Resonance Raman and surface-enhanced Raman spectroscopic study of microperoxidase-11

The electron transfer and structure of microperoxidase-11(MP-11) in solution and at electrode/solution interface were studied by electrochemical, resonance Raman and surface-enhanced Raman spectroscopic techniques. Results show that the central iron in heme group was six-coordinated in solution, whereas it was converted to five-coordinated state as MP-11 was adsorbed on the surface of a roughened silver electrode, due to the reorientation of MP-11 molecules. The electrochemical properties of MP-11 were directly affected by the coordination state of heme iron.

Nanostructure and mechanical measurement of highly oriented lamellae of melt-drawn HDPE by scanning probe microscopy

Scanning probe microscopy was used to simultaneously determine the molecular chain structure and intrinsic mechanical properties, including anisotropic elastic modulus and friction, for lamellae of highly oriented high-density polyethylene (HDPE) obtained by the melt-drawn method. The molecular-scale image of the highly oriented lamellae by friction force microscopy (FFM) clearly shows that the molecular chains are aligned parallel to the drawing direction, and the periodicities along and perpendicular to the drawing direction are 0.26 and 0.50 nm, respectively. The results indicate that the exposed planes of the lamellae resulting from the melt-drawn method are (200), which is consistent with results of transmission electron microscopy and electron diffraction. Because of the high degree of anisotropy in the sample, coming from alignment of the molecular chains along the drawing direction, the measured friction force, F, determined by FFM is strongly dependent on the angle, theta, between the scanning direction and the chain axis. The force increases as theta is increased from 0 degrees (i.e., parallel to the chain axis) to 90 degrees (i.e., perpendicular to the chain axis). The structural anisotropy was also found to strongly influence the measurements of the transverse chain modulus of the polymer by the nanoindentation technique. The measured value of 13.8 GPa with transverse modulus was larger than the value 4.3 GPa determined by wide-angle X-ray diffraction, which we attributed to anisotropic deformation of the lamellae during nanoindentation measurements that was not accounted for by the elastic treatment we adopted from Oliver and Pharr. The present approach using scanning probe microscopy has the advantage that direct correlations between the nanostructure, nanotribology, and nanomechanical properties of oriented samples can be determined simultaneously and simply.

Matrix effects in inductively coupled plasma mass spectrometry by use of organic solvents

Matrix effects arising from ethanol, propanol, glycerol, acetic acid, ethylenediamine and triethanolamine in inductively coupled plasma mass spectrometry have been studied. Addition of ethanol, propanol, glycerol, acetic acid, ethylenediamine and triethanolamine into solution has an enhancement effect on the signal intensity of analyte with ionization potential between 9 and 11 eV. The ethylenediamine and triethanolamine have higher enhancement effect on the signal intensity of Hg than that of ethanol, propanol, glycerol and acetic acid. Addition of ethylenediamine and triethanolamine into solution has a suppression effect on the signal intensity of Ph and Sr. The mechanism of the enhancement or suppression was investigated. The signal enhancement of Hg in the presence of ethylenediamine and triethanolamine is not caused by improved degree of ionization of Hg and nebulization efficiency. The suppression effects of Ph and Sr in the presence of ethylenediamine and triethanolamine are due to decrease of atomization efficiency of these elements. A method for the determination of Hg in the biological standard samples Ly ICP-MS was developed.

Synthesis and electroluminescent properties of a novel terbium complex

A new carboxylic acid ligand (o-amino-4-hexadecane benzoic acid, AHBA) and a corresponding terbium complex (Tb(AHB)(3)) were synthesized and characterized. A multilayer electroluminescent device with poly(N-vinylcarbazole) (PVK), 2-(4-biphenyl)-5-(4-t-butylphenyl)-1,3,4-oxadiazole (PBD) and the terbium complex as emissive layer was fabricated: glass substrate/ITO/PPV/PVK:-To(AHB)(3):PBD/Alq(3)/Al. The photoluminescence (PL) and electroluminescence (EL) spectra were discussed. This EL cell exhibited characteristic emission of terbium ions with a maximum luminance of 35 cd/m(2) at 20 V. (C) 2000 Elsevier Science S.A. All rights reserved.

Identification of high-lying odd energy levels of uranium by resonant ionization mass spectrometry

Single-colour and two-colour multiphoton resonant ionization spectra of uranium atom were studied extensively with a Nd: YAG laser-pumped dye laser atomic beam apparatus time-of-flight mass spectrometer in our laboratory. The energy locations of high-lying odd-parity levels in the region 33 003-34 264 cm(-1),mearured by a two-colour three-step ionization technique, were reported here. The angular momentum quantum number J was uniquely assigned for these levels by using angular momentum selection rules.

Laser-time-resolved fluorescence spectroscopy in immunoassays

This paper described a laser-excited time-resolved fluoroimmunoassay set. It made lanthanide ion to couple the anhydrde of diethylenetriaminepentaacetic acid (DTPAA) for labeling antibodies. The experiment used polystyrene tap coated with HCV antigen as the solid phase and a chelate of the rare earth metal europium as fluorescent label. A nitrogen laser beam was used to excite the Eu3+ chelates and after 60 ys delay time,the emission fluorescence was measured. Background fluorescence of short lifetimes caused by serum components and Raman scattering can be eliminated by set the delay rime. In the system condition, fluorescent spectra and fluorescent lifetimes of Eu3+ beta-naphthoyltrifluroacetone (NTA) chelates were measured. The fluorescent lifetime value is 650 mu s. The maximum emssion wavelength is 613 nm. The linear range of europium ion concentration is 1 x 10(-7)- 1 x 10(-11) g.mL(-1) and the detection limit is 1 x 10(-13) g.mL(-1). The relative standard deviation of determination ( n = 12) for samples at 0.01 ng.mL(-1) magnitude is 6.4%. Laser-TRFIA was also found to be suitable for diagnosis of HCV. The sensitvity and specificity were comparable to enzyme immunoassay. The result was obtained with laser-TRFIA for 29 human correlated well with enzyme immunoassay.

Determination of ultra-trace rare-earth elements in human plasma by inductively coupled plasma mass spectrometry

Inductively coupled plasma mass spectrometry (ICP-MS),a highly sensitive inorgnic analytic technique,fits to determine ultra-nace rare-earth elements in human plasma. Under the optimized conditions detection limits for 15 rare-earth elements are in the range of 0.7 (for Eu)-5.4 (for Gd) ng.L-1. Indium as an internal standard element is used to compensate for matrix suppression effect and sensitivity drift. Three kinds of preparation methods, diluted with 1% HNO3, digested with HNO3-H2O2 and with HNO3-HClO4, are checked and compared,and the former is the simplest way to be measured. The samples diluted with 1% HNO3, stored in 4 degrees C, are very steady for 16 days. With the method, 11 healthy plasma samples in Changchun area of China are analysed.

Modern spectral estimation of ICP-AES

The inductively coupled plasma atomic emission, spectrometry (ICP-AES) and its signal characteristics were discussed using modem spectral estimation technique. The power spectra density (PSD) was calculated using the auto-regression (AR) model of modem spectra estimation. The Levinson-Durbin recursion method was used to estimate the model parameters which were used for the PSD computation. The results obtained with actual ICP-AES spectra and measurements showed that the spectral estimation technique was helpful for the better understanding about spectral composition and signal characteristics.

Hydrogel of biodegradable cellulose derivatives. I. Radiation-induced crosslinking of CMC

Radiation crosslinking of carboxymethylcellulose (CMC) with a degree of substitution (DS) from 0.7 to 2.2 was the subject of the current investigation. CMC was irradiated in solid-state and aqueous solutions at various irradiation doses. The DS and the concentration of the aqueous solution had a remarkable affect on the crosslinking of CMC. Irradiation of CMC, even with a high DS, 2.2 in solid state, and a low DS, 0.7 in 10% aqueous solution, resulted in degradation. However, it was found that irradiation of CMC with a relatively high DS, 1.32, led to crosslinking in a 5% aqueous solution, and 20% CMC gave the highest gel fraction. CMC with a DS of 2.2 induced higher crosslinking than that with a DS of 1.32 at lower doses with the same concentration. Hence, it was apparent that a high DS and a high concentration in an aqueous solution were favorable for high crosslinking of CMC. It is assumed that; high radiation crosslinking of CMC was induced by the increased mobility of its molecules in water and by the formation of CMC radicals from the abstraction of H atoms from macromolecules in the intermediate products of water radiolysis. A preliminary biodegradation study confirmed that crosslinked CMC hydrogel can be digested by a cellulase enzyme. (C) 2000 John Wiley & Sons, Inc.

Lateral habits of single crystals of metallocene-catalyzed low molecular weight short chain branched polyethylene from the melt

The lateral habits of low molecular weight short chain branched polyethylene single crystals from the melt were studied. Three crystallization temperatures (102, 104 and 106 degrees C) were selected for single crystal growth. It was found that the lateral habits of single crystals were asymmetric at all the crystallization temperatures selected. The electron diffraction patterns and tilting series experiments evidenced that there existed chain tilting in all the lamellae. It was the chain tilting that lead to the asymmetry of the growth rate and of lateral habits of the single crystals about the b-axis. The lateral habits substantially changed from the growth at 102 degrees C where the truncated lozenge single crystals formed with straight (110) faces to the growth at 104 degrees C where the lenticular single crystals appeared. This change occurred at 20 degrees C lower than that in a low molecular weight linear polyethylene with the same molecular weight. Furthermore, kinetics theory analysis evidenced that the change of lateral habits from truncated lozenge to lenticular shape resulted from the transition of growth regime. The results were the same as that of high molecular weight linear polyethylene but different to that of low molecular weight linear polyethylene. It may be attributed by the existence of short branched chains. (C) 2000 Elsevier Science Ltd. All rights reserved.

Fullerenes-extracted soot: a new adsorbent for collecting volatile organic compounds in ambient air

Fullerenes-extracted soot (FES) is the by-product of fullerenes production. Retention characteristics at different temperatures for 17 volatile organic compounds (VOCs) on FES are measured. The adsorption and desorption efficiencies for VOCs on FES adsorbent tubes range from 40.8 to 117%, most of them being 100+/-20%. The values are compared with Tenax GR, an adsorbent commonly used in environmental analysis. FES can be used as an adsorbent of low cost to collect VOCs in environmental samples. (C) 2000 Elsevier Science B.V. All rights reserved.

Amperometric glucose biosensor based on lipid film

A novel glucose biosensor based on cast lipid film was developed. This model of biological membrane was used to supply a biological environment on the surface of the electrode, moreover it could greatly reduce the interference and effectively exclude hydrophilic electroactive material from reaching the detecting surface. TTF was selected as a mediator because of its high electron-transfer efficiency, and it was incorporated in the lipid film firmly. Glucose oxidase was immobilized in hydrogel covered on the lipid film. The effects of pH, operating potential were explored for the optimum analytical performance by using amperometric method. The response time of the biosensor was less than 20 s, and the linear range is up to 10 mmol l(-1) (corr. coeff. 0.9932) with the detection limit of 2 x 10(-5) mol l(-1). The biosensor also exihibited good stability and reproducibility. (C) 2000 Elsevier Science S.A. All rights reserved.

The single crystal-like banded textures in the films of a thermotropic liquid crystalline poly(aryl ether ketone) containing a lateral chloro group

The banded textures in the films of a thermotropic liquid crystalline poly(aryl ether ketone) containing a lateral chloro group have been studied by means of transmission electron microscopy(TEM), electron diffraction(ED) and atomic force microscopy (AFM). The crystallization-induced Landed texture without external shear can be formed when the thin films were annealed at the temperature range(320-330 degrees C) of the liquid crystalline state from the melt, The results show that the banded regions have high orientation of single crystal based on the orthorhombic packing and the growing direction of the Lands is along the b axis of the crystals, This kind of single crystal-like bands is due to the different orientation of the packing molecular chains, The molecular chains of the dark bands in the bright field electron micrograph are perpendicular to the film plane, while the ones of the bright Lands are tilt along the b axis with the tilt angle upto +/-20 degrees.

Self-assembled monolayer of polyoxometalate on gold surfaces: Quartz crystal microbalance, electrochemistry, and in-situ scanning tunneling microscopy study

A new kind of inorganic self-assembled monolayer (SAM) was prepared by spontaneous adsorption of polyoxometalate anion, AsMo11VO404-, onto a gold surface from acidic aqueous solution. The adsorption process, structure, and electrochemical properties of the AsMo11VO404- SAM were investigated by quartz crystal microbalance (QCM), electrochemistry, and scanning tunneling microscopy (STM). The QCM data suggested that the self-assembling process could be described in terms of the Langmuir adsorption model, providing the value of the free energy of adsorption at -20 KJ mol(-1). The maximum surface coverage of the AsMo11VO404- SAM on gold surface was determined from the QCM data to be 1.7 x 10(-10) mol cm(-2), corresponding to a close-packed monolayer of AsMo11VO404- anion. The analysis of the voltammograms of the AsMo11VO404- SAM on gold electrode showed three pairs of reversible peaks with an equal surface coverage of 1.78 x 10(-10) mol cm(-2) for each of the peaks, and the value was agreed well with the QCM data. In-situ STM image demonstrated that the AsMo11VO404- SAM was very uniform and no aggregates or multilayer could be observed. Furthermore, the high-resolution STM images revealed that the AsMo11VO404- SAM on Au(lll) surface was composed of square unit cells with a lattice space of 10-11 Angstrom at +0.7 V (vs Ag\AgCl). The value was quite close to the diameter of AsMo11VO404- anion obtained from X-ray crystallographic study. The surface coverage of the AsMo11VO404- SAM on gold electrode estimated from the STM image was around 1.8 x 10(-10) mol cm(-2), which was consistent with the QCM and electrochemical results.

The synthesis of some 1,1 '-ferrocene dichalcogenato complexes containing chromium, molybdenum and tungsten

Both dinuclear [3] ferrocenophane derivatives of the type Fe(C5H4E)(2)[MLn] [E = S,Se; MLn = Cp* - Cr(NO) (1), Cp* Mo(NO) (2a,2b), CpMo(NO) (3), Cp* W(NO) (4a,4b), Ca2Mo (6b), Cp2W (7a)] and trinuclear 1,1' - ferrocene dichalcogenato complexes Fe(C5H4E)(2)[MLn](2)[MLn = Cp* Cr(NO)(2), E = S(8a), Se(8b)] were synthesized and characterized by their IR, H-1 MMR and EI - MS spectra as well as their elemental analyses.