Temperature-independent fiber Bragg grating strain sensor using bimetal cantilever

A new packaged fiber Bragg grating using bimetal cantilever beam as the strain agent is presented. The grating is two-point attached on one specific surface of the bimetal beam which consists of two metallic material with different thermal-expansion coefficient. Thereby the grating can be compressed or stretched along with the cantilever beam while temperature varies and temperature compensation can be realized. At the same time, grating chirping can be avoided for the particular attaching method. Experiment results demonstrated that the device is able to automatically compensate temperature induced wavelength shift. The temperature dependence of Bragg wavelength reduced to -0.4 pm/degrees C over the temperature range from -20 to 60 degrees C. This fiber grating package technique is cost effective and can be used in strain sensing. (c) 2005 Elsevier Inc. All rights reserved.

Experimental study of mode field evolution of dual-core photonic crystal fiber

The accurate mode field profile of high negative dispersion dual-core photonic crystal fiber (DCPCF) is measured. The mode field evolution of DCPCF with wavelength is studied experimentally for the first time. The measurement result shows that no individual inner core mode or outer core mode exists, but two modes coexist simultaneously, and either one of them is dominant. The mode field evolution versus wavelength indicates that the wavelength range where the modes coupling takes place between inner core and outer core is broader than that of theoretical design.

Enhanced Pockels effect in GaN/AlxGa1-xN superlattice measured by polarization-maintaining fiber Mach-Zehnder interferometer

Six-period 4 nm GaN/10 nm AlxGa1-xN superlattices with different Al mole fractions x were prepared on (0001) sapphire substrates by low-temperature metal-organic chemical vapor deposition. The linear electro-optic (Pockels) effect was studied by a polarization-maintaining fiber-optical Mach-Zehnder interferometer system with an incident light wavelength of 1.55 mu m. The measured electro-optic coefficients, gamma(13)=5.60 +/- 0.18 pm/V, gamma(33)=19.24 +/- 1.21 pm/V (for sample 1, x=0.3), and gamma(13)=3.09 +/- 0.48 pm/V, gamma(33)=8.94 +/- 0.36 pm/V (for sample 2, x=0.1), respectively, are about ten times larger than those of GaN bulk material. The enhancement effect in GaN/AlxGa1-xN superlattice can be attributed to the large built-in field at the interfaces, depending on the mole fraction of Al. (C) 2007 American Institute of Physics.

Stabilized and tunable single-frequency erbium-doped fiber ring laser employing external injection locking

A stabilized and tunable single-longitudinal-mode erbium-doped fiber ring laser has been proposed and experimentally demonstrated. The laser is structured by combining the compound cavity with a fiber Fabry-Perot tunable filter. An injection-locking technique has been used to stabilize the wavelength and output power of the laser. One of the longitudinal modes is stimulated by the injected continuous wave so that this mode is able to win the competition to stabilize the system. A minimum output power of 0.6 dBm and a signal-to-noise ratio of over 43 dB within the tuning range of 1527-1562 nm can be achieved with the proposed technique. A wavelength variation of less than 0.01 nm, a power fluctuation of less than 0.02 dB, and a short-term linewidth of about 1.4 kHz have also been obtained.

Novel folding 8x8 silicon-based optical matrix switch with tapered waveguides and self-aligned corner mirrors

Novel folding 8 x 8 matrix switches based on silicon on insulator were demonstrated. In the design, single-mode rib waveguides and multimode interferences are connected by optimized tapered waveguides to reduce the mode coupling loss between the two types of waveguides. The self-aligned method was applied to the key integrated turning mirrors for perfect positions and low loss of them. A mixed etching process including inductively coupled plasma and chemical etching was employed to etch waveguides and mirrors, respectively. The compact size of the device is only 20 x 3.2 mm(2). The switch element with high switching speed and low power consumption is presented in the matrix. The average insertion loss of the matrix is about -21 dB, and the excess loss of one mirror is measured of -1.4 dB. The worst crosstalk is larger than 21 dB. Experimental results illuminate that some of the main characteristics of optical matrix switches are. developed in the modified design, which is in accord with theoretic analyses.

Flat-top arrayed waveguide grating using a tapered multimode interferometer

A 40-channel 0.8-nm-spaced flat-top silica-based arrayed waveguide grating (AWG) with a tapered multimode interferometer (MMI) at the end of its input waveguide has been experimentally demonstrated for the first time. By adding the MMI, the 1-dB and 3-dB bandwidths are increased to 0.45 and 0.62 nm, respectively. The insertion loss (IS) of the device ranges from 3.8 to 6.8 dB. The IS uniformity is better than 3.0 dB. The crosstalk is better than -25 dB. Compared to the AWG with a rectangular MMI, the AWG with a tapered MMI shows better IS, crosstalk, and ripple. (c) 2006 Society of Photo-Optical Instrumentation Engineers.

Electro-optic coefficients of Si0.75Ge0.25/Si/Si0.5Ge0.5 asymmetric superlattice measured by polarization-maintaining fiber-optic Mach-Zehnder interferometer

Ten-period 5.5 nm Si0.75Ge0.25/10.3 nm Si/2.5 nm Si0.5Ge0.5 trilayer asymmetric superlattice was prepared on Si (001) substrate by ultrahigh vacuum chemical vapor deposition at 500 degrees C. The stability of Mach-Zehnder interferometer was improved by utilizing polarization-maintaining fibers. According to the electro-optic responses of the superlattice with the light polarization along [110] and [-110], respectively, both electro-optic coefficients gamma(13) and gamma(63) of such asymmetric superlattice were measured. gamma(13) and gamma(63) are 2.4x10(-11) and 1.3x10(-11) cm/V, respectively, with the incident light wavelength at 1.55 mu m. (c) 2006 American Institute of Physics.

High-quality multiple quantum wells selectively grown with tapered masks by ultra-low-pressure MOCVD

An InGaAsP/InGaAsP multiple quantum wells (MQWs) selectively grown by ultra-low-pressure (22 mbar) metal-organic chemical vapor deposition was investigated in this article. A 46 nm photoluminescence peak wavelength shift was obtained with a small mask width variation (15-30 mu m). High-quality crystal layers with a photoluminescence (PL) ftill-width-at-half-maximum (FWHM) of less than 30 meV were achieved. Using novel tapered masks, the transition-effect of the tapered region was also studied. The energy detuning of the tapered region was observed to be saturated with the larger ratio of the mask width divided to the tapered region length. (C) 2005 Elsevier B.V. All rights reserved.

Size tolerance analysis of a 4X4 tapered multimode interference coupler in a silicon-on-insulator structure

Size tolerance of a 4X4 general interference tapered multimode interference (MMI) coupler in a silicon-on-insulator (SOI) structure is investigated by means of a 2-D finite difference beam propagation method (2D-FDBPM), together with an effective refractive index method (EIM). The results show that the tapered multimode interference coupler exhibits relatively larger size tolerance when light is launched from the edgeport than from midport, though it has much better output power uniformity when light is launched from midport. Besides that, it can reduce the device length greatly. The 4X4 general interference tapered MMI coupler has a slightly larger size tolerance compared with a conventional straight multimode interference coupler. (C) 2003 Society of Photo-Optical Instrumentation Engineers.

Selective-area MOCVD growth for distributed feedback lasers integrated with vertically tapered self-aligned waveguide

The growth pressure and mask width dependent thickness enhancement factors of selective-area MOCVD. grow th were investigated in this article. A, high enhancement of 5.8 was obtained at 130 mbar with the mask width of 70 mum. Mismatched InGaAsP (-0.5%) at the maskless region which could ensure the material at butt-joint region to be matched to InP was successively grown by controlling the composition and mismatch modulation in the selective-area growth. The upper optical confinement layer and the butt-coupled tapered thickness waveguide were regrown simultaneously in separated confined heterostructure 1.55 gm distributed feedback laser, which not only offered the separated optimization of the active region and the integrated spotsize converter, but also reduced the difficulty of the butt-joint selective regrowth. A narrow beam of 9degrees and 12degrees in the vertical and horizontal directions, a low threshold current of 6.5 mA was fabricated by using this technique. (C) 2003 Elsevier Science B.V. All rights reserved.

Tuning the resonant wavelength of long period fiber gratings by etching the fiber's cladding

In this paper the resonant wavelength of a long period fiber grating (LPG) is tuned toward longer wavelength by etching the fiber, For LP04 and LP05 cladding modes', the tuning ranges of 23 and 81 nm are achieved, respectively. Also the dependence of the resonant wavelength on the cladding radius of LPG is theoretically simulated. (C) 2001 Elsevier Science B,V. All rights reserved.

Compact 3-dB tapered multimode interference coupler in silicon-on-insulator

We have fabricated a compact 3-dB multimode interference coupler with a large silicon-on-insulator cross section. To reduce the length of the usual symmetric interference multimode interference coupler, we propose using a parabolically tapered structure. The length of the device is 398 mum. The device has a uniformity of 0.28 dB. (C) 2001 Optical Society of America.

Fabrication of 2 x 2 tapered multimode interference coupler

The authors demonstrate a 3dB 2 x 2 parabolically tapered multimode interference (MMT) coupler with a large cross-section and space between the different ports using silicon-on-insulator technology. The device exhibits a uniformity of < 0.8dB and can be used in the realisation of an MMI-based optical switch with a high extinction ratio.

High power 980 nm Al-free strained quantum-well lasers for erbium-doped fiber amplifiers

In this paper, we reported on the fabrication of 980 nm InGaAs/InGaAsP strained quantum-well (QW) lasers with broad waveguide. The laser structure was grown by low-pressure metalorganic chemical vapor deposition on a n(+)- GaAs substrate. For 3 mu m stripe ridge waveguide lasers, the threshold current is 30 mA and the maximum output power and the output power operating in fundamental mode are 350 mW and 200 mW, respectively. The output power from the single mode fiber is up to 100 mW, the coupling efficiency is 50%. We also fabricated 100 mu m broad stripe coated lasers with cavity length of 800 mu m, a threshold current density of 170 A/cm(2), a high slope efficiency of 1.03 W/A and a far-field pattern of 40 x 6 degrees are obtained. The maximum output power of 3.5 W is also obtained for 100 mu m wide coated lasers. (C) 2000 Elsevier Science B.V. All rights reserved.