Influence of different substrates on laser induced damage thresholds at 1064 nm of Ta2O5 films

Ta2O5 films are prepared on Si, BK7, fused silica, antireflection (AR) and high reflector (HR) substrates by electron beam evaporation method, respectively. Both the optical property and laser induced damage thresholds (LIDTs) at 1064 nm of Ta2O5 films on different substrates are investigated before and after annealing at 673 K for 12h. It is shown that annealing increases the refractive index and decreases the extinction index, and improves the O/Ta ratio of the Ta2O5 films from 2.42 to 2.50. Moreover, the results show that the LIDTs of the Ta2O5 films are mainly correlated with three parameters: substrate property, substoichiometry defect in the films and impurity defect at the interface between the substrate and the films. Details of the laser induced damage models in different cases are discussed.

Laser induced damage threshold at 355 and 1064 nm of Ta2O5 films of different phases

Ta2O5 films are deposited on fused silica substrates by conventional electron beam evaporation method. By annealing at different temperatures, Ta2O5 films of amorphous, hexagonal and orthorhombic phases are obtained and confirmed by x-ray diffractometer ( XRD) results. X-ray photoelectron spectroscopy ( XPS) analysis shows that chemical composition of all the films is stoichiometry. It is found that the amorphous Ta2O5 film achieves the highest laser induced damage threshold ( LIDT) either at 355 or 1064 nm, followed by hexagonal phase and finally orthorhombic phase. The damage morphologies at 355 and 1064 nm are different as the former shows a uniform fused area while the latter is centred on one or more defect points, which is induced by different damage mechanisms. The decrease of the LIDT at 1064nm is attributed to the increasing structural defect, while at 355nm is due to the combination effect of the increasing structural defect and decreasing band gap energy.

355nm增透膜的设计、制备与性能

用热舟蒸发法结合修正挡板技术制备了355 nm LaF3/MgF2增透膜,并对部分样品进行了真空退火。采用Lambda 900光谱仪测试了增透膜的低反光谱和透射光谱,并考察了其光谱稳定性;使用脉冲8 ns的355 nm激光测试了增透膜的激光损伤阈值(LIDT);采用Normarski显微镜对增透膜的表面缺陷密度和破斑形貌进行了观察。实验结果表明,制备得到的增透膜的剩余反射率较低,光谱稳定性好;真空退火对增透膜的激光损伤阈值没有改善;增透膜的破环形貌为散点形式,结合破斑深度测试表明薄膜的破坏源于薄膜和基底界面的缺陷点。JGS1熔石英基底由于有好的表面状况、固有的高激光损伤阈值和以其为基底的增透膜具有更低的表面场强,使得其上的增透膜有更高的抗激光损伤能力。

HfO2的纯度对紫外多层膜反射率的影响

用辉光放电质谱法和二次离子质谱仪测定了两种HfO2材料及它们相应的单层膜中的杂质含量，结果发现，无论是在体材料中还是在用电子束蒸发技术沉积的材料单层薄膜中，ZrO2都是这两种HfO2材料中最主要的杂质。而且，这两种HfO2材料中Zr含量的差别远远大于Ti、Fe含量的差别，这说明Zr含量的差别正是引起两种HfO2膜层光学性能差别的原因。用这两种不同纯度的HfO2材料与同一纯度的SiO2材料组合，沉积形成266nm的紫外反射镜，实验结果表明这两种反射镜的反射率分别在99.85% 和 99.15%左右。这个结果与依据单层膜得出的光学常数所设计的结果符合的很好。

Investigation on thermal stability of TiO2 films for application at high temperature

The thermal stability of electron beam deposited TiO2 monolayers and TiO2/SiO2 high reflectors (HR) during 300 to 1100 degrees C annealing is studied. It is found that the optical loss of film increases with the increase in annealing temperature, due to the phase change, crystallisation and deoxidising of film. Scattering loss dominates the optical property degradation of film below 900 degrees C, while the absorption is another factor at 1100 degrees C. The increase in refractive index and decrease in physical thickness of TiO2 layer shift the spectra of HR above 900 degrees C. The possible crack mechanism on the surface of HR during annealing is discussed. Guidance for application on high temperature stable optical coatings is given.

High refractive index TiO2 film deposited by electron beam evaporation

The well known 'crystal seed' theory is first applied in this work to prepare TiO2 film: a high refractive index rutile TiO2 film is grown by electron beam evaporation on the rutile seed formed by 1100 degrees C annealing. The average n is larger than 2.4, by far the highest in all the authors' TiO2 films. The films are characterised by optical properties, microstructure and surface morphologies. It is found that the refractive index shows positive relation with the crystal structure, grain size, and packing density and roughness of the film. The film has lower density of granularity and nodule defects on the surface than those of the film deposited by magnetron sputtering. The result shows attractive application in complex filter and laser coatings.

Microfabries of lacustrine sediments to pollutant adsorption from a polluted Eutrophic lake, the Yangtze delta region

Two types of microfabrics relating to pollutant adsorption were studied in the scanning electronic microscope (SEM) in a polluted, eutrophic lake, the Yangtze delta region. Agglutinational texture or the aggregates of small particles are composed of clay minerals and fine organic fragments among the silty grains and the coatings with a thickness about 1 mu m were on the surfaces of the silty grains in the sediments. The chemical constituents of the aggregates and the coatings are K, Na, Ca, Mg, Si, Al, O, Fe, Ti, C, N and P determined in X-ray energy spectrometry connected with the SEM. In some cases, Pb was detected in the aggregates in the top sediment. It is suggested that nutrients and metals are adsorbed to the aggregates, which were formed by electrostatic attraction of physicochemical floes. The coatings on the surface of quartz grains were formed by the interaction of dissociated Al, Si, Fe, etc from silicates with dissolved N, P and C nutrients in interstitial water, which was aroused by human pollution to the lake in recent two decades.