Formation of dendritic nanostructures in Pyrex glass anodically bonded to silicon coated with an aluminum thin film

Anodic bonding with thin films of metal or alloy as an intermediate layer, finds increasing applications in micro/nanoelectromechanical systems. At the bonding temperature of 350 degrees C, voltage of 400 V, and 30 min duration, the anodic bonding is completed between Pyrex glass and crystalline silicon coated with an aluminum thin film with a thickness comprised between 50 and 230 nm. Sodium-depleted layers and dendritic nanostructures were observed in Pyrex 7740 glass adjacent to the bonding interface. The sodium depletion width does not increase remarkably with the thickness of aluminum film. The dendritic nanostructures result from aluminum diffusion into the Pyrex glass. This experimental research is expected to enhance the understanding of how the depletion layer and dendritic nanostructures affect the quality of anodic bonding. (C) 2007 Elsevier B.V. All rights reserved.

Designing a coupler for the intersatellite optical communication system

Coupling a single-mode laser diode with 200 mW to a single-mode fiber (SMF) through an orthonormal aspherical cylindrical lens and a GRIN lens for the intersatellite optical communication system is proposed and demonstrated. We experimentally studied how the coupling efficiency changes with the SMF's position displacement and axial angle variation, and obtained 80 mW output power at the end of the SMF, which shows that the coupling units have satisfied the designed request. (c) 2007 Elsevier GmbH. All rights reserved.

大口径干涉仪装置的调整及支承机构

采用蜗轮蜗杆驱动调整机构、使用同步带安装标准镜片方式、正交十字导轨支撑等可有效提高光学精密检测系统中大口径干涉仪装置的镜面面形质量、稳定性和调节准确度，从理论上介绍了蜗轮蜗杆驱动机构等设计原理及其基本公式，并从实验上验证了这些机构对光学精密检测系统稳定性的影响．

高稳定高转换效率光参变放大器倍频抽运光源研究

为了实现光参变放大抽运光源高稳定输出的目的。通过对倍频过程的数值模拟分析，提出倍频中存在“稳定区”的概念，在基频光强一定的条件下（小于倍频晶体破坏阈值），通过非共线双程倍频的方式或串联倍频的方式可有效延长倍频晶体的有效作用长度，保证倍频工作区能够被控制在“稳定区”内，从而实现高稳定高转换效率的倍频输出。实验数据验证了这一结论，实验中，利用非共线双程倍频的方式使得倍频工作区在“稳定区”内，对波动±5．7％的1064nm高斯脉冲基频光，倍频光波动小于±2％，脉冲形状为高阶高斯脉冲，转换效率大于70％，实验结果

Optical properties of zirconia-titania-ORMOSIL films for temperature tuning distributed feedback waveguide lasers

The zirconia-titania-ORMOSIL waveguide thin films with considerable optical quality were prepared by the sol-gel process. The refractive index (n) and the extinction coefficient (k) were determined by a scanning ellipsometer. Wavelength tunable output of distributed feedback waveguide lasing was demonstrated in Rhodamine 6G doped ZrO2 TiO2-ORMOSIL thin films by varying the temperature, and about 5.5 nm wavelength tuning range was achieved around the emission wavelength of 599 nm. The thermal-optic coefficient (dn/dT) of the active ZrO2-TiO2-ORMOSIL films was deduced. (c) 2005 Elsevier B.V. All rights reserved.

飞秒激光辐照ZnO晶体

利用飞秒激光对ZnO晶体进行辐照，对辐照前后的晶体样品进行发光光谱及拉曼光谱检测。辐照后发光光谱的某些发光峰强度有明显增强，但未产生新的发光峰，表明没有新的缺陷结构产生，但晶体内锌空位、间隙位锌、间隙位缺陷浓度增加。拉曼光谱结果表明，辐照后ZnO晶体未产生相变，但随着辐照激光功率的增大，拉曼峰327 cm-1，437 cm-1强度明显减弱，表明在飞秒激光辐照作用下氧化锌的结晶程度下降。但574 cm-1峰值却随着辐照功率的增大而变大，分析表明该拉曼峰很可能是由于晶体内间隙位缺陷所致。同时实验过程中观察到飞

高光洁度玻璃基片的表面散射和体散射测量

提出了一种利用总积分散射（TIS）测量K9玻璃基片表面散射和体散射的实验方法。首先采用磁控溅射技术在基片表面沉积厚度为几十nm的金属Ag薄膜，然后将基片的表面和体区分开考虑，通过TIS测得了基片上下表面的均方根粗糙度。进而求得基片的总散射和表面散射．最后计算得到了体散射。分别利用TIS和原子力显微镜（AFM）测量了3个样品上表面所镀Ag膜的均方根粗糙度．两种方法所得的均方根粗糙度的数值相差不明显，差值分别为0．08，0．11和0．09nm，表明TIS和AFM的测量结果相一致。利用该方法测得3块K9玻璃基片