Ti：Al2O3透明多晶陶瓷光谱特性分析

采用传统无压烧结工艺制备出透明性良好的掺Ti氧化铝陶瓷；测定了该陶瓷的吸收光谱、荧光光谱和激发光谱。结果表明，掺Ti氧化铝透明陶瓷样品在Mg与Ti掺入离子的摩尔比（NMg／NTi）较小时，表现出Ti^3＋离子的490nm特征吸收峰，即^2T2→^2E跃迁产生的宽带吸收；NMg／NTi较大时，陶瓷样品吸收光谱中不存在Ti^3＋离子吸收，其250nm处吸收为O^2-→Ti^4＋的转移吸收。掺Ti氧化铝透明陶瓷样品Ti^3＋离子的发射谱线与单晶的相吻合，同时Ti^3＋在氧化铝陶瓷中分布很均匀，且Ti^3＋浓度较

Cr^4＋在Al2O3透明陶瓷中的发光行为

采用传统无压烧结工艺制备出透明性良好的掺Cr的Al2O3透明陶瓷；测定了其吸收光谱和荧光光谱，发现在Al2O3六配位的八面体结构中，除了有Cr^3＋离子的特征吸收峰外，由于有Mg^2＋的电荷补偿作用，也有Cr^4＋离子，Cr^4＋的荧光发射峰位于1223nm附近，与Cr^4＋在四面体中的发光行为一致。但其荧光发射峰较窄，半高宽△λ仅为37nm。

温梯法蓝宝石（Al2O3）晶体的脱碳去色退火研究

温度梯度法（TGT）生长的Al2O3晶体因石墨发热体在高温时的挥发和原料中过渡性金属离子的存在，晶体在不同部位呈现不同颜色，一般上部为浅红色，尾部为浅黄绿色，将TGT法生长的Al2O3晶体（Ф110×80mm^3）依次经过高温氧化气氛、高温还原气氛脱碳、去色退火实验，即“两步法”退火实验，晶体变成无色、透明，经测试，Al2O3晶体的完整性、光学透过率和光学均匀性均有显著提高。

Diode-pumped passively q-switched Nd : YAG ceramic laser with a Cr4+: YAG crystal-satiable absorber

Transparent polycrystalline Nd:YAG ceramics were fabricated by solid-state reactive sintering a mixture of commercial Al2O3,Y2O3, and Nd2O3 powders. The powders were mixed in ethanol and doped with 0.5 wt% tetraethoxysilane, dried, and pressed. Pressed samples were sintered at 1750 degrees C in vacuum. Transparent fully dense samples with average grain sizes of 10 mu m were obtained. The 1 at.% Nd:YAG ceramic was used to research passively Q-switched laser output with a Cr4+:YAG crystal as a saturable absorber. An average output power of 94 mW with a pulse width of 50 ns was obtained when the incident pump power was 750 mW. The slope efficiency was 13%. The pulse energy is 5 mu J, and the peak power is about 100 W.

Diode-pumped Yb : YAG ceramic laser

Transparent polycrystalline Yb:YAG ceramics were fabricated by solid-state reactive sintering a mixture of commercial Al2O3, Y2O3, and Yb2O3 powders. The powders were mixed in ethanol and doped with 0.5 wt% tetraethoxysilane, dried, and pressed. Pressed samples were sintered at 1730 degrees C in vacuum. Transparent fully dense samples with grain sizes of several micrometers were obtained. The phase from 1500 degrees to 1700 degrees C was important for the grain growth, in which the grains grew quickly and a mass of pores were eliminated from the body of the sample. Annealing was an important step to remove the vacancies of oxygen and transform Yb2+ to Yb3+. The 1 at.% Yb:YAG ceramic sample was pumped by a diode laser to study the laser properties. The maximum output power of 1.02 W was obtained with a slope efficiency of 25% at 1030 nm. The size of the lasering sample was 4 mm x 4 mm x 3 mm.

掺Yb^3＋氧化镧钇透明激光陶瓷的光谱特性

采用传统陶瓷烧结工艺,在无压还原气氛下低温制备出透明性良好的掺Yb^3＋氧化镧钇透明激光陶瓷,测试了其在室温下的吸收光谱、发射光谱和荧光寿命.结果表明,掺Yb^3＋氧化镧钇透明激光陶瓷的吸收系数随着Yb^3＋掺杂浓度的增加而增大,最强吸收峰974 nm处的吸收截面为0.90～1.12×10^-20 cm^2;主发射峰1 032 nm和1 075 nm处的发射截面分别为1.05×10^-20 cm^2和0.87×10^-20 cm^2; Yb^3＋掺杂浓度为5at.%时荧光寿命为1.38 ms,并随Yb^3

用Judd-Ofelt理论计算Nd^3＋掺杂氧化镧钇透明陶瓷的光谱参量

采用传统无压烧结工艺制备Nd^3 ＋掺杂的氧化镧钇透明激光陶瓷,测试了其吸收和荧光光谱.采用Judd-Ofelt理论对Nd^3 ＋掺杂量为1 .5at %的样品光谱参量进行了计算.根据吸收光谱,拟合得到三个强度参量分别为：Ω2=6 .57×10^-20cm^2,Ω4=2 .04×10^-20cm^2,Ω6=4 .38×10^-20cm^2.根据这三个参量计算了样品的辐射寿命,跃迁几率,荧光分支比,量子效率和品质因子,并对结果作了分析.

用纳米粉制备Nd：Y1.84La0.16O3透明陶瓷Nd：Y1

用碳酸盐共沉淀法制备一种新的掺钕氧化镧钇（Nd：Y1.84La0.16O3）纳米粉体,得到颗粒细小、均匀、分散性好、粒径为50～60nm的Nd：Y1.84La0.16O3纳米粉体.分别采用Nd：Y1.84La0.16O3纳米粉料和商业粉料,用传统陶瓷无压烧结工艺制备Nd：Y1.84La0.16O3透明陶瓷.Nd：Y1.8vLa0.16O3纳米粉制备的陶瓷样品的组分均匀、几乎不存在第二相,具有较高的透过率.商业粉制备的陶瓷样品因混料不均匀而在晶界处存在部分第二相,降低了陶瓷的透过率.此外,还运用体视学法预测

晶格匹配氮化镓和氧化锌基外延薄膜衬底材料ScAlMgO4晶体生长研究

采用提拉法成功生长了氮化镓和氧化锌基外延薄膜晶格匹配的ScAlMgO4单晶衬底材料,晶体呈透明白色,尺寸为Ф30mm×59mm,表面部分沿解理面有裂纹.粉末X射线衍射（XRD）分析表明经1400℃固相反应烧结的原料基本合成了ScAlMgO4多晶相.初步的偏光显微镜观察、晶体的粉末XRD表征、透过光谱和双晶摇摆测试表明晶体具有较好的光学性质和结晶质量.研究表明晶体本身的层状结构、较大的温度梯度和热应力的不均匀性是生长过程中引起晶体开裂的几个主要原因.

Yb：YAG透明陶瓷的制备和激光输出

制备了高质量的Yb：YAG透明陶瓷．Yb：YAG透明陶瓷的晶粒尺寸为10μm左右且分布均匀，晶界处和晶粒中没有杂质、气孔的存在．Yb：YAG样品中所有元素分布均匀，不同的晶粒间，晶粒和晶界间成分是一致的，没有出现成分的偏析．4mm厚样品的透过率为80％．LD泵浦获得了波长为1030nm，最大功率为268mW的连续激光输出．

Er^3＋／Yb^3＋共掺的氧化镧钇透明陶瓷的光谱性能研究

采用传统无压烧结工艺制备了Er^3＋／Yb^3＋共掺的氧化镧钇透明陶瓷并对其光谱性能进行了研究．样品具有较大的吸收和发射截面．La2O3的添加使样品的荧光寿命（τs）与玻璃接近，当Yb^3＋和Er^3＋的掺杂量分别为5at％和0．5at％时，测得τs=9．65ms．这种荧光寿命长、发射截面大和线宽窄的特性有利于微型、可集成化和大功率激光输出的实现．

La2O3对Yb：Y2O3透明陶瓷光谱性能的影响

研究了La2O3对Yb：Y2O3透明陶瓷光谱性能的影响，添加适量La2O3以后，Yb：Y2O3透明陶瓷的吸收峰和发射峰的位置不变，但由于La^3＋的离子半径大于Y^3＋的离子半径，在Y2O3中引入La^3＋离子后，导致Y2O3晶格常数变大，晶场强度变弱，同时降低了Y2O3晶体的有序度，致使发射峰强度有所下降，发射截面变小．过量的№La2O3（x=0．16）造成yb^3＋激活离子发射强度明显下降；其荧光寿命在添加La2O3后总体增大45％-60％.

铝酸钇晶体中的生长小面

采用提拉法生长了掺Ce、掺Yb和掺Mn的铝酸钇(YAlO3,YAP)晶体,晶体均完整透明,无肉眼可见的气泡、散射和包裹物等宏观缺陷。通过化学腐蚀和同步辐射白光形貌实验检测了YAP晶体中的生长小面缺陷。结果表明:晶体生长过程中,由于凸向熔体的固-液界面,造成了小面生长现象。沿[101]方向生长的YAP晶体中出现的小面为(102),(201),(121)和(121)奇异面。X射线摇摆曲线表征的结果表明:生长小面的存在严重破坏了晶体的微观结构完整性和均匀性,并导致了小角度晶界缺陷的产生。

Growth and characterization of high-quality LiAlO2 single crystal

g-LiAlO2 single crystal is a promising substrate for GaN heteroepitaxy. In this paper, we present the growth of large-sized LiAlO2 crystal by modified Czochralski method. The crystal quality was characterized by high-resolution X-ray diffraction and chemical etching. The results show that the as-grown crystal has perfect quality with the full width at half maximum (FWHM) of 17.7-22.6 arcsec and etch pits density of (0.3-2.2) x 10(4) cm(-2) throughout the crystal boule. The bottom of the crystal boule shows the best quality. The optical transmission spectra from UV to IR exhibits that the crystal is transparent from 0.2 to 5.5 mu m and becomes completely absorbing around 6.7 mu m wavelength. The optical absorption edge in near UV region is about 191 nm.

Luminescence characteristics of Yb3+, La3+ codoped yttrium oxide nanopowders

Luminescence characteristics of Yb3+, La3+ codoped yttrium oxide nanopowders were investigated. The grain size and the crystallinity of (Yb0.05Y0.90La0.05)(2)O-3 nanopowders increase with the increase of calcination temperature. The average grain size of the nanopowders calcined at 1100 degrees C is 66 nm and its cooperative up-conversion luminescence centered at 498 nm was detected due to nanometer size effect and perfect crystallinity. However, the cooperative up-conversion luminescence of (Yb0.05Y0.90La0.05)(2)O-3 transparent ceramics was not detected. (c) 2008 Elsevier B.V. All rights reserved.