在33.4MeV/u~(17)N与~9Be反应中中子发射的起源

在不同角度测得的 33 4MeV/u17N +9Be反应中 ,发射中子的能谱具有复杂的形式 ,而且随着角度的增大显示出有规律的变化 发射中子至少来源于靶弹核间的核子 -核子碰撞、17N的破裂反应以及熔合热核的统计蒸发三种不同起源 分析结果表明 :反应体系三种起源的发射中子截面分别为 4 4 9,0 4 4和 5 5b

33轮SHACAL-2的差分非线性攻击

利用SHACAL-2的一个17轮差分非线性区分器,结合被猜测子密钥空间分割的方法和快速傅立叶变换,提出了一种攻击33轮SHACAL-2的新方法.该方法攻击33轮SHACAL-2需要244的选择明文、2496.6的33轮SHACAL-2加密和2502次算术运算,攻击成功概率为99%.与已有的结果相比较,新攻击有效地提高了单密钥下SHACAL-2的攻击轮数.

Crystal structure of microwave dielectric ceramics Ba[(Mg1-xCdx)(0.33)Nb-0.67]O-3

A series of complex perovskite solid solutions of Ba[(Mg1-xCdx)(0.33)Nb-0.67]O-3 have been synthesized by the columbite method. Detailed Rietveld refinement of their X-ray diffraction data show that Ba[(Mg1-xCdx)0(.33)Nb(0.67)]O-3 has an order trigonal structure. The ordering degree as determined by the B-site occupancies increases with the partial substitution of Cd for Mg.

Effect of substitution of chromium for nickel on structure and electrochemical characteristic of Ti0.26Zr0.07V0.24Mn0.1Ni0.33 multi-phase hydrogen storage alloy

Ti-Zr-V-Mn-Ni-based multi-component alloys demonstrate high discharge capacity in KOH electrolyte. However, the drastic decrease in their discharge capacities makes them unsuitable for use as negative electrode material in the Ni/MH battery. In present work, Ni is partially replaced by Cr in the Ti-Zr-V-Mn-Ni-based alloys to improve their cycle life. The effects of Cr substitution on microstructures and the electrochemical characteristics of the alloys are investigated. It is found that Cr substitution is very effective to improve the cyclic durability of the alloys although the discharge capacity decreases with changing x from 0.05 to 0.20. Some kinetic performances have been also investigated using electrochemical impedance spectroscopy (EIS) and potentiostatic discharge technique.

Microstructure, thermal stability and mechanical properties of the novel (W1-xAlx)C-Co (x=0.2, 0.33, 0.4, 0.5) cemented carbide

Bulk novel cemented carbides (W1-xAlx)C-10.1 vol% Co (x = 0.2, 0.33, 0.4, 0.5) are prepared by mechanical alloying and hot-pressing sintering. Hot-pressing (HP) is used to fabricate the bulk bodies of the hard alloys. The novel cemented carbides have good mechanical properties compared with WC-Co. The density and operating cost of the novel material is much lower than a WC-Co system. The material is easy to process and the processing leads to nano-scaled, rounded, particles in the bulk material. The hardness of (W1-xAlx)C-10.1 vol% Co (x = 0.2, 0.33, 0.4, 0.5) hard material is 20.37, 21.16, 21.59 and 22.16 GPa, and the bending strength is 1257, 1238, 1211 and 1293 MPa, with the aluminum content varying from 20% to 50%. The relationship between the microstructure and the mechanical properties of the novel hard alloy is also discussed.

微观结构对溶胶-凝胶法合成的La_(0.67)Sr_(0.33)MnO_3电磁性能影响

采用溶胶-凝胶法制备了不同烧结温度的钙钛矿类锰氧化物La0.67Sr0.33MnO3样品。实验结果表明,在1573 K以上烧结的样品,晶粒出现异常长大,晶界效应明显。随着烧结温度的提高,磁化强度逐渐增大,但样品的居里温度基本不变。此外,在1173和1573 K温度下烧结的样品,均出现了低于居里温度的金属-半导体导电行为转变。在合适的烧结条件下,可以观察到隧道磁电阻(TMR)和超大磁电阻(CMR)2种磁电阻效应。实验表明,自旋电子的输运,不仅与样品平均粒径的大小和密度有关,而且与晶界的微观结构有密切关系。

Synthesis, reactive mechanism and thermal stability of W1-xAlxC (x=0.33, 0.5, 0.75, 0.86) nanocrystalline

W1-xAlxC (x = 0.33, 0.50, 0.75, 0.86) solid solutions have been synthesized directly by ball-milling tungsten powder, aluminum powder and activated carbon. The structural development of W0.5Al0.5C phase with the milling times up to 160 h has been followed using X-ray diffraction. X-ray photoelectron spectra demonstrate that Al atom takes the place of W. High temperature annealing experiment reveals that Al is stable in hexagonal structure to 1873 K. Transmission electron microscopy image shows that the grain size of the prepared powders is about 5 nm.

The structure and electrochemical characteristics of La0.67Mg0.33 (Ni0.8Co0.1Mn0.1)(x) (x=2.5-5.0) multiphase alloys for nickel-metal hydride batteries

This paper presents results concerning structure and electrochemical characteristics of the La0.67Mg0.33 (Ni0.8Co0.1Mn0.1) (x) (x=2.5-5.0) alloy. It can be found from the result of the Rietveld analyses that the structures of the alloys change obviously with increasing x from 2.5 to 5.0. The main phase of the alloys with x=2.5-3.5 is LaMg2Ni9 phase with a PuNi3-type rhombohedral structure, but the main phase of the alloys with x=4.0-5.0 is LaNi(5)phase with a CaCu5-type hexagonal structure. Furthermore, the phase ratio, lattice parameter and cell volume of the LaMg2Ni9 phase and the LaNi5 phase change with increasing x. The electrochemical studies show that the maximum discharge capacity increases from 214.7 mAh/g (x=2.5) to 391.1 mAh/g (x=3.5) and then decreases to 238.5 mAh/g (x=5.0). As the discharge current density is 1,200 mA/g, the high rate dischargeability (HRD) increases from 51.1% (x=2.5) to 83.7% (x=3.5) and then decreases to 71.6% (x=5.0). Moreover, the exchange current density (I-0) of the alloy electrodes first increases and then decrease with increasing x from 2.5 to 5.0, which is consistent with the variation of the HRD. The cell volume reduces with increasing x in the alloys, which is detrimental to hydrogen diffusion and accordingly decreases the low-temperature dischargeability of the alloy electrodes.

Preparation, patterning and luminescent properties of oxyapatite La-9.33(SiO6)(4)O-2 : A (A = Eu3+, Tb3+, Ce3+) phosphor films by sol-gel soft lithography

Silicate oxyapatite La-9.33 (SiO6)(4)O-2:A (A = Eu3+, Tb3+ and/or Ce3+) phosphor films and their patterning were fabricated by a sol-gel process combined with soft lithography. X-ray diffraction (XRD), Fourier transform infrared spectroscopy, atomic force microscopy, optical microscopy and photoluminescence spectra, as well as lifetimes, were used to characterize the resulting films. The results of XRD indicated that the films began to crystallize at 800degreesC and the crystallinity increased with the increase in annealing temperatures. Transparent nonpatterned phosphor films were uniform and crack-free, which mainly consisted of rodlike grains with a size between 150 and 210 nm. Patterned thin films with different bandwidths (20, 50 mum) were obtained by the micromoulding in capillaries technique. The doped rare earth ions (Eu3+, Tb3+ and Ce3+) showed their characteristic emission in crystalline La-9.33(SiO6)(4)O-2 phosphor films, i.e. Eu3+ D-5(0)-F-7(J) (J = 0, 1, 2, 3, 4), Tb3+ D-5(3,4)-F-7(J) (J = 3, 4, 5, 6) and Ce3+ 5d (D-2)-4f (F-2(2/5), F-2(2/7)) emissions, respectively. Both the lifetimes and PL intensity of the Eu3+, Tb3+ ions increased with increasing annealing temperature from 800 to 1100 degreesC, and the optimum concentrations for Eu3+, Tb3+ were determined to be 9 and 7 mol% of La3+ in La-9.33(SiO6)(4)O-2 films, respectively. An energy transfer from Ce3+ to Tb3+ was observed in the La-9.33(SiO6)(4)O-2:Ce, Tb phosphor films, and the energy transfer efficiency was estimated as a function of Tb3+ concentration.

α-B-Keggin型杂多化合物K_5H[Co_4(VW_9O_(33))_2]·5H_2O的合成和结构

合成了新化合物K_5H[Co_4(VW_9O_(33))·5H_2O,并运用IR,UV-ViS,DTA和单晶X射线衍射对其结构进行了表征.测定结果证实标题化合物具有α-B-Keggin型结构,两个(VW_9O_(33)~(7-)结构单元由四个Co(Ⅱ)O_6 八面体连接.杂多化合物属单斜晶系P2_(1/n),a=1.2307(3)nm,b=2.1250(4)nm,c=1.5817(3)nm,β=91.86(3)°,V=4.1343(14)nm~3,R=0.0895,R_w=0.2180.

Ce~（3＋），Tb~（3＋）在Al_4B_2O_9和Al_（18）B_4O_（33）基质中的发光

采用固相反应法在Ａｌ２Ｏ３－Ｂ２Ｏ３体系中合成了Ａｌ４Ｂ２Ｏ９和Ａｌ１８Ｂ４Ｏ３３两个相关化合物，测定了在两种基质中Ｃｅ３＋，Ｔｂ３＋和Ｃｅ３＋－Ｔｂ３＋的光谱，观察到在两种基质中Ｃｅ３＋的光谱相似，Ｃｅ３＋的发射峰位置在Ａｌ１８Ｂ４Ｏ３３中比Ａｌ４Ｂ２Ｏ９稍有红移。实验表明，Ａｌ１８Ｂ４Ｏ３３将是一种好的发光基质

LIQUID-CHROMATOGRAPHY WITH ELECTROCATALYTIC DETECTION OF CYSTEINE, N-ACETYLCYSTEINE AND GLUTATHIONE BY A PRUSSIAN BLUE FILM-MODIFIED ELECTRODE

Chemically modified electrodes prepared by adsorbing prussian blue on a glassy carbon electrode are shown to catalyse the electro-oxidation of cysteine, N-acetylcysteine and glutathione in acidic media. The catalytic response is evaluated with respect to the potential scan rate, the solution pH, the concentration dependence, and other variables. Covering the electrode with Nafion(R) film improved the stability and reproducibility in liquid chromatography with electrochemical detection to the extent that repetitive sample injections produced relative standard deviations of less than 5% over several hours of operation. The limit of detection was 4 pmol for cysteine, 33 pmol for glutathione and 61 pmol for N-acetylcysteine.

n-C_(16)H_(33)NH_3X和(n-C_(16)H_(33)NH_3)_2MX_4的红外光谱研究

在室温和液氮温度下研究了(n-C_(16)H_(33)NH_3)_2MX_4(简称C_(16)MX)及其相应化合物n-C_(16)H_(33)NH_3X(简称C_(16)X)于4000～50cm~(-1)范围的红外光谱。结果表明,它们都形成N-H…X型氢键,氢键强度是C_(16)X大于C_(16)MX。后者氢键的强度是按Cl>Br>I的顺序递减。C_(16)MX的光谱性质可按金属离子性质分为Cu~(2+)(Cu~(2+)、Cd~(2+)、Mn~(2+))和Zn~(2+)(Zn~(2+)、Co~(2+))两组,阴离子配位多面体的形状对其光谱性质有明显影响。还比较了室温与低温下的远红外光谱,证明了M—X键是离子键。

Refining near-native protein-protein docking decoys by local resampling and energy minimization

How to refine a near-native structure to make it closer to its native conformation is an unsolved problem in protein-structure and protein-protein complex-structure prediction. In this article, we first test several scoring functions for selecting locally resampled near-native protein-protein docking conformations and then propose a computationally efficient protocol for structure refinement via local resampling and energy minimization. The proposed method employs a statistical energy function based on a Distance-scaled Ideal-gas REference state (DFIRE) as an initial filter and an empirical energy function EMPIRE (EMpirical Protein-InteRaction Energy) for optimization and re-ranking. Significant improvement of final top-1 ranked structures over initial near-native structures is observed in the ZDOCK 2.3 decoy set for Benchmark 1.0 (74% whose global rmsd reduced by 0.5 angstrom or more and only 7% increased by 0.5 angstrom or more). Less significant improvement is observed for Benchmark 2.0 (38% versus 33%). Possible reasons are discussed.