一般广义离散系统动态输出反馈H_∞控制器设计

提出一种用于一般广义离散系统的严格真动态输出反馈H_∞控制器设计方法。首先，构造辅助广义离散系统，给出该系统的状态反馈H_∞控制器设计方法，在此基础上，用两组矩阵不等式给出使一般广义离散系统是允许的且满足H_∞范数限制的控制器存在的充分条件，并给出了控制器的解析表达式。通过解这两组矩阵不等式，即可获得所需的控制器。控制器的可解性条件由系统的系数矩阵表达，因此不需要矩阵分解，可避免由矩阵分解产生的数值问题。仿真结果证实算法的有效性。

基于模型扰动抑制的直线伺服系统设计

针对高精度、微进给永磁直线交流同步电机 (PMLSM )驱动系统 ,采用基于模型的扰动抑制 (MBDA)方法 ,对诸如摩擦力、切削力、负载变动之类的扰动进行抑制。MBDA是利用一个与系统并行的标称模型 ,通过输出反馈 ,将系统输出与标称模型输出进行比较 ,得出误差信号 ,并通过设计一个补偿器将误差信号反馈给被控对象的输入端 ,从而实现扰动抑制。同时 ,针对速度环设计了积分 -比例 (IP)控制器 ,以满足系统快速跟踪指令的要求 ,并且其具有较强的抗扰动能力。仿真结果表明 ,该控制方法响应速度快 ,抗干扰能力强

Theoretical modelling of the effect of photon lifetime on the output dynamics of Er-doped distributed feedback fibre lasers

By employing a simple model of describing three-level lasers, we have theoretically investigated the effect of photon lifetime on the output dynamics of Er-doped distributed feedback fibre lasers. And based on the theoretical analysis we have proposed a promising method to suppress self-pulsing behaviour in the fibre lasers.

Instabilities in a grating feedback external cavity semiconductor laser

Output power fluctuations in a grating external cavity diode laser with Littman configuration are described, showing peculiar chaotic behaviors of self-pulsation at the L-I curve kink points. Different spectral characteristics with multiple peaks are observed at upper and lower state of the self-pulsation. It is found also that P-N junction voltage jumps in a same pace with the pulsation. The observed phenomena reflect competition between different longitudinal modes, and transient variation of transverse modes in addition. These experimental results may contain information about the mechanisms of the chaotic instability in strong filtered feedback semiconductor lasers. (C) 2008 Optical Society of America

Single mode Er-doped pi-phase-shifted distributed feedback fibre grating laser

A novel method incorporating the shielded method and the post-processing method has been proposed to fabricate the pi-phase-shilted fibre grating. Then an Er-doped pi-phase-shifted distributed feedback fibre grating laser has been fabricated using the grating. The laser threshold is 20 mW. When pumped with 90 mW light at 980 nm, the laser gives an output of 1.1 mW. Its signal-to-noise ratio is better than 60 dB. It is demonstrated that the laser is single mode operation by means of a Fabry-Perot scanning interferometer.

Optical properties of zirconia-titania-ORMOSIL films for temperature tuning distributed feedback waveguide lasers

The zirconia-titania-ORMOSIL waveguide thin films with considerable optical quality were prepared by the sol-gel process. The refractive index (n) and the extinction coefficient (k) were determined by a scanning ellipsometer. Wavelength tunable output of distributed feedback waveguide lasing was demonstrated in Rhodamine 6G doped ZrO2 TiO2-ORMOSIL thin films by varying the temperature, and about 5.5 nm wavelength tuning range was achieved around the emission wavelength of 599 nm. The thermal-optic coefficient (dn/dT) of the active ZrO2-TiO2-ORMOSIL films was deduced. (c) 2005 Elsevier B.V. All rights reserved.

Line-width reduction of a laser diode array using an external cavity with two feedback mirrors

A novel Littman-Metcalf external cavity laser diode array with two feedback mirrors is introduced. The line-width broadening effect caused by smile can be reduced by the novel external cavity. At the drive current of 16A, the line-width is narrowed to 0.1nm from free-running width of 1.6nm with output efficiency of 84%.

Distributed Feedback Laser with Sampled Grating

A distributed feedback laser with the sampled grating has been designed and fabricated. The typical threshold current of the sampled grating based DFB laser is 32 mA, and the output power is about 10mW at the injected current of 100 mA. The lasing wavelength is 1.5564 mu m, which is the -1(st) order mode of the sampled grating.

Holographic fabricated photonic-crystal distributed-feedback quantum cascade laser with near-diffraction-limited beam quality

We demonstrate the fabrication and characterization of photonic-crystal distributed-feedback quantum cascade laser emitting at 4.7 mu m. The tilted rectangular-lattice PCDFB structure was defined using a multi-exposure of two-beam holographic lithography. The devices exhibit the near-diffraction-limited beam emission with the full width at half maximum of the far-field divergence angles about 4.5 degrees and 2.5 degrees for stripe widths of 55 mu m and 95 mu m, respectively. Single-mode emission with a side mode suppression ratio of approximate to 20 dB is achieved in the temperature range (80-210 K). The single-facet output power is above 1 W for a 95 mu m x 2.5 mm laser bar at 85 K in pulsed operation. (C) 2009 Optical Society of America

Material growth and device fabrication of highly strained InGaAs/InGaAsP long wavelength distributed feedback lasers

1.6-1.7 mu m highly strained InGaAs/InGaAsP distributed feedback lasers was grown and fabricated by low pressure mentalorganic chemical vapor deposition. High quality highly strained InGaAs/InP materials were obtained by using strain buffer layer. Four pairs of highly strained quantum wells were used in the devices and carrier blocking layer was used to improve the temperature characteristics of the devices. The uncoated 1.66 mu m and 1.74 mu m lasers with ridge wave guide 3 mu m wide have low threshold current (< 15mA) and high output power (> 14mW at 100mA). In the temperature range from 10 degrees C to 40 degrees C, the characteristic temperature T-0 of the 1.74 mu m laser is 57K, which is comparable to that of the 1.55 mu m-wavelength InGaAsP/InP-DFB laser.

1.55-mu m Ridge DFB laser and electroabsorption modulator integrated with buried-ridge-stripe dual-waveguide spot-size converter output

A 1.55-mu m ridge distributed feedback laser and electroabsorption modulator monolithically integrated with a buried-ridge-stripe dual-waveguide spot-size converter (SSC) at the output port for low-loss coupling to a cleaved single-mode optical fiber was fabricated by means of selective area growth, quantum-well intermixing, and dual-core technologies. These devices exhibit threshold current of 28 mA, 3-dB modulation bandwidth of 12.0 GHz, modulator extinction ratios of 25.0-dB dc. The output beam divergence angles of the SSC in the horizontal and vertical directions are as small as 8.0 degrees x 12.6 degrees, respectively, resulting in 3.2-dB coupling loss with a cleaved single-mode optical fiber.

10 GHz optical short pulse generation using tandem electroabsorption modulators monolithically integrated with distributed feedback laser by ultra-low-pressure selective area growth

In this work, a novel light source of tandem InGaAsP/InGaAsP multiple quantum well electroabsoption modulator( EAM ) monolithically integrated with distributed feedback laser is fabricated by ultra-low-pressure ( 22 x 10(2) Pa ) selective area growth metal-organic chemical vapor diposition technique. Superior device performances have been obtained, such as low threshold current of 19 mA, output light power of 4.5 mW, and over 20 dB extinction ratio at 5 V applied voltage when coupled into a single mode fiber. Over 10 GHz 3dB bandwidth in EAM part is developed with a driving voltage of 2 V. Using this sinusoidal voltage driven integrated device, 10 GHz repetition rate pulse with an actual width of 13.7 ps without any compression elements is obtained due to the gate operation effect of tandem EAMs.

High-Power Distributed Feedback Laser Diodes Emitting at 820nm

By etching a second-order grating directly into the Al-free optical waveguide region of a ridgewaveguide（RW） AlGaInAs/AlGaAs distributed feedback（DFB） laser diode,a front facet output power of 30mW is obtained at about 820nm with a single longitudinal mode. The Al-free grating surface permits the re-growth of a high-quality cladding layer that yields excellent device performance. The threshold current of these laser diodes is 57mA,and the slope efficiency is about 0.32mW/mA.

Offset quantum-well method for tunable distributed Bragg reflector lasers and electro-absorption modulated distributed feedback lasers

A two-section offset quantum-well structure tunable laser with a tuning range of 7 nm was fabricated using offset quantum-well inethod. The distributed Bragg reflector （DBR） was realized just by selectively wet etching the multiquantum-well （MQW） layer above the quaternary lower waveguide. A threshold current of 32 mA and an output power of 9 mW at 100 mA were achieved. Furthermore, with this offset structure method, a distributed feedback （DFB） laser was integrated with an electro-absorption modulator （EAM）, which was capable of producing 20 dB of optical extinction.