Impact of Brunswick river mouth training walls on adjacent beaches, Brunswick heads, New South Wales, Australia

River training walls have been built at scores of locations along the NSW coast and their impacts on shoreline change are still not fully understood. In this study, the Brunswick River entrance and adjacent beaches are selected for examination of the impact of the construction of major training walls. Thirteen sets of aerial photographs taken between 1947 and 1994 are used in a CIS approach to accurately determine tire shoreline Position, beach contours and sand volumes, and their changes in both time and space, and then to assess the contribution of both tire structures and natural hydrodynamic conditions to large scale (years-decades and kilometres) beach changes. The impact of the training walls can be divided into four stages: natural conditions prior to their construction (pre 1959), major downdrift erosion and updrift accretion during and. following the construction of the walls in 1959 similar to 1962 and 1966. diminishing impact of the walls between 1966 and 1987, and finally no apparent impact between 1987 similar to 1994. The impact extends horizontally about 8 km updrift and 17 km downdrift, and temporally up to 25 years..

Paleoenvironment evolution of the East Philippine Sea recorded in the new-type ferromanganese crust since the terminal Late Miocene

From systemic research of microstructure, geochemistry, uranium-series and Be-10 isotope dating on a new-type deepwater ferromanganese crust from the East Philippine Sea, the paleoenvironment evolution of the target area since the terminal Late Miocene was recovered. The vertical section changes of microstructure and chemical composition are consistent in the studied crust, which indicate three major accretion periods and corresponding paleoenvironment evolution of the crust. The bottom crust zone was formed in the terminal Late Miocene (5.6 Ma) with loose microstructure, high detritus content and high growth rate. Reductions of mineral element content, accretion rate and positive Ce-anomaly degree at 4.6 Ma indicate temporal warming, which went against the crust accretion and finally formed an accretion gap in the terminal Middle Pliocene (2.8-2.7 Ma). The more active Antarctic bottom seawaters in the Late Pliocene (2.7 Ma) facilitated the fast transfer to the top pure crust zone. Hereafter, with the further apart of volcanic source and the keeping increase of eolian material (1.0 Ma), although surrounding conditions were still favorable, mineral element content still shows an obvious reducing trend. It thereby offers new carrier and data for the unclear paleoceanographic research of the target area since the terminal Late Miocene.

淤泥质潮滩地貌的遥感研究－以苏北辐射沙洲海岸为例

本文以具有典型特征的苏北淤泥质潮滩海岸作为研究区，利用1975-2003年间14景覆盖该地区的Landsat和SPOT卫星影像作为主要数据源，结合地面调查和验证工作，在遥感影像处理和地理信息系统分析技术的支持下，对区内潮滩、岸线、水边线和盐沼植被等进行遥感解译，分析苏北辐射沙脊群和沿岸地貌的空间分布特征和动态演变趋势。研究结果表明：苏北辐射沙脊群海域的潮汐水位过程的不同步现象普遍存在，限制了常规遥感数据在苏北潮滩地貌研究中的适用范围和解译精度；在人工判别的辅助下，多光谱遥感的非监督分类方法可以有效解译淤泥质潮滩的水边线；利用修改型土壤调整植被指数（MSAVI）可以较好地提取潮滩上的盐沼植被信息；苏北沿岸潮滩的快速淤长促进了盐沼植被带向海侧快速扩展，近年来持续的潮滩围垦工程则不断从陆侧侵占盐沼植被带，使盐沼植被带宽度减小乃至消失；在大规模人类活动和自然条件的共同影响下，苏北辐射沙脊群海岸的岸线发育趋于平直化，无序的潮滩围垦项目使得可垦滩地资源被过度消耗；1975～2002年间，研究区北部和南部沿岸的高潮滩整体上处于淤长状态，中部沿岸潮滩和离岸沙洲高潮滩则被大面积侵蚀；1999年以来，研究区内低潮滩部位开始形成有序排列的滩面地物，并表现出逐年大面积蔓延的趋势，可能是滩涂紫菜养殖区扩展的结果。

Preliminary study of the dynamic origin of the distribution pattern of bottom sediments on the continental shelves of the Bohai Sea, Yellow Sea and East China Sea

The bottom sediment types in the Bohai Sea, Yellow Sea and East China Sea (BYECS) are diversified, and their distribution pattern is very complicated. However, the bottom sediment types can be simplified to be sandy sediment, clayey sediment and mixed sediment, which comprise the complicated distribution pattern of bottom sediment in the BYECS. The continental shelves of the BYECS are broad, with shallow water depths and tidal currents which are permanent and dominate the marine dynamics in the BYECS. Based on numerical simulation of tidal elevations and currents in the BYECS, the rates of suspended load transport and bed load transport during a single tidal cycle for sediments of eight different grain size ranges are calculated. The results show that any sediment, whose threshold velocity is less than that of tidal current, has the same transport trend. Suspended load transport rare, bed load transport rate, and the ratio of the former to the latter decrease with grain size becoming coarser and coarser. The erosion/accretion patterns of sediments with different grain sizes are determined by the sediment transport rate divergences, and the results show that the patterns are the same for sediments with different grain sizes. Three main bottom sediment types, i.e. sandy sediment mainly composed of fine sand, clayey sediment mainly composed of silty clay, and mixed sediment mainly composed of fine sand, silt, and clay, are obtained by computation. The three bottom sediment types and their distribution pattern are consistent not only with sediment transport field and the sea bed erosion/accretion pattern obtained by simulation, but also with field data of bottom sediment types and divisions. In the BYECS, sand ridges form mainly in the areas with strong rectilinear tidal currents, sand sheets form mainly in the areas dominated by strong rotatory tidal currents, and clayey sediments, i.e. mud patches, form mainly in the areas with weak tidal currents. Hence, not only the sandy sediments but also the clayey sediments in the BYECS are formed under the control of the whole tidal current field of the BYECS. The three main bottom sediment types are not isolated respectively-in fact, they constitute a whole tidal depositional system. Under the condition with no cyclonic cold eddy, the clayey sediments in the BYECS can form in weak tidal current environments. Therefore, a cold eddy is not necessary for the deposition of clayey sediments in the BYECS. (C) 2000 Academic Press.

黄骅坳陷港西开发区河流相储层构型与剩余油分布模式研究

In the production tail of oilfield, water-cut is very high in thick channel sand oil reservoir, but recovery efficiency is relative low, and recoverable remaining oil reserves is more abundant, so these reserves is potential target of additional development. The remaining oil generally distributed with accumulation in certain areas, controlled by the reservoir architecture that mainly is the lateral accretion shale beddings in the point bar, so the study of reservoir architecture and the remaining oil distribution patterns controlled by architecture are very significant. In this paper, taking the Minghuazhen formation of Gangxi oilfield as a case, using the method of hierarchy analysis, pattern fitting and multidimensional interaction, the architecture of the meandering river reservoir is precisely anatomized, and the remaining oil distribution patterns controlled by the different hierarchy architecture are summarized, which will help to guide the additional development of oil fields. Not only is the study significant to the remaining oil forecasting, but also it is important for the theory development of reservoir geology. With the knowledge of sequence correlation and fluvial correlation model, taking many factors into account, such as combination of well and seismic data, hierarchical controlling, sedimentary facies restraint, performance verification and 3-D closure, an accurate sequence frame of the study area was established. On the basis of high-resolution stratigraphic correlation, single layer and oil sand body are correlated within this frame, and four architecture hierarchies, composite channel, single channels, point bars and lateral accretion sandbody are identified, The result indicates that Minghuazhen Formation of Gangxi oilfield are dominated by meandering river deposition, including two types of channel sandbodies, narrow band and wide band channel sandbody, and each of them has different characteristics of facies variation laterally. Based on the identification of composite channel, according to the spatial combination patterns and identified signs of single channel, combined with channel sandbody distribution and tracer material data, single channel sandbodies are identified. According to empirical formula, point-bar scales of the study area are predicted, and three identification signs are summarized, that is, positive rhythm in depositional sequence, the maximum thick sand and near close to the abandoned channel, and point bars are identified. On the basis of point bar recognition, quantitative architecture models inner point bar are ascertained, taking the lateral accretion sand body and lateral accretion shale beddings in single well as foundation, and quantitative architecture models inner point bar as guidance, and result of tracer material data as controlling, the the lateral accretion sand body and lateral accretion shale beddings are forecasted interwell, so inner architecture of point bar is anatomied. 3-D structural model, 3-D facies model and 3-D petrophysical properties models are set up, spatial distribution characteristics of sedimentary facies and petrophysical properties is reappeared. On the basis of reservoir architecture analysis and performance production data, remaining oil distribution patterns controlled by different hierarchy architecture units, stacked channel, single channel and inner architecture of point bar, are summarized, which will help to guide the additional development of oil fields.

东北亚构造-盆地演化及油气资源控制作用

The oil and gas potential of Northeast Asia is enormous, but the degree of exploration is very low in Northeast Asia (the degree is below 3%-10%).The reasons are as follows: First, it is relatively difficult to study the oil and gas bearing basins(OGB), which are of multiple types, in different tectonic settings, with complex geologic frameworks and with long-term geologic evolution. Secondly, because of the non-equilibrium in development of economy and regional market, application of theories and techniques and the research levels in different countries, the conclusions are not conformable, and even contradictory. Thirdly, most of the former researches were limited to one territory or one basin, and lack of systematical and in-depth study on geotectonic evolution, classification of basins, and the evaluation of hydrocarbon resources. In this thesis, integrated study of the regional tectonic feature and basin features of Northeast Asia was done, to understand the basin evolution history and the controlling action on oil and gas. Then, new conclusions are and exploration proposals are as following: 1. Geotectonic evolution in Northeast Asia: The main structural motion system in Paleozoic Era was longitudinal, and in Meso-cenozoic was latitudinal with the Pacific Ocean. The whole evolution history was just the one of pulling-apart, cutting-out, underthrusting and collision of the Central Asia- Mongolia Ocean and the Pacific Ocean. 2. The evolution characteristics of basins in Northeast Asia: mainly developed from longitudinal paste-up, collision and relaxation rifting motion in Paleozoic-Early Mesozoic Era and from underthrust, accretion, and receding of subducted zone of the Pacific Ocean in Late Mesozoic Era-Cenozoic Era. 3. The research in basin classification of Northeast Asia: According to geotectonic system, the basins can be classified into three types: intracratonic, pericratonic and active zone basin. And they can be further classified into 18 different types according to genetic mechanism and dynamic features. 4. The master control factors of oil and gas accumulation in Northeast Asia: high quality cap-rock for craton and pericrationic basin, the effective source rock and high quality cap-rock for Mesozoic rifted basins, intra-arc, fore-arc and back-arc basins. Graded exploration potential of oil and gas for basin in Northeast Asia according to 7 factor, hereby, divided the oil and gas potential of basins into 5 levels. 5. Evaluation of hydrocarbon resources: The difference of resource potential among these basins is huge in Northeast Asia. The evaluation of Mesozoic rifted basin and Pacific Ocean basin showed that the large scale rifted basin and retroarc basin(including backarc marginal sea basin) have great resource potential. 6. The writer believes that the next step should pay more attention to the evaluation of petroleum resource in Far East part of Russia and trace them. On the other hand, according to integrated analysis of oil/gas resource potential and the operation difficulty in this area, suggests that East-Siberia basin, East-Gobi-Tamchag basin, Sakhalin basin, North-Okhotck basin, West-Kamchatka basin could be as cooperation priority basins in future.

中国东部沙地物源示踪及地质意义

Heavy mineral assemblages, chemical compositions of diagnostic heavy minerals such as garnet and tourmaline, and U-Pb ages and Hf isotopic compositions of zircons are very effective means to determine sediment provenance. An integrated application of the above provides insight on the lithologies, crystallization ages and crustal formation ages of the parent magma of sediment source areas. As a result, the locations and characteristics of potential source areas can be constrained and contributions of different source regions may be evaluated. In addition, the study provides evidence for the magmatic and tectonic history of source areas using a novel approach. The heavy mineral assemblages, and chemical compositions of detrital garnets and tourmalines, U-Pb ages and Hf isotopic compositions of zircons for sand and loess samples deposited since the Last Glacial Maximum (LGM) from the Hulunbeier, Keerqin and Hunshandake sandlands were analyzed and compared to those of central-southern Mongolia, the central Tarim and surrounding potential source areas, the Central Asian Orogenic Belt (CAOB) and North China Craton (NCC). The following remarks on provenance and tectonic history can be made: 1. The source compositional characteristics of the Hulunbeier, Keerqin and Hunshandake sandlands are similar. They are derived from the CAOB and NCC whose contributions for the Keerqin and Hunshandake sandland are about 50%. For the Hulunbeier sandland it is somewhat less, about 40%. 2. Loesses around of the sandlands have the identical source signiture as the sands, implying that they are sorted by the same wind regime. 3. The source characteristics of the present and LGM sands are the same, providing direct evidence that the present sands originated from the reworking of LGM sands. 4. The provenance characteristics of the three sandlands differ from those of the Tarim. As a result, the possibility that the three eastern sandlands were sourced from the Taklimakan desert can be ruled out. 5. The source compositions of sand samples derived from the CAOB indicate that the occurrence of Archean and Paleoproterozoic metamorphic basement rocks is limited and continuous subduction-accretion events from the Neoproterozoic to the Mesozoic occurred. This implies that the CAOB is a orogenic collage belt similar to the present day southwest-Pacific, and formed by the amalgamation of small forearc and backarc ocean basins occurring between island arcs and microcontinents during continuous collision and accretion. The Hf isotopic signitures of detrital zircons indicate that large amounts of juvenile mantle materials were added to the CAOB crust during the Phanerozoic.

孤岛油田曲流河微相单砂体储层建筑结构及挖潜方向研究

In the intermediary and later stage of oil field development, remaining oil disperses fiercely, the contradiction in the layer has become the main problem and the distribution of remaining oil is transforming to the difference of single sand-body. So, the fine description research of reservoir is becoming a tendency and the methods of remaining oil research need new developments. In the research of “The Single-sand-body Architectural Element and Potentiality Analysis Research of Meandering River, GuDao Oil Field”, the research principle is analytical hierarchy process and schema prescription what are reservoir fine description methods under the condition of dense well pattern. The knowledge of regional sedimentary system and sedimentary facies is the foundation of this research. According to the 3D distribution model of the microfacies sand-body of fluvial facies, stratigraphic unit classification & coenocorrelation of 154 wells are completed in the research of meandering river sand-body in Ng3-4. In this research, the 3D distribution of microfacies sand-body in the main layers are settled. The architectural element model of Ng4 point bar is analysed using the drill core and FMI data. According to the overgrow model of point bar, the surfaces of lateral accretion is traced and the architectural element model of point bar is settled. In the research, the control of micro-facies sand-body of meandering river to the distribution of remaining oil is analysed and the potential area is proposed. All these will play an important role in the development of GuDao oil field. In this research, abundant of logging data, drill core data and production performance data are used to analyse the contributing factor of single sand-body in the Ng3-4 meandering river. Using the technology of geological modeling, all that are researched including the 3D distribution scales of meandering river point bar, the control affection of inner lateral accretion layer to the distribution of oil & gas and remaining. Then, the way of remaining oil development in the sand-body of meandering river is improved. The innovation of the research technology includes (1) the presentation of the conception and research methods of micro-facies sand-body (2) enriching the content of reservoir architectural element research and (3) to renew the research method of remaining oil analysis. The research has practiced with obvious effect.(1)It is deepened into understand the river facies reservoir construction of Gudao oil field, By Building the reservoir construction and studying the effect of diffent deposit or geological interface to fluid partition and to the distribution of the remaining oil, we improved the understanding to the distribution of the remaining oil；(2)By building the distribution mod of the remaining oil in the reservoir construction and making the remaining oil description detailed,the development direction of old oil field is more clear；(3)Expanded the application scales of the horizontal well and enhanced the application effects of the horizontal well technique , we designed and drilled 23 ports horizontal wells in all , the cumulative hydrocarbon production is 10.6*104 t；(4) According to the findings of the internal building structure in reservoir of the fluvial facies in the region of interest, and uniting the injection/production corresponding states、the producing history and the dynamic monitoring documents of the oil/water wells in the flooding units , we researched the residual oil distribution in the point bar , and found the distribution regular patterns of the remaining oil, and comprehended the distribution of the remaining oil . In base of that , we proceeded the optimizing designs of the oil well potentialities , and advanced the effect of the treatment potentials . It is proved that , it was very important that internal building structure research of the single sand body of reservoir for guiding the high efficiency potentialities of the remaining oil in the high water cut stage .

大兴安岭北段晚中生代火山岩地球化学特征及其地质意义

This thesis mainly concentrates on the geochronology, prtrology, elemental geochemistry and Sr-Nd-Pb-Hf isotopic geochemistry of the volcanic rocks in north Da’Hinggan Mountain. By analyzing the data obtained in this study and data from other people, this thesis explored the age distribution, petrology and mineralogy and geochemistry characteristics of the volcanic rocks in north Da’Hinggan Mountain. Furthermore, this thesis speculated upon the source characteristics of these volcanic rocks and their implications for the tectonic evolution and crust accretion. According to the twenty Ar-Ar ages, four zircon U-Pb SHRIMP ages and two Zircon U-Pb LA-ICP-MS ages, the duration of the eruption of the Late Mesozoic volcanic rocks in north Da’Hing Mountain was about 160Ma-106Ma. Most of these volcanic rocks belong to early Cretaceous and the late Jurassic volcanic rocks are only restricted in Manzhouli. The bulk of the late Mesozoic volcanic rocks are high-K calc-alkaline rocks. Only a small portion of these volcanic rocks are shoshonites. These rocks are mainly intermediate or acid and the basic rocks usually have higher alkaline contents. Rock types are very complex in this region. These volcanic rocks have a large TiO2 variation and the Al2O3 and alkaline contents are high. From the point of mineralogy, the plagioclases in these volcanic rocks are oligoclases, andesines and labradorites, and the labradorites are more common. Most pyroxenes in these volcanic rocks are augites which belong to clinopyroxene. The source of the Late Mesozoic volcanic rocks was an enriched lithospheric mantle. When the magma en route to the surface it was contaminated by crust material slightly and had some fractional crystallization. These rocks which mainly belong to high-K calc-alkaline series were one of the results of postorogenic tectonic-magmatic activities. The upwelling in late Mesozoic supplied heat to melt the enriched lithospheric mantle which was resulted from the subduction of paleo-Asian Ocean and/or Mengol-Okhotsk ocean. These late Mesozoic volcanic rocks are also important to the upper crustal accretion of north Da’Hinggan Mountain since the late Mesozoic. These volcanics and the contemporary emplacement of granites and the basaltic underplating in combination fulfilled the crust accretion history in north Da’Hinggan Mountain in Late Mesozoic.

复杂断块油气藏成藏机理和剩余油预测

Complex fault block reservoir is very important type in chinese oilfield.The reservoir have for many years and it has been the important issue of oil-gas exploration and development in china that how to increase reserves and production. Therefore,taking the Pucheng-oil field as an example, the article intensive study the geologic feature of oil pool, correctly recognize the rule of oil-gas accumulation and based on the fine representation of the characteristic of reservoir, research the remaining oil in high developed area,which is important for progressive exploratioon and development and taping the remaining oil. The article multipurpose uses the data of geology,drilling,wellloging, analysis and assay and so on, under the guidance multi-disciplinary theory, intensify the comprehension of the geologic feature of oil pool in high developed oil field. Based on the high-resolution sequence stratigraphic framework ,the article points out that Es_2 upper 2+3 reservoir in the south area of Pucheng oilfield is in the depositional environment of Terminal Fan, which has constant supply of sedimentary source ,and build the sedimentation model. Studies have shown that the major reservoir in work area is the distributary channel sandbody in central Sub-facies of Terminal Fan，secondary is both lateral accretion sandbodies of channel sands，nearby and far away from the channel overflowing sandbodies in front of the fan. The article analyze the effect of depth of burial of the reservoir, sandstone structure, strata pressure and bioturbate structure on control action of physical property for reservoir and indicate that deposition and diagenesis are major controlling factors.By building the model of reservoir heterogeneity, the article show the magnitude of reservoir heterogeneity ,the genesis and identification mark of Interlayer and build the the model of interlayer. in this area the vertical distribution of interlayer is complicated,but the intraed interlayer distribute steady. Thick interlayer is steady and the thin is relatively spreaded. By building models of fault sealing,stress field and fluid potential field of the south of the pucheng oil field, the regular pattern of fluid migration and accumulation runs out. By researching the elements of oil accumulation, migration pathway and accumulation period with quantification and semiquantitative methods,we bulit the oil-gas reservoir-forming mode of the south of the pucheng oil field,which will be the foundation of the rolling exploratory development in the future. We promulgated the master control element and the rule of distribution of the remaining oil with the upside 2+3 oil layer in shaer in the south of the pucheng oil field as an example.In this area, the formation and the distribution of the remaining oil is controled by the sedimentary microfacies, reservoir heterogeneity,fault and reservoir engineering. The remaining oil is concentrated in the vicinity of the gas cap, updip of the fault block and the area with incomplete flooding. Remaining oil saturation in some area can get 50%, so there are many places in which we can enhance oil recovery.

内蒙古中部道郎和都格铜多金属矿的地质特征矿床类型及找矿模式研究

Daolangheduge copper polymetallic deposit is located on east edge of Ondor Sum-Bainaimiao metallogenic belt, which is a prospective area of porphyry copper deposit, in Xianghuangqi of central Inner Mongolia. Geotectonically, it occurred in the continental margin accretion belt along the north margin of North China Plate, south of the suture zone between North China Plate and Siberian Plate. The intrusive rocks in this area mainly consist of intermediate-acid magmatic rocks, and the quartz veins, tourmaline veins and the transitional phase are comparatively developed. According to our research, the ore-bearing rock body is mainly quartz diorite while the surrounding rock is mainly biotite granite. Besides, the wall rock alteration are mainly propylitization, pyritization and silicification, which consist of epidotization, actinolitization, chloritzation and so on. The metallic minerals are mainly chalcopyrite and pyrite. In addition, the primary ore is mainly of quartz-chalcopyrite-pyrite type. Above all, Daolangheduge copper polymetallic deposit is suggested to be categorized in the porphyry copper type. With isotopic dating and geochemical research on quartz diorite of ore-bearing rock body, the zircon LA-ICP-MS U-Pb dating of two samples yields an age of 266±2 Ma, falling into the range of late Permian Epoch. It is the first accurate age data in Xianghuangqi area, so it should play a key role in the research of deposit and magmatic rocks in this area. With the major elements and trace elements analysis of 14 samples, the quartz diorite should be among the calc-alkaline series, the geochemical characteristics show higher large-ion lithophile elements of Rb, Sr and LREE, low high-field strength elements of Nb, Ta and high transition elements of Cu, Cr . Also, the REE patterns have negative Eu anomalies. With the same analysis of 4 sample for the biotite granite, the geochemical characteristics show higher Rb, Th,, Zr, Hf and LREE, low Nb, Sm and HREE and Eu has no anomaly. It should be among the calc-alkaline series, over aluminum quality and has characteristics of Adakites. According to isotopic dating and geochemical characteristics of ore-bearing rock body, it is suggested that its materials mainly derived from upper mantle that had fractional crystallization and its magma source region may be affected by fluid metasomatism of paleo-asian ocean. It should be an extensional process of post-orogeny according to regional tectonic evolution. Consequently, because of the decrease of temperature and pressure, the ore forming fluid was raised to surface and mineralized accompanied by magmatic activity which might occur in south of the suture zone. By geological survey, further geophysical and geochemical work is needed. In this area, we have accomplished high precision magnetic prospecting, high density electrical survey, gravity prospecting, soil geochemical prospecting, X-ray fluorescence analyzer prospecting and so on. According to geophysical and geochemical abnormal and surface occurrence, 11 drills are arranged to verification. The type of ores are mainly quartz-chalcopyrite-pyrite ores within 3 drills by drill core logging. Although the grade as well as the scale of already-found Cu deposits are insufficient for industrial exploitation, the mineralization prospect in this region is supposed to be great and the potential in mineral exploration at depth is excellent.

碎屑锆石年龄和Nd-Hf同位素组成对扬子基底演化的制约

The South China craton was formed by the collision of the Yangtze and Cathaysia blocks during the Neoproterozoic Jiangnan orogeny (also termed as the Jingnin or Sibao orogeny in Chinese literature). Basement rocks within the Yangtze block consist mainly of Proterozoic sediments of the Lengjiaxi and Banxi Groups. U-Pb ages of detrital zircons obtained by the LA-ICP-MS dating technique imply that the deposition of the Lengjiaxi Group continued until the Neoproterozoic. The youngest detrital zircons suggest a maximum deposition age of ~830 Ma for the Lengjiaxi Group, consistent with the initiation time of the deposition of the overlying Banxi Group, likely indicating continuous deposition of these two groups and a short temporal hiatus (~10 Ma) between the Neoproterozoic sedimentary rocks distributed in the South China craton. Detrital zircons from both the Lengjiaxi and Banxi Groups have a wide range of εHf(t) values from -12 to 14.2 and a continuous Nd and Hf model age spectrum from ~820 Ma to 2200 Ma. Some grains have model ages ranging up to ca. 2.9-3.5 Ga, indicating that both juvenile mantle material and ancient crust provided sedimentary detritus. This is also consistent with the Nd isotopic signature of sedimentary rocks recorded in the Lengjiaxi Group, suggesting a back-arc tectonic setting. The Banxi Group has slightly enriched Nd isotopic signatures relative to the Lengjiaxi Group, implying a higher percentage of old continental material in the sedimentary source. Combined with previously published data, new results can help us to reconstruct the Neoproterozoic tectonic evolution of the South China craton. The age spectrum of detrital zircons and Nd-Hf isotopic composition suggests a two-stage collision: Between 1000 Ma to 870 Ma, a continental magmatic arc was build up along the eastern margin of the Yangtze block. Convergence led to continent-based back-arc extension, subsidence and formation of a back-arc basin. Detritus originating from arc-related magmatic and old basement rocks was transported into this back-arc basin resulting in formation of the Lengjiaxi Group and its equivalents. At around 870 Ma, a second (oceanic) arc was formed by extension of an inter-arc basin, subduction subsequently led to the first collision and the emplacement of the blueschist mélange. Accretion of the magmatic arc lasted until the closure of an oceanic basin between the Yangtze and Cathaysia blocks at about 830 Ma. Shortly after the collision, subsequent uplift, further extension of the former back-arc basin and post-collisional granitoid magmatism caused a tilting of the Lengjiaxi sediments. Between 830 Ma and 820 Ma, subsequent closure of the oceanic back-arc basin and formation of the Jiangnan orogen took place, leaving a regional unconformity above the Lengjiaxi Group. Above this unconformity the Banxi Group was immediately deposited during the post-tectonic stage.

阿尔泰南缘侧向增生过程中的VMS矿床：地质、地球化学特征与成矿机制

The Chinese Altai is one of the most important volcanogenic massive sulfide (VMS) deposit districts in China. All orebodies were lenticular or bedded and stratabounded by a suite of early Devonian volcanic-sedimentary rocks. Hydrothermal feeder zones developed under some of the orebodies. All the ores are massive or laminated, and show typical characteristics of VMS deposit. Based on the mineralizing time and the metal assembles, we divide 3 metallogenic stages: 1, Fe orefroming stage associated with basaltic and sedimentary rocks during very early Devonian; 2, Cu-Pb-Zn oreforming stage associated with rhyolitic and sedimentary rocks during early Devonian; 3， Cu-Zn oreforming stage in the dacitic and basaltic rocks during mid. Devonian. The hosting rocks for all orebodies are different, but they show very similar geochemical and isotopic characteristics. All the felsic rocks show enriched lighted rare earth elements (REE) patterns (La/Yb>5), and with an obvious Eu negative anomalies (Eu/Eu*<0.6). In the meanwhile, all the mafic rocks show flat REE pattern and no Eu anomalies. The Ashele basalt show an apparent Ce negative anomalies (Ce/Ce* <0.76), All the volcanic roks in Chinese Altai show the decoupled property between the high field strength elements (HFSE) and large ion lithophile elements (LILE). The negative Nb, Ta characteristics with respect to adjacent elements indicate that subduction-modified source. The Nd(t) of the hosting rocks for all orebodies changed in a small range (-1.5~5), and the (87Sr/86Sr)i change in a big range. The initial Sr value of the hosting rocks in Mengku and Tiemuerte are obviously affected by the seawater (0.705~0.710), and initial Sr values of hosting rocks Ashele change in a small range (0.704~0.706). All Sr-Nd isotopes of ores have the same range with the hosting rocks, indicating that both the ores and volcanic rocks have the same island arc source. The mean sulfur isotopes of sulfides from Ashele and Mengku are 6.2‰ and 3.4‰, respectively, indicating a deep magmatic source. However, the sulfur isotopes of sulfides from Keketale, Tiemuerte and Keyinbulake changed in -15.8‰~9.9‰, -23.5‰~1.87‰, -8.3‰~1.6‰, respectively. And the big sulfur isotope range indicated that the sulfur of the ores was a combination biogenic and magmatic source. All volcanic rocks from the VMS deposits in the southern Chinese Altai show a typical subduction related environments. Based on the regional and locally geological evidence, here we propose that the southern Chinese Altai is an island arc system, and all VMS deposits formed during the lateral accretion process. No VMS deposit formed during the formation of the island arc during Silurian; Fe VMS deposit formed during the beginning of the opening of the backarc basin in very early Devonian; Cu-Pb-Zn VMS deposits formed during the mature stage of the backarc basin in early Devonian; at last the Cu-Zn VMS deposit formed during the rifted stage of the island arc itself.

大别山碰撞造山带逆冲推覆构造运动学和动力学研究

Since the discovery of coesite-bearing eclogites in Dabie and Sulu region over ten years ago, the Dabie collisional orogen has been the "hot-spot" across the world. While many great progresses have been made for the last decade in the researches on the Dabie and Sulu UHP metamorphic rocks in the following fields, such as, petrology, mineralogy, isotope chronology, and geochemistry, the study of the structural geology on the Dabie orogen is still in great need. Thrust and nappe tectonics commonly developed in any collisional orogenic belt during the syncollisional process of the orogen. It is the same as the Dabic collisional orogen is concerned. The paper put much stress on the thrust and nappe tectonics in the Dabic orogenic belt, which have been seldom systematically studied before. The geometric features including the division and the spatial distribution of various thrust and nappe tectonics in the Dabie orogen have been first studied, which is followed by the detailed studies on their kinematic characteristics in different scales varying from regional tectonics to microtectonics. In the thesis, new deformation ages have been obtained by the isotopic methods of ~(40)Ar-~(39)Ar, Sm-Nd and Rb-Sr minerals-whole rock isochrons on the mylonites formed in three ductile shear zones which bounded three different major nappes in the Dabie collisional orogenic belt. And the petrological, geochemical characteristics of some metamorphic rocks as well as the geotectonics of their protoliths, which have also deformed in the ductile shear zone, are analyzed and discussed. In the paper, twelve nappes in the Dabie orogen are first divided, which are bounded by various important NWW or NW-strike faults and three NNE-strike faults. They are Shangcheng Nappe, Huoshan Nappe, Yuexi Nappe, Yingshanjian-Hengzhong Nappe, Huangzhen Nappe, Xishui-Huangmei Nappe, Zhoudang Nappe, Suhe-Huwan Nappe, Xinxian Nappe, Hong'an Nappe, Mulan Nappe and Hhuangpi-Susong Nappe. In the Dabie orogen, three types of thrust and nappe tectonics belonging to two stages have been confirmed. They are: (1) early stage ductile thrust -nappe tectonics which movement direction was top-to-the-south; (2) late stage brittle to ductile-brittle thrust-nappe tectonics which are characterized by double-vergence movement, including top-to-the-north and top-to-the-south; (3) the third type also belongs to the late stage which also characterized by double-vergence movement, including top-to-the-east and top-to-the-west, and related to the strike-slip movement. The deformation ages of both Wuhe-Shuihou ductile shear zone and Taihu-Mamiao ductile shear zone have been dated by ~(40)Ar-~(39)Ar method. ~(40)Ar/~(39)Ar plateau ages of biotite and mica from the mylonites in these two shear zones are 219.57Ma and 229.12Ma. The plateau ages record the time of ductile deformation of the ductile shear zones, which made the concerned minerals of the mylonites exhume from amphibolite facies to the middle-upper crustal conditions by the early stage ductile thrust-nappe tectonics. The mineral isochons of Sm-Nd and Rb-Sr dating on the same mylonite sample of the metamafic rocks are 156.5Ma and 124.56Ma respectively. The two isochron ages suggest that the mylonitic rock strongly deformed in the amphilbolite facies at 156Ma and then exhumed to the upper crustal green schist condition at 124Ma with the activities of the Quiliping-Changlinggang ductile shear zone which bounded to the southen edge of Xinxian Nappe. Studies of the petrological and geochemical characteristics of some meta-mafic rocks and discussion on the geotectonics of their protoliths indicate that their protoliths were developped in an island arc or back-arc basin or active continental margin in which calc-alkline basalts formed. This means that arc-accretion orogeny had evolved in the margins of North china plate and/or Yangtze plate before these two plates directly collided with each other during the evolution process of Dabie orogen. Three-stage evolution of the thrust-nappe tectonics in Dabie collisional orogen has been induced based on the above-mentioned studies and previous work of others. And a possible 3-stage exhumation model (Thrust-Positive Flower Structure Model) has also been proposed.

晚中生代松辽盆地形成的大地构造环境及成因机制

Directed by the theory of "Collision Tectonic Facies", the tectonic setting and dynamic mechanism of the formation of Songliao basin in late Mesozoic (J_3-K_1) are studied in the present thesis with the methods of petrology, petrochemistry, geochemistry and isotopic geochronology. The research contents in this paper include as followings. Firstly, the general tectonic frame is made up of different tectonic facies formed from Mid-late Proterozoic to Mesozoic, which are Huabei plate, the Chengde-Siziwangqi melange (Pz_1), the Wenduermiao magmatic arc (Pz_1), the Hegenshan-Chaogenshan melange (Pz_2), the accretion arec (Pz_1-P), the Raohe-Hulin melange (Mz), the magmatic arc (Mz) and the pull-apart basin on the magmatic arc (Mz). Secondly, the volcanic rock assemblages of Songliao basin and its adjacent area in late Mesozoic is the typical calc-alkaline of the magmatic arc. The types of volcanic rocks in the study area include basalts, basaltic andesites, andesites, dacites and rhyolites, and basic-intermediate volcanic rocks have higher alkalinity. The volcanic rock series in this area is the high-K calc-alkaline series. Thirdly, the total REE of volcanic rocks in Songliao basin and its adjacent area is higher than that of the chondrite. The pattern of the REE normalized by the chondrite shows the characteristics similar to that of the typical island arcs or the active continental margins in the earth, that is enrichment of LREE and depletion of Eu. The spider-diagram of the trace element normalized by the primitive mantle also expresses the similar features to that of the typical island arcs or the active continental margins, it has distinctive valleies of Nb, Ta, Sr, P, and Ti, as well as the peaks of La, Ce, Th, U, and K. The incompatible elements show that the high field strength elements, such as Nb, Ta, Ti, and P, are depletion while the low field strength elements, such as K, U, Pb, and Ba, are enrichment. These features are similar to those of orogenic volcanic rocks and imply the formation of the volcanic rocks in this area is related to the subduction. The degrees of both the enrichment of the HFS elements and depletion of the LFS elements become more obvious from basic to acid volcanic rocks, which suggests crustal contamination enhances with the magmatic crystallization and fractionation. The concentration of the compatible elements is W-shape, and anomalies in Cr and Ni suggest there is the contamination during the magmatic crystallization and fractionation. Fourthly, the isotopic age data prove the volcanic activity in the Songliao basin and its adjacent area started in the early-middle Jurassic, and ended in the end of the early Cretaceous-the beginning of the Cretaceous. The volcanism summit was the late Jurassic-the early Cretaceous (100 - 150Ma). Finally, the tectonic setting of volcanism in the late Mesozoic was magmatic arc, which originated the subduction of Raohe-Hulin trench to the northwest Asian plate. The subduction began in the middle Jurassic, and the collision orogenesis between the Sikhote-Alin arc and Asian continent was completed in the end of the early Cretaceous-the beginning of the late Cretaceous. The results of above tectonic processes were finally to format Nadanhada orogenic belt symbolized by the Raohe-Hulin suture or melange belt. The violently oblique movement of the Izanagi plate toward Asian plate in the late Mesozoic was the dynamic mechanism of above tectonic processes. At the same tome, the left-lateral strike-slip shear caused by the oblique movement of the Izanagi plate produced a series of strike-slip faults in east Asian margin, and the large scale displacements of these strike-slip faults then produced the pull-apart basing or grabens on the magmatic arc. Conclusively, the tectonic setting during the formation of the grabens of Songliao basin in the late Mesozoic was magmatic arc, and its dynamic mechanism was the pull-apart. In a word, there was a good coupling relation among the oblique subduction of the oceanic plate, collisional orogene between island arc and continental plate, strike-slip shear of the faults and the formation of the grabens in Songliao basin and its adjacent area in late Mesozoic. These tectonic processes were completed in the unoin dynamic setting and mechanism as above description.