油水两相管流流量测量研究

利用涡轮流量计测量了油水两相流动时的混合流量,重点研究了油相黏度变化和流量计入口油水相含率变化对测量精度的影响。实验采用了七种不同的油相黏度(50,160,225,400,700,1100,1450MPa?s),并在含油率0～100%范围内记录了292组不同油水混合流量下的测量值。研究结果表明,当油相黏度为低黏值50MPa?s和160MPa?s时,涡轮流量计的测量误差较小,且不受入口油相含率的影响,绝对误差均在±5%以内。当油相黏度大于225MPa?s时,随着入口油相含率的增加,误差逐渐增大。当油相黏度进一步提高到1100MPa?s以上时,涡轮流量计在较低的入口油相含率下进入非线性失效区。

超临界压力下航空煤油热裂解特性研究

本文介绍了大庆3号煤油在超临界条件下热裂解特性的实验研究。通过改进的煤油二级加热系统以及裂解产物收集和分析系统,研究了煤油在温度700-1100K,压力3.5-4.5MPa,以及驻留时间0.6/1/2.5s时的热裂解吸热特性。同时实验测量了裂解产物的成分以及裂解混合物的流量随温度、压力、驻留时间的变化。研究发现:裂解特性,如裂解度、化学热沉、裂解产物成分均随裂解温度、驻留时间显著变化,而受压力的影响不大。当裂解度大约45%时,裂解反应的化学热沉达到最大值,该值随着驻留时间的增大而减小。气相产物的成分分析结果表明随着裂解温度的升高和驻留时间的增大,产物中饱和烃的比重增加,因此反应的吸热能力明显减小。在目前的裂解条件下,可获得的最大化学热沉为0.5MJ/kg,小于美国JP-7燃料的最大热沉0.7MJ/kg(裂解度60%)。

油水两相流粘度变化对涡轮流量计测量影响的实验研究

利用涡轮流量计测量了油水两相流动时的混合速度,重点研究了油相粘度变化和流量计入口油水相含率变化对测量精度的影响。实验采用了七种不同的油相粘度(50,160,225,400,700,1100,1450mPa?s),并在含油率0-100%范围内记录了292组不同油水混合流量下的测量值。研究结果表明,当油相粘度为低粘值50和160mPa?s时,涡轮流量计的测量误差较小,且不受入口油相含率的影响,绝对误差均在±5%以内。当油相粘度大于225mPa?s时,随着入口油相含率的增加,误差逐渐增大。当油相粘度进一步提高到1100mPa?s以上时,涡轮流量计在较低的入口油相含率下进入非线性失效区。此外,实验数据还显示,用涡轮流量计测量油水混合流速时,测量结果对油水两相流流型不敏感.

微/纳米氧化锌（ZnO）的生长、性质及其应用研究

纳米氧化锌（ZnO）是一种直接宽带隙半导体材料，室温下其禁带隙宽为本3.37 eV，激子束缚能为60 meV。纳米ZnO有明显的尺寸效应、表面和界面效应等，物理化学性能优越。在压电材料、铁电材料、平面显示、表面声波、传感器、场发射器件、激光、光催化等方面有着广泛的用途。近年来，对纳米ZnO材料的研究成为国内外的一个热点。 本论文研究了用化学气相沉积（CVD）法制备微/纳米ZnO材料。通过控制实验条件，合成了多种特殊结构和形貌的微/纳米ZnO材料，并用扫描电子显微镜（SEM）、高分辨率透射电镜（HR-TEM）、X-射线衍射仪（XRD）、Raman光谱和光致发光（PL）等对材料的结构和光学性能进行了表征。采用CVD法，在温度为630 °C，氧气流量为15 sccm，氩气流量为300 sccm的条件下，制备了一种纳米带冠四足状ZnO（T-ZnO）。此结构ZnO材料的每根足顶端均有一规则的六方帽形结构，具有很大的比表面积。实验结果表明：合成的ZnO材料为纤维锌矿结构单晶，并且沿着(0001)方向生长；室温下的PL谱有两个激发峰，一个是在393 nm处相对较弱的近带紫外峰，另一个是在511 nm处强峰。而材料在600 °C下氧气中退火30 min后，511 nm附近的绿光激发辐射峰则基本消失了，这说明在511 nm处的绿光激发辐射峰可能是由于氧空位引起的。此外，通过改变实验条件，还得到了其他多种结构的微/纳米ZnO材料。 通过大量实验，找到了一种在低温下合成微/纳米ZnO材料的新方法，即水蒸气氧化法。用ZnI2作为锌源，水蒸气作为氧化剂，实验温度在300～500 °C范围内，大大低于通常CVD法的500～1500 °C。采用此法，用硅做基底，得到了一系列有趣的实验结果，大多数情况下ZnO纳米晶自组装成很规则的圆。而在瓷舟中收集到的纳米ZnO跟普通CVD法结果相似，可以得到锥状、棒状等结构的纳米晶，但其生长方式与硅基底上的有很大差别。此外，用水蒸气氧化法，还实现了ZnO纳米晶在碳纳米管（CNTs）上的直接生长，而且其PL性能增强，这可能是纳米ZnO和CNTs相互耦合的结果。在700 °C温度下，以锌粉和ZnI2作为锌源，用水蒸气作为氧化剂，在硅基底的正反面分别得到了纳米棒和纳米推子阵列。此外，还对水蒸气氧化法的化学反应机理进行了分析，实验结果证明：固态ZnI2在受热和一定真空度下先蒸发成ZnI2分子，ZnI2分子遇到水蒸气发生反应生成偶极ZnO分子，这些ZnO偶极分子在硅基底上通过静电力自组装成特殊的几何形状。 此外，还通过分子动力学模拟的方法，对材料的力学性能进行了研究，得到了ZnO的弹性常数和体弹性模量，模拟值跟其他研究人员的实验和模拟结果吻合得很好，并估出算了ZnO晶体的表面能和断裂韧性。 本论文还对制备材料的光催化性能进行了系统的研究，采用CVD法制备ZnO，对铬黑T（EBT）进行光催化降解实验。通过正交实验方法，得到了ZnO催化降解EBT的最佳工艺条件，即催化剂用量为5 g/L，光照强度为120 W，反应温度为20 °C，反应时间为120 min，EBT浓度为10 mg/L，溶液pH值为4。 在最佳实验条件下，20分钟内有95%的EBT被降解完，30分钟内则全部降解。因此，ZnO在EBT的降解中催化效率很高，在废水处理中具有潜在的应用前景。

Thermal cracking of aviation kerosene for scramjet applications

Thermal cracking of China No.3 aviation kerosene was studied experimentally and analytically under supercritical conditions relevant to regenerative cooling system for Mach-6 scramjet applications. A two-stage heated tube system with cracked products collection/analysis was used and it can achieve a fuel temperature range of 700-1100 K, a pressure range of 3.5-4.5 MPa and a residence time of approximately 0.5-1.3 s. Compositions of the cracked gaseous products and mass flow rate of the kerosene flow at varied temperatures and pressures were obtained experimentally. A one-step lumped model was developed with the cracked mixtures grouped into three categories: unreacted kerosene, gaseous products and residuals including liquid products and carbon deposits. Based on the model, fuel conversion on the mass basis, the reaction rate and the residence time were estimated as functions of temperature. Meanwhile, a sonic nozzle was used for the control of the mass flow rate of the cracked kerosene, and correlation of the mass flow rate gives a good agreement with the measurements.

Shape Optimization for Hypersonic Arc-Wing Missiles

National Natural Science Foundation of China (NO.90916013)

结构精修研究合成温度对LiFePO_4结构的影响

固相法合成具有橄榄石型结构的LiFePO_4晶体,合成温度分别为670、700、730℃.采用XRD结构精修对合成LiFePO_4的结构进行了研究.研究发现随着合成温度的变化,晶胞参数a、b和c发生变化,晶胞参数的变化是等比例的增加或减少.由于合成温度的变化,Fe-O八面体中Fe-O键长发生变化,Fe-O键长的变化将会使得Fe的3 d轨道能量发生变化.相对于合成温度670、730℃,在700℃合成的LiFePO_4晶体具有最大的锂离子扩散有效面积.

Effect of vacuum-induced coherence on lasing without inversion in an equispaced three-level ladder system

The effects of vacuum-induced coherence (VIC) on the properties of the absorption and gain of the probe field in an equispaced three-level ladder atomic system are investigated. It is found that lasing without inversion (LWI) is remarkably enhanced due to the effect of VIC in the case of the small incoherent pump rate.

Determination and analysis of the optical constants of thin films of nickel(II) and copper(II) hydrazone complexes by spectroscopic ellipsometry

Thin films of four nickel(II) and copper(II) hydrazone complexes, which will hopefully be used as recording layers for the next-generation of high-density recordable disks, were prepared by using the spin-coating method. Absorption spectra of the thin films on K9 optical glass substrates in the 300-700 nm wavelength region were measured. Optical constants (complex refractive indices N) and thickness d of the thin films prepared on single-crystal silicon substrates in the 275-675 nm wavelength region were investigated on a rotating analyzer-polarizer scanning ellipsometer by fitting the measured ellipsometric angles (Psi(lambda) and Delta(lambda)) with a 3-layer model (Si/dye film/air). The dielectric functions epsilon and absorption coefficients alpha as a function of the wavelength were then calculated. Additionally, a design to achieve high reflectivity and optimum dye film thickness with an appropriate reflective layer was performed with the Film Wizard software using a multilayered model (PC substrate/reflective layer/dye film/air) at 405 nm wavelength.

Yb:YAG/YAG复合陶瓷薄片连续和调Q输出特性

采用面泵浦的CAMIL结构，我们研究了970 nm泵浦的Yb:YAG/YAG复合陶瓷薄片激光器，获得了连续和调Q的激光输出。在连续运转情况下，获得了最高1.05 W的激光输出，中心波长为1031 nm，后腔输出镜透射率为2％。我们同时获得了声光调Q的脉冲输出，重复频率从1 kHz到30 kHz，脉宽分别从166 ns到700 ns。

Fabrication and emission properties of Er3+/Yb3+ codoped tellurite glass fiber for broadband optical amplification

Tellurite glass is proposed as a host for broadband erbium-doped fiber amplifiers because of their excellent optical and chemical properties. A new single mode Er3+/Yb3+ codoped tellurite fiber with D-shape cladding geometry is fabricated in this work. When pumped at 980 nm, a broad erbium amplified spontaneous emission (ASE) nearly 100 nm in the wavelength range of 1450-1650 ran around 1.53 mu m is observed. It was found that the emission spectrum from erbium in tellurite glass fibers is almost twice as broad as the corresponding spectrum in tellurite bulk glass. The changes in ASE with regard to fiber lengths and pumping power were measured and discussed. The output of about 2.3 mW from Er3+/Yb3+ codoped tellurite fiber ASE source is obtained under the pump power of 700 mW. The broad 1.53 mu m emission of Er3+ in Er3+/Yb3+ codoped tellurite glass fiber can be used as host material for potential broadband optical amplifier and tunable fiber lasers. (c) 2005 Elsevier B.V. All rights reserved.

石英玻璃表面金属沉积层的界面研究

就石英玻璃的金属化进行了初步研究，综合考虑石英玻璃管和金属的特点，合理选择金属化膜层；采用磁控溅射工艺在石英玻璃表面镀制薄膜，利用俄歇电子能谱（AES）进行了界面分析。发现膜层在沉积过程中有轻微的扩散和界面还原反应现象，后期的热处理使这种现象变得更加显著。600℃时界面扩散变得明显，Ni膜中Mo的含量达到了20％；800℃时界面扩散已经很严重，表层Ni膜渗过Mo膜进入到Ti层。因此在后期处理时，温度应控制在700℃左右。对样品灯进行了检验，加速寿命及灯头耐压检验结果均通过初步考核。

Inhomogeneous broadening, luminescence origin and optical amplification in bismuth-doped glass

Absorption and luminescence spectra and optical amplification in bismuth-doped germanate silicate glass were investigated. Two kinds of bismuth ion valence states could exist in the glass. One is Bi2+, which has shown red luminescence, another might be Bi+, which is the active center for infrared luminescence. The infrared luminescence excited at 700, 800, and 980 nm should be ascribed to the electronic transition P-3(1) --> P-3(0) of Bi+ ions in three distinct sites. The shifting, broadening, and multiple configuration of the luminescence could be due to the randomly disorder of local environment and multiple sites of the active centers. In this glass, obvious optical amplification was realized at 1300 nm wavelength when excited at 808 and 980 nm, respectively.

Novel Bi-doped glasses for broadband optical amplification

Broadband infrared luminescence is observed in various Bi-doped oxide glasses prepared by conventional melting-quenching technique. The absorption spectrum of the Bi-doped germanium oxide glass consists of five broad peaks at below 370, 500, 700, 800 and 1000 nm. The fluorescence spectrum exhibits a broad peak at about 1300 nm with full width at half maximum (FWHM) of more than 300 nm when excited by an 808 nm laser diode. The fluorescence lifetime at room temperature decreases with increasing Bi2O3 concentration. Influence of the glass composition and melting atmosphere on the fluorescence lifetime and luminescent intensity is investigated. The mechanism of the broadband infrared luminescence is suggested. The product of stimulated emission cross-section and lifetime of the Bi-doped aluminophosphate glass is about 5.0 X 10(-24) cm(2) s. The glasses might be promising for applications in broadband optical fiber amplifiers and tunable lasers. (c) 2007 Elsevier B.V. All rights reserved.

Two-photon excited red upconversion luminescence of thulium ions doped GeS2-In2S3-CsI glass

We report a novel phenomenon in GeS2-In2S3-CsI chalcohalide glass doped with Tm3+ ions. Under irradiation with an 808 nm laser diode, a bright red emission centered at 700 nm is observed for the first time in this glass. The log-log correlation between integrated emission intensity and pump power reveals that a two-photon absorption process is involved in the phenomenon, suggesting that the F-3(3,2) -> H-3(6) transition of Tm3+ ions is responsible for the appearance of the red emission. The results indicate that the indium (In) based chalcohalide glass containing Tm3+ ions is expected to find applications in visible lasers, high density optical storage and three-dimensional color displays. (C) 2009 Elsevier B.V. All rights reserved.