薄膜材料对TiO2基薄膜激光损伤阈值的影响

abstract {The optical property, structure, surface properties (roughness and defect density) and laser-induced damage threshold (LIDT) of TiO₂ films deposited by electronic beam (EB) evaporation of TiO₂ (rutile), TiO₂ (anatase) and TiO₂ + Ta₂O₅ composite materials are comparatively studied. All films show the polycrystalline anatase TiO₂ structure. The loose sintering state and phase transformation during evaporating TiO₂ anatase slice lead to the high surface defect density, roughness and extinction coefficient, and low LIDT of films. The TiO₂ + Ta₂O₅ composite films have the lowest extinction coefficient and the highest LIDT among all samples investigated. Guidance of selecting materials for high LIDT laser mirrors is given.}

Comparison of femtosecond and nanosecond laser-induced damage in HfO2 single-layer film and HfO2-SiO2 high reflector

HfO2 single layers, 800 run high-reflective (HR) coating, and 1064 ran HR coating were prepared by electron-beam evaporation. The laser-induced damage thresholds (LIDTs) and damage morphologies of these samples were investigated with single-pulse femtosecond and nanosecond lasers. It is found that the LIDT of the HfO2 single layer is higher than the HfO2-SiO2 HR coating in the femtosecond regime, while the situation is opposite in the nanosecond regime. Different damage mechanisms are applied to study this phenomenon. Damage morphologies of all samples due to different laser irradiations are displayed. (c) 2007 Optical Society of America.

Effect of SiO2 protective layer on the femtosecond laser-induced damage of HfO2/SiO2 multilayer high-reflective coatings

Two kinds of HfO2/SiO2 800 nm high-reflective (HR) coatings, with and without SiO2 protective layer were deposited by electron beam evaporation. Laser-induced damage thresholds (LIDT) were measured for all samples with femtosecond laser pulses. The surface morphologies and the depth information of all samples were observed by Leica optical microscopy and WYKO surface profiler, respectively. It is found that SiO2 protective layer had no positive effect on improving the LIDT of HR coating. A simple model including the conduction band electron production via multiphoton ionization and impact ionization is used to explain this phenomenon. Theoretical calculations show that the damage occurs first in the SiO2 protective layer for HfO2/SiO2 HR coating with SiO2 protective layer. The relation of LIDT for two kinds of HfO2/SiO2 HR coatings in calculation agrees with the experiment result. (c) 2006 Elsevier B.V. All rights reserved.

Optimization of thin-film design for multi-layer dielectric grating

Thin-film design used to fabricate multi-layer dielectric (MLD) gratings should provide high transmittance during holography exposure, high reflectance at use wavelength and sufficient manufacturing latitude of the grating design making the MLD grating achieve both high diffraction efficiency and low electric field enhancement. Based on a (HLL)H-9 design comprising of quarter-waves of high-index material and half-waves of low-index material, we obtain an optimum MLD coating meeting these requirements by inserting a matching layer being half a quarter-wave of Al2O3 between the initial design and an optimized HfO2 top layer. The optimized MLD coatings exhibits a low reflectance of 0.017% under photoresist at the exposure angle of 17.8 degrees for 413 nm light and a high reflectance of 99.61% under air at the use angle of 51.2 degrees for 1053 nm light. Numerical calculation of intensity distribution in the photoresist coated on the MLD film during exposure shows that standing-wave patterns are greatly minimized and thus simulation profile of photoresist gratings after development demonstrates smoother shapes with lower roughness. Furthermore, a MLD gratings with grooves etched into the top layer of this MLD coating provides a high diffraction efficiency of 99.5% and a low electric field enhancement ratio of 1.53. This thin-film design shows perfect performances and can be easily fabricated by e-beam evaporation. (c) 2006 Elsevier B.V. All rights reserved.

Influence of substrate temperature on properties of MgF2 coatings

Thermal boat evaporation was employed to prepare MgF2 single-layer coatings upon both JGS1 and UBK7 substrates at different substrate temperatures. Microstructure, transmittance and residual stress of these coatings were measured by X-ray diffraction, spectrophotometer, and optical interferometer, respectively. Measurement of laser induced damage threshold (LIDT) of the samples was performed at 355 nm, 8 ns pulses. The results showed that high substrate temperature was beneficial to crystallization of the film. Above 244 degrees C, the refractive index increased gradually with the substrate temperature rising. Whereas, it was exceptional at 210 degrees C that the refractive index was higher than those deposited at 244 and 277 degrees C. The tensile residual stresses were exhibited in all MgF2 films, but not well correlated with the substrate temperature. In addition, the stresses were comparatively smaller upon JGS1 substrates. A tendency could be seen that the LIDTs reached the highest values at about 244 degrees C, and the films upon JGS1 had higher LIDTs than those upon UBK7 substrates at the same temperature. Meanwhile, the damage morphologies showed that the laser damage of the coating resulted from an absorbing center at the film-substrate interface. The features of the damages were displayed by an absorbing center dominated model. Furthermore, the reason of the difference in LIDT values was discussed in detail. (C) 2007 Elsevier B.V. All rights reserved.

利用等效层的消偏振宽带减反膜设计

分析了倾斜入射条件下导致光学薄膜产生偏振的原因, 针对不同偏振态的等效导纳与等效相位进行了分析, 并计算了对称膜层在45°入射条件下不同偏振态的等效折射率与等效相位厚度, 采用等效层方法设计了光学性能良好的600～900 nm波段消偏振宽带减反膜。最后利用电子束蒸发技术制备了薄膜样品, 样品的光谱性能完全能够满足使用要求。其中在600～900 nm波段范围内, 平均反射率均小于1.38%, 反射率的偏振度均低于0.89％。另外, 通过对其理论及实验光学性能、角度敏感性、膜层厚度误差敏感性等方面的分析结果可

三硼酸锂晶体上1064 nm, 532 nm, 355 nm三倍频增透膜的设计

采用矢量法设计了三硼酸锂晶体上1064 nm、532 nm和355 nm三倍频增透膜,结果表明1064 nm、532 nm和355 nm波长的剩余反射率分别为0.0017％、0.0002％和0.0013％。根据误差分析,薄膜制备时沉积速率精度控制在＋5.5％时,1064 nm、532 nm和355 nm波长的剩余反射率分别增加至0.20％、0.84％和1.89％。当材料折射率的变化控制在＋3％时,1064 nm处的剩余反射率增大为0.20％,532 nm和355 nm处分别达0.88％和0.24％。与薄膜

光学薄膜膜厚自动控制系统的研究

介绍了一种利用光电极值法同时控制规整膜系和非规整膜系的方法,利用VC＋＋编写程序实现对光学监控信号的采集、处理及停镀点的自动判断,实现了规整膜系和非规整膜系膜层厚度的自动控制.并利用该膜厚自动控制系统实验制备了规整膜系和非规整膜系多层膜,实验结果表明：利用该系统镀制的薄膜重复性良好,且光谱曲线和理论光谱曲线吻合较好.该系统解决了非规整膜系的监控问题,由计算机控制膜层的停镀点,排除了人的主观因素对薄膜的性能及其制备的重复性产生的影响,提高了薄膜镀制的重复性和成品率.

LBO晶体上具有不同厚度过渡层的倍频增透膜的设计和制备

Design and preparation of frequency doubling antireflection coating with different thicknesses of interlayer were investigated for LiB₃O₅ (LBO) substrate. The design was based on the vector method. The thickness of the inserted SiO₂ interlayer could be changed in a wide range for the four-layer design with two zeros at 1064 and 532 nm. The coatings without any interlayer and with 0.1 quarter-wave (λ/4), 0.3 λ/4, 0.5 λ/4 SiO₂ interlayer were deposited respectively on LBO by using electron beam evaporation technique. All the prepared coatings with SiO₂ interlayer indicated satisfying optical behavior. This expanded our option for the thickness of an interlayer when coating on LBO substrate. The prepared films with SiO₂ interlayer showed better adhesion than that without any interlayer. The thickness of the interlayer affected the adhesion, the adhesion for the coating with 0.5 λ/4 SiO₂ interlayer was not as good as the other two.}

LBO晶体上1064，532nm倍频增透膜的镀制及性能分析

用电子束蒸发沉积方法在X切LBO（X-LBO）晶体上镀制了两种不同膜系结构的1064和532nm倍频增透膜，其中一种膜系结构为基底／ZrO2／Y2O3／A12O3／SiO2／空气，另一种为基底／0．5Al2O3／ZrO2／Y2O3／A12O3／SiO2／空气，两种膜系结构的主要差别在于有无氧化铝过渡层。测量了薄膜的反射率光谱曲线，发现两种增透膜在1064和532nm处的反射率均小于0．5％，实际镀制结果与理论设计曲线的差异主要是由材料折射率的变化引起的。且对样品在空气环境中进行了温度为473K的退火处理，

沉积温度对LaF3薄膜性能的影响

abstract {LaF₃ single-layer coatings were prepared by thermal boat evaporation at the deposition temperatures of 189, 255, 277 and 321°C respectively. The crystal structures of the coatings were characterized by X-ray diffraction (XRD). A spectrophotometer was employed to measure its transmittance. Moreover, refractive index, extinction coefficient and cut-off wavelength were obtained from the measured transmittance spectral curve. The residual stress was evaluated by the Stoney's equation and optical interferometer. Laser induce damage threshold (LIDT) was performed by a tripled Nd:YAG laser system. The results show that the crystallization status becomes better with the deposition temperature increasing. Correspondingly, the grain size also gets larger. Meanwhile, the coatings become more compact and the refractive index increases. However, the absorption of coatings seriously rises and the cut-off wavelength drifts to the long wave. In addition, the residual stress also increases and the intrinsic stress plays a determinant role in the coating. The LIDT of the coating also enhances at high temperature.}

渐变折射率薄膜的分层评价探讨

首先阐述了将渐变折射率薄膜细分为多层均匀薄膜的分层介质理论，接着给出了一种获得最佳分层数目的分层评价方法，最后以线性变化渐变折射率薄膜为例说明了如何优化获得渐变折射率薄膜的分层数目．研究发现：渐变折射率薄膜的分层数目与薄膜的厚度和薄膜的折射率变化快慢有关，在一定的折射率变化范围内，渐变折射率薄膜的分层数目随着薄膜厚度的增加先减小后增大．

真空室内金属杂质污染对光学薄膜性能的影响

真空室内金属粒子污染是降低激光薄膜性能的一个重要因素。采用高真空残余气体分析仪,对薄膜沉积过程中的气氛进行分析。发现由黄铜制作的加热灯架在工作时会分解出Zn,在这种条件下沉积薄膜,会使薄膜中掺入金属杂质,导致薄膜激光破坏阈值降低。采用表面分析技术对薄膜的组分进行分析,证实薄膜中锌杂质的存在。激光破坏实验证明,含有锌杂质的薄膜的破坏阈值明显降低。

沉积速率对热舟蒸发LaF3薄膜性能的影响

用热舟蒸发方法在不同的沉积速率下制备了LaF3单层膜,并对部分单层膜进行了真空退火。分别采用X射线衍射(XRD),Lambda 900 光谱仪和355 nm Nd∶YAG脉冲激光测试了薄膜的晶体结构、透射光谱和激光损伤阈值(LIDT),并通过透射光谱计算得到样品的折射率和消光系数。实验结果表明,增大沉积速率有利于LaF3薄膜的结晶和择优生长,可以提高薄膜的致密性和折射率,但薄膜的抗激光损伤能力有所下降;沉积速率太大,又会恶化薄膜的结晶性能,同时薄膜中产生大量孔洞,薄膜的机械强度降低,导致薄膜的折射率减小和

单脉冲飞秒脉冲激光对单层和高反光学薄膜的损伤

用电子柬蒸发的方法在BK7玻璃上制备了ZrO2单层膜和ZrO2／SiO2高反膜，利用掺Ti：sapphire飞秒激光系统输出的中心波长为800nm，脉宽为50fs的激光脉冲对这两种样品进行了激光损伤阈值测试．实验结果表明，ZrO2单层膜的阂值比ZrO2／SiO2高反膜的高；这与传统的纳秒脉冲激光的损伤情况相反．利用光离化和碰撞离化激发电子到导带，形成电子等离子体基本模型并对此现象进行了解释．同时，用显微镜对样品的损伤形貌进行了观测，对损伤的特点进行了表征．