华南地壳岩石弹性和变形性质的高温高压实验研究

The South continent of China lies to southeast of Eurasia block. It is an active area from the view of crust growth and continent spread and is a transition zone between continental crust and oceanic crust. The compressional wave velocities and anisotropies of typical crustal metamorphic rocks were determined at high temperature (up to 1000 ℃) and high pressure(up to 800MPa). The experimental results show that the velocities generally increase with pressure, and is unaffected by temperature up to around 550 ℃. But the velocities of all experimental samples start to drop above a temperature point. For an example, this greatly reduce the speed of wave propagation in amphibolite and serpentinite above 760 ℃ and above 550 ℃ respectively, which may be due to dehydrate of amphibole and serpentine. P-wave anisotropy coefficients of those rocks range from 2% to 10% at 800MPa and 500 ℃. The anisotropies decrease with increasing pressure at room temperature, but hardly change as function of temperature at constant 800MPa or 600MPa pressure. The average velocity of the six crustal rocks is 6.28km/s under the condition of 800MPa and 550 ℃, which is consistent with the result of deep seismic sounding data. Based on this experimental result, we deduce there may exist a lot of felsic granulites and amphibolites at the depth of 15-25km underground. With increasing temperature and pressure, the deformation behavior of the rocks undergoes from localized brittle fracture, semi-brittle deformation (cataclastic flow or semi-brittle faulting, semi-brittle flow) to homogeneous crystal-plastic flow. This transition is associated with mechanical behavior and micro-mechanism. It is very important to understanding earthquake source mechanics, the strength of the lithosphere and the style of deformation. The experiments were conducted at temperature of 600-1000 ℃, confining pressure of 500MPa, and stain rates of 10~(-4)-10~(-6) S~(-1). For fine-grained natural amphibolite, the results of experiments show that brittle faulting is major failure mode at temperature <600 ℃, but crystal-plastic deformation is dominate at temperature >800 ℃, and there is a transition with increasing temperature from sembrittle faulting to cataclastic flow and sembrittle flow at temperature of 670-750 ℃. For medium-grained natural Felsic granulite, the results of experiments show that brittle faulting is major failure mode at temperature <500 ℃, but crystal-plastic deformation is dominate at temperature >700 ℃, and there is a transition with increasing temperature from semibrittle faulting to cataclastic flow and sembrittle flow at temperature of 500-600 ℃.

东海陆架盆地西南部烟囱构造与油气运聚关系研究

In recent years, chimney structure has been proved one of important indicators and a useful guide to major petroleum fields exploration through their exploration history both at home and abroad. Chimney structure, which has been called "gas chimney" or "seismic chimney", is the special fluid-filled fracture swarm, which results from the boiling of active thermal fluid caused by abruptly decreasing of high pressure and high temperature in sedimentary layers of upper lithosphere. Chimney structure is well developed in continental shelf basin of East China Sea, which indicates the great perspectives of petroleum resources there. However, the chimney structure also complicated the petroleum accumulation. So the study of chimney structure on its formation, its effect on occurrence and distribution of petroleum fields is very important not only on theoretical, but also on its applied research. It is for the first time to make a clear definition of chimney structure in this paper, and the existence and practical meaning of chimney structure are illustrated. Firstly, on the viewpoint of exploration, this will amplify exploration area or field, not only in marine, but also on continent. Secondly, this is very important to step-by-step exploration and development of petroleum fields with overpressure. Thirdly, this will provide reference for the study on complex petroleum system with multi-sources, commingled sources and accumulation, multi-stage accumulations, and multi-suits petroleum system in the overlay basin. Fourthly, when the thermal fluid enters the oceanic shallow layer, it can help form gas hydrate under favorable low-temperature and high-pressure conditions. Meanwhile, the thermal fluid with its particular component and thermal content will affect the physical, chemical and ecological environments, which will help solving the problem of global resources and environment. Beginning from the regional tectonic evolution characteristics, this paper discussed the tectonic evolution history of the Taibei depression, then made an dynamical analysis of the tectonic-sedimentary evolution during the Mesozoic and Cenozoic for the East China Sea basin. A numerical model of the tectonic-thermal evolution of the basin via the Basin-Mod technique was carried out and the subsidence-buried history and thermal history of the Taibei depression were inverse calculated: it had undergone a early rapid rift and sag, then three times of uplift and erosion, and finally depressed and been buried. The Taibei depression contains a huge thick clastic sedimentary rock of marine facies, transitional facies and continental facies on the complex basement of ante-Jurassic. It is a part of the back-arc rifting basins occurred during the Mesozoic and Cenozoic. The author analyzed the diagenesis and thermal fluid evolution of this area via the observation of cathodoluminescence, scanning electron microscope and thin section, taking advantage of the evidences of magma activities, paleo-geothermics and structural movement, the author concluded that there were at least three tectonic-thermal events and three epochs of thermal-fluid activities; and the three epochs of thermal-fluid activities were directly relative to the first two tectonic-thermal events and were controlled by the generation and expulsion of hydrocarbon in the source rock simultaneously. Based on these, this paper established the corresponding model between the tectonic-thermal events and the thermal-fluid evolution of the Taibei Depression, which becomes the base for the study on the chimney structures. According to the analyses of the gas-isotope, LAM spectrum component of fluid inclusion, geneses of CO_2 components and geneses of hydrocarbon gases, the author preliminarily verified four sources of the thermal fluid in the Taibei Depression: ① dehydration of mud shale compaction, ② expulsion of hydrocarbon in the source rock; ③ CO_2 gas hydro-thermal decomposition of carbonatite; ④magma-derived thermal fluid including the mantle magma water and volatile components (such as H_2O, CO_2, H_2S, SO_2, N_2 and He etc.). On the basis of the vitrinite reflectance (Ro), homogenization temperature of fluid inclusion, interval transit time of major well-logging, mud density of the wells, measured pressure data and the results of previous studies, this paper analyzed the characteristics of the geothermal fields and geo-pressure fields for the various parts in this area, and discussed the transversal distribution of fluid pressure. The Taibei depression on the whole underwent a temperature-loss process from hot basin to cold basin; and locally high thermal anomalies occurred on the regional background of moderate thermal structure. The seal was primarily formed during the middle and late Paleocene. The overpressured system was formed during the middle and late Eocene. The formation of overpressured system in Lishui Sag underwent such an evolutionary process as "form-weaken-strengthen-weaken". Namely, it was formed during the middle and late Eocene, then was weakened in the Oligocene, even partly broken, then strengthened after the Miocene, and finally weakened. The existence of the thermal fluid rich in volatile gas is a physical foundation for the boiling of the fluid, and sharply pressure depletion was the major cause for the boiling of the fluid, which suggests that there exists the condition for thermal fluid to boil. According to the results of the photoelastic simulation and similarity physical experiments, the geological condition and the formation mechanism of chimnestructures are summarized: well compartment is the prerequisite for chimney formation; the boiling of active thermal fluid is the original physical condition for chimney formation; The local place with low stress by tension fault is easy for chimney formation; The way that thermal fluid migrates is one of the important factors which control the types of chimney structures. Based on where the thermal fluid come from and geometrical characteristics of the chimney structures, this paper classified the genetic types of chimney structures, and concluded that there existed three types and six subtypes chimney structures: organic chimney structures generated by the hydrocarbon-bearing thermal fluid in middle-shallow layers, inorganic and commingling-genetic chimney structures generated by thermal fluid in middle-deep layers. According to the seismic profiles interpretations, well logging response analysis and mineralogical and petrological characteristics in the study area, the author summarized the comprehensive identification marks for chimney structures. Especially the horizon velocity analysis method that is established in this paper and takes advantage of interval velocity anomaly is a semi-quantitative and reliable method of chimney structure s identification. It was pointed out in this paper that the occurrence of the chimney structures in the Taibei depression made the mechanism of accumulation complicated. The author provided proof of episodic accumulation of hydrocarbon in this area: The organic component in the boiling inclusion is the trail of petroleum migration, showing the causality between the boiling of thermal fluid and the chimney structures, meanwhile showing the paroxysmal accumulation is an important petroleum accumulation model. Based on the evolutionary characteristics of various types of chimney structures, this paper discussed their relationships with the migration-accumulation of petroleum respectively. At the same time, the author summarized the accumulating-dynamical models associated with chimney structures. The author analyzed such accumulation mechanisms as the facies state, direction, power of petroleum migration, the conditions of trap, the accumulation, leakage and reservation of petroleum, and the distribution rule of petroleum. The author also provides explanation for such practical problems the existence of a lot of mantle-derived CO_2, and its heterogeneous distribution on plane. By study on and recognition for chimney structure, the existence and distribution of much mantle-derived CO_2 found in this area are explained. Caused by tectonic thermal activities, the deep magma with much CO_2-bearing thermal fluid migrate upward along deep fault and chimney structures, which makes two wells within relatively short distance different gas composition, such as in well LF-1 and well LS36-1-1. Meanwhile, the author predicted the distribution of petroleum accumulation belt in middle-shallow layer for this area, pointed out the three favorable exploration areas in future, and provided the scientific and deciding references for future study on the commingling-genetic accumulation of petroleum in middle-deep layer and the new energy-gas hydrate.

河流成因储层沉积微相与剩余油分布及形成机理研究

Based on the study of fluvial sandstone reservoir in upper of Guantao group in Gudao and Gudong oilfields, this paper first introduces A.D.Miall's(1996a) architectural-element analysis method that was summarized from ground outcrop scale into the reservoir formation research of the study area, more subtly divides sedimentary microfacies and establishes sedimentary model of research area.on this base, this paper summarizes the laws of residual oil distribution of fluvial formation and the control effect of sedimentary microfacies to residual oil distribution, and reveals residual oil formation mechanism. These results have been applied to residual oil production, and the economic effect is good. This paper will be useful for residual oil research and production and enhancement of oil recovery in similar reservoir. The major conclusions of this paper are as follows. 1. Using the architectural-element analysis method to the core data, a interfacial division scheme of the first to the dixth scale is established for the studied fluvial formation. 2.Seven architectural-elements are divided in upper of Guantao group of study area. The sandstone group 5～1+2 of Neogene upper Gutao group belongs to high sinuous fine grain meandering river, and the sandstone group 6 is sandy braided river. 3. Inter layer, the residual oil saturation of "non-main layer" is higher than "main layer", but the residual recoverable reserve of former is larger. Therefore, "main layer" is the main body of residual oil distribution. The upper and middle part of inner layer has lower permeability and strong seeping resistance. Addition to gravity effect in process of driving, its driving efficiency is low; residual oil saturation is high. Because of controlling of inside non-permeable interlayer or sedimentary construction, the residual oil saturation of non-driving or lower driving efficiency position also is high. On plane, the position of high residual oil saturation mostly is at element LV, CS, CH (FF), FF etc, Which has lower porosity and permeability, as well as lens sand-body and sand-body edge that is not controlled by well-net, non-perfect area of injection and production, lower press difference resort area of inter-well diffiuent-line and shelter from fault, local high position of small structure. 4.Microscopic residual oil mainly includes the non-moved oil in the structure of fine pore network, oil in fine pore and path, oil segment in pore and path vertical to flow direction, oil spot or oil film in big pore, residual oil in non-connective pore. 5.The most essential and internal controlling factor of fluvial formation residual oil distribution is sedimentary microfacies. Status of injection and production is the exterior controlling factor of residual oil distribution. 6. The controlling effect of formation sedimentary microfacies to residual oil distribution indicates inter-layer vertical sedimentary facies change in scale of injection and production layer-series, planar sedimentary face change and inner-layer vertical sedimentary rhythm and interbed in single layer to residual oil distribution. 7. It is difficult to clear up the inter-layer difference in scale of injection and production layer-series. The using status of minor layer is not good and its residual oil saturation is high relatively. It is obvious that inter-layer vertical sedimentary facies changes control inter-layer residual oil distribution at the same or similar conditions of injection and production. For fluvial formation, this vertical sedimentary facies change mainly is positive gyration. Namely, from down to top, channel sediment (element CHL, LA) changes into over-bank sediment (element LV, CR, CS). 8. In water-injection developing process of transverse connecting fluvial sandstone oil formation, injection water always comes into channel nearby, and breaks through along channel and orientation of high pressure gradient, does not expand into side of channel until pressure gradient of channel orientation changes into low. It brings about that water-driving status of over-bank sedimentary element formation (LV, CR, CS) is not good, residual oil saturation is high. In non-connective abandoned channel element (CH) formation with channel, because this reverse is difficult to control by injection and production well-series, its using status is not good, even terribly not good, residual oil is enrichment. 9. The rhythm and sedimentary structure, sedimentary facies change in single sand body brings about vertical changes of formation character, growth character of inner layer interbed. These are important factor of controlling and affecting vertical water spread volume and inner layer residual oil forming and distribution in single sand body. Positive rhythm, is the principal part of fluvial sandstone inner layer sedimentary rhythm. Namely, from down to upside, rock grain granularity changes from coarse to fine, seeping ability changes from strong to feebleness. It brings about that water-driving status of inner layer upside is not good, residual oil saturation is high. Inner layer interbed has different degree affecting and controlling effect to seeping of oil and water. Its affecting degree lies on interbed thickness, extending scale, position, and jeted segment of production or injection well. The effect of interbed at upside of oil formation to oil and water seeping is less; the effect of interbed at middle of oil formation to oil and water seeping is more. 10. Indoor experiment and research indicate that wettability, permeability step, vertical permeability, position of Kmax and ratio of oil viscousity and water viscousity all have great effect on the water-driving recovery ratio. 11. Microscopic residual oil distribution is affected and controlled by formation pore network structure, pressure field distribution, and oil characteristic. 12.The residual oil forming mechanism: the over-bank sedimentary element and upper part of a positive rhythm sandstone have fine pore and throat network, permeability is low, displacement pressure of pore and throat is high. The water-driving power usually falls short of displacement pressure that brings about injection water does not spread into these pore and throat network, thereby immovable oil area, namely residual oil, is formed. At underside of channel sedimentary element and positive rhythm sandstone, porosity and permeability is relatively high, connecting degree of pore and throat is high, displacement pressure of pore and throat is low. Thereby injection water is easy to enter into pore and throat, driving oil in them. Because the pore space is irregular, the surface of pore wall is coarse and non-flat. That the oil locate on concave hole of pore wall and the dead angle of pore, and the oil attaches on surface of pore wall by surface tension, are difficult to be peeled off, becoming water-driving residual oil (remaining oil). On the other hand, Because flowing section lessens, flowing resistance increase, action of capillary fore, or seeping speed decreases at process of transfer at pass narrow throat path in the course carried by driving water. The "oil drop", "oil bead", or "oil segment" peeled off by driving water is difficult to carry and to drive out by water at less pressure difference. Thereby they are enclosed in pore to form discontinuous residual oil. 13.This results described above have been applied in nine develop blocks of Gudao and Gudong oilfield. Its applying effect is marked through local injection production adjustment, deploying replacement well, repair hole, replacement envelop, block off water and profile control etc. Relative method and technology can be applied to other oil production area of Shengli oilfield, and obtain better economic and societal effect.

沾化凹陷泥质岩油气藏成藏特征研究

Mudstone reservoir is a subtle reservoir with extremely inhomogeneous, whose formation is greatly related to the existence of fracture. For this kind of reservoir, mudstone is oil source rock, cover rock and reservoir strata, reservoir type is various, attitude of oil layer changes greatly, and the distribution of oil and gas is different from igneous or clastic rock reservoir as well as from carbonate reservoir of self-producing and self-containing of oil and gas. No mature experience has been obtained in the description, exploration and development of the reservoir by far. Taking Zhanhua depression as an example, we studied in this thesis the tectonic evolution, deposit characteristics, diagenesis, hydrocarbon formation, abnormal formation pressure, forming of fissure in mudstone reservoir, etc. on the basis of core analysis, physical simulation, numerical simulation, integrated study of well logging and geophysical data, and systematically analyzed the developing and distributing of mudstone fissure reservoir and set up a geological model for the formation of mudstone fissure reservoir, and predicted possible fractural zone in studied area. Mudstone reservoir mainly distributed on the thrown side of sedimentary fault along the sloping area of the petroleum generatiion depression in Zhanhua depression. Growing fault controlled subsidence and sedimentation. Both the rate of subsidence and thickness of mudstone are great on the thrown side of growing fault, which result in the formation of surpressure in the area. The unlocking of fault which leads to the pressure discharges and the upward conduct of below stratum, also makes for the surpressure in mudstone. In Zhanhua depression, mudstone reservior mainly developed in sub-compacted stratum in the third segment of Shahejie formation, which is the best oil source rock because of its wide spread in distribution, great in thickness, and rich in organic matter, and rock types of which are oil source mudstone and shale of deep water or semi-deep water sediment in lacustrine facies. It revealed from core analysis that the stratum is rich in limestone, and consists of lamina of dark mudstone and that of light grey limestone alternately, such rock assemblage is in favor of high pressure and fracture in the process of hydrocarbon generation. Fracture of mudstone in the third segment of Shahejie formation was divided into structure fracture, hydrocarbon generation fracture and compound fracture and six secondary types of fracture for the fist time according to the cause of their formation in the thesis. Structural fracture is formed by tectonic movement such as fold or fault, which develops mainly near the faults, especially in the protrude area and the edge of faults, such fracture has obvious directivity, and tend to have more width and extension in length and obvious direction, and was developed periodically, discontinuously in time and successively as the result of multi-tectonic movement in studied area. Hydrocarbon generation fracture was formed in the process of hydrocarbon generation, the fracture is numerous in number and extensively in distribution, but the scale of it is always small and belongs to microfracture. The compound fracture is the result of both tectonic movement and hydrocarbon forming process. The combination of above fractures in time and space forms the three dimension reservoir space network of mudstone, which satellites with abnormal pressure zone in plane distribution and relates to sedimentary faces, rock combination, organic content, structural evolution, and high pressure, etc.. In Zhanhua depression, the mudstone of third segment in shahejie formation corresponds with a set of seismic reflection with better continuous. When mudstone containing oil and gas of abnormal high pressure, the seismic waveform would change as a result of absorb of oil and gas to the high-frequency composition of seismic reflection, and decrease of seismic reflection frequency resulted from the breakage of mudstone structure. The author solved the problem of mudstone reservoir predicting to some degree through the use of coherent data analysis in Zhanhua depression. Numerical modeling of basin has been used to simulate the ancient liquid pressure field in Zhanhua depression, to quantitative analysis the main controlling factor (such as uncompaction, tectonic movement, hydrocarbon generation) to surpressure in mudstone. Combined with factual geologic information and references, we analyzed the characteristic of basin evolution and factors influence the pressure field, and employed numerical modeling of liquid pressure evolution in 1-D and 2-D section, modeled and analyzed the forming and evolution of pressure in plane for main position in different periods, and made a conclusion that the main factors for surpressure in studied area are tectonic movement, uncompaction and hydrocarbon generation process. In Zhanhua depression, the valid fracture zone in mudstone was mainly formed in the last stage of Dongying movement, the mudstone in the third segment of Shahejie formation turn into fastigium for oil generation and migration in Guantao stage, and oil and gas were preserved since the end of the stage. Tectonic movement was weak after oil and gas to be preserved, and such made for the preserve of oil and gas. The forming of fractured mudstone reservoir can be divided into four different stages, i.e. deposition of muddy oil source rock, draining off water by compacting to producing hydrocarbon, forming of valid fracture and collecting of oil, forming of fracture reservoir. Combined with other regional geologic information, we predicted four prior mudstone fracture reservoirs, which measured 18km2 in area and 1200 X 104t in geological reserves.

大别山硬玉石英岩带中的水

The Dabie Mountains is a collisional orogenic belt between the North China and Yantze Continental plates. It is the eastern elongation of the Tongbai and Qingling orogen, and is truncated at its east end by the Tan-Lu fault. Jadeite-quartzite belt occurs in the eastern margin of UHPMB from the Dabie Mountains. Geochemical features indicate that the protoliths of the jadeite-quartzite and associated eclogite to be supracrustal rocks. The occurrence of micro-inclusions of coesite in jadeite and garnet confirmed that the continental crust can be subducted to great depth (8 0-100km) and then exhumed rapidly with its UHP mineral signature fairly preserved. Therefore, study of UHP jadeite-quartzite provides important information on subduction of continental crustal rocks and their exhumation histories, as well as the dynamics of plate tectonic processes at convergent margins. The purpose of this paper is to investigate the presence of hydrous component in the jadeite-quartzite belt, significant natural variations in the hydrous component content of UHP minerals and to discuss the role of water in petrology, geochemistry and micro-tectonic. On the basis of our previous studies, some new geological evidences have been found in the jadeite-quartzite belt by researches on petrography, mineralogy, micro-tectonic, hydrous component content of UHP minerals and combined with the study on rheology of materials using microprob, ER, TEM. By research and analysis of these phenomenona, the results obtained are as follows: 1. The existence of fluid during ultra-high pressure metamorphic process. Jadeites, omphacite, garnet, rutile, coesite and quartz from the jadeite-quartzite belt have been investigated by Fourier transform infrared spectrometer and TEM. Results show that all of these minerals contain trace amount of water which occur as hydroxyl and free-water in these minerals. The two-type hydrous components in UHP minerals are indicated stable in the mantle-depth. The results demonstrated that these ultra-high pressure metamorphic minerals, which were derived from continental crust protoliths, they could bring water into the mantle depth during the ultra-high pressure metamorphism. The clusters of water molecules within garnet are very important evidence of the existence of fluid during ultra-high pressure metamorphic process. It indicated that the metamorphic system was not "dry"during the ultra-high pressure stage. 2.The distribution of hydrous component in UHP minerals of jadeite-quartzite. The systematic distribution of hydrous components in UHP minerals are a strong indication that water in these minerals, are controlled by some factors and that the observed variations are not of a random nature. The distribution and concentration of hydrous component is not only correlated with composition of minerals, but also a function of geological environment. Therefore, the hydrous component in the minerals can not only take important part in the UHP metamorphic fluid during subduction of continental crustal rocks, but also their hydroxyl transported water molecules with decreasing pressure during their exhumation. And these water molecules can not only promote the deformation of jadeite through hydrolytic weakening, but also may be the part of the retrograde metamorphic fluid. 3.The role of water in the deformed UHP minerals. The jadeite, omphacite, garnet are strong elongated deformation in the jadeite-quartzite from the Dabie Mountains. They are (1) they are developed strong plastic deformation; (2) developed dislocation loop, dislocation wall; (3) the existence of clusters of water molecular in the garnet; and (4) the evolution of micero-tectonic from clusters of water molecular-dislocation loop in omphacite. That indicated that the water weakening controlled the mechanism of deformed minerals. Because the data presented here are not only the existence of clusters of water molecular in the garnet, but also developed strong elongation, high density of dislocation and high aspect ratios, adding microprobe data demonstrate the studied garnet crystals no compositional zoning. Therefore, this indicates that the diffusion process of the grain boundary mobility did not take place in these garnets. On the basis of above features, we consider that it can only be explained by plastic deformation of the garnets. The clusters of water molecules present in garnet was directly associated with mechanical weakening and inducing in plastic deformation of garnet by glissile dislocations. Investigate of LPO, strain analysis, TEM indicated that these clinopyroxenes developed strong elongation, high aspect ratios, and developed dislocation loop, dislocation wall and free dislocations. These indicated that the deformation mechanism of the clinopyroxenes plastically from the Dabie Mountains is dominant dislocation creep under the condition of the UHP metamorphic conditions. There are some bubbles with dislocation loops attached to them in the omphacite crystal. The bubbles attached to the dislocation loops sometimes form a string of bubble beads and some loops are often connected to one another via a common bubble. The water present in omphacite was directly associated with hydrolitic weakening and inducing in plastic deformation of omphacite by dislocations. The role of water in brittle deformation. Using microscopy, deformation has been identified as plastic deformation and brittle deformation in UHP minerals from the Dabie Mountains. The study of micro-tectonic on these minerals shows that the brittle deformation within UHP minerals was related to local stresses. The brittle deformation is interpreted as being caused by an interaction of high fluid pressure, volume changes. The hydroxyl within UHP minerals transported water molecules with decreasing pressure due to their exhumation. However, under eclogite facies conditions, the litho-static pressure is extreme, but a high fluid pressure will reduce the effective stress and make brittle deformation possible. The role of water in prograde metamorphism. Geochemical research on jadeite-quartzite and associated eclogite show that the protoliths of these rocks are supracrustal rocks. With increasing of temperature and pressure, the chlorite, biotite, muscovite was dehydrous reaction and released hydrous component during the subduction of continental lithosphere. The supracrustal rocks were transformed UHP rocks and formed UHP facies assemblage promotely by water introduction, and was retained in UHP minerals as hydrous component. The water within UHP minerals may be one of the retrograde metamorphic fluids. Petrological research on UHP rocks of jadeite-quartzite belt shows that there was existence of local fluids during early retrograde metamorphism. That are: (1) coronal textures and symplectite around relict UHP minerls crystals formed from UHP minerls by hydration reactions; (2) coronal textures of albite around ruitle; and (3) micro-fractures in jadeite or garnet were filled symplectite of Amp + PI + Mt. That indicated that the reactions of early retrograde metamorphism dependent on fluid introduction. These fluids not only promoted retrograde reaction of UHP minerals, but also were facilitate to diffuse intergranular and promote growth in minerals. Therefore, the hydrous component in the UHP minerals can not only take important part in the UHP metamorphic fluid during subduction of continental crustal rocks, but also their hydroxyl transport water molecules with decreasing pressure and may take part in the retrograde metamorphic fluid during their exhumation. 7. The role of water in geochemistry of UHP jadeite-quartzite. Geochemical research show that there are major, trace and rare earth element geochemical variations in the jadeite-quartzite from the Changpu district of Dabie Mountains, during retrograde metamorphic processes from the jadeite-quartzite--gneiss. The elements such as SiO_2、FeO、Ba、Zr、Ga、La、Ce、PTN Nd% Sm and Eu increase gradually from the jadeite-quartzite to retrograded jadeite-quartzite and to gneiss, whilst TiO_2. Na_2CK Fe2O_3、Rb、Y、Nb、Gd、Tb、Dy、Ho、Er、Tm、Yb decrease gradually. And its fO_2 keep nearly unchanged during early retrograde metamorphism, but decreased obviously during later retrograde metamorphism. These indicate that such changes are not only controlled by element transformation between mineralogical phases, but also closely relative to fluid-rock interaction in the decompression retrograde metamorphic processes.

孤北洼陷沙三-沙四段隐蔽油藏形成机制及其预测

Based on the study of sequence stratigraphy, modern sedimentary, basin analysis, and petroleum system in Gubei depression, this paper builds high resolution sequence stratigraphic structure, sedimentary system, sandbody distribution, the effect of tectonic in sequence and sedimentary system evolution and model of tectonic-lithofacies. The pool formation mechanism of subtle trap is developed. There are some conclusions and views as follows. 1.With the synthetic sequence analysis of drilling, seismic, and well log, the highly resolution sequence structure is build in Gubei depression. They are divided two secondary sequences and seven three-order sequences in Shahejie formation. They are include 4 kinds of system traces and 7 kinds of sedimentary systems which are alluvial fan, under water fan, alluvial fan and fan-delta, fan-delta, lacustrine-fan, fluvial-delta-turbidite, lakeshore beach and bar, and deep lake system. Sandbody distribution is show base on third order sequence. 2.Based on a lot of experiment and well log, it is point out that there are many types of pore in reservoir with the styles of corrosion pore, weak cementing, matrix cementing, impure filling, and 7 kinds of diagenetic facies. These reservoirs are evaluated by lateral and profile characteristics of diagenetic facies and reservoir properties. 3.The effect of simultaneous faulting on sediment process is analyzed from abrupt slope, gentle slope, and hollow zone. The 4 kinds of tectonic lithofacies models are developed in several periods in Gubei depression; the regional distribution of subtle trap is predicted by hydro accumulation characteristics of different tectonic lithofacies. 4.There are 4 types of compacting process, which are normal compaction, abnormal high pressure, abnormal low pressure and complex abnormal pressure. The domain type is normal compaction that locates any area of depression, but normal high pressure is located only deep hollow zone (depth more than 3000m), abnormal low pressures are located gentle slope and faulted abrupt slope (depth between 1200~2500m). 5.Two types dynamic systems of pool formation (enclosed and partly enclosed system) are recognized. They are composed by which source rocks are from Es3 and Es4, cap rocks are deep lacustrine shale of Esl and Es3, and sandstone reservoirs are 7 kinds of sedimentary system in Es3 and Es4. According to theory of petroleum system, two petroleum systems are divided in Es3 and Es4 of Gubei depression, which are high or normal pressure self-source system and normal or low pressure external-source system. 6.There are 3 kinds of combination model of pool formation, the first is litholgical pool of inner depression (high or normal pressure self-source type), the second is fault block or fault nose pool in marginal of depression (normal type), the third is fault block-lithological pool of central low lifted block (high or normal pressure type). The lithological pool is located central of depression, other pool are located gentle or abrupt slope that are controlled by lithological, faulting, unconfirmed. 7.This paper raise a new technique and process of exploration subtle trap which include geological modeling, coring description and logging recognition, and well log constrained inversion. These are composed to method and theory of predicting subtle trap. Application these methods and techniques, 6 hydro objects are predicted in three zone of depression.

东大别山晚中生代主剪切带及伸展构造研究

Dabie shan lies between Northchina crust and Yangzi crust, which is the result of the collisional orogenen in Triassic period. The biggest area of UHP metamorphic zone have been found in Dabie Shan, which have been verified formed during the course of collision and extrusion after orogenic activity. The Dabie shan is divisioned into four parts, which are North Huaiyang metamorphic zone, North Dabie complex zone, South Dabie ultra-high pressure metamorphic zone and Susong metamorphic zone. Extension structure of late Mesozoic is the key to explain the intrusion and outcrop of UHP metamorphic rocks in Dabie Shan. During the course of structure evolution of the Dabie shan in late Mesozoic period, Luotian dome was formed with the old gneiss lifting from the core of the Dabie shan. There are four enormous ductile zone circled Luotian dorm. Xiaotian-mozitan shear zone is the limit of North Huaiyang metamorphic zone and North Dabie complex zone; Shuihou-wuhe shear zone is the limit of North Dabie complex zone and South Dabie ultra-high pressure metamorphic zone; Taihu-mamiao shears zone is the limit of South Dabie ultra-high pressure metamorphic zone and Susong metamorphic zone and Susong-Qingshuihe shear zone is the south limit of Susong metamorphic zone; the old stress at Dabie shan in late Mesozoic was about 90MPa through the experiment of transmission electricity microscope. The main four ductile shear zone of Dabie shan all have the characteristic of detachment, Xiaotian-mozitan shear zone detached to NNE, the detachment direction of Shuihou-wuhe shear zone and Taihu-mamiao shears zone is SSE, and Susong-Qingshuihe shear zone is SW. The finite strain measurement show that Xiaotian-mozitan shear zone have experienced detachment which was more than 50km, and the detachment of Susong-Qingshuihe shear zone was more than 12km in late Mesozoic; the Flin parameter of Shuihou-wuhe shear zone is much smaller than 1(0.01-0.1), which show that this shear zone was squeezed when it was formed and the initiative function of Luotian granite intrusion during the course of detachment. The Flin parameter of Taihu-mamiao shears zone is above 1(1.1) and Susong-Qingshuihe shear zone is much more than 1(7.6), which show that they are formed in the state of extension at the beginning. These all Flin parameter imply a transition from pure shear to simple shear of the south three shear zone circling Luotian dome from north to south. The rock group analysis show that the rocks inside shear zone encountered middle or high temperature metamorphic activity. The single mineral ~(40)Ar/~(39)Ar age of the main shear zone at Dabie shan show that the three shear zone north to Luotian dome were formed about 190Ma.Taihu-mamiao shear zone was the earliest, Susong shear zone was later than former, and Shuihou-wuhe sheanaone was the latest. They were all the chanel of returning of UHP metamorphic rocks, so they all representative the returning age of UHP metamorphic rocks. The final outcrop of these UHP metamorphic rocks was due to the detachment aroused by the enormous magma intrusion. The biotite age of deformed rocks in Susong-Qingshuihe shear zone is in average 126Ma, and the age of Xiaotian-mozitan is about 125Ma, which is in the same time or a little later than magma intrusion of Luotian dome, and imply that granite intrusion of late Mesozoic in Dabie orogenen is the reason of the detachment.

大港千米桥地区综合地质地球物理研究

Qianmiqiao buried hill, which is a high-yield burial hill pool, was discovered at Dagang oilfield in 1998. To employ the integrated geological and geophysical research at Qianmiqiao area, it is very valuable and meaningful for the petroleum exploration of Bohai Bay Basin and even the whole country. Based on the previous results, this paper is carried out from the research on Huanghua depression, following the law, i.e. the deep part constrains the shallow, the regional constrains the local, takes the geophysical research in Qianmiqiao oilfield, discusses the formation history of burial hills, burial history, thermal history, the generated and expelling history of hydrocarbon, and migration characteristics, probes into the formation of burial hill pool. This paper uses the gravity and magnetic methods which are based on potential field, with natural sources, configures the inner structure of the earth according to the difference in the density and magnetism of the rock. The geophysical characteristics of Dagang oil field is that it is an area with positive Buge gravity anomal. The upheaval of Moho boundary is in mirror symmetry with the depression of the basin's basement. The positive and negative anomaly distributein axis symmetry, and the orientation is NNE. The thickness of the crust gradually reduces from west to east, from land to sea. The depth gradient strip of Curie surface is similar to Moho boundary, whereas their local buried depth is different. Local fractures imply that the orientation of base rock fractures is NNE-NE, and the base rock is intersected by the fractures of the same/ later term, whose orientation is NW, so the base rock likes rhombic mosaic. The results of tomography show that there exists significant asymmetry in vertical and horizontal direction in the velocity configuration of Huanghua depression. From Dezhou to Tianjin, there exits high-speed block, which extends from south to north. The bottom of this high-speed block is in good agreement with the depth of Moho boundary. Hence we can conclude that the high-speed block is actually the crystal basement. According to seismic data, well data and outcrop data, Huanghua depression can be divided into four structure layers, i.e. Pi,2-T, Ji,2-K, E, N-Q. Qianmiqiao burial hills undergo many tectonic movement, where reverse faults in developed in inner burial hill from Indosinian stage to Yanshanian stage, the normal faults extended in Himalayan stage. Under the influence of tectonic movements, the burial hills show three layers, i.e. the reverse rushing faults in buried hills, paleo-residual hill, and extended horst block. The evolution of burial hills can be divided into four stages: steady raising period from Calenonian to early Hercynian, rushing brake drape period from Indosinian to middle Yanshanian, block tilting period in early Tertiary, and heating depression period from late Tertiary to Quaternary. The basin modeling softwares BasinMod 1-D and Basin 2-D, which are made by PRA corporation, are used in this paper, according to the requirement, corresponding geological model is designed. And we model the burial history, thermal history, hydrocarbon generation and hydrocarbon expelling history of Qianmiqiao area. The results show that present bury depth is the deepest in the geological history, the sedimentary rate of Tertiary is highest and its rising rate of temperature rate is higher. During sedimentary history, there is no large erosion, and in the Tertiary, the deeper sediment was deposited in large space, therefore it is in favor of the conservation and transformation of oil and gas. The thermal research shows that the heat primarily comes from basement of the basin, present geotherm is the highest temperature in the geological history. Major source rock is the strata of ES3, whose organic is abundant, good-typed, maturative and of high-expulsive efficiency. The organic evolution of source rock of O has come to the overmature stage, the evolving time is long and the source rock can be easily destroyed. Therefore it is more difficult for the O formation source rock to form the huge accumulation of oil and gas than Es3 formation. In the research of oil assembling, we first calculated the characteristics of the fluid pressure of single well, then analyzed the distribution of the surplus fluid pressure of each formation and profile, and probe the first hydrocarbon migration situation and the distribution of pressure system of buried hill pool. In every formation, the pressure system of each burial hill has its own characteristics, e.g. high pressure or low pressure. In the research of secondary migration, the fluid potential is calculated while the relative low potential area is figured out. In Qianmiqiao area, the west margin faults have the low potential, and hence is the favorable reconnoiter belt.

大别山太湖地区榴辉岩变质P-T条件及构造意义

As far as the architecture of the south Dabie metamorphic terrain is concerned, there have been lots of different opinions for a long time. Wang et al. (1990, 1992) thought of it was a continuous terrain. Okay (1993) held that it consistes of two different tectonic terrains: the 'hot' and 'cold' eclogite belt. Liu and Wang (1998) held that it is composed of different metamorphic blocks through 'melange' in depth. For this reason, we have choiced Hualiangting reservoir of Taihu county as the study area treat eclogite as the investigated objection in this thesis, and employ the detailed 1 :10000 geological mapping, methods of Petrography and electonic probe anaylsis to probe into the architecture of the south Dabie metamorphic terrains. In the light of the eclogite occurrenc in the field, the analysis of Petrography, the research on metamoiphic P-T path and condition of the peak metamorphic P-T condition, the eclogite in the Taihu area of Dabieshan have been classified into three types eclogite from the south to the north: The zhujiachong type eclogite; The Daba type eclogite; (3) The Jinheqiao type eclogite, their mineral composition, structure, and mineral component vary continuously. These eclogites have the same rnetamoiphic stages, P-T evolution pattern, and their peak P-T condition varies continuously. The zhujiachong type eclogite is formed in the high pressure metamoiphic environment. The Jinheqiao type eclogite is formed in the typical ultra-high pressure environment. The Daba type eclogite is formed in the transformed metamorphic environment between high pressure and ultra-high pressure metamorphism. All these evidences show that the south Dabie metamorphic terrain is a continuous metamorphic block and no large fault ever existed.

基于结构分析地震资料去噪方法研究

With the development of oil and gas exploration, the exploration of the continental oil and gas turns into the exploration of the subtle oil and gas reservoirs from the structural oil and gas reservoirs in China. The reserves of the found subtle oil and gas reservoirs account for more than 60 percent of the in the discovered oil and gas reserves. Exploration of the subtle oil and gas reservoirs is becoming more and more important and can be taken as the main orientation for the increase of the oil and gas reserves. The characteristics of the continental sedimentary facies determine the complexities of the lithological exploration. Most of the continental rift basins in East China have entered exploration stages of medium and high maturity. Although the quality of the seismic data is relatively good, this areas have the characteristics of the thin sand thickness, small faults, small range of the stratum. It requests that the seismic data have high resolution. It is a important task how to improve the signal/noise ratio of the high frequency of seismic data. In West China, there are the complex landforms, the deep embedding the targets of the prospecting, the complex geological constructs, many ruptures, small range of the traps, the low rock properties, many high pressure stratums and difficulties of boring well. Those represent low signal/noise ratio and complex kinds of noise in the seismic records. This needs to develop the method and technique of the noise attenuation in the data acquisition and processing. So that, oil and gas explorations need the high resolution technique of the geophysics in order to solve the implementation of the oil resources strategy for keep oil production and reserves stable in Ease China and developing the crude production and reserves in West China. High signal/noise ratio of seismic data is the basis. It is impossible to realize for the high resolution and high fidelity without the high signal/noise ratio. We play emphasis on many researches based on the structure analysis for improving signal/noise ratio of the complex areas. Several methods are put forward for noise attenuation to truly reflect the geological features. Those can reflect the geological structures, keep the edges of geological construction and improve the identifications of the oil and gas traps. The ideas of emphasize the foundation, give prominence to innovate, and pay attention to application runs through the paper. The dip-scanning method as the center of the scanned point inevitably blurs the edges of geological features, such as fault and fractures. We develop the new dip scanning method in the shap of end with two sides scanning to solve this problem. We bring forward the methods of signal estimation with the coherence, seismic wave characteristc with coherence, the most homogeneous dip-sanning for the noise attenuation using the new dip-scanning method. They can keep the geological characters, suppress the random noise and improve the s/n ratio and resolution. The rutine dip-scanning is in the time-space domain. Anew method of dip-scanning in the frequency-wavenumber domain for the noise attenuation is put forward. It use the quality of distinguishing between different dip events of the reflection in f-k domain. It can reduce the noise and gain the dip information. We describe a methodology for studying and developing filtering methods based on differential equations. It transforms the filtering equations in the frequency domain or the f-k domain into time or time-space domains, and uses a finite-difference algorithm to solve these equations. This method does not require that seismic data be stationary, so their parameters can vary at every temporal and spatial point. That enhances the adaptability of the filter. It is computationally efficient. We put forward a method of matching pursuits for the noise suppression. This method decomposes any signal into a linear expansion of waveforms that are selected from a redundant dictionary of functions. These waveforms are chosen in order to best match the signal structures. It can extract the effective signal from the noisy signal and reduce the noise. We introduce the beamforming filtering method for the noise elimination. Real seismic data processing shows that it is effective in attenuating multiples and internal multiples. The s/n ratio and resolution are improved. The effective signals have the high fidelity. Through calculating in the theoretic model and applying it to the real seismic data processing, it is proved that the methods in this paper can effectively suppress the random noise, eliminate the cohence noise, and improve the resolution of the seismic data. Their practicability is very better. And the effect is very obvious.

亚洲地形和海陆分布变化对东亚环境格局形成演化的作用：数值模拟与地质记录对比

Earlier studies on the distribution of geological environmental indicators in China revealed drastic changes from a zonal climate pattern (planetary-wave-dominant pattern) in the Paleogene to a monsoon-dominant one in the Neogene, which suggested an inception of the initial East-Asian summer monsoon. However, there are different views about the time and causes of the changes.Here, we attempt to compile a series of paleoenvironmental maps based on newly collected climate indicators from the literatures and chronologically constrained evidence of geological maps in order to re-examine the temporal and spatial evolution of climate belts in China during the Cenozoic with special emphasis on the changes of the arid belt. These indicators include mammalian fauna, coal, carbonate concretions, jarosite, salt, gypsum deposits and pollen assemblages etc, with chronological controls that we believe reliable. Pollen assemblages and mammalian fauna have been classified into three categories (arid, semi-arid/sub-humid, humid) to reflect the intensity of aridity/humidity. Salt, jarosite and gypsum deposits are classified as the arid indicators. Carbonate concretions and coal are classified into the semi-arid/sub-humid and humid one respectively. Paleoenvironmental maps at 8 time slices have been reconstructed. They are the Paleocene, Eocene, Oligocene, Miocene, Early Miocene, Middle Miocene, Late Miocene and Pliocene.And furthermore, we attempt to use IAP^AGCM to simulate the evolution of climate belts in emphasizing on the changes of the rain band, and compare the results with the paleoenvironmental maps in order to examine the causes of the drastic paleoenvironmental changes near the Oligocene/Miocene boundary. 36 sensitive numerical experiments are carried out using the IAP__AGCM to analyze the impacts of the uplift of the Himalayan-Tibetan complex, shrinkage of the Paratethys Sea, expansion of the South China Sea and the development of the polar ice sheets on rain band in China.The main conclusions are as follows:The obtained results essentially confirm the earlier conclusions about a zonal climate pattern in the Paleogene and a different pattern in the Neogene, and illustrate that a monsoon-dominant environmental pattern with inland aridity formed by the Early Miocene, which is temporally consist with the onset of eolian deposits in China.Cenozoic cooling and the formation of polar ice sheets are unlikely the main causes to the changes of environmental patterns mentioned above in China. But northern hemispheric cooling and the ice-sheets can intensify the Siberian High Pressure, and strengthen the winter monsoon circulations and enhance the aridity in the west part of China. These results support the earlier studies.Shrinkage of the Paratethys Sea and uplift of the Himalayan-Tibetan complex played important roles in strengthening the East Asian monsoon and induceing the above changes of environmental pattern, which is consistent with the earlier studies. Furthermore, "the monsoon-dominant pattern" appears when the Himalayan-Tibetan complex reaches to about 1000-2000 meters high and the Paratethys Sea retreats to the Turan Plate.4) Expansion of the South China Sea is another significant factor that drives the evolution of environmental patterns. We believe that the above three factors co-act and drive the change of the environmental patterns from a planetary-wave-dominant one to a monsoon-dominant one. However, the impacts of each factor vary by regions. The uplift mainly increases the humidity in Southwestern China and the aridity in northwestern country. The shrinkage mainly increases the humidity in Northern China and also enhances the aridity in the northwestern country. The expansion greatly increases the humidity in the south part of China.

克拉2异常高压气藏地质特征及开发技术研究

Kela-2 gas field in Tarim Basin is the main supply source for West-to-East Pipeline project, also the largest abnormally-pressured gas field discovered in China currently. The geological characterization, fine geological modeling and field development plan are all the world-class difficult problems. This work includes an integrated geological and gas reservoir engineering study using advanced technology and approaches, the scientific development plan of Kela-2 gas field as well as the optimizations of the drilling, production and surface schemes. Then, it's expected that the Kela-2 gas field can be developed high-efficiently.Kuche depression is one part of the thrust belt of the South Tianshan Mountains, Kela-2 field is located at the Kelasu structural zone in the north of Kuche depression. The field territory is heavily rugged with deeply cut gullies, complex geological underground structure, variable rock types, thrust structure development. Therefore, considerable efforts have been made to develop an integrated technique to acquire, process and interpret the seismic data in complicated mountain region. Consequently a set of seismic-related techniques in the complicated mountain region has been developed and successfully utilized to interpret the structure of Kela-2 gas field.The main reservoir depositional system of Kela 2 gas field is a platform - fan delta - braided river system. The reservoir rocks are medium-fine and extremely fine grained sandstones with high structure maturity and low composition maturity. The pore system structure is featured by medium-small pore, medium-fine throat and medium-low assortment. The reservoir of Kela-2 gas field is characteristic of medium porosity and medium permeability. The pay zone is very thick and its lateral distribution is stable with a good connection of sand body. The overpressure is caused mainly by the strongly tectonic squash activities, and other factors including the later rapid raise and compartment of the high-pressure fluid, the injection of high-pressure fluid into the reservoir.Based on the deliverability tests available, the average binomial deliverability equation is provided applicable for the overall field. The experimental results of rock stress-sensitive tests are employed to analyze the change trend of petrophysical properties against net confining stress, and establish the stress-based average deliverability equation. The results demonstrate the effect of rock deformation on the deliverability is limited to less than 5% in the early period of Kela-2 gas field, indicating the insignificant effect on deliverability of rock deformation.In terms of the well pattern comparisons and development planning optimizations, it is recommended that the producers should be located almost linearly along the structural axis. A total of 9 producers have a stable gas supply volume of 10.76 BCMPY for 17 years. For Kela-2 gas field the total construction investment is estimated at ￥7,697,690,000 RMB with the internal earning rate of 25.02% after taxation, the net present value of ￥7,420,160,000 RMB and the payback period of 5.66 years. The high profits of this field development project are much satisfactory.

高温高压条件下泥质岩变质脱水作用的实验研究

泥质岩是地球上广泛分布的一种表壳沉积岩石，与上地壳平均化学组成接近，是俯冲带沉积物的典型代表。本文以赣北双桥山群泥质板岩为主要研究对象，对泥质岩（KFMASH体系）进行了热力学计算、高压差热（HP－DTA）和榴辉岩相温压条件下变质脱水作用的实验研究。研究结果表明，俯冲沉积物在冷、热俯冲带其变质脱水作用的深度范围分别是95～155 km 和48～84 km。泥质岩经历了一个区域进变质作用过程。该过程可以被分为三个阶段：① 绿泥石变质脱水阶段；② 角闪石、白云母变质脱水阶段；③ 黑云母变质脱水阶段。在各阶段中，随含水矿物的变质脱水作用不断进行，流体被逐渐从体系中释放出来。最后以黑云母的消失为标志，指示了泥质岩体系变质脱水作用的结束。在俯冲带深部温度压力条件下，泥质岩所释放出的流体以富集Cu、Pb、Nd、Ba等流体活动性元素为主要特征。俯冲带沉积物（岩）在进入到俯冲带深部前，受海水浸染而富集Cl，这导致其在俯冲带深部变质脱水过程中，所释放出的流体中富集Cu、Pb、Rb、Sr、Cs、La、Ba、Ce、Pr、Nd、Sm、Eu等微量元素。而未受到海水浸染或浸染程度较弱俯冲带沉积物，在俯冲带变质脱水过程中所释放出的变质流体中，上述微量元素的富集程度则相对较弱。

高温高压下水热体系中黄铁矿-金原电池的腐蚀电化学原位测量研究

水流体-导电性矿物相互作用是自然界中水流体-固体相互作用的重要组成部分，是许多矿床形成和演化的核心过程。迄今为止，绝大多数地质和地球化学家们对导电性矿物在水流体中的溶解机制普遍存在模糊的认识，认为水流体中导电性矿物的溶解和定位是一种简单的化学溶解和沉淀或简单的氧化溶解和还原定位过程，而实质上导电性矿物（组合）在水流体中的溶解是一种由电极电位差驱使下的类似于金属腐蚀的复杂电化学过程。当具有不同电极电位的矿物在溶液中相互接触，就会形成短路原电池发生电化学腐蚀。其中，电极电位低的矿物作为原电池的阳极，其溶解会加剧，而电极电位高的矿物作为原电池的阴极，其溶解会受到抑制。鉴于前人对水流体-导电性矿物相互作用的腐蚀原电池反应机理的模糊认识，本论文工作基于腐蚀原电池观点对高温高压条件下NaCl水流体体系中黄铁矿与金之间的原电池反应进行了研究。 在本工作中，作者与所在的研究小组一道，首先自行研制了一套可用于高温高压水热体系中导电性矿物腐蚀电化学原位测量的高压釜反应装置。该装置主体部件选用在高温高压下具有高强度、抗腐蚀等优良性能的工业纯钛制成。在该装置中，通过将热电偶直接插入高压釜釜腔内，成功地实现了釜内流体温度的准确测量和精确控制。对高压釜不同部位的测温结果表明，沿高压釜的径向与轴向均存在显著的温度梯度，其中釜塞保护锥体处的温度比釜内流体的温度低约8℃，釜外壁中心处与釜内的温度差约10℃；对400℃保温条件下釜内流体温度的直接测量表明，釜内温度波动小于0.5℃。在该装置中，通过将脆性导电性矿物制作成锥形电极，采用耐高温无机绝缘材料制作密封部件，利用锥体自紧式密封技术，成功地解决了脆性电极和电极引线的高压密封与高温绝缘问题；通过引入另一根辅助性的矿物电极引线，成功地解决了原位监测实验过程中矿物电极与引线接触处是否进水的难题，确保了实验的可信度。可行性试验结果表明，该方法不仅可用于高温高压下水流体-导电性矿物，而且可广泛用于水流体-金属间相互作用的腐蚀电化学原位测量研究。 利用上述自行研制的腐蚀电化学实验装置，本工作对高温高压（250-400℃；10-35 MPa）NaCl水流体体系中黄铁矿-自然金原电池的热力学和动力学进行了实验研究。原位测量结果表明： （1）黄铁矿-金原电池的腐蚀电流变化与其开路电压的变化一致； （2）汽-液平衡条件下，黄铁矿-金原电池的开路电压和腐蚀电流在液相中比在汽相中要大； （3）在温度为400 C、压力远离临界点的过热蒸气和超临界区域，压力在实验研究的范围内（10-35 MPa）对黄铁矿-金原电池的开路电压和腐蚀电流均无显著的影响，随压力的增加两者仅略有增大，但当温度压力跨越临界点时，包括温压从汽-液平衡曲线同时进入超临界区以及温度恒定在400 C、压力跨越临界点时，黄铁矿-金原电池的开路电压和腐蚀电流在临界点附近均发生突变。 （4）在本工作中实验的温度、压力和水流体体系条件下，由黄铁矿与金构成的原电池在大多数情况下黄铁矿为阳极，因此在原电池短路时黄铁矿在水流体中发生氧化溶解，而金则为阴极，在原电池短路时金的溶解受到保护，仅在个别狭窄的温度压力范围内情况才相反。 上述原位测量结果与电极表面水流体的性质以及黄铁矿和金的能带结构密切相关，运用混合电位理论、Butler-Volmer方程以及半导体电化学的波动能级模型对实验结果能进行很好的解释。

高温高压下部分熔融岩石和岩石玻璃弹性波速研究

人类对地球深部结构的认识主要依赖于天然地震的观测资料，高温高压下矿物、岩石和岩浆玻璃的弹性波速测量，是对野外地震波探测资料进行物质反演的重要依据，也为建立地球内部结构模型和地球动力学研究提供重要的实验数据。大量研究证实，高温高压下岩石的部分熔融将形成地震波低速层。然而，前人的研究中，多以岩石的纵波波速（Vp）测量结果来讨论区域地壳结构和低速层的成因，而且很少对实验过程中的中间产物进行观察分析。另一方面，由于玻璃在高温高压下具有特殊的弹性性质，一些科学家推测地球内部岩石的非晶质化也将导致地震波低速层形成。但目前这一推测尚缺乏充分的实验数据支持。为此，作者依托YJ-3000吨大腔体高压实验技术平台，利用脉冲反射法和透射－反射法，完成了： （Ⅰ）三江地区花岗岩和角闪斜长片麻岩在最高压力2.0GPa、最高温度1200℃下的纵波波速（Vp）和最高温度600℃下的横波波速（Vs）研究，并通过岩石物态变化过程中的取样实验，综合探讨岩石中矿物脱水、固－固相变、部分熔融对其弹性波速的影响。获得以下主要结论： ① 花岗岩和角闪斜长片麻岩的Vp和Vs随压力及温度的变化趋势基本一致。室温下岩石的Vp和Vs随压力升高而升高，岩石波速具明显的各向异性，而且其各向异性随压力增大到约0.5GPa后逐渐趋于一恒定值； ② 恒定压力下，岩石的Vp和Vs首先随温度升高近线性缓慢降低，当750℃ 950℃后，石英相变完成，岩石的波速由于熔体含量增加又快速降低； ③ 高温高压下岩石的Vp和Vs研究显示了对三江地区地壳结构一致的约束结果，即该区花岗岩主要分布在上地壳，而角闪斜长片麻岩从上地壳底部到中地壳底部均有分布，这一结果与前人利用Vp研究建立的该区地壳模型基本一致； ④ 在三江地区中上地壳高石英含量的岩石中，石英的α－β相变是地壳地震波低速层形成的主要因素，而随岩石中石英含量的变化，高温高压下岩石的部分熔融及岩石的波速各向异性也可能形成低速层。 （Ⅱ）化学成分从基性到酸性的7种岩石的熔体玻璃在1.0GPa和2.0GPa，最高温度1000℃下的Vp研究和最高温度730℃下的Vs研究。获得以下主要结论： ① 与岩石波速随压力增大而增大不同，室温、0.4－2.0GPa压力下，除两种基性岩石（正长辉石岩和粗面玄武岩）的熔体玻璃外，其它5种中酸性岩石的熔体玻璃的Vp均随压力增大而减小，而这7种玻璃的Vs全部随压力增大而减小。而且，玻璃波速随压力增加而异常降低的幅度随样品中SiO2含量的增高逐渐增大； ② 恒定压力下，随实验温度升高，各种玻璃的弹性波速缓慢降低。当温度高于玻璃转变温度Tg后，玻璃弹性波速的温度系数（∂V/∂T）增大约3倍以上； ③ 研究证实了一种新的地震波低速层成因模式，即上地幔岩石中如果含有超过10vol％的玄武岩玻璃，将会形成地震波低速层；假如下地壳基性岩石中中酸性非晶质体含量超过20vol％，也可能导致地壳低速层的形成。