冲击压缩下玻璃等脆性材料中失效波的研究进展

失效波的研究始于Rasorenov和Kanel发现K19玻璃样品后自由表面速度时程曲线上有反常再压缩信号。失效波是二十世纪九十年代冲击动力学研究领域的一个重要发现，它是指在一维平面应变冲击压缩下，在玻璃等脆性材料中由冲击波引起的一种独特的失效或破坏现象。较为系统地回顾近年来对失效波的研究工作，评述了研究现状、最新结果、发展趋势、研究方法和实验手段，对尚存的问题进行了分析讨论，并介绍了玻璃材料的基本特性。最后简单汇报了作者在这方面的研究工作和取得的阶段性结果。

GCr15钢超高周疲劳行为的实验研究

以GCr15钢为实验材料进行旋转弯曲超高周疲劳行为的实验研究。用光学显微镜和扫描电镜对试样疲劳断口进行观察 ,结果显示 ,疲劳断裂周次从 10 6 直到 4× 10 8,GCr15钢疲劳裂纹大多起源于试样内部 ,裂纹源一般为非金属夹杂物。从内部起裂的试样 ,疲劳寿命一般比从表面起裂试样的寿命长。文中从断裂力学和断裂物理的角度 ,对实验结果和疲劳机理进行分析

多环环间混杂复合材料飞轮离心应力分析

采用平面应力假设,给出了计算多环环间混杂复合材料飞轮的离心应力和初始极限转速的方法,并采用二维轴对称的有限元分析验证了计算方法的合理性,可作为初步设计多环环间混杂复合材料飞轮的依据.本文的算例分析还表明,无论单一纤维或混杂的复合材料飞轮,空心结构的初始极限转速和储能密度均高于相应的实心结构的结果;且对于空心结构,有利于通过选择合适的混杂方案,实现一定意义上的"等强度"设计.

燃烧物理学基础

Laminar Burning Velocities and Markstein Lengths of Premixed Methane/Air Flames near the Lean Flammability Limit in Microgravity

Effects of flame stretch on the laminar burning velocities of near-limit fuel-lean methane/air flames have been studied experimentally using a microgravity environment to minimize the complications of buoyancy. Outwardly propagating spherical flames were employed to assess the sensitivities of the laminar burning velocity to flame stretch, represented by Markstein lengths, and the fundamental laminar burning velocities of unstretched flames. Resulting data were reported for methane/air mixtures at ambient temperature and pressure, over the specific range of equivalence ratio that extended from 0.512 (the microgravity flammability limit found in the combustion chamber) to 0.601. Present measurements of unstretched laminar burning velocities were in good agreement with the unique existing microgravity data set at all measured equivalence ratios. Most of previous 1-g experiments using a variety of experimental techniques, however, appeared to give significantly higher burning velocities than the microgravity results. Furthermore, the burning velocities predicted by three chemical reaction mechanisms, which have been tuned primarily under off-limit conditions, were also considerably higher than the present experimental data. Additional results of the present investigation were derived for the overall activation energy and corresponding Zeldovich numbers, and the variation of the global flame Lewis numbers with equivalence ratio. The implications of these results were discussed. 2010 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

板料激光弯曲试验

针对大飞机壁板用的铝合金板料AA6056进行激光弯曲过程的试验研究.试验选用厚度为1.0 mm和2.5 mm的薄板,采用多组不同的工艺参数进行对比分析.采用直径0.1 mm的镍铬.镍硅热电偶作为温度传感器,YOKOGAWA MV200型便携式记录仪测量板料表面的温度;使用MV.1300UM CCD拍摄板料激光弯曲变形的过程,通过自行开发的实时采集软件记录并进行图像处理,最终得到了板料激光弯曲变形过程的实测曲线.试验结果为该过程的数值模拟提供了更为精确的验证依据,为深入研究板料激光弯曲过程奠定了试验基础.

孔径光阑限制下高斯光束的传输

对高斯光束在硬边孔径限制下的衍射进行了详细的理论研究，就不同口径的圆孔限制下高斯光束在菲涅耳衍射区和夫琅禾费衍射区的分布进行了理论分析，从而得到了孔径受限高斯光束的横向以及轴向的衍射公式，进而对高斯光束在不同衍射区域内衍射光场分布形状随孔径尺寸变化时的演化规律进行了数值计算，并对小口径光阑受限的高斯光束的衍射与平行光经同尺寸光阑的衍射进行了比较。结果表明在较小口径下，两者的分布基本一致。得到的孔径光阑限制下高斯光束的传输规律为高斯光束在自由空间光通信和光学超分辨中的应用提供了理论基础。

Analysis on a new type magneto-optical disk for blue lasers

The conventional TbFeCo magneto-optical (MO) medium has a relatively smaller Kerr rotation angle in the blue region than in the red. With the recording wavelength gradually moving to the short wavelength, if TbFeCo is still used as recording medium, the conventional MO disk structure must be optimized to get a larger carrier to noise ratio (CNR). Sabi et al. have found that adding a metal layer attached to the TbFeCo film as thermal control layer is a useful way to get a high CNR. In this paper, we proved this through calculation, and carried out optimization of the new type of disk. Calculation results showed that the new structure is useful in preventing an excessive temperature increase, and has a better thermal response. (c) 2005 Elsevier B.V. All rights reserved.

输出5W的电光调Q Nd：YAG陶瓷激光器

研究了激光二极管（LD）侧向抽运的Nd：YAG陶瓷电光调Q激光器的激光输出特性。该激光器采用九组激光二极管线阵列（LDA）侧面紧密环绕均匀排布的抽运结构，并用微通道热汇冷却技术冷却。在电光调Q方式下，重复频率为100Hz，抽运单脉冲能量为416mJ时，用尺寸为庐5mm×75mm，掺杂原子数分数为1％的Nd：YAG陶瓷棒，获得50mJ的1064nm激光输出，脉冲宽度为12ns，斜率效率达24％。并实验测量和分析了偏振片，KD^＊P晶体，四分之一波片等调Q器件的插入损耗。测量了输出激光时间波形和光斑的光强空间

LD抽运的Nd：YLF／Cr^4＋：YAG被动调Q激光器

报道了激光二极管（LD）抽运的Nd：YLF激光器，采用平凹腔结构，分别用两片Cr^4＋：YAG可饱和吸收晶体，实现了被动调Q，输出激光波长为1053nm。采用厚度为0．5mm小信号透过率为90％的Cr^4＋ YAG，在泵浦功率最大为17W时，输出脉冲宽度为60．6ns，平均功率为1．5W，重复频率为9．5kHz，单脉冲能量为157．9mJ；采用厚度为0．55mm小信号透过率为95％的Cr^4＋ YAG，在泵浦功率最大为17W时，输出脉冲宽度为68．6ns，平均功率为1．35W，重复频率为14kHz，单脉冲

Ultrabroad infrared luminescences from Bi-doped alkaline earth metal germanate glasses

We report on ultrabroad infrared (IR) luminescences covering the 1000-1700-nm wavelength region, from Bi-doped 75GeO(2) 20RO-5Al(2)O(3) 1B(2)O(3) (R = Sr, Ca, and Mg) glasses. The full width at half-maximum of the IR luminescences excited at 980 nm increases (315 -> 440 -> 510 nm) with the change of alkaline earth metal (Mg2+ -> Ca2+ -> Sr2+). The fluorescence lifetime of the glass samples is 1725, 157, and 264 mu s when R is Sr, Ca, and Mg, respectively. These materials may be promising candidates for broad-band fiber amplifiers and tunable laser resources.

Surface morphology and properties of zirconia thin films prepared at different deposition rates

ZrO2 thin films were prepared on BK7 glass substrates by electron beam evaporation deposition method. The influence of deposition rate varying from 1.2 to 6.3 nm s(-1) on surface morphology and other properties of ZrO2 films were examined. With increasing deposition rate, the surface defect density increased. The decrease in half width at full maximum in X-ray diffraction pattern with deposition rate indicates an increase in crystal dimension with increasing deposition rate. Electron beam deposited ZrO2 films are known to be inhomogeneous. From the change of the peak transmittance value, it can be deduced that the inhomogeneity of ZrO2 films strengthened gradually with increasing deposition rate. The type of surface defects changed from nodules to craters when the deposition rate was high enough.

High-reflectance 193 nm Al2O3/MgF2 mirrors

Thin-film single layers of Al2O3 and MgF2 were deposited upon super polished fused-silica by electron-beam evaporation. The subsequent optical constants n and k were reported for the spectral range of 180-230 nm. High-reflectance dense multilayer coatings for 193 nm were designed on the basis of the evaluated optical constants and produced. The spectra of the reflectance of HR coatings were compared to the theoretical calculations. HR mirrors of 27 layers with a reflectance of more than 98% were reported. (c) 2004 Elsevier B.V. All rights reserved.