Effect of support on chromium based catalysts for the oxidative dehydrogenation of C2H6 with CO2 to C2H4

The oxidative dehydrogenation of ethane (ODE) with CO2 to C2H4 has been studied over a series of Cr-based catalysts using SiO2, Al2O3, (MCM-41 zeolite) MCM-41, MgO and Silicate-2 (Si-2) as the supports. TPR, NH3-TPD, and EPR characterizations of catalysts were carried out to investigate the reduction property of Cr species on different supports, the acidities of catalysts and Cr species of 6Cr/SiO2 catalysts, respectively.

Correlation between the characteristics and catalytic performance of Ni-V-O catalysts in oxidative dehydrogenation of propane

Ni - V - O series catalysts for the oxidative dehydrogenation (ODH) of propane were prepared and characterized by BET, XRD, H-2- TPR, O-2-TPD-MS and electrical conductivity. At 425 degreesC a C3H6 selectivity of 49.9% was observed on Ni0.9V0.1OY at a C3H8 conversion of 19.4%, and the obtained selectivity is almost two times higher than that over NiO at the roughly same conversion of C3H8. The mobile oxygen species created by the interaction of NiO and V2O5 has been found in the composite catalysts by O-2-TPD-MS and electrical conductivity studies, which seems to be responsible for the enhanced selectivity of the propane oxidative dehydrogenation.

Oxidative dehydrogenation of propane in a dense tubular membrane reactor

Oxidative dehydrogenation of propane (ODP) to propylene was investigated in a dense tubular membrane reactor made of Ba0.5Sr0.5Co0.8Fe0.2O3-delta (BSCF) at 700degreesC and 750degreesC. The propylene selectivity in the membrane reactor (44.2%) is much higher than that in the fixed-bed reactor (15%) at the similar propane conversion (23-27%). Higher propylene selectivity in the membrane reactor was attributed to the lattice oxygen (O2-) supplied through the membrane.

Mn-containing AlPO-11 and SAPO-11 catalysts for simultaneous isomerization and dehydrogenation of n-butane

MnAPO-11 and MnAPSO-11 were synthesized hydrothermally, and supported Mn-AlPO-11 and Mn-SAPO-11 were also prepared for comparison. Characterization results showed that there were differences in acidity and reducibility caused by the different incorporation methods of manganese. The manganese species in the samples also weakened the metallic properties of the palladium particles when the latter was added into the catalysts. Catalytic testing results for dehydroisomerization of n-butane indicated that incorporation of manganese increased the selectivity toward isomerization products. The highest isobutene selectivity (34.86%) could be obtained over a Pd/MnAPO-11 catalyst. When a combined catalyst system containing Pd/SAPO-11 and MnAPSO-11 was used in a single bed of two layers, the isobutene selectivity could be greatly improved, as compared to the single catalyst alone.

Combination of CH4 oxidative coupling reaction with C2H6 oxidative dehydrogenation by CO2 to C2H4

A new process has been suggested for converting natural gas to ethylene by combining oxidative coupling of methane with ethane dehydrogenation to provide an efficient method for the utilization of thermicity and CO2. From their thermodynamics, it is clear that the exothermicity from CH4 oxidative coupling reaction (DeltaH(800degreesC) = -174.3 kJ mol(-1)) can support C2H6 dehydrogenation by CO2 (DeltaH(800degreesC) = + 180.2 kJ mol(-1)). Meanwhile, the two reactions can be conducted under the same reaction conditions, such as the reaction temperature and reaction pressure as well as space velocity. In addition, the CO2 yielded from CH4 oxidative coupling reaction can be directly used for C2H6 dehydrogenation. Two kinds of catalyst are developed for this combined process with an achievement, from which C2H4 content in tail gas can reach attractively 16.4%, which can be used directly to produce ethylbenzene by the alkylation of benzene. (C) 2002 Elsevier Science Ltd. All rights reserved.

Polyaniline as nonmetal catalyst for styrene synthesis by oxidative dehydrogenation of ethylbenzene

Polyaniline was used as a nonmetal catalyst in the oxidative dehydrogenation of ethylbenzene and yield of 22.9% at 573 K and similar to 40% at 673 K were obtained, respectively. An indirect oxidative dehydrogenation mechanism was proposed based on the results of pulse reactions.

A new route to control product selectivity in the oxidative dehydrogenation of cyclohexane and cyclohexene

The product selectivity can be controlled by adding acetic acid in feed over vanadium phosphate (VPO) in gas phase oxidative dehydrogenation (ODH), in which cyclohexane and cyclohexene are oxidized to cyclohexene and 1,3-cyclohexadiene (1,3-CHD), respectively, at almost 100% selectivity. This approach is also an efficient method to capture the very unstable intermediates in the mechanism study.

Effect of different VOPO4 phase catalysts on oxidative dehydrogenation of cyclohexane to cyclohexene in acetic acid

alpha(1)-VOPO4, alpha(II)-VOPO4 and beta-VOPO4 have been investigated as catalysts for the gas phase oxidative dehydrogenation (ODH) of cyclohexane to cyclohexene with the addition of acetic acid (HOAc) in the feeds in a fixed bed reactor. Different VOPO4 phases showed different acidity and reducibility. beta-VOPO4 phase is more active than alpha(I)-VOPO4 and alpha(II)-VOPO4 in the ODH without acetic acid addition. In the presence of acetic acid, the acidity of the catalyst may play an important role in the ODH process. Due to higher acidity, alpha(I)-VOPO4 phase catalyst gives better catalytic performances than alpha(I)-VOPO4 and beta-VOPO4 for the ODH of cyclohexane by adding of acetic acid in the reactants.

Effects of acetic acid on product selectivity in gas phase oxidative dehydrogenation of cyclohexane

The effect of adding acetic acid on the product distribution in gas phase oxidative dehydrogenation of cyclohexane over alpha(1)-VOPO4 catalyst was investigated. The role of acetic acid in the reaction process was put forward. The proposed mechanism is that acetic acid take precedence of cyclohexane adsorbing on the active sites of alpha(1)-VOPO4 catalyst to form isolated active site. Thus, cyclohexene species can desorb quickly from the active sites, avoiding its deep oxidation dehydrogenation. Almost 100% selectivity to cyclohexene could be obtained when the molar ratio of acetic acid to cyclohexane was 12.9:1 at 450 degrees C, the conversion of cyclohexane was 6.9%.