VCSEL-based parallel optical transmission module

This paper describes the design process and performance of the optimized parallel optical transmission module. Based on 1x12 VCSEL (Vertical Cavity Surface Emitting Laser) array, we designed and fabricated the high speed parallel optical modules. Our parallel optical module contains a 1x12 VCSEL array, a 12 channel CMOS laser driver circuit, a high speed PCB (Printed Circuit Board), a MT fiber connector and a packaging housing. The L-I-V characteristics of the 850nm VCSEL was measured at the operating current 8mA, 3dB frequency bandwidth more than 3GHz and the optical output 1mW. The transmission rate of all 12 channels is 30Gbit/s, with a single channel 2.5Gbit/s. By adopting the integration of the 1x12 VCSEL array and the driver array, we make a high speed PCB (Printed Circuit Board) to provide the optoelectronic chip with the operating voltage and high speed signals current. The LVDS (Low-Voltage Differential Signals) was set as the input signal to achieve better high frequency performance. The active coupling was adopted with a MT connector (8 degrees slant fiber array). We used the Small Form Factor Pluggable (SFP) packaging. With the edge connector, the module could be inserted into the system dispense with bonding process.

Subretinal implantable artificial photoreceptor

The present study reports a subretinal implant device which can imitate the function of photoreceptor cells. Photodiode (PD) arrays on the chip translate the incident light into current according to the intensity of light. With an electrode at the end of every photodiode, the PDs transfer the current to the remnant healthy visual cells such as bipolar cells and horizontal cells and then activate these cells. Biocompatible character of the materials and artificial photoreceptor itself were tested and the photoelectric characteristics of the chips in simulative condition were described and discussed.

Circuit design and simulation of a CMOS-based preamplifier for brain neural signals

A novel CMOS-based preamplifier for amplifying brain neural signal obtained by scalp electrodes in brain-computer interface (BCI) is presented in this paper. By means of constructing effective equivalent input circuit structure of the preamplifier, two capacitors of 5 pF are included to realize the DC suppression compared to conventional preamplifiers. Then this preamplifier is designed and simulated using the standard 0.6 mu m MOS process technology model parameters with a supply voltage of 5 volts. With differential input structures adopted, simulation results of the preamplifier show that the input impedance amounts to more than 2 Gohm with brain neural signal frequency of 0.5 Hz-100 Hz. The equivalent input noise voltage is 18 nV/Hz(1/2). The common mode rejection ratio (CMRR) of 112 dB and the open-loop differential gain of 90 dB are achieved.

Influence of mode symmetry on quality factors of degenerate states in microlasers with an equilateral triangle resonator

Modes in equilateral triangle resonator (ETR) are analyzed and classified according to the irreducible representations of the point group C-3v., Both the analytical method based on the far field emission and the numerical method by FDTD technique are used to calculate the quality factors (Q-factors) of the doubly degenerate states in ETR. Results obtained from the two methods are in reasonable agreement. Considering the different symmetry properties of the doubly degenerate eigenstates, we also discuss the ETR joined with an output waveguide at one of the vertices by FDTD technique and the Pade approximation. The variation of Q-factors versus width of output waveguide is analyzed. The numerical results show that doubly degenerate eigenstates of TM0.36 and TM0.38 whose wavelengths are around 1.5 mu m in the resonator with side-length of 5 mu m have the Q-factors larger than 1000 when the width of the output waveguide is smaller than 0.4 mu m. When the width of the output waveguide is set to 0.3 mu m, the symmetrical states that are more efficiently coupled to output waveguide have Q-factors about 8000, which are over 3 times larger than those of asymmetric state.

Diffractive Grating Based Out-of-Plane Coupling between Silicon Nanowire and Optical Fiber

Submitted by 阎军 (yanj@red.semi.ac.cn) on 2010-06-04T07:55:26Z No. of bitstreams: 1 Diffractive Grating Based Out-of-Plane Coupling between Silicon Nanowire and Optical Fiber.pdf: 232805 bytes, checksum: 0bd17756b8a703bf8337dd25bbddaca3 (MD5)

Demonstration of high efficient tunable lasing with one photonic crystal W1 waveguide

Submitted by 阎军 (yanj@red.semi.ac.cn) on 2010-06-04T08:18:15Z No. of bitstreams: 1 Demonstration of high efficient tunable lasing with one photonic crystal W1 waveguide.pdf: 564778 bytes, checksum: 1eb1246461d4a3fcc99e870bda90f9b4 (MD5)

A novel photonic crystal vertical cavity surface emitting laser based on coherent coupling

We demonstrate a novel oxide confined GaAs-based photonic crystal vertical cavity surface emitting laser (PC-VCSEL) operating at a wavelength of 850 nm based on coherent coupling. A ring-shaped light-emitting aperture is added to the conventional PC-VCSEL, and coherent coupling is achieved between the central defect aperture and the ring-shaped light-emitting aperture. Measurements show that under the continuous-wave (CW) injected current of 20 mA, a high power of 2 mW is obtained, and the side mode suppression ratio (SMSR) is larger than 20 dB. The average divergence angle is 4.2 degrees at the current level of 20 mA. Compared with the results ever reported, the divergence angle is reduced.

Slow Light Effect and Multimode Lasing in a Photonic Crystal Waveguide Microlaser

The slow light effect in a photonic crystal waveguide is investigated theoretically and experimentally. Theoretical calculation indicates that there is a slow light region for the even mode, from which the resonance and lasing in a microcavity would benefit. A photonic crystal waveguide microlaser is fabricated, which is related to the group velocity of c/120.6.

Control of the photonic crystal waveguide over the beam profile of vertical-cavity surface-emitting lasers

The control of the photonic crystal waveguide over the beam profile of vertical-cavity surface-emitting lasers is investigated. The symmetric slab waveguide model is adopted to analyze the control parameters, of the beam profile in the photonic-crystal vertical-cavity surface-emitting laser (PC-VCSEL). The filling factor (the ratio of the hole diameter to the lattice constant) and the etching depth control the divergence angle of the PC-VCSEL, and the low filling factor and the shallow etching depth are beneficial to achieve the low-divergence-angle beam. Two types of PC-VCSELs with different filling factors and etching depths are designed and fabricated. The experimental results show that the device with a lower filling factor and a shallower etching depth has a lower divergence angle, which agrees well with the theoretical predictions.

Single-mode holey vertical-cavity surface-emitting laser with ultra-narrow beam divergence

We demonstrated oxide-confined 850-nm vertical-cavity surface-emitting lasers (VCSELs) with a two-dimensional petal-shaped holey structure composed of several annular-sector-shaped holes. Four types of devices with different hole numbers were designed and fabricated. The measured results showed that the larger hole number was beneficial to purifying the lasing mode, and realizing the single-mode operation. The side mode suppression ratio (SMSR) exceeded 30 dB throughout the entire drive current. Mode selective loss mechanism was used to explain the single-mode characteristic. The single-mode devices possessed good beam profiles, and the lowest divergence angle was as narrow as 3.2 degrees (full width at half maximum), attributed to the graded index profile and the shallow etching in the top distributed Bragg reflector (DBR).

Phase-locked ring-defect photonic crystal vertical-cavity surface-emitting laser

Phase-locked oxide-confined ring-defect photonic crystal vertical-cavity surface-emitting laser is presented. The coupled-mode theory is employed to illustrate the two supermodes of the device, in-phase and out-of-phase supermode. Experimental results verify the two supermodes by the characteristics of the spectra and the far field patterns. At the lower current, only the out-of-phase supermode is excited, whereas under the higher current, the in-phase supermode also appears at the shorter wavelength range. In addition, the measured spectral separation between the two supermodes agrees well with the theoretical result.

Room temperature operation of photonic-crystal distributed-feedback quantum cascade lasers with single longitudinal and lateral mode performance

We demonstrate room temperature operation of photonic-crystal distributed-feedback quantum cascade lasers emitting at 4.7 mu m. A rectangular photonic crystal lattice perpendicular to the cleaved facet was defined using holographic lithography. The anticrossing of the index- and Bragg-guided dispersions of rectangular lattice forms the band-edge mode with extended mode volume and reduced group velocity. Utilizing this coupling mechanism, single mode operation with a near-diffractive-limited divergence angle of 12 degrees is obtained for 33 mu m wide devices in a temperature range of 85-300 K. The reduced threshold current densities and improved heat dissipation management contribute to the realization of devices' room temperature operation.

Design of surface emitting distributed feedback quantum cascade laser with single-lobe far-field pattern and high outcoupling efficiency

A 7.8-mu m surface emitting second-order distributed feedback quantum cascade laser (DFB QCL) structure with metallized surface grating is studied. The modal property of this structure is described by utilizing coupled-mode theory where the coupling coefficients are derived from exact Floquet-Bloch solutions of infinite periodic structure. Based on this theory, the influence of waveguide structure and grating topography as well as device length on the laser performance is numerically investigated. The optimized surface emitting second-order DFB QCL structure design exhibits a high surface outcoupling efficiency of 22% and a low threshold gain of 10 cm(-1). Using a pi phase-shift in the centre of the grating, a high-quality single-lobe far-field radiation pattern is obtained.

VLBI observations of a sample of 15 EGRET-detected AGNs at 5 GHz

We report VLBI observations of 15 EGRET-detected AGNs with European VLBI Network (EVN) at 5 GHz. All sources in the sample display core-jet structures.

The Kiloparsec-scale structure of 3C 286

We present radio images of the compact steep spectrum (CSS) quasar 3C 286 acquired with the Very Large Array (VLA) at 8.4 and 22.5 GHz. The source exhibits a two-sided core-jet structure with a bright central component and two extended components one to the east (P.A. 100degrees) and another to the southwest (P.A. -116degrees). From the compact core, an extension runs towards the southwest component up to similar to 0.7 arcsecond. The emission between the primary central component and the southwest component exhibits a knotty structure. A gradual change of the jet position angles from -135degrees to -120degrees in the inner southwest jet suggests a local bend. The position angle changes of the major eastern components E2 and E1 suggest that the eastern jet likely follows a curved trace. The bends in the jet trace may be associated with a relativistic precession or some interaction between the jet and the ambient matter. A mean spectral index of alpha(8.4)(22.5) similar to -0.76 (S-nu proportional to nu(alpha)) is estimated for the core component. Steep spectra are also obtained for the extended southwest component (2.6", P.A. -116degrees) and eastern component (0.8", P.A. 100degrees), with alpha(8.4)(22.5) similar to -0.88 and alpha(8.4)(22.5) similar to -1.79, respectively. The radio morphologies and spectral index distributions suggest that the core seen in our images is likely to be the beamed inner jet while the real nucleus is dimmed by it beaming away from us.