了系统分析,构建了基于DEP方法可实现碳纳米管场效应晶体管的自动化装配的微滴定实验系统。本文进行的CNT-FET装配实验,证明了该系统的有效性。

长白山火山成因—物理机制和化学演化

This thesis is one of the contributions to NSFC project, “The Changbaishan Volcanism and its Links to the Northeast Asia Tectonic System”. The thesis presents our most recent works on Changbaishan Volcanism, on two aspects as (1) the chemical evolution of the Cenozoic volcanism and the physical links of magma genesis, (2) the Holocene activity of the Tianchi Volcano and risks of potential eruption. 1. Chemical evolution and physical links to the Changbaishan Volcanism Physical links to the Chanbaishan Volcanism, just like origins of most of the volcanisms in eastern China, has long been an enigma. A large scale of volcanic activity has dominated many places of eastern China in Meso-Cenozoic. Activity of these volcanisms in eastern China covers several quite different blocks, covers variety of tectonics, and covers a period of time over 200 million years. Such a large-scale and long-lived volcanism in a continental area challenges our knowledge on dynamics of the Earth’s interior. Some works on “Diwa” hypothesis and “lithospheric thinning” hypothesis present possible links between volcanisms and dynamic evolutions of the earth’s interior, but still cannot interpret where are the sources of the heat and fluid, which are essential to the volcanisms. Based on the study of this thesis, we suggest that dynamics of the deep subduction of western Pacific Plate is the critical factor to the Changbaishan Volcanism and volcanisms in NE China, and maybe even essential to most of the Meso-Cenozoic volcanisms in eastern China. In NE China, stagnant slabs flatted in the mantle transition zone (MTZ, ca. 660 km deep) transport and release significant hydrous fluid to the upper mantle. Metamorphism of the deep-subducted slabs and hence a series of mineral phases play an important role in the water transport, exchange, restore, and release. Dehydrated fluid of the wet slab ascending from the MTZ fertile the upper mantle, and also provide upward heat flow which is essential to the magma genesis. Then magma and volcanism occur with the deep subduction from Mesozoic to mordern time in eastern China. To discribe the exact chemical characteristics of the deep subduction releated volcanics is very difficult, because few researches has contributed to the chemical behaviors of fluid and trace elments in the very deep interior of the Earth, such 660 km deep, 410km or 350km where the fluid may ascend and react. However we can still find some chemical characteristics of oceanic subduction. Basalts of the Changbaishan Volcanism have siginficant characteristics of potassium rich, and even can be called a potassic igneous province. If there are only two possible ways, recycled continentical crust or oceanic crust, to fertile the mantle potossium element as we know now, it’s easy to attribute this to the deep-subducted of the west Pacific Plate. To the eastern China, fluid inclusions in mantle xenoliths from the Cenozic basalts also reveal potassium-rich characteristics. This reveals that the same potassium feritle agents may occur in the mantle sources of eastern China. 2. Holocene activiy of the Tianchi Volcano As one of the large volcanic center and complex volcanic cone, the Tianchi Volcano is a dangerous active volcano, with several Holocene eruptions. Among these eruptions, the Millennium Eruption is regardede as one of the biggist eruptions in the world in the last 2000 years. To estimate the potential danger of volcanic eruption, we discuss two essential factors, as (i) volcanic history of Holocene eruptions, including volcanic geolgy, chronnology and chemistry, (ii) state, evolution and relationship of the magma chambers in mantle and crust beneath the Tianchi Volcano.

东海陆架盆地西南部烟囱构造与油气运聚关系研究

In recent years, chimney structure has been proved one of important indicators and a useful guide to major petroleum fields exploration through their exploration history both at home and abroad. Chimney structure, which has been called "gas chimney" or "seismic chimney", is the special fluid-filled fracture swarm, which results from the boiling of active thermal fluid caused by abruptly decreasing of high pressure and high temperature in sedimentary layers of upper lithosphere. Chimney structure is well developed in continental shelf basin of East China Sea, which indicates the great perspectives of petroleum resources there. However, the chimney structure also complicated the petroleum accumulation. So the study of chimney structure on its formation, its effect on occurrence and distribution of petroleum fields is very important not only on theoretical, but also on its applied research. It is for the first time to make a clear definition of chimney structure in this paper, and the existence and practical meaning of chimney structure are illustrated. Firstly, on the viewpoint of exploration, this will amplify exploration area or field, not only in marine, but also on continent. Secondly, this is very important to step-by-step exploration and development of petroleum fields with overpressure. Thirdly, this will provide reference for the study on complex petroleum system with multi-sources, commingled sources and accumulation, multi-stage accumulations, and multi-suits petroleum system in the overlay basin. Fourthly, when the thermal fluid enters the oceanic shallow layer, it can help form gas hydrate under favorable low-temperature and high-pressure conditions. Meanwhile, the thermal fluid with its particular component and thermal content will affect the physical, chemical and ecological environments, which will help solving the problem of global resources and environment. Beginning from the regional tectonic evolution characteristics, this paper discussed the tectonic evolution history of the Taibei depression, then made an dynamical analysis of the tectonic-sedimentary evolution during the Mesozoic and Cenozoic for the East China Sea basin. A numerical model of the tectonic-thermal evolution of the basin via the Basin-Mod technique was carried out and the subsidence-buried history and thermal history of the Taibei depression were inverse calculated: it had undergone a early rapid rift and sag, then three times of uplift and erosion, and finally depressed and been buried. The Taibei depression contains a huge thick clastic sedimentary rock of marine facies, transitional facies and continental facies on the complex basement of ante-Jurassic. It is a part of the back-arc rifting basins occurred during the Mesozoic and Cenozoic. The author analyzed the diagenesis and thermal fluid evolution of this area via the observation of cathodoluminescence, scanning electron microscope and thin section, taking advantage of the evidences of magma activities, paleo-geothermics and structural movement, the author concluded that there were at least three tectonic-thermal events and three epochs of thermal-fluid activities; and the three epochs of thermal-fluid activities were directly relative to the first two tectonic-thermal events and were controlled by the generation and expulsion of hydrocarbon in the source rock simultaneously. Based on these, this paper established the corresponding model between the tectonic-thermal events and the thermal-fluid evolution of the Taibei Depression, which becomes the base for the study on the chimney structures. According to the analyses of the gas-isotope, LAM spectrum component of fluid inclusion, geneses of CO_2 components and geneses of hydrocarbon gases, the author preliminarily verified four sources of the thermal fluid in the Taibei Depression: ① dehydration of mud shale compaction, ② expulsion of hydrocarbon in the source rock; ③ CO_2 gas hydro-thermal decomposition of carbonatite; ④magma-derived thermal fluid including the mantle magma water and volatile components (such as H_2O, CO_2, H_2S, SO_2, N_2 and He etc.). On the basis of the vitrinite reflectance (Ro), homogenization temperature of fluid inclusion, interval transit time of major well-logging, mud density of the wells, measured pressure data and the results of previous studies, this paper analyzed the characteristics of the geothermal fields and geo-pressure fields for the various parts in this area, and discussed the transversal distribution of fluid pressure. The Taibei depression on the whole underwent a temperature-loss process from hot basin to cold basin; and locally high thermal anomalies occurred on the regional background of moderate thermal structure. The seal was primarily formed during the middle and late Paleocene. The overpressured system was formed during the middle and late Eocene. The formation of overpressured system in Lishui Sag underwent such an evolutionary process as "form-weaken-strengthen-weaken". Namely, it was formed during the middle and late Eocene, then was weakened in the Oligocene, even partly broken, then strengthened after the Miocene, and finally weakened. The existence of the thermal fluid rich in volatile gas is a physical foundation for the boiling of the fluid, and sharply pressure depletion was the major cause for the boiling of the fluid, which suggests that there exists the condition for thermal fluid to boil. According to the results of the photoelastic simulation and similarity physical experiments, the geological condition and the formation mechanism of chimnestructures are summarized: well compartment is the prerequisite for chimney formation; the boiling of active thermal fluid is the original physical condition for chimney formation; The local place with low stress by tension fault is easy for chimney formation; The way that thermal fluid migrates is one of the important factors which control the types of chimney structures. Based on where the thermal fluid come from and geometrical characteristics of the chimney structures, this paper classified the genetic types of chimney structures, and concluded that there existed three types and six subtypes chimney structures: organic chimney structures generated by the hydrocarbon-bearing thermal fluid in middle-shallow layers, inorganic and commingling-genetic chimney structures generated by thermal fluid in middle-deep layers. According to the seismic profiles interpretations, well logging response analysis and mineralogical and petrological characteristics in the study area, the author summarized the comprehensive identification marks for chimney structures. Especially the horizon velocity analysis method that is established in this paper and takes advantage of interval velocity anomaly is a semi-quantitative and reliable method of chimney structure s identification. It was pointed out in this paper that the occurrence of the chimney structures in the Taibei depression made the mechanism of accumulation complicated. The author provided proof of episodic accumulation of hydrocarbon in this area: The organic component in the boiling inclusion is the trail of petroleum migration, showing the causality between the boiling of thermal fluid and the chimney structures, meanwhile showing the paroxysmal accumulation is an important petroleum accumulation model. Based on the evolutionary characteristics of various types of chimney structures, this paper discussed their relationships with the migration-accumulation of petroleum respectively. At the same time, the author summarized the accumulating-dynamical models associated with chimney structures. The author analyzed such accumulation mechanisms as the facies state, direction, power of petroleum migration, the conditions of trap, the accumulation, leakage and reservation of petroleum, and the distribution rule of petroleum. The author also provides explanation for such practical problems the existence of a lot of mantle-derived CO_2, and its heterogeneous distribution on plane. By study on and recognition for chimney structure, the existence and distribution of much mantle-derived CO_2 found in this area are explained. Caused by tectonic thermal activities, the deep magma with much CO_2-bearing thermal fluid migrate upward along deep fault and chimney structures, which makes two wells within relatively short distance different gas composition, such as in well LF-1 and well LS36-1-1. Meanwhile, the author predicted the distribution of petroleum accumulation belt in middle-shallow layer for this area, pointed out the three favorable exploration areas in future, and provided the scientific and deciding references for future study on the commingling-genetic accumulation of petroleum in middle-deep layer and the new energy-gas hydrate.

湛江湖光岩玛珥湖55ka以来植硅体化石记录及古环境变迁

The study of biogenic proxy of tropical and subtropical regions provides important evidence about the process and history of vegetation and environmental changes, and is of globally importance for understanding the dynamic mechanism of paleoclimatic and paleoenvironmental changes. The sediments from the Huguangyan Maar lake in Guangdong Province offer a continuous high-resolution record of the past 55 ka about environmental and vegetational changes. The studies of chronology, and physical, chemical environmental proxies have provided much important information about the paleoenvironmental and paleoclimatic histories. The phytolith, a new biogenicl proxy, has been used to determine the nature and types of plants in this area since the last 55 ka. This study presents a preliminary result about the characteristics of phytolith shapes, the variations of the fossils assemblages, and their significance for environmental changes. Moreover, the author probes the process of special specie evolution and their relationship to climatic parameters. The history of fire has been reconstructed based on the variations in charcoals. The main results and conclusions include: 28 types of phytoliths from 233 samples have been identified. Their environmental meanings are investigated in detail. Based on the variations in phytolith associations, the history and process of climatic and environmental changes in the last 55 kaBP have been established for this region. Climatic changes experienced eight intervals during this period, showing the variations of hot-humid to cool-try climate in the ten thousands years scale, and a shorter dry-hot climate condition in millennial scale. The history of palm plant has been established in this region. Two peaks appeared from 55-39 ka and since the Holocene. Plants in Bambusoideae have been growing in this area all the period, representing the impact of the East Asian summer monsoon. Bamboo plants have similar tendency in their abundance to palm plants, but with a lag of 1-2 ka BP. Panicoideae plants, the representative of C4 plants, have 6 flourishing periods occurred at 54.5, 44, 41.5, 32.5, 14, and 10 kaBP, respectively, reflecting 6 times short-term arid events. Charcoal record from the Huguang Marr lake reveals the history of nature fire, that mostly happened in dry period of last glacial from 55-10 kaBP, centered at 50-45, 40-35, 30-25, and 20-15kaBP, showing about a cycle of 10,000 years.

花岗岩风化土微观结构及其工程地质特性研究

Saprolite is the residual soil resulted from completely weathered or highly weathered granite and with corestones of parent rock. It is widely distributed in Hong Kong. Slope instability usually happens in this layer of residual soil and thus it is very important to study the engineering geological properties of Saprolite. Due to the relic granitic texture, the deformation and strength characteristics of Saprolite are very different from normal residual soils. In order to investigate the effects of the special microstructure on soil deformation and strength, a series of physical, chemical and mechanical tests were conducted on Saprolite at Kowloon, Hong Kong. The tests include chemical analysis, particle size analysis, mineral composition analysis, mercury injection, consolidation test, direct shear test, triaxial shear test, optical analysis, SEM & TEM analysis, and triaxial shear tests under real-time CT monitoring.Based on the testing results, intensity and degree of weathering were classified, factors affecting and controlling the deformation and strength of Saprolite were identified, and the interaction between those factors were analyzed.The major parameters describing soil microstructure were introduced mainly based on optical thin section analysis results. These parameters are of importance and physical meaning to describe particle shape, particle size distribution (PSD), and for numerical modeling of soil microstructure. A few parameters to depict particle geometry were proposed or improved. These parameters can be used to regenerate the particle shape and its distribution. Fractal dimension of particle shape was proposed to describe irregularity of particle shapes and capacity of space filling quantitatively. And the effect of fractal dimension of particle shape on soil strength was analyzed. At the same time, structural coefficient - a combined parameter which can quantify the overall microstructure of rock or soil was introduced to study Saprolite and the results are very positive. The study emphasized on the fractal characteristics of PSD and pore structure by applying fractal theory and method. With the results from thin section analysis and mercury injection, it was shown that at least two fractal dimensions Dfl(DB) and Df2 (Dw), exist for both PSD and pore structure. The reasons and physical meanings behind multi-fractal dimensions were analyzed. The fractal dimensions were used to calculate the formation depth and weathering rate of granite at Kowloon. As practical applications, correlations and mathematical models for fractal dimensions and engineering properties of soil were established. The correlation between fractal dimensions and mechanical properties of soil shows that the internal friction angle is mainly governed by Dfl 9 corresponding to coarse grain components, while the cohesion depends on Df2 , corresponding to fine grain components. The correlations between the fractal dimension, friction angle and cohesion are positive linear.Fractal models of PSD and pore size distribution were derived theoretically. Fragmentation mechanism of grains was also analyzed from the viewpoint of fractal. A simple function was derived to define the theoretical relationship between the water characteristic curve (WCC) and fractal dimension, based on a number of classical WCC models. This relationship provides a new analytical tool and research method for hydraulic properties in porous media and solute transportation. It also endues fractal dimensions with new physical meanings and facilitates applications of fractal dimensions in water retention characteristics, ground water movement, and environmental engineering.Based on the conclusions from the fractal characteristics of Saprolite, size effect on strength was expressed by fractal dimension. This function is in complete agreement with classical Weibull model and a simple function was derived to represent the relationship between them.In this thesis, the phenomenon of multi-fractal dimensions was theoretically analyzed and verified with WCC and saprolite PSD results, it was then concluded that multi-fractal can describe the characteristics of one object more accurately, compared to single fractal dimension. The multi-fractal of saprolite reflects its structural heterogeneity and changeable stress environment during the evolution history.

Environmental Mechanics Research in China

By recalling mankind's path during past 50 years in the present article, we mainly highlight the significance of environmental issues today. In particular, two major factors leading to environment deterioration in China such as water resources and coal burning are stressed on. Present-day environmental issues are obviously interdisciplinary, of multiple scales and multi-composition in nature. Therefore, a process-based approach for environment research is absolutely necessarily. A series of sub-processes, either physical, chemical or biological, are subsequently analyzed in order to established reasonable parameterization scheme and credible comprehensive model. And we are now in a position to answer questions still open to us, improve existing somewhat empirical engineering approaches and enhance quantitative accuracy in prediction. To illustrate this process-based research approach, three typical examples associated with the Yangtze River Estuary, Loess Plateau and Tenggeli Desert environments have been dealt with respectively. A theoretical model of vertical flow field accounting for runoff and tide interaction has been established to delineate salinity and sediment motion which are responsible for the formation of mouth bar at the outlet and the ecological evolution there. A kinematic wave theory combined with the revised Green-Ampt infiltration formula is applied to the prediction of runoff generation and erosion in three types of erosion region on the Loess Plateau. Three approaches describing water motion in SPAC system in arid areas at different levels have been improved by introducing vegetation sub-models. However, we have found that the formation of a dry sandy layer and biological crust skin are additional primary causes leading to deterioration of water supply and succession of ecological system.

Micro-systems for Optical Protein-Chip

Protein-Chip as micro-assays for the determination of protein interaction, the analysis, the identification and the purification of proteins has large potential applications. The Optical Protein-Chip is able to detect the multi-interaction of proteins and multi-bio-activities of molecules directly and simultaneously with no labeling. The chip is a small matrix on solid substrate containing multi-micro-area prepared by microfabrication with photolithography or soft lithography for surface patterning, and processed with surface modification which includes the physical, chemical, and bio-chemical modifications, etc. The ligand immobilization, such as protein immobilization, especially the oriented immobilization with low steric hindrance and high bio-specific binding activity between ligand and receptor is used to form a sensing surface. Each area of the pattern is corresponding to only one bioactivity. The interval between the areas is non-bioactive and optically extinctive. The affinity between proteins is used to realize non-labeling microassays for the determination of protein identification and protein interaction. The sampling of the chip is non-disturbing, performed with imaging ellipsometry and image processing on a database of proteins.

Membrane Deformability and Membrane Tension of Single Isolated Mitochondria

Mitochondria dynamics is crucial to many biological processes such as mitochondria fusion and fission, which is highly correlated to the mechanics of single mitochondria. However, the mechanobiological coupling of mitochondria has been poorly understood. Here membrane deformability and membrane tension of individual mitochondria isolated from MtDsRed labeled human embryonic T-Rex-293 kidney cells were measured using a micropipette aspiration assay. The results demonstrated that membrane deformation of isolated mitochondria exhibited an elastic transition phase followed by an equilibrium phase, and mitochondrial membrane tension was proportional to the area compressibility. It was also indicated that mitochondrial membrane deformability was significantly affected by physical chemical factors such as osmotic pressure or pH value, and was further correlated to mitochondrial functionality in different respiratory states and Ca2+ regulation. These findings provide a new insight into understanding the mechanical regulation of mitochondrial physiology.

Mechanism study on the frequent variations of cell-bound microcystins in cyanobacterial blooms in Lake Taihu: Implications for water quality monitoring and assessments

Although Microcystis-based toxins have been intensively studied, previous studies using laboratory cultures of Microcystis strains are difficult to explain the phenomenon that microcystin concentrations and toxin variants in natural blooms differ widely and frequently within a short-term period. The present study was designed to unravel the mechanisms for the frequent variations of intracellular toxins related to the differences in cyanobacterial colonies during bloom seasons in Lake Taihu, China. Monitoring of Microcystis colonies during warm seasons indicated that the variations in microcystins in both concentrations and toxin species were associated with the frequent alteration of Microcystis colonies in Lake Taihu. High concentration of microcystins in the blooms was always associated with two Microcystis colonies, Microcystis flos-aquae and Microcystis aeruginosa, whereas when Microcystis wesenbergii was the dominant colonial type, the toxin production of the blooms was low. Additionally, environmental factors such as temperature and nutrition were also shown to have an effect on the toxin production of the blooms, and may also potentially influence the Microcystis species present. The results of the present study provides insight into a new consideration for quick water quality monitoring, assessment and risk alert in cyanobacterium- and toxin-contaminated freshwaters, which will be beneficial not only for water agencies but also for public health. (C) 2009 Elsevier Ltd. All rights reserved.