节流器内液-固两相流固体颗粒冲蚀数值模拟

建立了考虑颗粒碰撞的颗粒冲蚀计算模型,该数学模型包括:在Eulerian坐标系下求解连续相流场;在Lagrangian坐标系下运用离散颗粒硬球模型求解颗粒碰撞;应用半实验关联式求解颗粒冲蚀速率。对水力加砂压裂施工中节流器内液-固两相流的固体颗粒运动和冲蚀特性进行了数值模拟。计算结果表明,固体颗粒密集于节流器入口到出口的一段狭长区域内,冲蚀速率随流体速度呈指数性变化。颗粒直径越大,冲蚀速率也越大。节流器内冲蚀最严重的位置发生在距离节流器出口上边缘10mm以内的局部区域。

压缩真空环境中无相互作用两量子比特系统的纠缠动力学

本文研究了压缩真空中无相互作用双原子的纠缠动力学特性。通过分析不同初始纠缠态的演化，发现压缩真空中纠缠原子失去纠缠的速度比在普通真空中更快，并且压缩越大纠缠衰减越快。可以用concurrence和可分性“距离”Lambda的时间演化来解释这种不同寻常的纠缠突然消失现象。

Ultrafast dynamics in ZnO thin films irradiated by femtosecond lasers

The damage morphologies, threshold fluences in ZnO films were studied with femtosecond laser pulses. Time-resolved reflectivity and transmissivity have been measured by the pump-probe technique at different pump fluences and wavelengths. The results indicate that two-phase transition is the dominant damage mechanism, which is similar to that in narrow band gap semiconductors. The estimated energy loss rate of conduction electrons is 1.5 eV/ps. (c) 2005 Elsevier Ltd. All rights reserved.

Thermal, structural and optical properties of NiOx thin films deposited by reactive dc-magnetron sputtering

The NiOx thin films were deposited by reactive dc-magnetron sputtering from a nickel metal target in Ar + O-2 with the relative O-2 content 5%. The as-deposited NiOx, thin films could represent a two-component system comprising crystalline NiO particles dispersed in an amorphous Ni2O3. Decomposition temperature of the as-deposited NiO, thin films was at about 263 degrees C. After annealed at 400 degrees C for 30 min in air, the surface morphology of the films became very rough due to the decomposition of the Ni2O3, leading to the changes of the optical properties of the NiO, thin films. The reflectivity of the films annealed at 400 degrees C was lower than that of the as-deposited one and the optical contrast was 52% at 405 nm. (c) 2006 Elsevier B.V. All rights reserved.

SbOx thin films used for write-once blue laser recording

SbOx thin films are deposited by reactive dc-magnetron sputtering from all antimony metal target in Ar+O-2 with the relative O-2 content 7%. It is found that the as-deposited films call represent a two-component system comprising amorphous Sb and amorphous Sb2O3. The crystallization of Sb is responsible for the changes of optical properties of the films. The results of the static, test show that the SbOx thin films have good writing sensitivity for blue laser beams and the recording marks are very clear and circular. High reflectivity contrast of about 41% is obtained at a writing power 6 mW and writing pulse width 300 ns. In addition, the films show a good stability after reading 10000 times.

Avian influenza virus infection induces differential expression of genes in chicken kidney

The pathogenic process of highly pathogenic avian influenza virus (HPAIV) infection is poorly understood. To explore the differential expression of kidney genes as a result of HPAIV infection, two cDNA libraries were constructed from uninfected and infected kidneys by suppression subtractive hybridization (SSH). Fifteen genes including IFN-stimulated genes (ISG12), lymphocyte antigen 6 complex locus E gene (LY6E), matrix Gla protein gene (MGP), lysozyme gene, haemopoiesis related membrane protein I gene, KIAA1259, MGC68696, G6pe-prov protein gene (G6PC), MGC4504, alcohol dehydrogenase gene (ADH), glutathione S-transferase gene (GST), sodium-dependent high-affinity dicarboxylate transporter gene (SDCT), Synaptotagmin XV (SytXV) and two novel genes were found significantly up-regulated or dramatically suppressed. Differential expression of these genes was further identified by Northern blot. Functional analysis indicated that the regulation of their expression might contribute to the pathogenic process of HPAIV infection. In contrast, the increased expression of three IFN-stimulated genes named ISG12, LY6E, and haemopoiesis related membrane protein 1 gene might reflect host defense responses. Further study showed that ISG12 protein failed to directly interact with NS1 protein of HPAIV which expressed simultaneously in the organs where HPAIV replication occurred, by use of BacterioMatch two-hybrid system. Therefore, our findings may provide new insights into understanding the molecular mechanism underlying the pathophysiological process of HPAIV infection in chicken. (c) 2007 Elsevier Ltd. All rights reserved.

Experimental investigation on TBAB clathrate hydrate slurry flows in a horizontal tube: Forced convective heat transfer behaviors

Tetra-n-butyl-ammonium bromide (TBAB) clathrate hydrate slurry (CHS) is one kind of secondary refrigerants, which is promising to be applied into air-conditioning or latent-heat transportation systems as a thermal storage or cold carrying medium for energy saving. It is a solid-liquid two phase mixture which is easy to produce and has high latent heat and good fluidity. In this paper, the heat transfer characteristics of TBAB slurry were investigated in a horizontal stainless steel tube under different solid mass fractions and flow velocities with constant heat flux. One velocity region of weakened heat transfer was found. Moreover, TBAB CHS was treated as a kind of Bingham fluids, and the influences of the solid particles, flow velocity and types of flow on the forced convective heat transfer coefficients of TBAB CHS were investigated. At last, criterial correlations of Nusselt number for laminar and turbulent flows in the form of power function were summarized, and the error with experimental results was within 20%.

Transient flow patterns and bubble slug lengths in parallel microchannels with oxygen gas bubbles produced by catalytic chemical reactions

Transient flow patterns and bubble slug lengths were investigated with oxygen gas (O-2) bubbles produced by catalytic chemical reactions using a high speed camera bonded with a microscope. The microreactor consists of an inlet liquid plenum, nine parallel rectangular microchannels followed by a micronozzle, using the MEMS fabrication technique. The etched surface was deposited by the thin platinum film, which is acted as the catalyst. Experiments were performed with the inlet mass concentration of the hydrogen peroxide from 50% to 90% and the pressure drop across the silicon chip from 2.5 to 20.0 kPa. The silicon chip is directly exposed in the environment thus the heat released via the catalytic chemical reactions is dissipated into the environment and the experiment was performed at the room temperature level. It is found that the two-phase flow with the catalytic chemical reactions display the cyclic behavior. A full cycle consists of a short fresh liquid refilling stage, a liquid decomposition stage followed by the bubble slug flow stage. At the beginning of the bubble slug flow stage, the liquid slug number reaches maximum, while at the end of the bubble slug flow stage the liquid slugs are quickly flushed out of the microchannels. Two or three large bubbles are observed in the inlet liquid plenum, affecting the two-phase distributions in microchannels. The bubble slug lengths, cycle periods as well as the mass flow rates are analyzed with different mass concentrations of hydrogen peroxide and pressure drops. The bubble slug length is helpful for the selection of the future microreactor length ensuring the complete hydrogen peroxide decomposition. Future studies on the temperature effect on the transient two-phase flow with chemical reactions are recommended.

Numerical simulation of a bubble rising in shear-thinning fluids

The motion of a single bubble rising freely in quiescent non-Newtonian viscous fluids was investigated experimentally and computationally. The non-Newtonian effects in the flow of viscous inelastic fluids are modeled by the Carreau theological model. An improved level set approach for computing the incompressible two-phase flow with deformable free interface is used. The control volume formulation with the SIMPLEC algorithm incorporated is used to solve the governing equations on a staggered Eulerian grid. The simulation results demonstrate that the algorithm is robust for shear-thinning liquids with large density (rho(1)/rho(g) up to 10(3)) and high viscosity (eta(1)/eta(g) up to 10(4)). The comparison of the experimental measurements of terminal bubble shape and velocity with the computational results is satisfactory. It is shown that the local change in viscosity around a bubble greatly depends on the bubble shape and the zero-shear viscosity of non-Newtonian shear-thinning liquids. The shear-rate distribution and velocity fields are used to elucidate the formation of a region of large viscosity at the rear of a bubble as a result of the rather stagnant flow behind the bubble. The numerical results provide the basis for further investigations, such as the numerical simulation of viscoelastic fluids. (C) 2010 Elsevier B.V. All rights reserved.

Experimental Investigation of Performance of a Miniature Direct Methanol Fuel Cell in Short-Term Microgravity

Experimental study of a liquid fed direct methanol fuel cell has been conducted in different gravity environments. A small single cell with 5 cm x 5 cm active area has single serpentine channel on the graphite cathode polar plate and 11 parallel straight channels on the graphite anode flow bed. Cell voltage and current have been measured and two-phase flow in anode channels has been in situ visually observed. The experimental results indicate that the effect of gravity on power performance of the direct methanol fuel cell is large when the concentration polarization governs fuel cells operation. Gravitational effect becomes larger at higher current density. Increasing methanol feeding molarity is conducive to weaken the influence of gravity on performance of liquid fed direct methanol fuel cells. Increasing feeding flow rate of methanol solution from 6 to 15 ml/min could reduce the size of carbon dioxide bubbles, while the influence of gravity still exist. Transport phenomena inside direct methanol fuel cells in microgravity is also analyzed and discussed.

用双流体模型模拟超声速气固两相流动

采用了双流体模型对JPL(Jet Propulsion Laboratory)喷管中气固两相流动以及超声速射流两相流动进行了数值模拟,并研究了可压缩两相流动中气相与颗粒的相互作用规律.自主开发的一般曲线坐标系下二维轴对称可压缩双流体程序Solve2D,对气相求解Navier-Stokes(N-S)方程组,采用k-ε湍流模型,颗粒相求解Euler方程组.对JPL喷管内的两相流场和湍流两相射流流场进行了数值模拟,研究了不同颗粒质量百分数以及不同颗粒直径时的气固两相流场的流动规律.

微重力气液两相流动与池沸腾传热

综述了近年来中国科学院微重力重点实验室(国家微重力实验室)完成的一系列微重力气液两相流动与池沸腾传热方面的地基实验、飞行实验和理论研究等方面获得的主要成果.在微重力气液两相流动方面, 提出了半理论Weber数模型用于预测微重力条件下气液两相弹一环状流转换, 并采用Monte Carlo方法, 针对气泡初始尺寸对泡一弹状流转换的影响进行数值研究.通过俄罗斯"和平号"空间站与IL-76失重飞机实验, 获得了微重力下的气液两相流型图, 与此同时在地面利用小尺度毛细管模型模拟了微重力气液两相流动特征.实验测量了微重力气液两相流压降, 并基于微重力流动特性建立了一个泡状流压降关联模型.在微重力池沸腾传热方面, 利用我国返回式卫星完成了两次空间实验, 其中, 第22颗返回式卫星搭载铂丝表面R113池沸腾实验采用控制温度的稳态加热方式, 而实践8号育种卫星搭载平面FC-72池沸腾实验则采用控制加热电压的准稳态加热方式.同时, 还进行了地面常重力和落塔短时微重力条件下的对比实验研究.观察到丝状加热表面微重力时轻微的传热强化现象, 而平板加热表面微重力核态池沸腾低热流时传热强化、高热流时传热恶化.微重力实验中观察到气泡脱落前存在横向运动现象, 据此分析了气泡行为与传热之间关系, 并提出了一个预测丝状加热表面气泡脱落直径的半理论模型.旨在对相关领域的进一步发展和空间两相流系统的应用提供数据及理论支持

微小卫星贮箱内两相流界面变形定位及控制管理

液化气推进技术是微小伴随卫星在轨飞行采用的一种新型推进技术. 微小伴星空间调姿、变轨过程需精确的推力控制, 因此必须了解卫星推进系统中推进剂的形位分布. 本文理论分析了空间微重力环境下液化气推进剂气/液界面的形位分布及变化, 并通过落塔实验验证了微重力环境下有效控制液体推进剂的管理方法.

Thermal analysis of microstructural evolution of Al2O3 surface modified layers

Solidification behavior and microstructural evolution of surface modified layers in plasma cladding technique are studied via numerical simulations. Both the coupling effect of temperature and solid volume fraction are considered in the proposed thermal analytical model, by which the transient temperature distributions are calculated and the shape of melting pool is determined. Furthermore, we perform microscopic thermal analysis on the nucleation and growth behaviors of ceramic hardening phases and dendrites, as well as the kinetics of related two-phase flow systems. By comparing with experimental observations, the evolution mechanisms of the morphology of Al2O3 ceramic hardening layer are explained. Based on the above results, a relationship among the scanning velocity of plasma stream, dendritic growth rate and the advancing speed of solid/liquid interface is found, and an energy criterion is proposed for predicting the pushing/engulfing transition of ceramic particles by grain growth fronts. (C) 2009 Elsevier B.V. All rights reserved.

人载脂蛋白APOA5的克隆表达纯化及相互作用蛋白研究

人类的载脂蛋白A5（apolipoprotein A5，APOA5）是一个新近发现的载脂蛋白家族成员。它在血浆中的含量比其他载脂蛋白低1-2个数量级，但能显著影响血浆三酰甘油水平，对血脂代谢具有重要意义，可以作为降血脂药物治疗中一个强有力的潜在靶标。 由于APOA5在血浆中含量低，直接从血浆中分离纯化很困难，国内一直没有报道简易可靠的纯化方法。为进一步研究APOA5的生物学特性，探讨其与TG代谢中的其它关键成分之间的相互关系，揭示其在脂类代谢相关疾病中的重要地位，必须有大量的蛋白和抗体用于基础研究。因此本研究首先利用基因工程技术，诱导表达纯化APOA5蛋白，免疫动物制备多克隆抗体，为进一步研究人肝脏细胞中APOA5的相互作用蛋白，研究APOA5蛋白在肝脏细胞中的功能奠定基础。 为了深入研究APOA5在肝脏中如何行使功能，我们采用细菌双杂交技术寻找与APOA5相互作用的蛋白因子。并采用Pull-down技术，免疫荧光及免疫共沉淀技术进一步确证其在体外和体内的相互作用关系，为进一步阐明APOA5在体内的生理功能提供了新的线索。 第一部分 APOA5基因的克隆、原核表达、纯化及其多克隆抗体的制备 本研究首先应用基因克隆技术，从人肝癌细胞系SMMC-7721的cDNA中扩增出1.1 kb的ApoA5基因全长序列。然后将其克隆至表达载体pThioHisD，构建原核表达载体pTH-APOA5。该重组质粒转化至大肠杆菌 BL21（DE3），成功实现人APOA5融合蛋白在大肠杆菌中的表达。经发酵得到高效表达的融合蛋白。 融合蛋白在 IPGT 诱导下以包涵体的形式大量表达。利用融合蛋白上的一段组氨酸序列，用镍离子亲和柱进行纯化和复性后，获得较高纯度的人APOA5融合蛋白。利用该融合蛋白免疫新西兰大耳白兔，获得了高效价的兔抗人APOA5多克隆抗体，Western Blot结果显示此多克隆抗体与APOA5特异性结合。 第二部分 细菌双杂交筛选与APOA5相互作用的蛋白 本实验首先构建了pBT-APOA5重组质粒，经双酶切、PCR和测序鉴定证明重组诱饵质粒构建成功，并进行了表达、自激活鉴定。Western Blot鉴定证实报告菌株中表达了分子量为 68 kD左右的重组融合蛋白，与预测的分子量APOA5（41 kD）/lamda cI （27 kD）一致。自激活实验证明诱饵蛋白不能单独激活报告基因，可用于筛选人肝脏cDNA文库。经过双重抗性筛选和回复筛选，分离出10个阳性克隆。对结果进行生物信息学分析，得到7个与APOA5相互作用的蛋白，其中BI1为细胞凋亡调节因子；ATP6、CYTB、ND2、COX-1为线粒体表达蛋白； ALB、TTR为血清蛋白。 第三部分 APOA5与BI1相互作用的确证 首先构建了BI1的原核表达载体pGEX-5X-3-BI1，利用Pull-down实验检测了APOA5与BI1在体外具有相互作用。然后构建了BI1的真核表达载体pCDNA3.1-HA-BI1和APOA5的真核表达载体pCDNA3.1-APOA5，并验证其表达。通过免疫荧光细胞内共定位研究发现，靶蛋白APOA5主要分布于胞浆，与BI1在HEK293细胞有共定位，即APOA5与BI1存在相互作用的可能。最后利用免疫共沉淀手段，在HEK293细胞中确证了靶蛋白APOA5与BI1在体内的相互作用。 上述研究结果，为深入研究APOA5在体内的生物学功能提供了新的思路。 Apolipoprotein A5 (APOA5) is a newly discovered protein belongs to apolipoprotein family. APOA5’s concentration is 1-2 orders of magnitude lower than other apolipoproteins in the circulation. APOA5 significantly affected plasma triglyceride levels, which is important on lipid metabolism. APOA5 has strong potential to be used as a hypolipidemic drug target. Large amount of APOA5 protein and antibodies are needed in basic research, such as biological characteristics study of the APOA5, its relationship with other key components in TG metabolism, its role played in Lipid metabolism-related diseases. Due to its low concentration in plasma, separation and purification of APOA5 from the plasma is very difficult. Until now no report on simple and reliable method for purification has been published in China. In this study, we firstly got APOA5 recombinant protein using genetic engineering technology. The purified recombinant protein was used to immunize rabbits to get antiserum. It is important for further study of the APOA5 protein-interacting protein. And it lays the foundation for studing APOA5 function in liver. In order to study APOA5 function in liver, we used bacterial two-hybrid technology to find the APOA5 protein interactor. Pull-down, immunofluorescence and immunoprecipitation techniques were used to further confirm the interaction between APOA5 with its interactor in vitro and in vivo. All of these stdudies provided new clues on its physiological functions in vivo. Part I: Cloning, prokaryotic expression, purification and polyclonal antibody preparation of APOA5 First of all, we amplified APOA5 CDS sequence from the human hepatoma cell line SMMC-7721, and subcloned into Expression vector pThioHisD, and got the recombinants named pTH-APOA5. The plasmid was transformed to BL21 (DE3). E. coli BL21(DE3) cells bearing the pTH-APOA5 plasmid were cultured and APOA5 protein synthesis was induced by the addition of IPTG. Recombinant protein was expression in the form of inclusion. Inclusion bodies were dissolved in phosphate-buffered saline containing 8 M urea and 40 mM imidazole, then applied to a Ni2+ affinity column, and were eluted in a buffer containing 4 M urea and 200 mM imidazole. Fractions containing the APOA5 protein were pooled and dialyzed against buffer containing phosphate-buffered saline. Antiserum to recombinant human APOA5 was generated by immuning rabbit. Western Blot showed that this antiserum specific binding with APOA5. Part II Two-hybrid system screening protein interactions with the APOA5 The coding sequence of human APOA5 was amplified using synthetic oligonucleotide primers from pTH-APOA5 vector and was subcloned into the pBT plasmidc to yield pBT-APOA5 vector. DNA sequencing was performed to verify that no unwanted mutations occurred during the process of plasmid vector construction. We verified recombinant protein expression and tested self-activation by pBT-APOA5 prior to screening. Western Blot verified inducing a 68 kD band, consistent with the predicted molecular weight (APOA5 41 kD, lamda cI 27 kD). pBT-APOA5 can be used for screening human liver cDNA library because it can not self-activation. Totally 10 positive clones were isolated. The nucleotide sequence of the positive clones were determined and compared to NCBI nucleotide sequence databases. We got 7 protein which interact with APOA5, included BI1(Apoptosis regulator); ATP6, CYTB, ND2, COX-1(Mitochondrial protein) and ALB, TTR(Serum protein). Part III Confirming of interaction between APOA5 with BI1 pGEX-5X-3-BI1 vector was subcloned at first. Pull-down experiments were used to detect the interaction between APOA5 with BI1 in vitro. Later, pCDNA3.1-HA-BI1 and pCDNA3.1-APOA5 were subcloned. Through immunofluorescence co-localization study, we found APOA5 mainly distributed in the cytoplasm. APOA5 is co-localization with BI1 in HEK293 cells. Finally, we verified interaction between APOA5 with BI1 in vivo through immunoprecipitation.