Multiterawatt laser system based on optical parametric chirped pulse amplification

A compact multiterawatt laser system based on optical parametric chirped pulse amplification is demonstrated. Chirped pulses are amplified from 20 pJ to 900 mJ by two lithium triborate optical parametric preamplifiers and a final KDP optical parametric power amplifier with a pump energy of 5 J at 532 nm from Nd:YAG-Nd: glass hybrid amplifiers, After compression, we obtained a final output of 570-mJ-155-fs pulses with a peak power of 3.67 TW, which is the highest output power from an optical parametric chirped pulse amplification laser, to the best of our knowledge. (C) 2002 Optical Society of America.

钕玻璃、Nd：YAG和Nd：GGG热容激光特性比较

考虑固体热容激光器对工作介质的要求，对比分析了掺钕的玻璃、YAG和GGG的多种材料性能。并对三者在激光工作周期内的瞬态温度场及热应力进行了数值模拟。结果表明：在给定的边界及工作条件下，当钕玻璃激光器以热容方式工作，时间为5S时，介质最高升温超过400K，最大热致应力为25MPa，接近其断裂极限的50％。在此条件下进行冷却，当水温为283K时，需经过约120S才基本恢复到初始工作状态。而Nd：YAG和Nd：GGG两种介质在相同输入工作条件下，工作时间可达10S，且温度分布相对平坦，温差和热应力较小，经水冷约

高稳定激光二极管抽运Nd∶YLF再生放大器

设计并实现了一种放大纳秒激光脉冲的高稳定的激光二极管(LD)抽运Nd∶YLF再生放大器。为了获得高稳定的输出,再生放大器工作在饱和状态。此时,再生放大器输出稳定性最好,而且注入激光脉冲能量波动引起的输出激光脉冲波动被抑制。由于增益饱和效应,再生放大器输出脉冲出现时域波形失真,附加后缀脉冲能够减弱时域波形失真。放大器工作波长1053nm,工作频率1Hz。输入240pJ的3ns方波激光脉冲,输出激光脉冲能量4.2mJ,总增益大于107,不稳定度小于1%(均方根),方波扭曲1.33。为3ns方波激光脉冲引入其本身幅度0.75倍的后缀脉冲,输出激光脉冲方波扭曲由1.33降至1.17。

Highly stable, diode-pumped Nd : YLF regenerative amplifier

We present the design and experimental results for a diode pumped Nd:YLF regenerative amplifier applied to amplify a nanosecond laser pulse. Numerical simulation shows that the maximum output energy and the best stability can be obtained when the regenerative amplifier operates in a saturated mode for all pulse duration and temporal profiles. Using extra post-pulse is a good method to decrease the square-pulse distortion caused by gain saturation effect. The amplifier shows output energy of 4.2mJ with a total energy gain of more than 107 and output energy stability of better than 1% rms. When extra post-pulse is added, square-pulse distortion is decreased from 1.33 to 1.17 for the amplifier that is seeded with an optical pulse of 3 ns.

Subsurface damage of Nd-doped phosphate glasses in optical fabrication

We present a destructive method for detecting and measuring subsurface damage of Nd-doped phosphate glasses. An instrument based on the dimple method - a destructive method - was developed. Subsurface damage depth produced in each fabrication procedure was obtained. We extend the surface roughness-subsurface damage relation to Nd-doped phosphate glasses. The constant ratio of subsurface damage and surface roughness was obtained as well. We also analyse the relation of abrasive size and subsurface damage experimentally. From a measurement of the surface roughness or abrasive size, one can obtain an accurate estimate of the damage layer thickness that must be eliminated by polishing or subsequent grinding operations. (C) 2007 Elsevier GmbH. All rights reserved.

LD 侧面抽运Nd :YAG陶瓷激光器运转条件下归一化热参数优化理论及实验研究

The suppressing effect of laser extraction on the non-radiation transition process is taken into account when the heat model of gain media is developed. Based on the developed heat model, the heat generation in the operating LD side-pumped Nd: YAG ceramic lasers is quantified through using the normalized heating parameter, which can be deduced from the experimental results of the slope efficiency and the absorbed pumping power of the gain media. The main factors which influence on the heat generation are investigated by studying the normalized heating parameter, and the results show that the changes of the laser extraction efficiency, the beam overlap efficiency and the Nd3+ concentration will result in obvious variations of the normalized heating parameter. In this work, the laser extraction efficiency increases to 0.905 by the optimization of the transmission of the output coupling, and the normalized heating parameter decrease to 0.474, correspondingly.

钛宝石激光器端面抽运Nd：YAG陶瓷激光器热沉积理论和实验研究

通过热沉积系数研究在激光提取条件下掺杂原子分数为1.0%的Nd：YAG陶瓷激光器中热沉积问题.热沉积系数定义为热沉积功率与激光器输出功率之比.在理论分析基础上,通过测量激光器斜率效率来间接测定热沉积系数,实验测定的热沉积系数值为0.63.建立激光提取条件下Nd：YAG陶瓷发热模型,讨论了影响热沉积系数的主要因素.结果表明：热沉积系数对Nd：YAG陶瓷的辐射量子效率、交叠效率以及激光提取效率的变化非常敏感.为有效减少介质内热沉积,在激光器优化设计中交叠效率和激光提取效率是需要着重考虑的参数.所得结果可为进一

位相锁定来自同一侧面抽运Nd：YAG板条的两束激光

实验研究了腔内位相锁定来至一LAD侧面抽运的Nd：YAG板条的两束激光，输出镜面出现干涉条纹，获得1.13W的相干光，其组束效率达到64.9%，相干度约60%。实验中发现只需要一根作为滤波的金属丝放在离输出镜合适的位置都就能有效稳定干涉条纹，金属丝引起的损耗低于8%。

激光二极管端面抽运Nd∶YVO_4板条激光器及其热效应

激光器中激光介质采用板条状几何结构可以极大地降低它的热效应,但仍然需要进一步分析其影响,进而优化激光器效率。利用有限元分析方法分析了部分端面抽运的混合腔板条激光器中激光介质的热效应,计算的热透镜焦距与实测结果基本相符。分析了热效应对模式匹配的影响,分析结果对于优化激光器效率、改进谐振腔设计具有一定的参考价值。并在分析的基础上进行了混合腔实验,抽运功率为110 W时,获得连续输出激光功率41.5 W,光-光转换效率约38%,斜效率达58.8%,M2因子为非稳腔方向M2x=1.59,稳定腔方向M2y=1.55。

边缘泵浦被动调Q的Nd：YAG薄片激光器

文中报道了一台采用激光二极管部分边缘泵浦方式的高功率薄片激光器，晶体尺寸是1 mm×10 mm×60 mm。Cr4+：YAG被用来作为被动调Q晶体，在重复频率高于10kHz时，获得了脉宽10ns，平均功率70W，斜线效率为36\%的激光输出。通过控制泵浦光束直径的大小，我们在厚度方向得到了近似衍射极限的光束输出。整个激光器结构紧凑，大小为60 mm×174 mm×150 mm。

Nd-glass belt lasers with improved beam quality

Nd-doped phosphate glass belt lasers pumped by laser diodes are demonstrated. The Nd-glass belt with a large cross-section and a small Fresnel number is air-cooled to provide around 18-W continuous wave (CW) output power with a beam quality factor of My2

Mode properties of off-axis one-sided hybrid resonator for novel high average power dual-slab laser

A novel dual-slab laser with off-axis one-sided hybrid resonator is presented. The mode properties of the hybrid resonator are calculated using a fast Fourier transform method (FFT). The influence of wavefront distoration on the output beam quality is considered. Results indicate that the novel dual-slab laser is better than the normal dual-slab laser with off-axis one-sided hybrid resonator.

A kilowatt diode-pumped solid-state heat-capacity double-slab laser

A kilowatt diode-pumped solid state heat capacity laser is fabricated with a double-slab Nd:YAG. Using the theoretical model of heat capacity laser output laser characteristics, the relationships between the output power, temperature and time are obtained. The slab is 59 x 40 4.5mm(3) in size. The average pump power is 11.2kW, the repetition rate is 1kHz, and the duty cycle 20%. During the running time of 1s, the output energy of the laser has a fluctuation with the maximal output energy at 2.06J, and the maximal output average power is 2.06kW. At the end of the second, the output energy declines to about 50% compared to the beginning. The thermal effects can be improved with one slab cooled by water. The experimental results are consistent with calculation data.

Property studies of optical waveguide formed by 6.0 MeV carbon ion implantation into Nd : silicate glass

Nd:silicate glass was implanted at room temperature by 6.0 MeV C3+ ions with a dose of 2.0 x 10(15) ions cm(-2). A waveguide with thickness of about 6.3 mu m was formed. The prism-coupling method was used to observe the dark modes of the waveguide at 633 nm and 1539 nm, respectively. There are three dark modes at 633 nm, of which one is the enhanced-index mode. The propagation loss of the enhanced-index mode in the waveguide measured at 633 nm is 0.42 dB cm(-1) after annealing at 217 degrees C for 35 min. The reflectivity calculation method was applied to simulate the refractive index profiles in the waveguide. The mode optical near-field output at 633 nm was presented.